Practical Analog and RF Electronics 2020020919, 2020020920, 9780367542917, 9781003088547
This is a book about real-world design techniques for analog circuits: amplifiers, filters, injection-locked oscillators
540 160 29MB
English Pages 226 [227] Year 2020
Table of contents :
Cover
Half Title
Title Page
Copyright Page
Dedication
Table of Contents
Preface
About the Author
Chapter 1 Operational, RF, and Current Amplifiers and Their Ubiquity
1.1 Introduction
1.2 The Op-Amp and Its Real and Imaginary Parasitics and Compensation
1.3 Real and Imaginary Parasitics
1.4 Compensation
1.5 The Inverting Mode
1.6 The Non-Inverting Mode and Its SNR Advantage over the Inverting Mode
1.7 The Operational Transconductance Amplifier
1.8 The Transistor as a Transconductance Amplifier
1.9 Short-Circuit Transfer Impedance
1.10 Reciprocity of the Three-Terminal Feedback Network
1.11 Using the Miller Effect to Realize a Capacitance Neutralizer
1.12 Viewing the Transistor as a Current Conveyor
1.13 The More Complex the Architecture the Slower the Speed
1.14 Shot Noise and Transconductance and Impact on Signal-to-Noise Ratio
1.15 Resistor Noise
1.16 The Darlington Configuration for RF Amplification
1.17 Non-Small-Signal Amplifiers
1.17.1 Class C
1.17.2 Class F Power Amplification with Higher Efficiency
1.18 Gyrators
1.19 Current Conveyor Approach to High Dynamic Range and High Gain-Bandwidth Product
1.20 Linearity
1.21 Physical Layout and Parasitics Caused by Layout
1.22 Early Integrated Popular Op-Amps and the Ua709 (by Bob Widlar)
1.23 Transistor Issues
Chapter 2 Transimpedance Amplifiers for Low Noise
2.1 Introduction
2.2 Motivation
2.3 Resistor Bandwidth
2.4 Cascode Input Stage
2.5 Tricks when Bandwidth Is Insufficient
2.6 Input Node Capacitance Issue Drives Noise
Chapter 3 Voltage-Controlled Amplifiers
3.1 Introduction
3.2 Log/Antilog Approach
3.3 Blackmer VCA
3.4 Talbot VCA for High Bandwidth
Chapter 4 Emitter Followers and Source Followers (FETs)
4.1 Introduction
4.2 Model for a Bipolar Junction Transistor (BJT) (Emitter Capacitor Loaded) Simplified
4.3 Potential Oscillation in BJT Emitter Follower and Explanation
4.4 Actual Simulation of Field Effect Transistor Source Follower Showing Oscillation
Chapter 5 Equally Terminated Two-Port Reciprocal Networks and Reversal of Input and Output
5.1 Introduction
5.2 What Is Meant by Equally Terminated (Doubly Terminated)
5.3 Example of a Reciprocal Two-Port Network Driven by Equal Source and Load Impedance
5.4 Simulation of Network s21 and s12 (Gain in Either Direction) Showing s12 = s21
5.5 Asymmetry of Components Makes s11s22 (Example Figure 5.1)
5.6 Symmetry of Components Makes s11 = s22, with Example
Chapter 6 Importance of Terminating Filters Properly
6.1 Introduction
6.2 Single Termination of Simplest LC (Inductor-Capacitor) Second Order Lowpass Filter
6.2.1 Frequency Response for the Case of Peaking (Voltage Gain before Rolloff)
6.3 Frequency Response for the Case of No Peaking
6.4 Lesson: Even Such a Simple Network Behaves Radically Different for Incorrect Termination
6.5 Sometimes This Filter Is Useful for Its Peaking Ability to Make a Narrow Band Transformer
6.6 An Equally-Terminated (Doubly-Terminated) Filter Can Never Have Voltage Gain
Chapter 7 Diode Detector Flatness
7.1 Introduction
7.2 Diode Detector Configurations that Do Not Work
7.3 Peak Detector Configuration Yields the Flattest Response
Chapter 8 Passive Filters
8.1 Introduction
8.2 LC Passive Filters
8.3 Types of Filters: Lowpass, Highpass, Bandpass, Bandstop, and Allpass
8.4 Forms of Filters: Butterworth, Chebyshev, Thompson, Elliptic, and Cauer
8.5 Group Delay
8.6 First Order Group Delay Equalizer
8.7 Second Order Group Delay Equalizer
8.7.1 Tank Circuit Definitions
8.8 Circuit Structure for Possible Passive Second Order Delay Equalizer at High Frequencies
8.9 Delay Compensation of Fifth Order Cheby LPF
8.10 First Order Group Delay Compensator
8.11 Filters Derived by Subtracting Other Filters
8.12 Notch Networks (Traps) with Infinite Depth
8.13 Transforming a Lowpass Filter into a Bandpass Filter
8.14 Impedance Scaling a Filter
8.15 Frequency Scaling a Filter
8.16 Simple Method of Impedance Matching
8.17 Saw Filters
8.18 Sallen-Key Inspired Third Order Filters
8.19 Tone Burst Response of a Notch Network or LPF
8.20 State Variable Filters
Chapter 9 Secant Waveform for Synchronous Demodulation
9.1 Introduction
9.2 Conventional Use of the Cosine Waveform for Synchronous Demodulation
9.3 Secant Waveform for Local Oscillator
Chapter 10 Receiving NRZ Data Using AC Coupling
10.1 Introduction
10.2 Edge Detection
10.3 Delay Line and Differencer
10.4 SNR Considerations
Chapter 11 Gilbert Gain Cell Versus RF Mixer
11.1 Introduction
11.2 Balanced Modulator or RF Mixer
11.3 Gilbert Gain Cell and Linear Multiplier
11.4 “Plain Vanilla” Gilbert Cell
Chapter 12 Passive Components
12.1 Introduction
12.2 Resistors
12.3 Inductors
12.4 Capacitors
12.5 Resonators
12.6 Computing Microphonics Due to Sinusoidal Vibration
Chapter 13 Unwanted Sidebands Effect on Adjacent Channel(s)
13.1 Introduction
13.2 Explanation
Chapter 14 Injection Locking
14.1 Introduction
14.2 Details
Chapter 15 Phase-Locked Loops
15.1 Introduction
15.2 The Most Popular Second Order Type 2 PLL
15.3 False Locking Prevention for Sweeping PLL
Chapter 16 Distortion Fundamentals and Spectral Regrowth
16.1 Introduction
16.2 Second Order Distortion
16.3 Third Order Distortion
Chapter 17 Optimization
17.1 Introduction
17.2 Introduction to Curve Flattening
17.3 Shaping Frequency Response between Two Boundaries
17.4 Conclusion
Chapter 18 Quadrature Distortion and Cross-Rail Interference
18.1 Introduction
18.2 Standard Amplitude Modulation (AM) Broadcast Reception with Sideband Asymmetry
18.3 Cross-Rail Interference
Bibliography
Index
