Geometry and its Applications in Arts, Nature and Technology [2 ed.] 9783030613976, 9783030613983

Table of contents :
Preface
A very personal foreword
Self-sufficient geometry?
A sixth sense
Descriptive geometry and more
Acknowledgments – the network
Table of Contents
Introduction
Where geometry matters
Level of detail
The website
1 An idealized world made of simple elements
1.1 Points, lines, and circles in the drawing plane
Zero-dimensional spheres
Rays without beginning or end
Circles
The most natural curve
Triangles
Congruent and similar triangles
One of the oldest theorems of geometry
The circle steps out of line
Directly congruent figures, twisted into each other
Similar figures, twisted into each other
1.2 Special points inside the triangle
A circle through three points – the circumcenter
The centroid: a point of physical significance
The orthocenter: a point of geometric significance
All three points are guaranteed to lie on a straight line
The incenter – or: a circle on three tangents
Two ways of defining a circle are still missing . . .
▸▸▸ Two nontrivial circle constructions
A circle through nine (!) points in the triangle
The beer mat method
A point of high importance
How can an arbitrary triangle be converted into an equilateral triangle?
▸▸▸ An inventive tessellation
Are there other methods to convert an arbitrary triangle into an equilateral triangle?
The dilemma of angle trisection
Points at infinity
1.3 Elementary building blocks in space
Surfaces without curvature
1.4 Euclidean space
Basic terms and axioms
A pillar of little support
The sum of distances
The Apollonian circles
Harmonic points
All that remains is the product
From the plane into three-dimensional space
Analogies on the sphere
Other distance lines and distance surfaces
1.5 Polarity, duality and inversion
Infinity can mean many things
A close relationship
The principle of duality
An infinite amount and infinitely more
Inversion – not every transformation is linear
An allegedly inexplicable “anomaly”
A mechanism for the realization
Spherical reflection
Purism
▸▸▸ A proof that isn’t: appearances can be deceiving . . .
1.6 Projective and non-Euclidean geometry
Let us discard lengths and angles
The dimensional jump
Ranges of points and pencils of straight lines
Projectivity = likewise linearity
A conic section always remains a conic section
The line at infinity is suddenly “completely normal”
Non-Euclidean geometry
What’s so fascinating about this?
Geometry on the sphere
The curvature of space
2 Projections and shadows: Reduction of the dimension
2.1 The principle of central projection
The points in space are pushed into a plane
Points at infinity are absolutely normal
Points can “disappear”
What happens to straight lines?
A linear mapping
The mapping only works in one direction
From my perspective . . .
A closer examination of objects at infinity
Central projection of planes
2.2 Parallel projection and normal projection by means of restriction
▸▸▸ A simple depiction by means of a horizontal projection
▸▸▸ Reconstruction of a spatial situation based on shadows
▸▸▸ Radar corner reflectors and cat’s eyes
▸▸▸ Mirror optics instead of refractive lenses
2.3 Assigned normal projections
▸▸▸ Which object is it?
▸▸▸ Simple construction of the unfolding
▸▸▸ Assignment problems?
▸▸▸ Shadows on the coordinate-parallel screen planes
▸▸▸ What is broken or dislocated?
▸▸▸ Shadows provide additional information
Determination of visibility for skew straight lines
2.4 Principal lines and the Law of Right Angles
▸▸▸ Non-trivial right angles in a cuboid
▸▸▸ An abundance of right angles . . .
▸▸▸ If and only if
▸▸▸ Luggage X-ray scans – are they normal projections?
▸▸▸ The crescent does not seem to be facing the Sun (Fig. 2.45)
▸▸▸ When exactly do spring and the other seasons begin (Fig. 2.46)?
▸▸▸ Topographic projection
2.5 The difference in technical drawing
▸▸▸ Special additional views
▸▸▸ Virtual sections
▸▸▸ Multiple virtual sections
▸▸▸ Dimensioning
▸▸▸ Sections in construction drawings
3 Polyhedra: multi-faced and multi-sided
3.1 Congruence transformations
3.2 Convex polyhedra
Prisms and pyramids
A series of simple properties
▸▸▸ Shadows of prisms and pyramids
Combination of several convex bodies
▸▸▸ Acceleration of computer programs
Multiple light sources
▸▸▸ Shadow profiles
When do we speak of a polyhedron?
Euler characteristic
3.3 Platonic solids
As simple as it gets
Three objects from equilateral triangles
The last Platonic solid whose beauty defies description
▸▸▸ Dualization of Platonic solids
3.4 Other special classes of polyhedra
Archimedean solids
▸▸▸ Tiling of space
▸▸▸ Different designs of a soccer ball
Rhombic polyhedra
▸▸▸ More polyhedra consisting of congruent rhombuses?
Catalan solids
▸▸▸ Folding
▸▸▸ Foldable flower vases and pots
3.5 Planar sections of prisms and pyramids
▸▸▸ A flexible interactive installation from an Archimedean solid
4 Curved but simple
4.1 Planar and space curves
Basics from planar curve theory
▸▸▸ A circle as an evolute
▸▸▸ Osculating circles of the ellipse
▸▸▸ A curve can be its own evolute
▸▸▸ We steadily rotate the steering wheel
▸▸▸ Envelopes of circles
▸▸▸ Polarizing curves
▸▸▸ Offset curves
▸▸▸ Architectural design using curves
The theory of space curves
▸▸▸ The simplest space curve
Space curves can create surfaces
Contour and outline of a surface
▸▸▸ Why do highlights occur on curved surfaces?
How can the curvature of a surface be measured?
Polygon mesh on a sphere
▸▸▸ A moderately equal distribution of points on the sphere
▸▸▸ Triangulation as a powerful tool
▸▸▸ Geodesic lines – the shortest connection
How can we recognize a developable surface?
Analogous considerations for shadows
4.2 The sphere
▸▸▸ The position of an airplane
▸▸▸ The “spatial Pythagoras”
▸▸▸ Newton’s kissing number problem
Outline and shadow of a sphere
▸▸▸ The tilt of the slender moon crescent – a “result of temperature”?
▸▸▸ Spheres and spherical parts everywhere . . .
The shortest path on a sphere
▸▸▸ From Vienna to Varadero
4.3 Cylinder surfaces
The tried-and-true cylinder of revolution. . .
. . . and general cylinders
4.4 The ellipse as a planar intersection of a cylinder of revolution
A classic proof of spatial geometry
A multitude of applications
Of course, it doesn’t work every time
▸▸▸ Shadows as intersection curves
The process of development. . .
. . . and its inversion (rolling up the development)
5 More about conic sections and developable surfaces
5.1 Cone surfaces
The development of a cone of revolution
▸▸▸ Rolling up onto a cone
▸▸▸ An unbalanced dumbbell rolling on a plane
▸▸▸ A plane rolling on a cone
▸▸▸ Connecting cone between a rectangle and a circle
▸▸▸ The jet of a hairdryer
▸▸▸ The cone according to
A theorem with great technical applicability
5.2 Conic sections
Planar sections of a cone of revolution
What is a degenerate conic section?
▸▸▸ Various definitions of conics
Focal points
Parabolas and catenaries
▸▸▸ Square wheels
How many elements do we need in order to determine a conic section?
When do we get an ambiguous solution?
The inverse paper strip method
Ellipse and hyperbola with axes given by a line element
▸▸▸ Construction of conic sections via spatial interpretation
Construction of the conic sections
▸▸▸ What does an ancient column have to do with an ellipse?
▸▸▸ “Angular distorted” conic sections
▸▸▸ Shadows on a wall
▸▸▸ Parabolic trajectory
▸▸▸ Why are the orbits of planets ellipses?
5.3 General developables
Developables of constant slope
▸▸▸ Function graphs with constant slope
▸▸▸ Star-shaped surfaces with locally constant slope
How is a developable strip created?
▸▸▸ Creating paper strips
▸▸▸ “Development of a developable”
▸▸▸ Approximation of a curved surface through rectangular strips
Let us generate arbitrary developable surfaces
▸▸▸ Developable connecting surfaces
▸▸▸ The connecting developable of two circles
Reflections on a developable surface
▸▸▸ Shiny generators on aluminum cylinders
▸▸▸ Glowing curves
▸▸▸ Light games in the water
▸▸▸ Reflecting compact discs – and curious effects
5.4 Maps and “sphere developments”
The dilemma regarding the development of doubly curved surfaces
▸▸▸ Is it developable after all?
An angleand circle-preserving projection
A practical map
▸▸▸ From Bangalore to Buenos Aires
▸▸▸ The shortest connection
The inversion at a circle from a “higher perspective”
5.5 Reflection in a circle, a sphere, and a cylinder of revolution
▸▸▸ Reflection in a plane
▸▸▸ Reflection in a curved surface
▸▸▸ Reflection in a cylinder of revolution
▸▸▸ Reflection in a sphere
▸▸▸ Conic sections with given focal points that touch a given circle
▸▸▸ Focal lines of a circle
6 Prototypes
6.1 Surfaces of degree two
▸▸▸ A new arm for Eva
Ellipsoids
▸▸▸ The shape of the Earth
▸▸▸ Ellipsoids in dome construction
▸▸▸ Ellipsoids in industrial design
Listening and focusing . . .
▸▸▸ Whispering bowls and odd acoustic phenomena
Paraboloids
▸▸▸ “Receiving dishes”
▸▸▸ Parabolic headlights and sun collectors
Parabolic translation surfaces
Classically beautiful and very useful
Hyperboloids
▸▸▸ The envelope of a rotating cube (Fig. 6.30)
▸▸▸ Result of rows of points on circles in parallel planes
▸▸▸ Stable and light-weight
▸▸▸ Generalization of the generation
▸▸▸ Geodesics on ellipsoids
▸▸▸ Saturn’s shape and its rings
▸▸▸ Cubic circle
▸▸▸ Movements on and around triaxial ellipsoids
▸▸▸ Moving along the generator of a degree-two surface
6.2 Three types of surface points
Curvature of a planar curve
In space, curvature is not at all easy to define!
Principal curvatures
Osculating parabolas lead to an important theorem
▸▸▸ An exciting experiment
▸▸▸ Light edges
▸▸▸ Revolvability with practical consequences
6.3 Surfaces of revolution
▸▸▸ Vase with an ellipse as its finishing part
▸▸▸ Distorted wine barrel
▸▸▸ When geometers take a walk in nature . . .
The torus is a frequent building block of higher degree
Non-trivial sections of the torus
6.4 The torus as a prototype for all other surfaces of revolution
▸▸▸ Contact lenses and astigmatism
Cusps of contours
Intersection of surfaces of revolution
Reverse engineering
▸▸▸ Gauss map
▸▸▸ Automatic detection of developables
6.5 Pipe and channel surfaces
How to invent a new class of surfaces . . .
Pipe surfaces and blending surfaces
▸▸▸ Blending surfaces
▸▸▸ The altitudes of a tetrahedron lead to an aesthetic lamp
7 Further remarkable classes of surfaces
7.1 Ruled surfaces
Conoids
Two important and two beautiful applications
▸▸▸ A spatial version of the theorem of the angle of circumference
7.2 Helical surfaces
The fascination behind the helix
When straight lines or circles undergo a helical motion . . .
▸▸▸ The DNA double helix
Different types through different directions of the straight line
There exists only one type of developable helical surface
It is possible to apply screw motions to circles or spheres
▸▸▸ The secret of DNA
7.3 Different types of spiral surfaces
Helispiral motion
The classical spiral motion
The contour of a spiral surface
The relation to the helix
7.4 Translation surfaces
Translation surfaces as the loci of chord midpoints
Paraboloids as translation surfaces
The helicoid as a translation surface
Other surfaces of revolution that are also translation surfaces
▸▸▸ Regarding rhombuses and huge towers
7.5 Minimal surfaces
The principal curvatures must be of equal magnitude at each point
▸▸▸ Hyperbolic paraboloids are “almost” minimal surfaces.
▸▸▸ Roofs of minimal surfaces
▸▸▸ Sturdy sculptures with lightweight modules (Fig. 7.74)
▸▸▸ -noids
▸▸▸ “Area-minimizing surfaces”
▸▸▸ An algebraic minimal surface and “something similar”
Bending surfaces into each other
▸▸▸ Bending of minimal surfaces
▸▸▸ Bending of nudibranches and algae
8 The endless variety of curved surfaces
8.1 Mathematical surfaces and free-form surfaces
Function graphs
More general surfaces described by mathematical equations
Different types of surfaces
The addition and subtraction of surfaces
Milled surfaces are also “mathematical surfaces”
How can we solve the problem?
Surface theory is helpful in the creation of categories
▸▸▸ Playing with geometric forms
▸▸▸ The shape of a virus
8.2 Interpolating curves and surfaces
▸▸▸ Growth spurts
Direct modeling at the computer
8.3 Bézierand B-spline-curves
Bézier curves
Rational Bézier curves
B-spline curves
Rational B-spline curves (NURBS)
8.4 Bézierand B-spline surfaces
Generalized Bézier surfaces
▸▸▸ Practical construction
▸▸▸ Nutshells made of plastic
8.5 Surface design done differently
An interplay between art and geometry
A different kind of architectural draft
9 Photographic image and individual perception
9.1 The human eye and the pinhole camera
9.2 Different techniques of perspective
Intersection method
▸▸▸ Shadow constructions in perspective
▸▸▸ Shadow of sidelight and general central projection
Measuring points
▸▸▸ Reconstruction from a photo
▸▸▸ Spatial reconstruction with a given image of a cuboid
▸▸▸ Anamorphoses
▸▸▸ Deliberate distortions in computer graphics
The image of a circle
Circle depictions in ancient times
9.3 Other perspective images
Optical illusions
▸▸▸ The Gaussian collineation: Virtual 3D images
▸▸▸ Two different sequences
▸▸▸ Geoglyphs in the desert sand
▸▸▸ Baroque illusions
▸▸▸ Dynamic Sphere – the illusion of a sphere
▸▸▸ We are only measuring angles!
▸▸▸ Star signs
▸▸▸ The spider on the sphere
▸▸▸ The silhouette of a sphere
▸▸▸ Hyperbolas as silhouettes of spheres?
▸▸▸ When silhouettes of spheres are always circles
▸▸▸ “Smoothing” undesirably extreme perspective images
Image on a sphere
▸▸▸ The geometry of the fish eye
9.4 Geometry at the water surface
Adapted eyes
Reflection at the surface
The Snell-Descartes law of refraction
Image raising
Projecting planes
▸▸▸ Reconstruction with two eyes underwater
Submerged
Refraction at curved (spherical) transitional layers
▸▸▸ The optical system of our eyes
▸▸▸ How does insect vision work?
▸▸▸ A pinhole camera is actually enough!
▸▸▸ The small step towards a real camera
10 Kinematics: Geometry in motion
10.1 The pole around which everything revolves
Constrained motion of two points
▸▸▸ Two-point guidance with a bicycle
Two path normals are sufficient
▸▸▸ Two-point guidance with the bicycle (continuation)
Instantaneous velocity
Envelopes
Relative motion
10.2 Different mechanisms
Let us shake hands!
Two-bar linkages
▸▸▸ The chess-playing android
▸▸▸ The joints of articulate animals
▸▸▸ Leonardo’s cranes
The hinge parallelogram
▸▸▸ Pantograph
Antiparallelograms
It does not always have to be a uniform rotation . . .
The crank shaft
▸▸▸ How fast is the piston?
▸▸▸ Sawmill by Leonardo da Vinci
General four-bar linkages (hinge quadrangles)
▸▸▸ Film gripper
▸▸▸ A useful fixing mechanism (“Mole grips” or “Vise-Grips”)
▸▸▸ The front tires have to be rotated asynchronously!
▸▸▸ Cognate linkages
▸▸▸ A sugar bowl and a four-bar linkage
▸▸▸ How to translate a continuous rotation into an intermittent rotation
If the arms could change their length
▸▸▸ A hinge quadrangle with a single variable
▸▸▸ The Stewart platform
10.3 Ellipse motion
▸▸▸ Construction of paper strips
▸▸▸ Ellipses as hypotrochoids
▸▸▸ Gliding or rolling along straight lines
▸▸▸ Revolving a Reuleaux triangle inside a square
▸▸▸ Drilling quadratic holes in practice
▸▸▸ Milling machine for ellipses
▸▸▸ Oval mill by Leonardo
▸▸▸ A compact coupling
▸▸▸ Ellipses produced by a crank shaft gear
▸▸▸ Ellipse compass according to
▸▸▸ Another ellipse compass
General ellipse motion
▸▸▸ Revolution within a triangle or a pentagram
▸▸▸ The world’s first seven-sided coin
10.4 Trochoid motion
▸▸▸ Wankel’s engine
▸▸▸ Planetary motion
▸▸▸ Planetary gears: plenty of angular momentum
▸▸▸ Involute gears
Cycloids (trochoids) at a higher level
11 Spatial motions
11.1 Motions on the sphere
▸▸▸ The star handle in motion (a rotation about a general axis)
▸▸▸ The Cardan shaft
▸▸▸ A sophisticated ball joint
▸▸▸ “Mad House”
Construction on the sphere
11.2 General spatial motion
Two rotations about skew axes
▸▸▸ An earnest effort on a tiny scale
▸▸▸ The Stewart platform in space
▸▸▸ And yet it moves!
▸▸▸ Non-rigid connections
▸▸▸ “As if it were turned by gears”
11.3 What is the position of the Sun?
Does the Sun not rise in the east and set in the west?
First of all, the facts
Let us now simplify several things
Two important auxiliary theorems
▸▸▸ The locus of all possible sun positions
▸▸▸ Determination of the angle between the Earth’s axis and the sunrays
▸▸▸ Sunrise and sunset
▸▸▸ At which angle of elevation does the Sun culminate?
The incidence of light at a given moment
▸▸▸ Where is south?
▸▸▸ A tiny and versatile gem on your necklace
A constant and a varying angular velocity
The equation of time
▸▸▸ Detective games
▸▸▸ Two comparable and yet slightly different photographs
▸▸▸ When are we allowed to measure an angle in a perspective image?
The path of the Moon on the firmament
▸▸▸ The path of the Moon in the solar system
▸▸▸ What is different on the southern hemisphere?
▸▸▸ Multiple circuits around Antarctica
11.4 Minute-precise sundials for identifying the mean time
True and mean time
Simple sundials
The equation of time
The Bernhardt sundial
Cycloid sundial for mean time
The Pilkington-Gibbs sundials
11.5 Kinematics in the animal kingdom
▸▸▸ Inverse kinematics
▸▸▸ Locomotion in mammals and large birds
▸▸▸ Gripping, biting, and shredding
▸▸▸ Kinematic four-link chain in the monitor lizard head
▸▸▸ How to extend the mouth to a long tube?
▸▸▸ Unfolding the wings
12 A variety of filling patterns
12.1 Ornaments and symmetry groups
Frieze ornaments
Plane symmetry groups
12.2 Periodical tilings
Regular
gons as basic building blocks
▸▸▸ From shark skin to flow-optimized architecture
▸▸▸ Tiling with paintings
▸▸▸ Alteration of the sides of a basic building block
Irregular polygons as basic building blocks
Tiling based on an arbitrary n-gon
Tiling with an arbitrary pentagon
Tiling with an arbitrary hexagon
Periodical tilings with multiple basic forms
12.3 Non-periodical tilings
Self-similar aperiodical tilings
Central aperiodical tiling
Quasiperiodical tilings
▸▸▸ Semi-regular pentagons
▸▸▸ Semi-regular dodecahedrons
▸▸▸ Filling the gaps with scutoids
12.4 Non-Euclidean tilings
What is the situation on the sphere?
▸▸▸ From a dodecahedron to an original and easily manufacturable lamp
▸▸▸ Puzzles in space
13 The nature of geometry and the geometry of nature
13.1 Basic geometric forms in nature
Symmetry
Circles as distance curves and path curves
Spheres and other convex basic forms
Minimal and maximal packets
A maximum of food for the offspring. . .
Don’t roll away!
Unrolling and development
13.2 Evolution and geometry
Mutation
Inheritance
The sum is what matters
Phyllotaxis, or: How easily are we deceived?
A premature conclusion
A completely different explanation
The development is not always clearly visible
13.3 Planetary paths and fish swarms
▸▸▸ Geometry as nature’s artistic inspiration
▸▸▸ Organic architecture
13.4 Scaling behavior in nature
13.5 Musical harmony through the eyes of geometry
▸▸▸ Displaying a tonal system on a torus
▸▸▸ The “grid of keys”
▸▸▸ Three-dimensional circle of fifths
▸▸▸ Tonal centers
▸▸▸ Inverted retrograde canons
14 More applications
14.1 Multiple reflections, illusions, and impossibles
▸▸▸ Multiple reflections in two orthogonal mirrors
▸▸▸ Reflection of a water wave
▸▸▸ What exactly happens between two parallel mirrors?
▸▸▸ Analyzing a selfie
▸▸▸ Vision underneath the surface
▸▸▸ Winding to the left or winding to the right?
Illusions and impossibles
▸▸▸ Hexagons and cubes
▸▸▸Zoetropes
▸▸▸The Freemish crate, also called Escher’s cube
▸▸▸The Penrose triangle, also known as the Penrose tribar
▸▸▸Does this work in perspective images, i.e., in photographs?
▸▸▸Perspective illusions
▸▸▸Rolling upwards?
▸▸▸Inside or outside?
14.2 More about inversions in space
Inversion in a sphere
▸▸▸ Inversion of a torus
▸▸▸ Inversion of cylinder and cone of revolution
▸▸▸ An almost extraterrestial figure
▸▸▸ The loxodromes on a sphere
▸▸▸ Inversion of a clothoid
▸▸▸ Sterographic projection of a clothoid
▸▸▸ Inversion in a cylinder (axial involution)
14.3 Voronoi structures
▸▸▸ Iterative Voronoi structures
▸▸▸ Some classic examples in nature
▸▸▸ Voronoi diagrams on the sphere
▸▸▸ Iterated Voronoi diagrams as a tool to find good point distributions
▸▸▸ Voronoi diagrams in 3-space
An alternative algorithm
14.4 Hexagons on a sphere
▸▸▸ A compound eye under the magnifying glass
▸▸▸ How to tile a sphere with hexagons and some pentagons
▸▸▸ How to tile a sphere exclusively with hexagons
▸▸▸ How to cover a surface with squares or circles
14.5 Fractals
▸▸▸ The Koch snowflake
▸▸▸ Plane-filling curves of dimension two
▸▸▸ Soft coral (gorgonia)
▸▸▸ Camouflage in coral environments
▸▸▸ Fractals on spheres and similar surfaces
▸▸▸ The Mandelbrot set
▸▸▸ Julia sets
▸▸▸ Tree fractals
▸▸▸ Ferns
▸▸▸ Fractal expansion
▸▸▸ The Menger sponge
▸▸▸ Sierpinski fractals
▸▸▸ Percolation
A Geometrical freehand drawing
A.1 Normal view vs. oblique view
Why the oblique view is not our ultimate goal
Isometry
The advantage of a normal projection
The engineer’s view – dimetrical and descriptive
The general solution
▸▸▸ Circles with axes parallel to the coordinate axes
A.2 Don’t be afraid of curved surfaces
Unfamiliar at first. . .
. . . but soon highly advantageous!
It does not get any more difficult
▸▸▸ One-sheeted hyperboloid of revolution
▸▸▸ Beam connection
▸▸▸ Pencil tip
▸▸▸ Helical stairs
▸▸▸ Surfaces of revolution
▸▸▸ Blossom of a lily
A.3 Shadows
▸▸▸ Parallel shadows of a cuboid
▸▸▸ Parallel shadows of cylinders and cones
A.4 Perspective sketching
Reducing the level of difficulty
The method of Renaissance artists
The most important terms
Frontal perspective image
▸▸▸ The “square-grid method”
Perspective images with a horizontal viewing axis
Scaffolding
▸▸▸ A helical staircase in a perspective view
Shadows in perspective images
Reflections
Three principal vanishing points
B Geometry and photography
B.1 Focal lengths and viewing angles
Focal lengths and the viewing angle are connected
▸▸▸ Entire lens systems work like one single converging lens
B.2 3D images in photography?
Are photographs central projections?
An impossible photograph
The lens formula
The plane of sharpness scans the object
B.3 Stereoscopy
Optical illusions with one eye closed
Binocular vision
Stereoscopic vision
The brain readjusts images with collinear distortions
A robust illusion
To put everything into perspective. . .
B.4 When should we use which focal length?
A significant difference
Subjective changes in proportion
From one extreme to the other. . .
. . . or: How a broom closet may be turned into a dining hall
Unintended caricatures and passport photographs
Which focal length should we use underwater?
Depth is crucial
Macro photography underwater
B.5 Primary and secondary projection
Ultra-wide-angle images are occasionally necessary!
Cinema screens and portable TVs
Leonardo’s dilemma
B.6 From below or from above?
Either a shift lens . . .
. . . or some geometrical know-how
▸▸▸ An ad showing long female legs
B.7 Collinear distortion of a photo
B.8 The problem with the rolling shutter
▸▸▸ Can you trust photographs?
▸▸▸ When the shadows do not match
▸▸▸ What every “high-speed photographer” needs to know
▸▸▸ The problem lies in the proximity to reality
▸▸▸ The man that shoots faster than his shadow
▸▸▸ An extremely slow rolling shutter
▸▸▸ What does the image of a rotating straight line look like?
▸▸▸ Photo finish
▸▸▸ Possibilities to avoid the rolling shutter effect
Literature
Quoted literature
Additional recommended books
Picture credits
Index

Citation preview

Georg Glaeser

Geometry and its Applications in Arts, Nature and Technology

Geometry and its Applications in Arts, Nature and Technology

Georg Glaeser

Geometry and its Applications in Arts, Nature and Technology Second Edition

Georg Glaeser Department of Geometry University of Applied Arts Vienna Vienna, Austria

Originally published by Springer Wien New York, 2012 ISBN 978-3-030-61397-6 ISBN 978-3-030-61398-3 (eBook) https://doi.org/10.1007/978-3-030-61398-3 Mathematics Subject Classification (2020): 51, 53, 68, 78, 85, 92, 97 © Springer Nature Switzerland AG 2020 This work is subject to copyright. All rights are reserved by the Publisher, whether the whole or part of the material is concerned, specifically the rights of translation, reprinting, reuse of illustrations, recitation, broadcasting, reproduction on microfilms or in any other physical way, and transmission or information storage and retrieval, electronic adaptation, computer software, or by similar or dissimilar methodology now known or hereafter developed. The use of general descriptive names, registered names, trademarks, service marks, etc. in this publication does not imply, even in the absence of a specific statement, that such names are exempt from the relevant protective laws and regulations and therefore free for general use. The publisher, the authors, and the editors are safe to assume that the advice and information in this book are believed to be true and accurate at the date of publication. Neither the publisher nor the authors or the editors give a warranty, expressed or implied, with respect to the material contained herein or for any errors or omissions that may have been made. The publisher remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. This Springer imprint is published by the registered company Springer Nature Switzerland AG The registered company address is: Gewerbestrasse 11, 6330 Cham, Switzerland

Preface A very personal foreword Ever since I was young, I have been fascinated by geometric forms – be they abstract, forms in arts, or forms that occur in nature or technology. Despite having always been a “half biologist”, I decided to study mathematics and geometry, because I realized that they are mighty tools to describe nature.

At the age of 17 (that is, in 1972), I had – amid numerous books about animals – three books by Walter Wunderlich in my bookshelf: Descriptive Geometry I and II and Planar Kinematics ([27], [28]). I was fascinated by perspective drawings of bridges and accurate constructions of snail shells, as well as by the geometry of motion. Back in those days, there were no computers on the market, and everything had to be drawn by hand, which required not only patience but also extensive knowledge.

vi

Preface

In the course of the many years that followed, I have realized that this has been of great advantage to me: Since learning to program a computer is not hard for mathematicians – you only need to apply the structured thinking that determines your whole approach to the tackled problems – computers have become a new and very efficient tool to support the solution of the tasks – no more, no less. The underlying brainwork, paired with spatial imagination, still remains the most important issue. Mainly during the 1990s, I developed graphics tools for the fast visualization of geometric problems by means of the computer, working in part with my colleagues Hellmuth Stachel and Hans-Peter Schröcker ([3], [4], [5]). A predecessor of this book was published in German in 2005, with two more editions in 2007 and 2014 ([6]). In between those publications there was one English edition by Springer Verlag Wien-New York in 2012 ([7]). Each edition had more applications and new topics, thus eventually increasing the number of pages from 400 to 700. Some of the topics are described in more detail in [8] and the two “compendia” about conics and quadrics ([16], [22]) which I wrote together with Hellmuth Stachel and Boris Odehnal.

Self-sufficient geometry? Geometry is usually considered to be one branch of mathematics. Indeed, the mental processes required for geometry are closely related to mathematical logic. Furthermore, since geometry is a very comprehensive field, it is often thought of as an independent science. In any case, geometry and mathematics complement each other quite nicely. Nevertheless, no special mathematical knowledge is required in order to read and understand this book. Whatever mathematical equipment we need will arise by itself. Geometry can be conducted in several ways, but the kind of geometry that we use in this book seeks to utilize the reader’s three-dimensional imagination as often as possible. Such imagination is present to varying degrees in different people, but research has shown that a preoccupation with geometry can improve one’s spatial imagination considerably. You will sometimes find notes in small print about analytical geometry or calculus, but these instances will only serve as reinforcement of ideas that should already have been established by your three-dimensional imagination.

A sixth sense Since geometry not only utilizes but also improves this “sixth sense” of spatial imagination, younger readers often find it easier to progress in this discipline compared to other branches of mathematics. The latter require very solid foundational knowledge, as errors that may be overlooked by inexperienced eyes may lurk in every line of calculation. The kind of geometry with which we are concerned, however, always yields results which can, to some extent, be verified by our imagination. It is for this reason that geometric (“synthetic”) proofs are usually preferred to strictly mathematical (“analytic”) ones. It is by no means uncommon for these proofs to contain such deep levels of

Preface

vii

understanding that new or additional results inevitably come to the attentive mind.

Descriptive geometry and more My concept is based on the ideas of my academic teacher Walter Wunderlich and my predecessor Erich Frisch, who both have, in traditional ways, constructed a simple yet thorough educational framework concerning “descriptive geometry”. Yet, time never stands still, and due to the revolution of geometry brought about by the triumph of computing, their concepts needed to be considerably modified and expanded upon. In this book, I wish to maintain a strong connection to the related fields of computer graphics and computational geometry, which both owe their roots to classical geometry. Furthermore, the geometry that is described in this book shall not be limited to mere depiction, especially since the methodology for the creation of images has so profoundly changed in the digital age.

Acknowledgments – the network I would like to especially thank my co-workers Boris Odehnal for his corrections of the manuscript and for fruitful geometric discussions, and Franz Gruber – who has passed away too early – who contributed to the book by providing a lot of wonderful interactive animations that allow a deeper insight in geometric processes. My former co-workers Christian Perrelli, HansPeter Schröcker, Gerhard Karlhuber, and Thomas Backmeister have also contributed images to this book. Further help came from Wilhelm Fuhs, Herbert Löffler, and Michael Schrott. Several illustrations were created by Harald Andreas Korvas, Zorica Nicolic, Otmar Öhlinger, Markus Roskar, Paulo Tosold, and Stefan Wirnsperger. The final proofreading of this second English edition was done by Eugenie Maria Theuer, Tamara Radak, and Irene Karrer. I was assisted in this endeavor by several colleagues at the Technical University of Vienna (Fritz Manhart and Walter Jank). Walter Hofmann made a valuable contribution to the topic of sundials. Andreas Rüdinger, who represented the German publisher on this project, has been very constructive throughout this book’s development. I am privileged to teach at the University of Applied Arts in Vienna, where I can count renowned artists like Zaha Hadid, Hans Hollein, Oliver Kartak, Bernhard Leitner, Greg Lynn, Paolo Piva, Wolf D. Prix, Hani Rashid, Cristina Díaz Moreno, and Efrén García Grinda among my (partly former) colleagues. Several examples in this book are inspired by their creative work. I am also grateful to have enjoyed further assistance by my colleagues Klaus Bollinger, Ernst Maczek-Mateovits, Roland Burgard, and Marcus Bruckmann. Furthermore, I would like to thank the students at the University of Applied Arts Vienna, who, in a generous interplay of give and take, were always keen

viii

Preface

to contribute ideas, several of which eventually came to fruition. Some of their work is also presented in this book. Finally, my then 12-year-old daughter Sophie has contributed several drawings (e.g., Fig. 3.64) and several models (Fig. A.4). Due to my unceasing enthusiasm for photography this book has become a sort-of “picture book of geometry”. Good photos rarely emerge “by themselves”, or require the unwieldy power of expensive photographic equipment. What is needed is a lot of patience, a good eye, and – as I will show in the appendix – an understanding of geometry. Vienna, June 2020

This picture series of the Moon was taken a month before the completion of this edition, in the midst of the “Corona crisis”. Since almost all airplanes were grounded and there was virtually no pollution during the crisis, the sky was clearer than it had ever been in the years before. Due to the different day times – or better night times – at which the pictures were taken, the colors of the Moon and the sky vary. The last image is a composition of a waxing crescent and a waning gibbon.

Table of Contents . . . . . .

. . . . . .

. . . . . .

. . . . . .

. . . . . .

5 6 13 25 28 34 45

2 Projections and shadows: Reduction of the dimension 2.1 The principle of central projection . . . . . . . . . . . . . . . . 2.2 Parallel projection and normal projection by means of restriction 2.3 Assigned normal projections . . . . . . . . . . . . . . . . . . . 2.4 Principal lines and the Law of Right Angles . . . . . . . . . . . 2.5 The difference in technical drawing . . . . . . . . . . . . . . .

. . . . .

. . . . .

. . . . .

. . . . .

53 54 58 66 75 83

3 Polyhedra: multi-faced and multi-sided 3.1 Congruence transformations . . . . . . 3.2 Convex polyhedra . . . . . . . . . . . 3.3 Platonic solids . . . . . . . . . . . . . 3.4 Other special classes of polyhedra . . . 3.5 Planar sections of prisms and pyramids

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

87 . 88 . 93 . 103 . 109 . 118

4 Curved but simple 4.1 Planar and space curves . . . . . . . . 4.2 The sphere . . . . . . . . . . . . . . . 4.3 Cylinder surfaces . . . . . . . . . . . . 4.4 The ellipse as a planar intersection of a

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cylinder of revolution .

. . . .

. . . .

. . . .

. . . .

125 126 149 161 164

1 An idealized world made of simple elements 1.1 Points, lines, and circles in the drawing plane 1.2 Special points inside the triangle . . . . . . 1.3 Elementary building blocks in space . . . . . 1.4 Euclidean space . . . . . . . . . . . . . . . 1.5 Polarity, duality and inversion . . . . . . . . 1.6 Projective and non-Euclidean geometry . . .

. . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

. . . . . .

. . . . .

5 More about conic sections and developable surfaces 5.1 Cone surfaces . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Conic sections . . . . . . . . . . . . . . . . . . . . . . . . 5.3 General developables . . . . . . . . . . . . . . . . . . . . . 5.4 Maps and “sphere developments” . . . . . . . . . . . . . . 5.5 Reflection in a circle, a sphere, and a cylinder of revolution

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

175 176 185 201 217 226

6 Prototypes 6.1 Surfaces of degree two . . . . . . . . . . . . . . . . . . . . 6.2 Three types of surface points . . . . . . . . . . . . . . . . 6.3 Surfaces of revolution . . . . . . . . . . . . . . . . . . . . 6.4 The torus as a prototype for all other surfaces of revolution 6.5 Pipe and channel surfaces . . . . . . . . . . . . . . . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

233 234 259 268 278 287

7 Further remarkable classes of surfaces 7.1 Ruled surfaces . . . . . . . . . . . 7.2 Helical surfaces . . . . . . . . . . . 7.3 Different types of spiral surfaces . . 7.4 Translation surfaces . . . . . . . . 7.5 Minimal surfaces . . . . . . . . . . 8 The 8.1 8.2 8.3 8.4 8.5

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

293 294 302 315 322 326

endless variety of curved surfaces Mathematical surfaces and free-form surfaces Interpolating curves and surfaces . . . . . . Bézier- and B-spline-curves . . . . . . . . . Bézier- and B-spline surfaces . . . . . . . . Surface design done differently . . . . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

337 338 347 351 354 358

. . . . .

. . . . .

. . . . .

. . . . .

x

Table of Contents

9 Photographic image and individual perception 9.1 The human eye and the pinhole camera 9.2 Different techniques of perspective . . 9.3 Other perspective images . . . . . . . 9.4 Geometry at the water surface . . . . . 10 Kinematics: Geometry in motion 10.1 The pole around which everything 10.2 Different mechanisms . . . . . . 10.3 Ellipse motion . . . . . . . . . . 10.4 Trochoid motion . . . . . . . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

363 364 367 381 401 415

revolves . . . . . . . . . . . . . . . 416

. . . . . . . . . . . . . . . . . . . . 423 . . . . . . . . . . . . . . . . . . . . 440 . . . . . . . . . . . . . . . . . . . . 450

11 Spatial motions 11.1 Motions on the sphere . . . . . . . . 11.2 General spatial motion . . . . . . . . 11.3 What is the position of the Sun? . . 11.4 Minute-precise sundials for identifying 11.5 Kinematics in the animal kingdom . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . the mean time . . . . . . . . . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

459 460 468 473 493 503

12 A variety of filling patterns 12.1 Ornaments and symmetry groups 12.2 Periodical tilings . . . . . . . . . 12.3 Non-periodical tilings . . . . . . 12.4 Non-Euclidean tilings . . . . . .

. . . .

13 The 13.1 13.2 13.3 13.4 13.5

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

511 512 515 522 530

nature of geometry and the geometry of nature Basic geometric forms in nature . . . . . . . . . . . Evolution and geometry . . . . . . . . . . . . . . . Planetary paths and fish swarms . . . . . . . . . . . Scaling behavior in nature . . . . . . . . . . . . . Musical harmony through the eyes of geometry . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

533 534 541 546 552 556

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

14 More applications 14.1 Multiple reflections, illusions, and impossibles 14.2 More about inversions in space . . . . . . . 14.3 Voronoi structures . . . . . . . . . . . . . . 14.4 Hexagons on a sphere . . . . . . . . . . . . 14.5 Fractals . . . . . . . . . . . . . . . . . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

559 560 574 581 589 595

A Geometrical freehand drawing A.1 Normal view vs. oblique view . . A.2 Don’t be afraid of curved surfaces A.3 Shadows . . . . . . . . . . . . . A.4 Perspective sketching . . . . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

607 608 615 622 624

B Geometry and photography B.1 Focal lengths and viewing angles . . . . B.2 3D images in photography? . . . . . . . B.3 Stereoscopy . . . . . . . . . . . . . . . B.4 When should we use which focal length? B.5 Primary and secondary projection . . . . B.6 From below or from above? . . . . . . . B.7 Collinear distortion of a photo . . . . . . B.8 The problem with the rolling shutter . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

. . . . . . . .

637 638 642 653 658 665 670 675 678

Bibliography

. . . .

. . . .

. . . .

685

Introduction Where geometry matters Naturally, there exist many cross connections between geometry and technical disciplines such as mechanical engineering, architecture, and civil engineering. The fields of fine arts and design are likewise influenced by or dependent on geometry, to say nothing of physics, astronomy, geography, chemistry, biology, and molecular biology. All of these fields utilize geometry to derive new insights or to visualize existing ones. Even harmonic relationships in music can be depicted in purely geometrical terms. • When should geometric questions be pursued at a lower dimension? The rotation about a straight line can be imagined much more effectively if the line appears as a point. If the underlying procedure is properly understood, many problems can be simplified. • When, on the other hand, should we look at a problem from a “higher level”? The planar conic sections – when spatially considered – are barely different. Beings inhabiting higher dimensions would, thus, consider many of our differentiations to be superfluous.

Conic sections

Creation of a geoglyph

• How could the ancient Peruvians have created their enormous geoglyphs without having had to invent the equivalent of a hot-air balloon? A combination of central projection and central dilatation made it possible.

Light refraction on the eye

How many photos are required?

• How does vision actually work, and how is it reproduced by a camera? What conditions need to be met so that the image in a photograph seems

2

Introduction

“natural” and not distorted or flattened? Five hundred years ago, Leonardo da Vinci and Leone Battista Alberti , who worked with exact spatial projections to planes, already asked these questions. • When can a distorted photo be “rectified”? How many photos are required in order to reconstruct the true shape of an object? Such questions are not only interesting to architects, but also to the designers of 3D scanners. • What does a map where the shortest distances between pairs of points on the globe appear as straight lines or as circular arcs look like? From what maps can the course angle be directly deduced? Such problems arise from the fact that spheres cannot be unfolded into planes without certain distortions. All of cartography depends on such geometrical insights.

Maps and shortest distances

Good triangulation

• Modern architects today are fond of designing curved buildings. Can geometry be used to minimize the potentially horrendous construction costs resulting from this artistic choice?

Constant velocity joint

Motion of the Earth about the Sun

• How can the rotation about an axis be transmitted to another axis, and how can this transition be accomplished in a smooth manner? This question arises frequently in mechanical engineering. • Why does it not always take the equal amount of time for the Sun to reach its point of culmination? This question from the field of astronomy is partially related to physics, but it involves geometry to an even greater degree. • “Through each point, there exists exactly one parallel to a predefined line.” What happens if one removes this unprovable geometrical axiom? It results in the outlandish field of “non-Euclidean geometry”, the insights of which are even relevant to modern physics!

3

Introduction

Hyperbolic geometry

Snails and horns

• The helical structure of DNA has become the symbol of modern biotechnology. What can be deduced about the growth of snails from the general shape of their shells?

Extreme perspectives

The trick with tilt-shift lenses

• Using simple geometrical tricks, how can you create pictures which would otherwise require an expensive tilt-shift lens? Why is the correct selection of focal distance not only a matter of “visibility”? When are ultraperspectives not only allowed but necessary? Why does sharpness depend on a camera’s aperture? These and many other questions will be broached and answered in this book. Contemporary students have the advantage of computer programs which allow them to visualize graphics that they would otherwise have to painstakingly draw by hand. Therefore, the balance of geometrical education should always tilt in favor of geometrical comprehension and the analysis of its many processes. Such a change in the curriculum allows teachers to address topics that, while relevant to the future professional experience of students, could not have been addressed otherwise due to time restrictions.

Level of detail I have made a great effort to describe laws and rules as simple as possible, before delving into additional details, exceptions, and special cases. For example, I first state the following (p. 62): “If two lines are parallel in two different parallel projections, then they are, in general, also parallel in three-dimensional space.” Exceptions are addressed subsequently – in this important case, in considerable detail. Further examples: If a curve is “not bent”, it means that it has a mathematical curvature of zero. Or: “Each planar section of a sphere is a circle.” Of course, if the plane merely touches the sphere, then the circle shrinks to a so-called “null circle”, which can also be considered a point. But what if the plane

4

Introduction

does not intersect the sphere? Mathematicians can prove that this yields an “imaginary” circle. But how can such an abstract idea be expressed without overstraining the layman? If such exceptions are left unsaid, the interested reader will still understand the idea, and the fundamental assertion remains concise and to the point!

The website www.uni-ak.ac.at/geometrie This book is accompanied by a website. There you will find updates, weblinks to many specialized topics, and further examples of geometry in action. Finally, a plethora of interactive programs is provided that let you visualize many complex sequences of motion and physical simulations. The advantage of such additional material is obvious: First of all, the website is constantly updated, and the material is continually enriched and expanded upon without having to change the book to which it refers. I hope that you will find a lot of useful material on the website and provide me with feedback from which I can further improve this service!

The geometrical net . . .

1

An idealized world made of simple elements

In this chapter, we will learn about the most important building blocks of the geometric world: points, straight lines, and circles in the two-dimensional drawing plane, as well as planes, circles, spheres, cylinders, and cones of revolution in three-dimensional space. Points in geometry are “infinitely small” and, therefore, have no expansion. In the same sense, straight lines are always “infinitely thin” – as well as “infinitely long”. Analogies can be made for planes, cylinders and so on: Mathematically idealized versions simplify how we deal with these objects in our imagination. In geometry, we are not afraid to use the term infinity. Likewise, the abstract concept of dimension is very frequently invoked: A set of planes in 3-space forms a three-dimensional plane space. The theoretical foundation for this statement is given by projective geometry, with which we shall deal in the last section. First, we will define certain terms in the drawing plane and further deepen our understanding by considering some remarkable examples of the geometry of triangles. This should provide a good basis for a smooth transition to spatial geometry. During this process, we shall gain numerous insights by generalizing our results from planar geometry. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_1

5

6

An idealized world made of simple elements

1.1 Points, lines, and circles in the drawing plane Zero-dimensional spheres Points in geometry (and anywhere in mathematics) are “infinitely small” and, therefore, have no expansion. As such, they can be seen as zero-dimensional objects. When we label points, we will adhere to European convention and utilize Latin capital letters such as A, B, P , Q, etc.

Rays without beginning or end By stringing together an infinite number of points – in a given direction – we get an infinitely thin and infinitely long one-dimensional straight line. It can be said that a straight line is “generated” by translating a point. According to European convention, straight lines are labeled using Latin lower-case letters such as a, b, g, h, etc. Straight lines are not bounded segments: Each line segment P Q lies on an infinitely long carrier straight line g = P Q. In order to get accustomed to geometrical language, we will now review some terms that we have already used so far.

Circles Circles are so-called lines of constant distance from a point. All points on the circle k have the same constant distance from the midpoint M , namely the radius r. In this book, we will usually notate circles using the letter k. When we speak of more than one circle, they are notated as k1 , k2 , . . . or kA , kB , kM , . . . (given the midpoints A, B or M ). Circles possess the attribute of being uniformly curved and, like all curves, they are also infinitely thin.

The most natural curve

Fig. 1.1 Water waves

Circles are very popular elements of construction because it is comparatively easy to work accurately with them. Straight lines are rarely found in nature.

1.1 Points, lines, and circles in the drawing plane

7

Circles in the plane or spheres in space are frequent by comparison. One only needs to throw stone pebbles into a lake to be amazed by the concentric rings that are then formed by the wave peaks. All types of waves, including light waves and sonic waves, expand in a circular manner in the plane and spherically in three-dimensional space. It would be impossible to draw long straight lines on a desert island. A forked twig or crotch, however, will let us draw circles rather easily. The alleged last words of Archimedes (about 287–212 B.C.) come to mind: “Do not disturb my circles!” (He was referring to his constructions in the sand, directing his statement at the Roman soldier who, after the conquest of Syracuse, stabbed him to death despite an order to spare his life.)

Fig. 1.2 It is difficult to find straight lines – especially triangles – in nature. This elongated puddle of water froze overnight, forming remarkable geometric shapes.

Triangles A triangle is a union of three points A, B, C that are not on one line. It can equally be described by the three line segments that are formed by the three points: AB = c, BC = a, and CA = b. All other parameters, such as the angles α = ∢BAC, β = ∢ABC, and γ = ∢ACB, can thus be calculated or constructed. This book prefers construction to calculation because, instead of yielding mere numbers, this method produces a “residual” that may be useful for further contemplation.

Congruent and similar triangles Let us construct a triangle ABC where the lengths of its sides are given: We can orient the side AB in any way we like (such as horizontally) and draw two circles kA and kB with the radii AC and BC. If the given lengths of the triangle’s sides are mathematically possible (the sum of the length of two sides must exceed the third), we will get two solutions for the third vertex (C1 and C2 , Fig. 1.3). These two solutions do not differ by size (hence, they are called congruent) but by “orientation”: They are “reversely congruent”. By drawing the parallel to AB through C, we will also notice that: The sum of angles in a triangle equals 180○ .

8

An idealized world made of simple elements

Fig. 1.3 Congruent solutions

Fig. 1.4 Similar triangles, theorem of intersecting lines

⊕ Remark : Fig. 1.5 shows both sides of a peacock’s feather (see also Fig. 6.65). Their distinct pattern is not caused by color pigmentation but is actually the effect of a complex “twisting” of single hairs. The two sides are not identical, but their outlines are certainly similar (the figures in the image are reversely congruent). When considered spatially, it nevertheless remains the same object, which, interestingly enough, is directly congruent. ⊕

Fig. 1.5 Peacock’s feather (front and back side) – reversely congruent?

The term similarity generalizes the notion of congruence. Two triangles are similar if they possess identical angles. The side lengths may change, but a relationship can immediately be established using a factor of similarity. Here, the theorems of intersecting lines are applicable. These simple statements are surprisingly difficult to prove: For this, we need so-called axioms, which are unprovable but commonsense statements that must be accepted as true. Let us consider a triangle ABC, whose side lengths a, b, c are multiplied by a constant factor k (the factor of similarity), resulting in a similar triangle A1 B1 C1 (Fig. 1.4): a1 = k a, b1 = k b, c1 = k c. Triangles with a constant aspect ratio are considered similar. In addition, the following applies: AB ∶ A1 B1 = AC ∶ A1 C1 = BC ∶ B1 C1

1.1 Points, lines, and circles in the drawing plane

9

If we translate one triangle into the other in such a way that the legs of an angle of the first triangle overlap the respective angle of the second triangle, then the remaining two sides are parallel. Thus, we have the Theorems of intersecting lines: If an angle is intersected by two parallel lines, then the ratio of the distances AB and AB1 on the first leg and the respective distances AC and AC1 on the second leg are equal. Furthermore, we have the same ratio on the parallel sections BC and B1 C1 .

One of the oldest theorems of geometry Contemporary geometry, with its strict requirements for proof, dates back to the ancient Greeks, whose science dominated the southern Mediterranean (from Sicily through Asia Minor right down to northern Egypt). Alexandria (in the Nile delta) was seen as their scientific capital. Even before Egypt became hellenized, it was visited by Thales of Milet (625–546 B.C., Asia Minor), who gained much geometric knowledge from there. The realization that a logical proof should be required for every geometric theorem was a great breakthrough for geometry and mathematics. Among other things, Thales proved the famous theorem that bears his name but was known long before him: Thales’s theorem: All angles in a semicircle are right angles. Put in a different way: From each point on the circle, the diameter appears at a right angle. Proof : Let us consider an arbitrary rectangle ABCD, as in Fig. 1.6. By definition, rectangles only have right angles at each vertex (AB ⊥ BC). The diagonal AC has the length d. It is obvious that this rectangle possesses a “circumcircle” with radius d/2, the midpoint of which lies at the intersection of the diagonals. Thus, if seen from the point B (as well as D), AC appears at a right angle. If we now look at all rectangles with an equally long diagonal d, we get the same result every time. Of all these rectangles, we can always overlay both the diagonal and the circumcircle. B and D thus pass through the circumcircle. ⊙

This theorem forms the basis for many further proofs. Thales’s theorem is merely a special case of the following situation: Theorem of the angle of circumference: From each point of a circle, a fixed chord of the circle is always seen at the same angle or from its supplementary angle. Proof : Let ABM be an isosceles triangle with ∢AM B = ϕ. Then ∢BAM = ∢ABM = ψ = 1/2(180○ − ϕ). Let us now draw a circle around M through A and B and pick an arbitrary point C on it. We now have two further isosceles triangles AM C and BM C. If δ and ε describe the same angles of these tri-

10

An idealized world made of simple elements

Fig. 1.6 Thales’s theorem

Fig. 1.7 Theorem of the angle of circumference

angles, then γ = ∢ACB = ε − δ. The sum of all angles in a triangle ABC is [ψ − δ] + [ε + ψ] + [ε − δ] = 180○ . Thus, we get 2(ε − δ) = ϕ or γ = ϕ/2 (= constant). If C resides on the other side of AB, then the following is true for the angle sum of ABC: [δ − ψ] + [δ + ε] + [ε − ψ] = 180○ and thus γ = δ + ε = 180○ − ϕ/2. ⊙

As a by-product of this proof, we can derive the Modification of the theorem of the angle of circumference: From the circumcenter of a triangle, each triangle side is visible under a central angle which is twice the inscribed angle in the opposite vertex. ⊕ Remark : Proving Thales’s theorem was not necessary: it is merely a special case of the theorem of the angle of circumference. However, it is always useful to practice different techniques of proof. In [9] you can find a proof for this theorem that is “kinematic” in nature – much like the proof of Thales’s theorem: If one parameter is changed, the point traces a curve, which in this case is a circle. We will particularly benefit from such considerations in the chapter about kinematics. ⊕

The circle steps out of line Circles play a fundamental role in the classical geometry of Euclid . They intersect a straight line twice at the most. If the straight line merely touches the circle, the points are actually infinitely close to each other. Likewise, two distinct circles never share more than two points. This is as self-evident as it is unusual – at a later point, we will find out why this is the case. At any rate: Most classical constructions can be subdivided in such a way that they can be reassembled merely by intersecting straight lines and circles with other straight lines and circles. Such problems are then either totally linear (if no circles are required) or quadratic or even more than that. The construction of a triangle whose side lengths are given is quadratic because two (reversely congruent) solutions are obtained by intersecting circles.

1.1 Points, lines, and circles in the drawing plane

11

Directly congruent figures, twisted into each other

Fig. 1.8 Directly congruent figures. Right side: With two-sided and two-colored candles, it is not immediately evident that both parts were cast using the same mold.

We will need the following elementary theorem later: Two directly congruent figures (same orientation) in the plane can always be transformed into each other by an unambiguously defined translation and/or rotation. Proof : Let us pick two directly congruent triangles ABC and A∗ B ∗ C ∗ (Fig. 1.8 on the left) on top of the two congruent figures and try to overlap them via rotation. In order to determine the center of rotation, we will need to employ the perpendicular bisector . This is the straight line that runs through the midpoint of P Q, at a right angle to P Q. It is the locus of all points which are equidistant to P and Q. If ABC and A∗ B ∗ C ∗ describe two congruent triangles, then the center Z of rotation has to be equidistant to A and A∗ , i. e., on the perpendicular bisector of AA∗ . The same applies to B and B ∗ , C and C ∗ .

Fig. 1.9 Reflection in a point or in a straight line, rotation by 180○

The question is whether all perpendicular bisectors actually run through the center of rotation Z. Let Z be the intersection between the first two bisectors. Therefore, we can imagine Z as being connected to the straight line AB. The auxiliary triangle

12

An idealized world made of simple elements

ABZ can be rotated into the triangle A∗ B ∗ Z about the point Z. However, C is also fixed to AB, that is, the distance CZ does not change during the rotation. Thus, Z must also lie on the perpendicular bisector of C and C ∗ . This remains true for all respective point pairs on the congruent figures. ⊙

If the figure f is rotated by 180○ about the center Z, it becomes a directly congruent figure f ∗ and can equally be seen as the reflection of f . Point reflections in the plane are, therefore, directly oriented. Reflections at a straight line, on the other hand, are reversely oriented (Fig. 1.9).

Similar figures, twisted into each other

The leaves of this plant are arranged in such a way that there are always two opposite leaves at each stem node. The next pair of leaves is then rotated by 90○ ; at the same time the size of the leaves is scaled. The scaling factor differs from node to node. Fig. 1.10

Fig. 1.10 shows an example which at first glance seems to be a spatial exercise: How are the leaves of the plant distributed along the stem? In this simple case, the leaves lie in parallel planes perpendicular to the stem. Two leaves of equal size are always in the same parallel plane, opposite to each other (rotation of about 180○ ). The next pair of leaves is of a different size and is rotated by about 90○ . The change in size is worth looking at in more detail (see Chapter 13).

1.2 Special points inside the triangle

13

1.2 Special points inside the triangle Every “real” triangle (A, B, and C do not lie on a straight line) possesses an orthocenter, a centroid, and a circumcenter. This may be familiar to most people, but it is not at all trivial to prove. The circumcenter U is the easiest to see.

A circle through three points – the circumcenter A circle can be defined by three points. To put it differently: Every triangle possesses a circumcircle. Proof : Let us first construct the center of the circumcircle as the intersection of two perpendicular bisectors: The locus of all points that are equidistant to A and B is a straight line perpendicular to AB at the midpoint MAB of the line segment AB. Furthermore, the locus of all points that are equidistant to B and C is a straight line that is perpendicular to BC at the midpoint MBC of the line segment BC. Both perpendicular bisectors intersect at U . Now we have U A = U B, and also U B = U C, from which we can conclude U A = U C. This means that the third perpendicular bisector must also pass through U . Consequently, U is the center of the circle through A, B, and C. ⊙

The centroid: a point of physical significance Centroids (or barycenters) play a significant role in physics, as they simplify many considerations. The existence of an unambiguous centroid S in a triangle is not trivial to prove. A vector-based proof for its existence can be found in [9]. Its construction, on the other hand, is very simple: One merely needs to connect the vertices of the triangle to the midpoints of the opposite sides and intersect these so-called medians. ⊕ Remark : The term centroid has its roots in physics. There, a distinction is made between vertex centroids, edge centroids, and volume centroids. For arbitrary figures or polygons, these centroids are not identical [9]. For triangles, edge centroids and volume centroids coincide, and for polygons with central symmetry, all centroids coincide. This is why it is so useful to work with triangles for technical applications. In three-dimensional space, these extraordinary properties are inherited by tetrahedra or polyhedra with central symmetry. ⊕

The orthocenter: a point of geometric significance

The altitude of a triangle is the straight line that is orthogonal to a triangle side and passes through the opposite vertex. The following observation is important for many later considerations and – once again – not at all trivial: All three altitudes of a triangle pass through a single point, the orthocenter.

14

An idealized world made of simple elements

Fig. 1.11 Circumcenter, centroid, orthocenter, Euler line

Proof : Let us consider Fig. 1.11 on the left: The midpoints of the triangle sides form the medial triangle that is similar to the original triangle, because all of its sides are parallel to the respective sides of the original triangle. The perpendicular bisectors of the original triangle intersect at a single point, as we have already proven, but they can also be interpreted as the altitudes of the newly created medial triangle, because they are (according to the definition of an “altitude”) perpendicular to their triangle side and pass through the opposite vertex. ⊙

This proof is not only elegant but gives us a further advantage: it immediately implies the existence of the Euler line. (This is precisely what we mean when we say that synthetic proofs are more useful than the purely analytical ones.)

All three points are guaranteed to lie on a straight line Fig. 1.11 on the left shows that the side lengths of the original triangle ABC relate to the resulting pink medial triangle MAB MBC MCA at a ratio of 2 ∶ 1. What is more, as the respective vertices lie on rays through a fixed center – the centroid S – they can be transferred into each other by means of central similarity. Given this central similarity, the orthocenter H of the big triangle (the anti-complementary triangle) is transformed into the orthocenter of the medial triangle, which, in turn, is also the circumcenter U of the original triangle. The straight line through the center S that connects H and U is the Euler line. Furthermore, we have HS ∶ SU = 2 ∶ 1.

The incenter – or: a circle on three tangents The question about a circle that touches all three triangle sides leads us to the incircle. Its center is determined by the intersection of at least two angle bisectors. Each circle that touches two straight lines has to be centered on such a bisector. If, for instance, we have intersected the angle bisectors through A and B, then we have found the center of a circle that touches both AC and AB, but also BC and BA, and thus, all three sides. Its midpoint must, therefore, also belong to a third angle bisector – this means that all bisectors pass through a single point. Thus, three straight lines (tangents) can define a circle unless they pass through a single point. However, this is not unambiguous: we have ignored

1.2 Special points inside the triangle

15

Fig. 1.12 Incircle center, three excenters

that there always exists a pair of angle bisectors that forms a right angle. How many points do these three pairs define? Once again, it is possible to use just two pairs for construction (the third pair provides no new solution). All in all, there exist four solutions to this construction, namely, the incircle and the three excircles. The question of finding a circle tangent to the side lines of a triangle is, thus, ambiguous. At least there exists a “finite number” of solutions! By the way: in general, neither the incenter nor the centers of the excircles (the excenters) lie on the Euler line.

Two ways of defining a circle are still missing . . .

Fig. 1.13 Secant and tangent of a circle . . .

The following theorem is useful for some circle constructions:

16

An idealized world made of simple elements

For all secants of a circle through a fixed point P , the product of the distance of P to the intersection points remains constant. This is called the power of the point with regard to the circle.

Fig. 1.14 The power of a point

Proof : We use the notations of Fig. 1.14. According to Pythagoras, the following is true: m2 +(r2 −x2 ) = d2 , or m2 − x2 = d2 − r2 = constant. However, m2 −x2 = (m+x)⋅(m−x) is exactly the product of the distances to the intersections (the power). If P lies outside the circle, there exist touching secants whose intersection points move together. In such cases, the product of the distances becomes the square of the tangent distance. ⊙

▸▸▸ Two nontrivial circle constructions Find a circle k that passes through two points P1 and P2 and furthermore touches a straight line t, or alternatively, a circle k that passes through a point P and touches two given straight lines t1 and t2 . Solution: Let us start with the first task (Fig. 1.15): We intersect the line P1 P2 of the given √ points with the given tangent t (Fig. 1.15) and determine the power ZP1 ⋅ ZP2 of the intersection Z, which can easily be constructed using Thales’s theorem. We have now found the contact point T on t. The desired center of the circle lies on t’s normal at the contact point T and the perpendicular bisector of P1 and P2 . We should not overlook the second solution: The tangent section can be determined on both sides.

Fig. 1.15 2 points + 1 tangent

Fig. 1.16 1 point + 2 tangents

1.2 Special points inside the triangle

17

Now for the second problem (Fig. 1.16): The locus of the centers of all circles that touch both tangents t1 and t2 is the pair of angle bisectors (Fig. 1.16). The solution circles lie in the same sector as P that is formed by t1 and t2 . Consequently, the centers lie on one particular “half-line”. Let us draw an arbitrary circle k touching t1 and t2 , with the center M located on this halfline. Relative to Z, it is similar to the touching circles. The point P is thus related, due to similarity, to two possible points P1 or P2 at the intersection of k with the ray ZP . The rays M P1 and M P2 are transformed into the parallel rays M2 P and M1 P . M1 and M2 are the desired centers of the two solutions k1 and k2 . ◂◂◂ If you have gained an appetite for more oddities related to triangles and circles, you are invited to ponder over three additional but no less intriguing theorems by Feuerbach, Kiepert, and Morley. You may also jump forward to the next section, where we will leave the drawing plane for a short excursion into Euclidean space in order to explain how these topics apply in three dimensions.

A circle through nine (!) points in the triangle If we look at the triangle ABC, we may notice that the centroid S subdivides the medians at a ratio of 2 ∶ 1. According to our knowledge about the points on the Euler line, the ratio SU ∶ SH = 1 ∶ 2 holds for the orthocenter H, the centroid S, and the circumcenter U of a triangle ABC. If we reflect the triangle at S and shrink it at a ratio of 1 ∶ 2, we get a directly congruent triangle A2 B2 C2 , the vertices of which are the midpoints of the triangle sides (Fig. 1.17). If we also transform the circumcircle, we get a circle k that passes through the midpoints of the triangle edges. The circumcenter U corresponds to the midpoint U2 = F of the smaller circle. With F S = s, we have SU = 2s, F U = 3s, and HU = 6s. Thus, F is the midpoint of the line segment HU . Given these circumstances, Feuerbach had the following brilliant idea: shrinking the circumcircle from the orthocenter H at ratio 1 ∶ 2 (without reflection) results in the same circle k, because U travels towards F . After this type of shrinking, the original triangle ABC corresponds to a triangle A3 B3 C3 of half the size. The circle k contains these points as well. The triangles A3 B3 C3 and A2 B2 C2 are congruent due to the same scaling factors and have mutually parallel sides. The six points are, thus, not arbitrarily distributed on the circle, but they are mutually opposite to each other. Now we still want to show that the foot of each altitude A1 , B1 , and C1 of the triangle ABC lies precisely on k: By definition AA1 ⊥ BC and thus A1 A3 ⊥ A1 A2 , which means that k is Thales’s circle over A3 A2 and thus A1 also lies on k. The analogue is true for B1 and C1 . Thus, we have found no fewer than nine points on the circle! For the purpose of illustration: Combinatorics tells us that if we pick any 9 points, 3

18

An idealized world made of simple elements

Fig. 1.17 Nine-point circle through the foot of each altitude, the side bisectors, and the vertices of the medial triangle

from this set can be combined into circles in (9 ⋅ 8 ⋅ 7)/(3 ⋅ 2 ⋅ 1) = 84 different ways.

The beer mat method From the proof above, the following remarkable addition can be derived (as an “encore”, so to speak): If we scale the nine-point circle k from C by the factor 2, the bisectors A2 and B2 pass over to A and B, as well as C3 into H. Therefore, there exists a circle that is congruent to the circumcircle and contains two vertices of the triangle as well as the orthocenter. This statement is true for all triangle points. So, the next time you find yourself waiting for your meal at a restaurant, with three circular beer mats within your reach, mark three points ABC at the edges of a single beer mat (which then becomes the circumcircle) and position the other two mats so that they contain two of these points each. The remaining intersection of the two beer mats is the orthocenter.

A point of high importance Let us now imagine, as in Fig. 1.18, that we have drilled three tiny holes into a disk through which we have pulled three strings of equal length that are tied together at the end G. (The triangle that is formed by the holes must not have an angle greater than 120○ .) To the other ends of the strings, we attach three equal weights. The weights will immediately stretch the strings to form angles of 120○ : the three equal forces are then in equilibrium. In sum, the system tries to place the weights at the lowest possible location. With a given string length d and the distances x, y, and z of the point G

1.2 Special points inside the triangle

19

from the triangle points A, B, and C. The weights hang at depths d − x, d − y, and d − z. The sum of these depths is, therefore, 3d − (x + y + z). If the weights have to hang as low as possible, then the expression x + y + z must be a minimum. It is also possible to define G as the point where the sum of distances to the triangle vertices is minimal.

Fig. 1.18 Fermat point

The point G is ascribed to both Fermat and Steiner . It can be constructed by intersecting the two circles or by intersecting at least two circles of circumference or, much more simply, by extending every triangle side outwards into equilateral triangles and connecting the new points X, Y , and Z with the opposite triangle points A, B, and C: The circumcircle of the triangle ABZ is the circle of circumference of the segment AB, from whose points the segment on the side of Z is visible at 60○ , and the segment on the side G at the supplementary angle of 180○ − 60○ = 120○ . In this special case, it should be obvious that the three lines actually intersect at a point: If a point G is found as the intersection of two lines, then two triangle sides can be seen under 120○ from G – and the third triangle side must automatically be 120○ , since the sum of these angles must add up to 360○ . Let us now discuss a generalization of this method.

How can an arbitrary triangle be converted into an equilateral triangle? Two triangles ABC and XY Z are perspective to a point if the connecting straight lines AX, BY , and CZ pass through one point. A theorem that can be traced back to Kiepert now states the following (Fig. 1.19, without proof): Kiepert’s theorem: If isosceles triangles are constructed above the sides of an arbitrary triangle ABC and they each share a common base angle ϕ, then the new vertices XY Z form a triangle that is perspective to the original triangle. For ϕ = 30○ , XY Z is an isosceles triangle.

20

An idealized world made of simple elements

Fig. 1.19 Kiepert triangle and Escher lizard

▸▸▸ An inventive tessellation

Fig. 1.20 Tessellation using the Escher lizard

A plane can be “tessellated” using equilateral triangles. If one shapes the originating tiles in a particularly ingenious fashion – as M.C. Escher certainly did – and uses them to fill the figure in Fig. 1.19, one gets a remarkably nontrivial tessellation, as in Fig. 1.20. More information on tessellation will be provided in Chapter 12. ◂◂◂

Are there other methods to convert an arbitrary triangle into an equilateral triangle? Triangle geometry is an extremely “mature” discipline of science. To make a sensational discovery in this field in our day and age would come close to a miracle. In the year 1904, the American mathematician Frank Morley discovered the following: a theorem whose aesthetics recalls the elegant proofs in Euclid’s Elements – despite the fact that the theorem is not fundamentally geometrical, as we shall see soon. Morley’s theorem: If the interior angles of an arbitrary triangle are trisected, the intersections of the trisecting straight lines that are adjacent to the triangle sides form an equilateral triangle. Proof : The proof that follows originates, in essence, from D.J. Newman (1996). We shall put the cart before the horse, so to speak, and begin with the result – an equilateral triangle XY Z with side length 1. We then measure off, as in 1.21,

21

1.2 Special points inside the triangle

4π . The resulting 3 ∗ auxiliary triangles should not overlap. If we can show that s = s and t = t∗ , then we are almost done, because by this “relabeling”, we obtain equality for the remaining angles. First, we show that s + t = s∗ + t∗ .

the angles u, v, and w twice each. We require that u + v + w =

Fig. 1.21 Morley’s theorem

2π This is a result of s = π − u − w, t = π − u − v ⇒ s + t = 3 π 2π and s∗ + t∗ = π − (2π − − (v + w)) = − u. 3 3 Moreover, by applying the law of sines in the triangles XZB and XY C, we obtain 1 d 1 e sin s e = , = ⇒ = , sin s sin u sin t sin u sin t d and by applying the law of sines in BCX, we get d e sin s∗ e = ⇒ = . sin t∗ sin s∗ sin t∗ d We may now conclude (because the sine function is monotonic) that s + t = s ∗ + t∗ ∧

sin s∗ sin s = ⇒ s = s ∗ ∧ t = t∗ . sin t∗ sin t

⊙

22

An idealized world made of simple elements

The dilemma of angle trisection As we have already mentioned, Morley’s theorem is not fundamentally geometrical. This means that it cannot be verified or “replicated” by compass and ruler alone. Why do such approaches fail? The task requires the division of an arbitrary angle into three equal parts. From a mathematical standpoint, this involves the solution of an algebraic equation of three. Despite our best efforts, our compass and ruler are not enough to provide a solution. And yet, the problem seems so simple! How would you trisect an angle? With a set square and some quick mental arithmetic? Archimedes provided a solution that requires some constructional agility but allows us to find a mathematically correct solution:

Fig. 1.22 Trisection according to Archimedes

Let α be an angle (Fig. 1.22) through an isosceles triangle AM B. Let us draw an auxiliary circle k (radius r = AM ) around M . Now we can mark two points P and Q on our ruler at a distance r and move the ruler in such a way that P moves along the elongated triangle leg AM and Q moves on the circle k. If the elongation of P Q passes through B, then the section M Q encompasses, along with the triangle leg AM , an angle of ϕ = α/3.

Proof : The proof of Archimedes is as ingenious as it is simple: We recognize two isosceles triangles M BQ and P QM (the equilateral legs have length r). From ϕ = ∢P M Q it follows that ∢M P Q = ϕ. The angle ∢M QB is twice as large (2ϕ) because the third angle in the triangle P M Q measures 180○ − ϕ − ϕ. This also means that ∢M BQ = 2ϕ, and furthermore that ∢P M B = 180○ − ϕ − 2ϕ. The supplementary angle α is, therefore, 3ϕ. ⊙

However, can this be considered a simple compass-and-ruler-based solution? Well, it is not as flawless as it may appear: Our meticulous fitting of the ruler is not a precise construction but rather a matter of “trial and error”. Let us try to be more precise and draw all positions of the ruler that pass through B. We now get a so-called pencil of rays. Each ray possesses an intersection Q with the circle k. From there, we can determine a point P at distance r. If

1.2 Special points inside the triangle

23

P lies on the elongation of AM , we were successful. What, then, is the locus of all points P ? If the locus were a circle or an arbitrary conic section, then everything would be simple enough – the intersection of a conic section and a straight line can be determined with the help of ruler and compass. Alas: the curve is of a higher degree – namely, it is a so-called conchoid, here a limaçon (Fig. 1.23, left).

Fig. 1.23 A limaçon and an astroid

Let us give it a second try: Let us choose P on the elongated leg AM . We then determine a point P on k at distance r (this yields two symmetrical solutions) and we get Q. In the general case, the elongation P Q does not intersect k at B, but we can try this many times. This leads to P Q enveloping a curve. The right solution is the tangent from B to this. Yet, maybe this curve is “simple”? No such luck! This time, it is a so-called astroid (Fig. 1.23, right), which is also of a higher degree. Many a courageous mathematician has “bloodied his nose” on angle trisection – despite the fact that it has long been proven that there can be no solution by ruler and compass.

Points at infinity Points can be infinitely far away. In such cases, mathematicians speak of points at infinity. (Should you find it difficult to imagine this concept, try imagining a distance of something like a light year, which, for all modest purposes, amounts to roughly the same thing.) Points at infinity are often labeled by the subscript u: Thus, Pu is, if not otherwise stated, a point at infinity. This may sound simpler than it is: We shall soon discover the mental stumbling blocks and geometrical advantages that it implies. Every straight line has a point at infinity. But why only one and not two? Is it not true that straight lines proceed towards infinity in two directions? Are these two, by any chance, the same point? Can two points on a straight

24

An idealized world made of simple elements

line be identical if one of the points is located one light year away in one direction and the other is another light year away in the opposite direction? Let us take some time and remember the following simple statement: • Two different straight lines in the plane always possess an intersection.

Fig. 1.24 Parallel lines intersect, by definition, exactly once – but only “at infinity”!

If we do not allow for points at infinity, we must immediately make an exception: Two straight lines in the plane always possess an intersection, provided that they are not parallel. If, on the other hand, we decide to be pragmatic and allow for points at infinity, we can state the following: Two parallel straight lines share one point at infinity (and not two, otherwise we would once again encounter an exception). We shall soon discover that there is a very reasonable explanation for this if we look at the problem “from a higher perspective”. For now, let us remember: • A point at infinity is determined by the direction of the straight line. Parallel straight lines determine the same point at infinity. This whole issue appears much simpler when considered “from a higher perspective”. Yet, in order to do this, we need to know more about planes, which are discussed in the next section.

1.3 Elementary building blocks in space

25

1.3 Elementary building blocks in space Let us now venture from the drawing plane into three-dimensional space. This is not a dangerous step, because our bodies naturally occupy threedimensional space. Our spatial imagination will permit us to comprehend the necessary trains of thought. In space, points remain “infinitely small”, having no extent whatsoever. But this is more of a philosophical statement. The stars of our universe could hardly be called infinitely small; on a photo from a great distance, however, they appear as points. Speaking of which: what appear to be stars in Fig. 1.25 are the relics of fireworks in the sky on New Year’s Eve . . .

Fig. 1.25 “Points” and “straight lines” in space

Points may, once again, be located at infinity, and the familiar u in the subscript is used for their notation. We will soon explain the mental difficulties, as well as the advantages, of this type of thinking. In the drawing plane, an infinite number of points results – if arranged in a certain way – in an infinitely thin and infinitely long one-dimensional straight line. We can also say that a straight line is “generated” by the translation of a point. Straight lines should be thought of as unbounded: Every line segment P Q possesses an infinitely long straight carrier line g = P Q. In space, however, we are still missing a third basic element:

Surfaces without curvature In everyday speech, “plane” describes something horizontal: The High Plane of Tibet, the Pannonian Plane, etc. Sloped, uncurved surfaces are commonly referred to as “sloping sites,” but not so in geometry: A plane is formed when we array an infinite number of parallel straight lines along another straight line. It can be said that a plane is “generated” by the translation of a straight line along another straight line. The generating straight line and the directional straight line of the translation both “generate the plane.”

26

An idealized world made of simple elements

Fig. 1.26 A “plane” . . .

Fig. 1.27 . . . and a “sloped plane” in colloquial speech

In Europe, planes are denoted by lowercase Greek letters, such as α, β, ε, ϕ, etc. This sometimes leads to problems with the notation of angles, which are usually also named in this manner. For example: image planes are often called π, while having nothing to do with the circle circumference to diameter ratio π = 3.141592653589793 . . . It is, nevertheless, important to stick to this convention, since the alternative is even more confusing (many Greek capital letters, for instance, are identical to Latin capital letters, leading to planes being possibly mistaken for points). Let a be the generating straight line and b the straight line pointing in the direction of the translation. The straight lines a and b intersect at S = a ∩ b (read “a intersected with b”). The generated plane shall be called ε = ab (read “a joined with b”). Every straight line g that intersects a and b lies entirely in ε, since it intersects every parallel of a in ε. One can therefore write g ⊂ ε (read “g in ε”). Thus, an infinite number of straight lines lies in a plane. Each of these straight lines also implies a point at infinity. What, then, is the locus of all of these points? If we intersect all straight lines in the plane with another straight line u in the same plane that is “almost infinitely far away”, then all intersections lie on this straight line. Therefore, it makes sense to conclude: • All points at infinity of a plane lie on a straight line, the line at infinity of the plane. We now have the following theorem without exception:

1.3 Elementary building blocks in space

27

• Two different planes always have a straight line of intersection. Every plane stance, thus, defines a line at infinity, and since an infinite number of such orientations are possible in space, the following question arises: what is the locus of all lines at infinity? Now we know how to proceed in an analogous way: we intersect all planes of space with an “almost infinitely distant plane” ω and get an infinite number of almost infinitely distant straight lines that, by definition, lie in ω, which thus becomes the plane at infinity. Mysterious? Not at all! The next chapter deals with projections, and in it, we shall again consider planes at infinity, but from a higher position. What may seem confusing right now will by then seem completely normal. The following theorems should already be perfectly comprehensible to us: • A straight line g always shares an intersection point S with a plane ε. (If the straight line is located entirely in the plane, then every point on the straight line is an “intersection point.”) • Three different planes ε, ϕ, ψ always intersect in one point S = ε ∩ ϕ ∩ ψ. (If the point is a point at infinity, then the intersection lines of two planes are mutually parallel.) • If two parallel planes ε ∥ ϕ are intersected by a third arbitrary plane ψ, then both intersection lines of ψ are parallel. As a “proof,” the following could obviously be stated: The chain of evidence is as follows: The three planes ε, ϕ, ψ share a point at infinity. All intersecting lines of any two planes must pass through this point and must, therefore, be parallel. By the way: the third, not-soevident intersection line ε ∩ ϕ is the line at infinity of the planes.

28

An idealized world made of simple elements

1.4 Euclidean space We live in three-dimensional space and are, in general, more or less used to three-dimensional thinking. We call this space the “space of perception.” Distances and angles are of great importance to us. A sheet of paper can be seen as the two-dimensional subspace of the space of perception. We are particularly familiar with geometry in two dimensions, as it is easy to – literally and figuratively – keep an “overview” of its limited boundaries. However, if the sheet of paper takes on astronomical proportions, it becomes more complicated. After all, we are located on the globe, on a surface on which straight lines do not even exist. Perfectly straight lines do not exist in nature either. From physics we know that not even light travels in perfectly straight directions: It is diverted by the mass of the stars and star systems in whose vicinity it passes. The term gravitational lensing is used to describe this phenomenon. However, let us stay “on Earth”, just like Euclid , one of the greatest thinkers in history. More than 2, 300 years ago, he operated a school of mathematics in Alexandria and condensed, in his 13-chapter Elements (which are treated as separate “books”), the entire mathematical and geometric knowledge of his time. The Elements survived the turmoils of history (including two fires at the Library of Alexandria) and were later translated – from Arabic into Latin – and published in Europe, where they have henceforth formed the basis for geometry right up until the 19th century.

Basic terms and axioms First of all, Euclid defined two basic terms, namely, “points” and “straight lines,” which can be put into geometrical relations by means of words like “lie on,” “between,” “congruent,” etc. He then defined the so-called axioms of geometry: sensible, immediately obvious, and non-contradictory rules that can be assumed but cannot be proven, such as: “For two points, there exists exactly one straight line on which they both lie,” or “Of three points on a straight line, there is always one that lies between two others.” Now he defines new entities (circles, etc.) about which assertions can be made, and all of these assertions can be proven entirely by logical combinations of the aforementioned axioms. Thus, gradually, one brick is laid upon the other. It is essential that all definitions and proofs are based on secure knowledge that can be traced back to the axioms. This method was groundbreaking for its day – moreover, it made it possible to verify the existing empirical rules and procedures of the Egyptians and the Babylonians. Some of these rules could actually be proven and were, thus, promoted to “theorems,” while others were, nevertheless, determined to be useful approximations.

29

1.4 Euclidean space

A pillar of little support One of Euclid ’s axioms says that it is possible to draw a unique parallel to a straight line through a point outside of it. Mathematicians have been trying for many centuries to prove this axiom by means of others, thus promoting it to the status of a “theorem.” By the mid-19th century, it was proven that, while geometry is possible without this axiom, several well-known theorems would have to be discarded. In the last section, we will learn more about non-Euclidean geometry. This particular axiom of parallels is problematic when considering the number of points at infinity of a straight line: If we do not want to accept that there exists only one point at infinity for each direction of a straight line, then much of space of perception geometry must inevitably collapse.

The sum of distances

Fig. 1.28 Distance circle

Fig. 1.29 String construction of an ellipse

If we look for all points P in the plane that are at given distances d1 and d2 from points F1 and F2 , then we must intersect the circles k1 (F1 ; d1 ) and k2 (F2 ; d2 ). As we know, this yields (in general) two solutions, or no (real) solution. If the circles merely touch, we speak of a double solution. Thus, we can construct an ellipse as the locus of all those points P whose sum of distances from two fixed points F1 and F2 is constant (= 2a). The principal vertices A and B of the curve are found when the distance circles touch each other. The auxiliary vertices C and D can be found when both radii equal a. F1 and F2 are called focal points of the ellipse. For the hyperbola, the difference of the distances from two fixed points is constant. You can find out more about conic sections in Chapter 5.

The Apollonian circles The search for all points P whose distances from two fixed points F1 and F2 form a constant ratio lead to the Apollonian circles. If this ratio is 1 ∶ 1, the circle “degenerates” into the perpendicular bisector. A straight line could, thus, be interpreted as a circle with an “infinitely large radius” and “a center at infinity.” The perpendicular bisector is the set of points that is equidistant to two given points. While this may be obvious, Apollonius’s more complex assertion needs to be proven. For this purpose, a “full-blooded mathematician” would draw a

30

An idealized world made of simple elements

Fig. 1.30 Apollonian circles

Fig. 1.31 Pair of angle bisectors

coordinate system that is defined by the following fixed points: Let F1 (0, 0) be the point of origin and F2 (d, 0) a position on the abscissa. The condition for a point of the plane P (x, y) is then as follows: √ √ P F1 ∶ P F2 = x2 + y 2 ∶ (x − d)2 + y 2 = c = constant. By squaring the equation and proceeding with a slight rearrangement of the terms, one gets the equation of a circle with the midpoint on the x-axis. This solution may be elegant but it would have been entirely unknown to Apollonius of Perga (born in Asia Minor 262 B.C., died in Alexandria 190 B.C.). Let us not forget that Apollonius not only proved this theorem but also authored eight tomes of fundamental work on the “geometry of positions,” which deal with conic sections (Conica) in particular. He first considered the following theorem: The angle bisectors of a triangle divide the opposite side in the ratio of the adjacent sides. Proof : The theorem is immediately obvious, given an appropriate sketch (Fig. 1.31). The two angle bisectors C form a right angle because they subdivide the angle γ and the supplementary angle 180○ − γ, and therefore γ/2 + (180○ − γ)/2 = 90○ . Let us now draw the parallel p through a triangle vertex B towards the inner bisector that is simultaneously orthogonal to the outer bisector. The straight line p intersects the extension of AC in a point B ∗ , and the triangle BCB ∗ is isosceles. On the side AC, CA = b, and CB ∗ = a. By means of the inner angle bisector and p, this affine ratio is transferred onto AB according to the theorem of intersecting lines: AT1 ∶ T1 B = b ∶ a. The point B ∗ thus arrives at B while the point C at the division point T1 on the inner angle bisector A remains fixed. According to the theorem of intersecting lines, the following is, indeed, true: AT1 ∶ T1 B = b ∶ a. ⊙

Harmonic points

The exterior angle bisector divides the line segment by analogous reasoning but with an inverted sign: AT2 ∶ BT2 = b ∶ a or AT2 ∶ T2 B = b ∶ (−a).

31

1.4 Euclidean space

The pair (A, B) is said to separate the pair (T1 , T2 ) harmonically. Harmonic pairs of points play a fundamental role in projective geometry, which is the subject of a later chapter. However, let us return to Apollonius. The theorem that involved the angle bisectors might also have been proven by means of the sine law [9], of which he was probably aware – but this was not necessary, as he proceeded in his preferred way of “elementary geometry.”

Fig. 1.32 Proof of Apollonius

We are getting really close to the circle of Apollonius (Fig. 1.32): We have the triangle ABP and both angle bisectors that cut out the division points T1 and T2 from AB, the position of which is exclusively dependent on the ratio a ∶ b. The right angle that is formed by both angle bisectors almost “cries out” for Thales’s theorem: C lies on the Thales circle above T1 T2 . Now we shall change the triangle in such a way that a ∶ b remains constant. Thus, T1 and T2 also remain constant, and the Thales circle, likewise, remains fixed. C moves on the Thales circle, which we may now call the circle of Apollonius.

All that remains is the product Next to the ellipse (constant sum of distances to two fixed points) and the hyperbola (absolute value of the difference of the distances is constant), Apollonius also managed to fit the circles (constant quotient) into this scheme. He presumably also tried to attain useful results from the product of the distances, but they simply do not yield such “beautiful” results (they are fourthorder curves, which would have caused problems for the ancient Greeks, as there were no computers that help us to make sense of them nowadays). If the product of the distances to two fixed points F1 and F2 should be constant for the points P , we are dealing with a so-called Cassini oval , which we will encounter again when discussing the intersections of a torus (Fig. 6.80).

From the plane into three-dimensional space All prior reflections about distances are equally applicable in space if we rotate the locus curves about the axis F1 F2 . Circles, the centers of which lie on the axis, turn into spheres. At their limiting cases (infinite radii), the planes appear orthogonal to the axis by rotation.

32

An idealized world made of simple elements

Fig. 1.33 Cassini’s curves, defined as the locus Fig. 1.34 . . . and a stunning similarity to the of all points with a constant product of the dis- cross-section of a pine tree trunk. Consider also tances from two fixed points . . . Fig. 1.8, right.

During the rotation, the intersection points of two such circles move in planes perpendicular to the axis. Ellipses trace ellipsoids, and arbitrary curves generate arbitrary surfaces of revolution. We will discuss these surfaces in great detail.

Analogies on the sphere The equivalent solutions on the sphere are equally interesting. For instance, let us ask for the points on the Earth’s surface that are equidistant from two fixed points: we then have to intersect two circles on the sphere. An analogous ellipse construction leads to a spherical conic section. For all points P on such a curve, the sum of minimal (spherical) distances from F1 over P to F2 is equal.

Other distance lines and distance surfaces Apart from circles and spheres, there exist other important distance lines and distance surfaces. What does the curve of points P in the plane look like if they have a fixed orthogonal distance d from a straight line f in this plane? This question yields a parallel pair of straight lines. By means of rotation of this object about the axis f , we get a cylinder of revolution with radius d, whereas the translation yields a distance plane to the given plane ϕ through f .

Fig. 1.35 Parallel pair and cylinder

Fig. 1.36 Angle bisector and cone

Given two fixed non-parallel straight lines f1 and f2 in the plane, we are looking for all points P that have the same orthogonal distance to both

1.4 Euclidean space

33

lines. A pair w1 , w2 of angle bisectors can be found. The two angle bisectors w1 and w2 are always perpendicular: Let α = ∢f1 f2 be the mutual angle of both given straight lines. Since these are not oriented, one could also have measured β = 180○ − α (the supplementary angle). For the angle ω = ∢w1 w2 , the following is true: ω = α/2 + β/2 = α/2 + (180○ − α)/2 = 90○ . In this case, a rotation about an axis does not result in an analogous theorem in spatial geometry. Nevertheless: If we rotate about one of the bisectors, such as w1 , the straight lines f1 and f2 will lie on the same cone of revolution. The circle P that touches both straight lines becomes an inscribed sphere that touches the cone, and the rays through the contact points form an additional cone of revolution that intersects the first cone perpendicularly along a circle. The translation of the planar situation in the direction of the normal to the carrier plane is much more interesting. It yields a pair of angle bisector planes, on which all points are located that are equidistant to two given planes. We can conclude that it is often possible to derive spatial analogies from two-dimensional situations.

34

An idealized world made of simple elements

1.5 Polarity, duality and inversion Infinity can mean many things Until now, we have used the term dimension many times. A point, for instance, is zero-dimensional – it has no extention. A straight line is onedimensional – with an extention in precisely one direction. A plane is twodimensional. It can be seen as both a collection of points and a collection of straight lines. Let us attempt a comparison: are there more points or straight lines in a plane? The question may strike you as somewhat insane. First of all: why should we even want to find out? Secondly: it should be obvious that a plane contains an infinite number of points, as well as an infinite number of straight lines. Whatever could we hope to differentiate with a term like infinity? The answer to this question leads to unexpected connections. Pondering such supposed absurdities is, indeed, worthwhile.

A close relationship We define the following geometrical operations in the plane that we shall call polarity with regard to the circle:

Fig. 1.37 Polarity in the plane

Let us choose an arbitrary but fixed circle k with the midpoint M (Fig. 1.37). If a point P lies outside this circle, then we have two tangents at k that touch k at two points, Q and R. The connecting straight line p = QR is assigned to the point P : P ↦ p. It is perpendicular to the line M P : p ⊥ M P . The inverse mapping is also unambiguous: If an arbitrary straight line p intersects the circle at the points Q and R, then we can define tangents through these points that intersect at a point P : p ↦ P . Once again, M P ⊥ p applies. The assignment p ↔ P is, thus, invertible, and we speak of pole P and polar p. Even points at infinity are captured: Their polars are the diameters of k.

1.5 Polarity, duality and inversion

35

The case of P lying on the circle k poses no additional difficulties. In such cases, p is the tangent of k in P . If P lies inside k, we define its polar as follows: We draw an auxiliary straight line p∗ ⊥ M P through P , whose pole P ∗ is the foot of the normal of the straight line p from M that is to be determined. In the reverse case, if p passes through k, we determine the foot of the normal P ∗ of M on p, whose polar p∗ intersects M P ∗ in the pole P . Even the line at infinity of the plane can be determined in this way: It is equal to the center M of the circle. Therefore, the polarity of the circle consistently guarantees the unambiguous relationship between points and straight lines in the plane, from which it follows that the plane contains precisely as many points as straight lines. It is, therefore, correct to speak of the plane as a two-dimensional point space as well as a two-dimensional line space. These two spaces are mutually dual spaces. This circumstance can be further illuminated mathematically: The definition of a point in the plane requires two numbers (the x-coordinate and the ycoordinate). The same is true for the definition of a straight line (e. g., the y-value on the y-axis and the slope angle). Let us, once again, attempt to derive a spatial analogy (Fig. 1.38). If we rotate our plane about the axis M P , then the circle k generates the sphere κ, the tangent on the circle becomes a cone of revolution, the contact points Q and R become contact circles of the cone and κ, and their carrier plane is the polar plane π of the point P . The assignment π ↦ P works in the same way. The polarity with respect to the sphere κ, once again, guarantees the consistent assignment between points and planes of space (as for the plane at infinity, it is the midpoint of the sphere). We can, thus, conclude that space contains as many points as it contains planes.

Fig. 1.38 Polarity in space

Thus, Euclidean space can be interpreted as both a three-dimensional point space as well as a three-dimensional plane space. Both spaces are mutually dual spaces. ⊕ Remark : Mathematically speaking, a point in space is defined by three numbers (e. g., through its Cartesian coordinates). The same is true for a plane (which is,

36

An idealized world made of simple elements

e. g., determined by the normal distance from the origin and the inclination angles with respect to the xy-plane and the xz-plane). ⊕

Back to the two-dimensional case: If r is the radius of the circle, then we have a simple relation between the pole P and its polar p ∋ P ∗ according to Euclid’s theorem (Fig. 1.37): M P ⋅ M p = r2 . With this, we can prove the following theorem: If a point A in the plane moves on a straight line b (Fig. 1.39), then its polar a traverses a pencil of straight lines about the pole B of b. The assignment pole↔polar is, thus, invertible, and pencils correspond to ranges of points, and vice versa.

Fig. 1.39 The proof

Fig. 1.40 The anti-inverse point

Proof : Let B be a pole and b ∋ B ∗ its polar (Fig. 1.39); then it follows that M B = r2 /M b. Further, let A be a point on b. For its polar a ∋ A∗ , M A = r2 /M a. a intersects the ray M B at the distance x. The triangles M BA∗ and M AB ∗ are similar; it is also true that M A ∶ M B ∗ = x ∶ M a ⇒ x = r2 /M B ∗ = M B.

⊙ ⊕ Remark : The construction of polars of a point with respect to a circle so far involves tangents of circles. We have to differentiate between points inside and outside the circle. There exists a very simple substitute construction that always works: As in Fig. 1.40, simply construct a right-angle hook, that yields a point Pa that is “anti-inverse” to P . According to the altitude theorem, M P ⋅ M Pa = r2 . Therefore, the point only needs to be reflected at the center of the circle in order to lie on the polar. ⊕

It appears that while making the leap from the plane into space, we have somehow lost track of straight lines; so, let us catch up on that. A straight

37

1.5 Polarity, duality and inversion

line g in space can be interpreted as the connection of two points A and B (Fig. 1.38 on the right). The polar planes α and β correspond to these points. Let us now consider the intersection line g ∗ = α ∩ β. If we are able to show that a polar plane γ through g ∗ (γ ⊃ g ∗ ) can, indeed, be assigned to every point C on g, then it makes sense to define g and g ∗ as polars. In that case, straight lines correspond to straight lines, and therefore, line space is self-dual! Proof : Let us interpret the planar situation spatially. The circle can then be interpreted as a sphere contour. The line g = AB lies in the image plane, the corresponding polar planes α and β are then “projecting” – this means that they appear as straight lines. Their intersection line g ∗ is perpendicular to the image plane and appears as a point at the distance r2 /M g. This distance is equal for all points of g. Thus, the linearity of planar polarity is transferred into three-dimensional space! ⊙

T∗

t

c∗

T∗

t

P

c∗

P

c c k

k

Fig. 1.41 Polarization of a curve c at a circle k: The tangents t of c are transformed into the points T ∗ of the resulting curve c∗ . To the right: Conics (ellipses, parabolas, hyperbolas) are transformed into conics.

With polarization as our tool, we can transform not only points but entire curves (Fig. 1.41). When we polarize a curve c (as a set of points) at a circle k, the result is a curve c∗ that is enveloped by a set of tangents. We can also polarize the tangents of c and get the points of c∗ . The whole transformation is reversible. That is to say, if we polarize c∗ at k, the result is c. Remarkably, the simplest curve (of algebraic degree two), namely a conic, is transformed into another conic. Fig. 1.42 illustrates the polarization of a space curve at a sphere. The set of all tangents t of the curve c is transformed into the set of all tangents t∗ of a corresponding space curve c∗ . The process does, however, not transform the curve pointwise. In Chapter 7 we will discuss the depicted special case (c is a helix) .

38

An idealized world made of simple elements

t∗ P∗ c∗

c∗

c

P t

c Σ

Fig. 1.42 Polarization of a space curve c at a sphere Σ: The tangents t of c are transformed into the tangents t∗ of the resulting curve c∗ . Note that the contact points P and P ∗ only correspond indirectly to each other.

The principle of duality We now notice the following: By polarization with respect to a circle in the plane, the terms point and straight line are interchanged, as are the operations connect and intersect. Thus, if a theorem contains only such terms and operations, it can easily be converted into a correct dual theorem. Let us consider a simple example: • The connection of two points is a straight line ↔ The intersection of two straight lines is a point. The analogue is also possible in space: By polarization with respect to a sphere in space, the terms point and plane are interchanged, as are the operations connect and intersect. In this case, the term straight line remains unchanged. Thus, if a theorem of spatial geometry contains only such terms and operations, it can easily be converted into a correct dual theorem. Here are some simple examples that illustrate this: • The connection of two points is a straight line. ↔ The intersection of two planes is a straight line. • Three intersecting planes define a point. ↔ Three “connected” points define a plane. • If two straight lines lie in a plane, then they intersect at a point. ↔ If two straight lines intersect at a point, then they lie in a plane. The following theorem may not be as self-explanatory: • Space curves can be generated by a moving point as well as by a moving plane.

39

1.5 Polarity, duality and inversion

We will often use this theorem: It holds the key to the so-called developable surfaces, which play an increasingly important role in modern architecture.

An infinite amount and infinitely more Polarity has shown that space contains as many planes as it does points. From mathematics, we know that in a Cartesian coordinate system, every point can be described by three coordinates. This is why we speak of threedimensional space (which should, more accurately, be referred to as a point space), and for the same reason a three-dimensional plane space exists as a dual counterpart of point space. But is the line space also three-dimensional? Let us consider all straight lines determined by a fixed point P and an arbitrary point in a horizontal plane β (P ∈/ β) (Fig. 1.43). There exist as many lines as there are points in this plane, because any point in β can be joined with P . If we now move the vertex of the pencil P on an arbitrary straight line g ∥ β, we get the same number of connecting lines for each of the infinite positions of P . This number alone – of all straight lines that intersect g – is as large as the number of points in space! It would appear that there are many more straight lines in space than there are points.

P g∥β β

Fig. 1.43 Variation of the vertex of the pencil. Through each point P , there exist as many straight lines as there are points in the plane.

Now, the vertex of the pencil P should be able to vary all over the plane γ ∥ β. There, this point should have the two coordinates (u, v). The points in the base plane β also possess two-dimensional coordinates (x, y). Each choice of the four parameters (u, v, x, y) yields a new straight line that is not identical to any other. These parameters could be interpreted as coordinates in a fourdimensional coordinate system (however it may look: we are not capable of imagining it visually). We therefore say that line space is four-dimensional.

40

An idealized world made of simple elements

⊕ Remark : That may be easy to state, but it is quite something to consider that our space of perception should have many more straight lines than points and planes! Naturally, such an idea has consequences, and thus, we must not be surprised if, from a geometrical point of view, many things that involve straight lines require more effort. For instance, we will see that it is not at all easy to view an arbitrarily positioned straight line in such a way that it appears as a single point (in other words, that it is “projecting”). Moreover, if we want to imagine rotations about arbitrary axes, we have to be “geometrically trained,” and pretty well-trained at that. How simple it is, by comparison, to imagine a rotation about a vertical axis! It is all the more important to visualize complicated situations through specific points of view, which is the task of descriptive geometry. We call this the “reduction of dimension,” and the training of this skill is one of the highest goals of geometry education. ⊕ ⊕ Remark : In algebraic geometry, dimensions are counted by “degrees of freedom”: Three points in space define a plane. Each point in the plane has two degrees of freedom. Thus, the dimension of the plane space (considered as a space of points) can be calculated by 3 ⋅ 3 − 3 ⋅ 2 = 3. By analogy, two spatial points define a straight line where each point on the straight line possesses 1 degree of freedom. Thus, the dimension of the line space is 2 ⋅ 3 − 2 ⋅ 1 = 4. ⊕

Inversion – not every transformation is linear The polarity with respect to a circle (M ; r) in the plane defines a linear relation between points and straight lines on a plane. The pole P corresponds to the polar line p ∋ P ∗ where M P ⋅ M P ∗ = r2 . We can also assign the point P ∗ to the point P . This relation is called inversion or reflection in a circle. While this correlation is invertible, it is, intriguingly enough, no longer linear: When P moves in a straight line, P ∗ moves on a circle. The proof for this is mathematically easy to derive and can be found in [9]. Without going too much into detail (we will talk about it later): The inverse of an algebraic curve of degree n is (generally) a curve of degree 2n. The straight line is of degree one, the circle degree two. A conic section (usually) corresponds to a curve of degree four, etc. The inversion is, thus, called a quadratic transformation. An allegedly inexplicable “anomaly” One exception is particularly notable during inversion: a circle does not correspond, as we would expect, to a quartic curve, but once again to a circle – and if the circle contains the circle midpoint M , it corresponds to a straight line (the proof for this will be given on p. 225)! Such things are irritating at first: are we not dealing with a quadratic transformation after all? In order to explain this occurrence, we would have to make an adventurous “excursion” into a non-real world – but this would exceed the scope of this book. Rest assured, the supposed anomaly can be brought under mathematical control.

1.5 Polarity, duality and inversion

41

Fig. 1.44 Inversion in a circle, Peaucellier -Lipkin inverting linkage

A mechanism for the realization The fact that circles correspond to circles is not at all self-evident, but it can be used to construct a mechanism that automatically executes the inversion (Fig. 1.44). Here, it is justified to ask the question, “Why do I need this?” Let us explain: By using this inversion, a mechanism can be built that converts a pure rotation into an exact straight translation. This problem is not to be underestimated in the field of mechanics: a rotation is something very practical – every engine rotates a driveshaft in one form or another. Using the mechanism, a point is to be moved in a straight line without having to be directly guided on something like a straight track. A certain H. Hart solved this problem through inversion . . .

Spherical reflection The inversion can be performed equally well in three-dimensional space. The inversion circle is replaced by an inversion sphere (M ; r). The points P and P ∗ are, once again, linked via the relation M P ⋅ M P ∗ = r2 . P ∗ lies in the polar plane of P . The transformation P ↦ P ∗ is quadratic: Thus, planes are mapped to spheres (usually). The proof can be made by rotating the planar situation straight line ↦ circle about the normal of the straight line through the point M . Surfaces of degree n (see p. 169) are transformed into surfaces of degree 2n. Planes are also considered as spheres with “infinitely large radius” and a “center at infinity.” Spheres and planes are transformed into spheres or planes, i.e., “inversions preserve spheres”; see also Fig. 6.106).

42

Fig. 1.45 Reflection in a sphere

An idealized world made of simple elements

Fig. 1.46 Inversion of a rotational surface in a sphere

By analogy to circle reflection, we may, at this point, speak of reflection in a sphere. By the way, the physical reflection in a spherical mirror is, as a concept, very different from inversion: It transfers space onto the surface of a sphere. This means that three-dimensional space must be mapped onto a twodimensional surface, and this loss of dimension implies a simultaneous loss of information: the situation in space cannot be reconstructed from the image on the sphere. On the other hand, the inversion in the sphere is an invertible relation between points in space that does not cause a loss of information. Purism The ancient Greeks considered a problem to be “exactly solvable” if it could be constructed by compass and ruler. This is a justifiable demand for people without computers. For many centuries, however, it has been possible to exactly solve not only quadratic problems but also those of degree three and four – by a detour into complex algebra. All other methods are approximations at best, including the computer-assigned ones, even if they claim to be precise to 15 decimal places. It is possible to be stricter still. Which problems are only solvable by compass? It can be shown that every problem that is solvable by compass and ruler is also solvable by compass alone. Of course, the separate steps become more elaborate. The following example is said to have been devised according to a suggestion from Napoleon Bonaparte and is famous for this reason. The allegedly simple problem reads as follows: How can we find the center K of a given circle k without the assistance of a ruler? By compass and ruler, it can be solved in only a few seconds: One simply has to choose two arbitrary points A and B on the circle k and use them as centers to draw two circles a and b of equal size. The line joining the intersections of a and b has to pass through the center. By repeating the

1.5 Polarity, duality and inversion

43

Fig. 1.47 One of the most useful tools until the end of the 20th century

Fig. 1.48 Napoleon’s assignment, including instructions

construction with a third arbitrary point C instead of B, the final center can be found. It is, of course, the circumcenter of the triangle ABC. Without a ruler, it is not that much more difficult. Six circles are needed in order to find the midpoint – this is quite easy if you follow the instructions (Fig. 1.48). However, the proof for this is pretty elaborate; it requires many properties that we have come to know from inversion. ▸▸▸ A proof that isn’t: appearances can be deceiving . . . In this chapter, we have proven several theorems in an elementary way, relying only on our imagination and our common sense. Consider the following “proof” that “every angle is a right angle.” Even experienced geometers often struggle to find the error in the proof. Assertion: Every angle in the plane is a right angle. Proof : Let ABCD be a quadrangle with the following properties (Fig. 1.49, upper left): (1) ∢ABC = 90○ , (2) ∢BCD = α =/ 90○ , (3) AB = CD.

44

An idealized world made of simple elements

Fig. 1.49 Our quadrangle, the point M , congruent triangles, M outside.s

The perpendicular bisectors m1 and m2 on BC and AD are not parallel due to (2) and (3) and thus intersect at a point M (Fig. 1.49 lower left). Let us now compare the triangles ABM and DM C (Fig. 1.49 upper right). According to precondition (3) overlineAB = CD and thus BM = CM (M lies m1 ) as well as DM = AM (M lies on m2 ). Both triangles are, thus, congruent and have, thus, the same angles: α1 = ∢M CD = ∢ABM = α1′ . Since M BC is isosceles, it follows that α2 = α2′ and finally α1 + α2 = α = α1′ + α2′ = 90○ . Thus, the proof appears to be finished if M lies inside the quadrangle ABCD. This point may still lie outside of the quadrangle (Fig. 1.49 lower right). In this case, we get congruent triangles ABM and DCM as before and thus the equal angles ∢DCM = ∢ABM as well as ∢BCM = ∢CBM (the triangle M BC is isosceles). This time, if we calculate the difference of the angles, we also get ∢BCD = α = ∢ABC = 90○ . ⊙

As we can see, appearances can be deceiving – even in two dimensions! Can you find the error in the proof? ◂◂◂

1.6 Projective and non-Euclidean geometry

45

1.6 Projective and non-Euclidean geometry In this section, the geometrical circumstances will be presented from a different point of view. This way, projective geometry becomes the basis for many new insights – and the explanation for otherwise perplexing oddities of geometry. Why, for example, is a circle defined by three points and a parabola by four, but it takes five points to define an ellipse and a hyperbola? Why do two circles possess a maximum of two intersections, but two arbitrary conic sections up to four? The solution lies in two-fold arrangements: Firstly, the line at infinity should not be considered as unreachable. Secondly, non-real elements of the drawing plane, and complex conjugate points and straight lines in particular, should also be accepted. Working with elements at infinity can actually be made plausible through a “dimensional jump” from the drawing plane into space. The “complex extension” of the plane requires a jump into four-dimensional space which cannot be visually imagined. Interestingly enough, geometries that deal with higher dimensional spaces actually exist and achieve important results for “regular” geometry.

Let us discard lengths and angles Projective geometry is a very important field of geometry – it limits regular geometry insofar as it completely discards all congruence relations. Terms such as the length of a line segment or the size of an angle become irrelevant. Hence, the concept of parallelism has to be changed. Pythagoras’s theorem and the Law of Right Angles (see page 75) from descriptive geometry cannot be stated in projective geometry. The incidence relation becomes all the more important: Do three points lie on a straight line? Do three planes intersect in a straight line? The conclusions can be directly carried over to Euclidean geometry, even if it allows for points at infinity, which we have defined as the intersections of two parallel straight lines. Projective geometry makes use of terms such as point, straight line, and plane – as well as incidence relations such as “lies on” or “intersects”. This immediately recalls the duality principle that we have already discussed. For each theorem of projective geometry, the corresponding dual theorem is automatically correct and does not need to be proved. The proof of the dual statement can be omitted because the original statement merely needs to be dualized, i. e., the terms points, lines, planes have

46

An idealized world made of simple elements

to be changed to planes, lines and points respectively; ∪ and ∩ have to be interchanged, while incidence relations are retained.

The dimensional jump Let us consider the Euclidean plane πe , this time “embedded” in space: It could, for example, be the locus of all points with height zero. Now let us project all elements of this plane from a center point Z that does not lie in πe , such as a point on the z-axis other than the origin.

Fig. 1.50 We escape into space

Each point gives rise to a line (ray) that is the connection of a particular point with Z. Thus, lines become planes if projected from Z. The new objects are elements of a star with apex Z and planar geometry thus becomes the geometry in a star in space. In order to understand the situation planimetrically, let us intersect the pencil with an arbitrary plane π that does not pass through Z. Now, any point in πe corresponds to a point in π and any straight line in πe corresponds to a straight line in π.

Ranges of points and pencils of straight lines If a point Pe in πe moves on a straight line ge , then the corresponding pencil of rays moves in a projection plane γ – thus, the corresponding point P in π moves on a straight line g = π ∩ γ. This functions unambiguously in both directions. The (dual) analogy may be drawn for pencils of straight lines in πe and π. The mapping π ↦ πe is a perspectivity with axis a = πe ∩ π and center Z.

Projectivity = likewise linearity

In a last step, let us, once again, rid ourselves of the idea that we have escaped to space. Let us “merge” both planes by arbitrarily positioning them next to each other. The alternating linear relationship (collineation) between both fields is preserved – but in general, we now have neither a center nor an axis of collineation. If we are working in the Euclidean plane, we are performing

1.6 Projective and non-Euclidean geometry

47

Euclidean geometry, and if we work in the projective plane, we are performing projective geometry.

A conic section always remains a conic section

Fig. 1.51 Intersections of a cone of revolution

In the pencil through Z, a circle ke in the Euclidean plane πe corresponds to a circular cone that is (generally) not right, i. e., it is not a cone of revolution. This is what we call a quadratic cone. Common sense might suggest that the cone should be elliptic, but if the section plane π is “steep enough,” it may yield a hyperbola as intersection curve or, as a special case, a parabola. We would then have to speak of a hyperbolic or a parabolic cone – though it is the same cone. Let us, therefore, simply state that the cone is quadratic, which relates to its algebraic property that it always possesses two intersection points with an arbitrary straight line (if mere touching counts as two intersections and non-real solutions are allowed).

Fig. 1.52 Affinely distorted cones

In Euclidean space there exist no elliptic, hyperbolic, or parabolic cones – only quadratic cones. It is, therefore, not necessary to distinguish between the various types of conic sections in projective geometry.

48

An idealized world made of simple elements

The line at infinity is suddenly “completely normal” Is it really impossible to tell these types of conic sections apart? What is the difference, planimetrically speaking, between an ellipse, a hyperbola, and a parabola? The number of points at infinity is obviously important: A hyperbola has exactly two, a parabola exactly one, and an ellipse none (in real space).

Fig. 1.53 Arbitrary quadratic cones

The Euclidean plane has an infinite amount of “points at infinity” – any point at infinity belongs to all straight lines parallel to a certain direction. In the first chapter, we have decided that each straight line only has one point at infinity even though we could have also assumed two. This will now prove to have been very reasonable. If we now draw a straight line of each direction from Z, then they form a plane that is parallel to πe . It intersects π in a “completely regular” line u (if π is not parallel to πe ), namely, the image of the line at infinity of πe . The distance to an arbitrary point at infinity Ue of the Euclidean plane is, according to the construction, parallel to the pencil straight line ZUe , which intersects the projective plane π in a point U on the image of the line at infinity u (Fig. 1.55).

Fig. 1.54 Three types of conic sections

Fig. 1.55 This is how a line at infinity can be derived.

Fig. 1.54 now shows symbolically how we can distinguish the three types of conic sections: by means of their relative position to a regular straight line u.

1.6 Projective and non-Euclidean geometry

49

Non-Euclidean geometry In the previous sections, we have discussed the geometry of Euclid , which is essentially equivalent to the kind of geometry that we are familiar with and use every day. It is based on a system of axioms, a collection of selfexplanatory assumptions that are not further proven. Theoretically, it is now possible to create new geometries that are based on other axioms. However, this entails the enormous restriction that the entire system of axioms must be completely non-contradictory. It should, therefore, be impossible to derive two theorems from the system that prove mutually opposing things. Moreover, a system of axioms should, if possible, be independent and complete, even though this aspect is not essential. In fact, such systems of axioms have already been found. The corresponding geometries can be seen – like the Euclidean – as some kind of playing around, with terms and axioms as rules of the game. As fascinating as this game may be: if the geometry in question stands in strong contradiction to our usual understanding, and if it does not produce any results that are worth mentioning, then it is doomed to be insignificant. Euclid ’s system of axioms had a real “bone of contention,” namely the Parallel postulate: Through each point P in a plane there exists exactly one line that is parallel to a given line not through P . For many centuries, nobody doubted this self-evident assertion. It has, however, been impossible to prove it by means of the other axioms, thus necessitating its status as an axiom of its own. Gauss, Lobatschewskij , and Bolyai realized almost at the same time (but independently of each other) that it could be replaced by contrary axioms without causing the entire system of axioms to become contradictory. The thus emerging geometries were called non-Euclidean geometries. It is basically possible to differentiate between two types of non-Euclidean geometries: hyperbolic geometry, where there exists an infinite number of parallels through each point, and elliptic geometry, which was discovered somewhat later by Riemann and contains no parallels at all.

What’s so fascinating about this? What is fascinating about these geometries is that they play around with the concept of parallels, and thus, with the concept of infinity. “Locally speaking,” “our” Euclidean geometries are barely different from their non-Euclidean cousins. Thus, any creature that inhabits its own small space and is not concerned by far-away objects would not be aware of the inherent difficulties. No wonder that modern physics, which concocts theories about the formation and the expansion of the universe, is very interested in these geometries.

50

An idealized world made of simple elements

We will further see that things appear “entirely normal” if we look at the issue “from a higher perspective”: If we project the objects of the elliptic plane from a point off the plane, we get Euclidean geometry in a star that should be quite familiar to us by now. If we now intersect the rays of the star with a sphere centered at the apex of the star, we are, once again, dealing with geometry in a sphere.

Fig. 1.56 Left: sphere model of the elliptic plane (measurement of angles). Right: On a sphere, you can construct in a similar way as on a plane. This image specifically illustrates the so-called “string construction,” which yields a spherical conic section. It shows that, as in a plane, the tangents of the curve bisect the angle between the lines to the foci. The points S1 and S2 can, therefore, also be identified as focal points: the pencil of rays through one point is reflected by a pencil of rays through the other point.

If the elements of the hyperbolic plane are projected onto a surrounding sphere, then they can be thought of in much more traditional Euclidean terms. A hyperbolic creature can never leave the boundary of the sphere. A straight line of the hyperbolic plane corresponds to a projected circle on the sphere. It possesses two intersections with the world boundary, and thus, two “points at infinity.” Through an arbitrary point on the sphere, there now exist two different projecting circles through these points at infinity. Every point on the straight line that lies outside the sphere and plays no role in hyperbolic geometry. Therefore, it can be stated that all straight lines that occupy a whole sector are mutually parallel in the hyperbolic sense. If we now dare a dimensional jump and take advantage of the conditions in three-dimensional non-Euclidean space, we have almost arrived at the ideas of Stephen Hawking, who speaks of unimaginable cosmic phenomena that, if seen from a higher dimension, are not at all unusual.

Geometry on the sphere Let us perform non-Euclidean geometry on the surface of a sphere. We define “line segments” as the shortest connections between points (great circles). The equator and all circles of longitude are, thus, “straight lines”; arbitrary circles of latitude are not. By means of such straight lines, it is now possible to define objects such as triangles.

1.6 Projective and non-Euclidean geometry

51

Fig. 1.57 On a sphere, you can construct in a similar way as on a plane. This image specifically illustrates the so-called “string construction,” which yields a spherical conic section. It shows that, as in a plane, the tangents of the curve bisect the angle between the lines to the foci. The points S1 and S2 can, therefore, also be identified as focal points: the pencil of rays through one point is reflected by a pencil of rays through the other point.

It is thus possible to describe geometry on the sphere just as well as in the plane. It must be remembered that the sum of angles of such a spherical triangle always exceeds 180○ . All Euclidean axioms are still applicable, except for the parallel postulate: On a sphere, two different straight lines (great circles) always share two common points and can, thus, never be “parallel.”

Fig. 1.58 The lengths a, b, and e at planar and spherical conics

Fig. 1.57 and Fig. 1.58 shall illustrate how constructions of the Euclidean plane can be transformed onto the sphere. Angles and lengths have to be interpreted differently. The lengths a, b, and e in the Euclidean plane correspond to the arc lengths of great circles on the sphere – and, thus, to angles.

52

An idealized world made of simple elements

The curvature of space

Fig. 1.59 In the vicinity of large masses, space appears to be curved – and thus, non-Euclidean.

Going one dimension higher, we have reached the ambient space. Just as the “inhabitant of a sphere” cannot immediately detect that “their” supposedly straight lines are actually curved (see also application p. 264), we do not really know the (eventual) trajectory of light rays (Fig. 1.59)! We know from modern physics that light is deflected by large mass (and even “swallowed” by black holes). In the vicinity of large masses, space appears to be curved – and thus, non-Euclidean. Since Einstein’s general theory of relativity, we have to look at things differently.

Fig. 1.60 Curved spaces

⊕ Remark : The question about the large-scale Euclidean nature of space is not yet conclusively answered, but as soon as astrophysicists surmount this challenge, they will also have answered a seemingly unrelated issue: Will our universe, which was created in a Big Bang, collapse in the far future in a Big Crunch? Interestingly enough, the answer to these questions appears to lie in the determination of the mass of Neutrinos. Neutrinos are inconceivably small particles that travel through space at nearly the speed of light and effortlessly penetrate mass on their way. Thus, the question about the largest seems intimately linked to the question about the smallest . . . ⊕

2

Projections and shadows: Reduction of the dimension

This chapter deals with projections from space onto a plane. Such a projection is the basic idea of perspective, which was first explored in the Renaissance. While this kind of projection makes things more vivid, it does not make them easier. Classical Descriptive Geometry, which emerged at the end of the 18th century, uses special kinds of projections. In particular, these are the normal projections in the “principal directions.” This deliberate dimensional jump can often simplify the solution of problems. Shadows do not only make images more interesting, they also offer additional information: While a spatial situation can never be unambiguously reconstructed from one image, shadows make this task much easier. One of the goals of Descriptive Geometry is to describe spatial objects by means of two “associated” normal projections. In these, it is then possible to manipulate the images with well-developed techniques in order to measure lengths and angles, and if necessary, to reconstruct the object in space.

© Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_2

53

54

Projections and shadows: reduction of the dimension

2.1 The principle of central projection The points in space are pushed into a plane Let us imagine an arbitrary fixed projection plane or image plane π in space and a fixed center of projection Z that does not lie in π (Z ∈/ π). A straight line p = ZP through an arbitrary point P in space shall be called a projection ray. P must, therefore, not coincide with the center of projection (P =/ Z). The intersection of p with the image plane results in the projection P c (the image point) of P . It does not matter if the point is in front of the image plane, behind it, or if it is even behind the center of projection. All points that lie on the same projection ray have the same image point. How else could the entire space be squeezed into a single plane?

Fig. 2.1 Central projection of points with a viewing cone or a viewing pyramid

Photography is (essentially) a central projection. The eye (the optical center of the lens) lies between the object and the image plane (the light-sensitive surface). Due to the limited viewing angle of the lens, only points within the “viewing cone” are actually pictured. Furthermore, due to the rectangular form of the negative (or the light-sensitive chip), this cone is further reduced to a frustum (“viewing pyramid”).

Points at infinity are absolutely normal If we are lucky, the projection ray p will intersect the image plane in a “proper point” P c = p ∩ π. This rule is equally valid for points at infinity. Points at infinity Pu are given by the direction of a straight line: the projection ray p is, then, simply parallel to this direction and intersects the image plane at a point Puc , which is no longer at infinity (Fig. 2.2 left). Points at infinity in the image plane are exceptions as they lie in π and thus do not have to be projected. Their image points are, therefore, also points at infinity (Fig. 2.2, right).

2.1 The principle of central projection

55

Fig. 2.2 After central projection, points at infinity become proper points (see left). An exception: the points at infinity in the image plane are identical to their projections, and thus remain fixed (see right).

Points can “disappear” In unlucky cases, the projection ray p may lie parallel to the image plane. The image point thus resides at infinity even though the point itself does not need to be a point at infinity: it only needs to lie in the particular plane πv that contains the center Z and is parallel to π (πv ∥ π, πv ∋ Z). Such a point is called a vanishing point and the plane πv is called the vanishing plane (Fig. 2.2, right). We thus see: all points in space (including the points at infinity) that do not lie in the vanishing plane have image points that are not points at infinity.

What happens to straight lines? Let us now map a straight line in space, which is, of course, done by mapping all of its points. You will now correctly assume that it is only necessary to map two points A and B of a straight line g in order to get the connecting straight line of the image points as an image of the entire straight line: g c = Ac B c . This is easy to prove: the projection rays through all points of g form the plane Zg, which, indeed, intersects the image plane π in a straight line: g c = (Zg) ∩ π.

A linear mapping Central projection is, thus, “line preserving.” This should not come as a surprise, as we know (from photography) that straight edges of buildings or floor ledges also appear as straight lines. Every day, we see hundreds of photographs in books and in magazines, and therefore, this observation appears “natural” to us. In a separate chapter concerning perspective images, we will discuss what exactly is so “natural” about it. In any case: central projection is “simple” because it is linear, or line preserving. We have already dealt with a linear mapping, namely, the polarity with respect to a circle or a sphere; however, while in those cases, points were transformed to straight lines or planes, central projection maps points to points and straight lines to straight lines.

56

Projections and shadows: reduction of the dimension

The mapping only works in one direction There still remains a big difference to polarity: the latter works in both directions, whereas central projection is not invertible. In other words: a spatial object cannot be “reconstructed” from one photograph (Fig. 2.3, left). Additional data is needed; for instance, it is essential to know whether or not the spatial object in question is a cuboid. If that is the case, then the spatial object can, indeed, be reconstructed true to scale (Fig. 2.3, right).

Fig. 2.3 Two pairs of objects with identical projections

“3D scanning” has become a highly relevant problem recently, and one that has not yet been solved to complete satisfaction. Laser beams are often used to detect objects – a process that not only determines the geometric projection but also the distances from the projection center. However, this method is problematic for very large objects (such as reconstructions from the air) or microscopically small objects. In order to guarantee an accurate reconstruction of complicated objects, one usually needs a larger number of high-quality photographs.

From my perspective . . . Central projection (usually called perspective) will be a major concern in Chapter 9. Perspective images are of great importance in painting and architecture, and most people find “interesting perspectives” appealing. This may be due to the fact that perspective images convey a very subjective and personal impression. After all, it is often said that “from my perspective, things seem such and such.”

A closer examination of objects at infinity Central projection can also serve as a linking tool between Euclidean and projective geometry, where different rules need to be established. The mere fact that a central projection allows us to pull points and lines at infinity into the image plane and thus within our reach is a fascinating fact, isn’t it? The usefulness of assigning only one point at infinity to a straight line once again becomes apparent (in central projection, it becomes a regular point on the straight line). The term “line at infinity” in a plane now becomes comprehensible: if one projects all points at infinity that lie in a plane ε that is not parallel to the image plane, then all projection rays lie in a plane ε through the center Z that is parallel to ε. It intersects the image plane in a “proper” straight line.

2.1 The principle of central projection

57

Central projection of planes The term plane at infinity is not as easily understood using central projection – although the plane at infinity can be mapped point by point, all these image points put together fill up the entire image plane. The planes that contain the center Z are exceptions: they contain an infinite number of projection rays that only have a single image point, and thus, the planes through Z appear as straight lines.

Fig. 2.4 Parallel lighting (roof of a tent, seen from below)

⊕ Remark : Central lighting Tacitly, we have always considered an “eye point” or a center of sight instead of a general projection center. It should be noted that central projections often occur in relation to shadows. The light source need not be infinitely far away (even though this is often assumed for the Sun and the Moon). Besides, many “finitely far” light sources can only be simplified as points in a broad sense.

Fig. 2.5 Two-sheeted hyperboloid of revolution in theory and in practice

Not even a conic spotlight provides light rays that exclusively originate in one point. This would need a so-called two-sheeted hyperboloid of revolution (Fig. 2.5), which we will discuss later. Still, it is true that every finite point-shaped light source produces a central projection from space to the shadow-receiving surface (which is often a shadow-receiving plane). ⊕

58

Projections and shadows: reduction of the dimension

2.2 Parallel projection and normal projection by means of restriction Roughly speaking, central projection is comparable to the photography of space. The farther the center of the lens (which, in geometric terms, means the projection center, the eye point or the light source), the more likely it is that the viewing rays (projection rays or light rays) are parallel. Fig. 2.8 shows a photo from the air, where the relative distance is already very large. Fig. 2.7 shows a normal projection, i. e., the center of the lens is infinitely far away, whereas Fig. 2.6 shows a general (oblique) parallel projection.

Fig. 2.6 Oblique parallel projection . . .

Fig. 2.7 . . . and normal projection

If the center of the projection (eye point or position of the light source) is a point at infinity, the rules of central projection still apply. However, the viewing rays or light rays are parallel; this implies an important property: Parallel projection preserves the parallelity of lines: If two straight lines in space are parallel, then their parallel projections are also parallel (unless they appear as points). Proof : Let a ∥ b be two parallel straight lines in space. All projection rays through the points of a and b form two parallel planes α and β. These two planes are to be intersected with the projection plane π in order to find the images of a and b. The three planes α, β and π share a point at infinity U , which remains fixed during projection as it already lies in π. The image lines ap = α ∩ π and bp = β ∩ π pass through U and are, therefore, parallel. ⊙

However, the converse of the theorem does not hold: If two straight lines have parallel images, we may not conclude that the corresponding lines in space are parallel. From the preservation of parallelity, we can immediately infer the preservation of affine ratios under parallel projection: Parallel projection preserves affine ratios, i. e., it preserves the ratio of lengths of segments on the same (or a parallel) straight line.

2.2 Parallel projection and normal projection by means of restriction

59

Proof : Let g be a straight line with three points P , Q, and R on it. The trace point G = g ∩ π of the straight line remains fixed during (parallel) projection (⇒ g p ∋ G). Both legs g and g p lie in the plane and are now intersected by parallels (projection rays) through P , Q, and R. From the intercept theorem, we can conclude P Q ∶ QR = P p Qp ∶ Qp Rp . ⊙

Preservation of parallelity and preservation of affine ratios are invaluable when drawing an “oblique projection” or when reconstructing a spatial situation from an oblique projection. We consider a Cartesian coordinate system (and its origin U ) to be attached to an object (such as a cuboid). The three coordinate axes x, y, and z are mutually perpendicular lines in space and concurrent in U . We fix the unit points on the axes.

▸▸▸ A simple depiction by means of a horizontal projection In practice, one type of parallel projection is widely used: the horizontal projection (also called horizontal axonometric projection). In this projection, the image of the x-axis is chosen arbitrarily (for example, at an angle α ≠ 0○ to the horizontal, Fig. 2.9). The image of the y-axis is perpendicular to the chosen image of the x-axis, and the image of the z-axis “looks upwards.” x- and y-values remain undistorted while the z-values may be arbitrarily shortened (although it is also possible to leave them undistorted).

Fig. 2.8 Normal projection . . .

Fig. 2.9 . . . and horizontal projection

Fig. 2.9 demonstrates how pictures of some descriptive quality can be “conjured up” using only a small number of lines. This procedure is especially useful for objects that have a complicated floor plan but whose construction barely changes with height (such as prisms and cylinders of revolution). Obviously, this applies in particular to city maps: All streets and floor plans can thus be depicted and remain undistorted (except for the scale); it is, therefore, possible to measure lengths and angles in horizontal planes. The oblique view presents information in the same image about the relative height and appearance of the buildings. ◂◂◂

60

Projections and shadows: reduction of the dimension

Fig. 2.10 Oblique or . . .

Fig. 2.11 . . . normal projection: informative

Fig. 2.12 Perspective views with horizontal axes come close to normal projections with a horizontal axis. On the left: An architectural model by Lukas Galehr. On the right: Since it can be assumed that the coral fishes are similar to each other, multiple views are combined in a single image.

Fig. 2.11 and Fig. 2.12 show (good approximations to) normal projections of a scene. These images allow conclusions that are much more difficult to deduce based on central projections. It can, for instance, immediately be said whether or not the three objects in Fig. 2.11 are positioned uniformly or if the layer of snow on all three chairs is equally thick. ▸▸▸ Reconstruction of a spatial situation based on shadows How high above the ground is the cat in Fig. 2.13? Solution: The picture shows two near-parallel projections (long telescopic lens) of a cat “galloping” on a slightly inclined hill. Let us pretend to be Sherlock Holmes for a moment: The picture on the right almost seems like a composite photograph: Only on close inspection do we recognize a possible shadow on the right side. The left image (taken only moments later) confirms our assumption. The sunlight, therefore, falls at a very flat angle. This means that the scene must have taken place only shortly after sunrise or shortly before sunset. The dew is still glittering on the grass – so it must have been morning. So then, is it possible to say how high the “flying” cat in the right image might be?

2.2 Parallel projection and normal projection by means of restriction

61

Fig. 2.13 How high above the ground is the cat? The shadow provides the answer!

Let us be a little broad in our assumptions: The hill is obviously an inclined plane. The light comes quite precisely from the side. One anticipates the shadow P s of the left back paw P . We can now draw a triangle P P ′ P s , whose side P ′ P s is parallel to the hill direction (P P ′ is perpendicular). The distance P P ′ indicates the distance of the jump: If the cat’s pelvis height is assumed to be 30 cm (the animal appears to be relatively young), then the height of the jump would be almost half of that – perhaps about 12 cm.

Fig. 2.14 A scarab beetle is taking off from a car roof. Shadows and reflections provide useful information about the spatial situation.

Fig. 2.14 shows another situation where you can train your skills. Here, we have reflections in the base plane (a car roof) in addition to the cast shadow and therefore three projections in one image. ⊕ Remark : In our considerations, we have used the preservation of parallelity under normal projection and also the preservation of affine ratios under parallel shadows. On an actual photograph taken with a physical lens, we would need to proceed

62

Projections and shadows: reduction of the dimension

with much greater precision. We will later return to this problem and address it in greater detail. ⊕ ◂◂◂

The following theorem can sometimes be very useful: Two straight lines in space are parallel if they appear parallel in two parallel projections. They are guaranteed to be parallel if they appear parallel in three “independent” parallel projections. Proof : If the images of two straight lines a and b are parallel under a parallel projection, then they lie on two parallel planes α1 ∥ β1 that appear as straight lines. If the straight lines are parallel in a second parallel projection, then (as a rule) they also lie on two further parallel planes α2 ∥ β2 , and then, a = α1 ∩ α2 ∥ b = β1 ∩ β2 . However, it is possible that a and b are skew, and by complete chance, both projection directions are perpendicular to the common normal n of a and b. In this case, only a parallel projection that is not perpendicular to n is helpful. The three projection rays through a point in space must, therefore, not lie on a single plane. ⊙

▸▸▸ Radar corner reflectors and cat’s eyes A construction as in Fig. 2.15 is often found on smaller ships. It is to be shown that this reflector, composed of three mutually perpendicular squares, reflects all incoming rays (and radar rays in particular) “back to the sender.” The retroreflectors on bicycles (“cat’s eyes”), which reflect the headlights of cars, work in the same way.

Fig. 2.15 Dangling radar corner reflector on a ship

Fig. 2.16 “Cat’s eye”: different magnifications of a retroreflector on wheel spokes

Solution: The two-dimensional analogue is known much better: A billiard ball is reflected by the “double cushion” and, at least theoretically, returns parallel to the original direction. The proof for this can be seen on the left of Fig. 2.17: If one takes into account the law of reflection (“angle of incidence = angle of reflection”), then the ray returns, with the respective denomination of angles, at an angle of 90○ + (ε − 90○ ) = ε. And now the jump into space: Let us look at the situation such that two of the three reflecting planes appear as straight lines. Such a principal view produces

2.2 Parallel projection and normal projection by means of restriction

63

Fig. 2.17 Reflection of a billiard ball

precisely the aforementioned billiard problem. The reflection in the projected planes corresponds to the planar double reflection, and the reflection on the third – frontal – plane is not apparent: The reflection normal appears as a point, and both the incoming ray and the reflected ray lie on the same plane that appears as a straight line (Fig. 2.18 center, left, and right)!

Fig. 2.18 Reflection in the corner of a cube (center: plan view and front view)

Relative to the direction of incidence, we can, thus, see the ray as parallel in all principal views. However, if two straight lines appear parallel in three independent parallel projections, then they are also parallel in space! ◂◂◂ Fig. 2.17 on the right resolves the following problem: How must a billiard ball be hit if it should return to the starting point P ? The path of the ball (the angle of incidence) is first reflected by the first cushion. Whichever direction it is, it must pass through the mirrored starting point P ∗ . After having been reflected once, the ray must pass through the finishing point Q = P . It must also pass through the point Q∗ , which was mirrored by the second cushion. This finally and unambiguously defines the once-reflected ray. ▸▸▸ Mirror optics instead of refractive lenses Almost all animals use the refractive properties of lenses or crystals in order to focus light on their retina. Crayfish as well as some shrimp and lobster species employ a different trick: They have special compound eyes where the inside of each facet is a mirror cubic prism. How does this work?

64

Projections and shadows: reduction of the dimension countless thin quadratic prisms

normal projection

top view

direction of ray

retina

Fig. 2.19 Left: In a rectangular prism that is specular inside, one part of the incoming light rays is reflected exactly once “from the cushion” in such a manner that the ray exits in a parallel course when viewed from the top. Right: When many such thin prisms are arranged on a spherical surface, the parallel light rays are partially focused on a concentric sphere.

Solution: The underlying geometry was discovered by Klaus Vogt in 19801 : when a light ray enters such a specular cubic prism, there is, depending on the angle and direction of incidence, a lower or higher possibility that the ray will get to the other side “into the open air” after being mirrored exactly twice at two consecutive faces of the prism. (Some light rays are reflected more often, others exit the prism without any reflection.) When we look in the direction of the prism axis (top view), the light ray appears to bounce “off the cushion” like a billiard ball (Fig. 2.19 on the left). Its inclination towards the prism axis is thereby retained. If the prism is very thin, the double reflection will look to a good approximation like a simple reflection on a virtual plane ε (projecting in axis direction) that is orthogonal to the top-view direction of the light ray. The incident and reflected light rays form the same angle with ε. We will now squeeze thousands of such thin prisms onto the surface of a sphere (Fig. 2.19 on the right) and illuminate this system in the given direction s⃗. Let us now look at the prisms whose axes are inclined to s⃗ at the same angle α (they cluster around a small circle on the sphere). All light rays that undergo the special double reflection are then reflected as though they were reflected by hundreds of virtual planes ε that touch a cone of revolution with a half angle of aperture α. Accordingly, the reflected rays form a cone of revolution. The distance between that cone’s tip and the sphere center is – as one can figure out easily – approximately half the sphere radius. In every light-ray direction s⃗, there are many light rays focused on a point that lies on a concentric sphere. Loosely speaking, we could say that light rays from points that are “farther away” in space are focused with great light 1 K.

Vogt: Die Spiegeloptik des Flusskrebsauges, J. comp. Physiol. 135: 1–19

2.2 Parallel projection and normal projection by means of restriction

65

intensity onto a point of a concentric sphere (the retina). This is the same principle that we know from geometrical optics. The sole difference to a lens eye is that no lenses are needed here!

Fig. 2.20 Reflector eyes can be found in crayfish and several shrimp and lobster species. They can be recognized by their rectangular pseudo-pupils (black spots that change their position depending on the position of the spectator.)

As can be seen in Fig. 2.20, the reflector eyes of crayfish and shrimps are not spheres but ellipsoids, to which the above considerations can also be applied. Eyes based on mirror optics can be recognized by their “pseudo-pupils”, which are almost rectangular. Inside these rectangles, the light rays coming from the direction of the spectator land on the retina in the manner described above. Their quadrangular shape is due to the quadrangular form of the individual facets. The non-square shape results from the fact that the retina is not a perfect sphere. The facets appear black because no light is reflected back to the spectator. That is why the position of the pseudo-pupils changes with the position of the spectator. ◂◂◂

66

Projections and shadows: reduction of the dimension

2.3 Assigned normal projections

Fig. 2.21 Two projections convey much more information than just one.

In order to capture an object unambiguously, we need, in general, at least two projections. Fig. 2.22 shows (almost) synchronous photographs (central projections) of a cat in mid-flight. Under ideal conditions (and given completely synchronous photos), it would be possible to reconstruct the positions of all visible body parts from several of such pictures.

Fig. 2.22 Two different (almost) simultaneous projections

Normal projections are much better suited for this than photographs. If, in addition, the projections are not picked arbitrarily but perpendicular to each other, it further simplifies the reconstruction.

2.3 Assigned normal projections

67

In most cases, we can easily attach a Cartesian coordinate system to an object (Fig. 2.21, Fig. 2.23). The normal projections to the coordinate planes thus become the principal view s. The projection towards the z-axis becomes the plan view (or top view ), the one towards the y-axis becomes the front view, and the one towards the y-axis becomes the right side view (or profile view ). If a point in space is defined by the coordinates P (x, y, z), then its principal views have the coordinates P ′ (x, y), P ′′ (y, z), and P ′′′ (x, z). Any two out of the three views share one coordinate, so that they can be assigned to each other. If the plan view is drawn underneath the front view, then there exists an ordering line from P ′ to P ′′ (Fig. 2.24). The coordinates of each point can be read from plan view and front view alone. The double y-coordinate defines the ordering line.

Fig. 2.23 On the left: the three principal views (normal projections on pairwise perpendicular planes). On the right: A famous study by Leonardo da Vinci, almost 300 years before Gaspard Monge (Fig. 2.24). The two views pictured side-by-side are assigned normal projections. The undistorted front view of the head above is an additional assigned auxiliary view.

Fig. 2.24 The creation of plan view, front view, and right side view (based on a principle by Gaspard Monge)

68

Projections and shadows: reduction of the dimension

Likewise, there exists an ordering line between front view and right side view, and between plan and side view, as in Fig. 2.30, left and middle. (For a better understanding, a general normal projection is additionally depicted on the right side.) Both assigned normal projections of points in space always lie on ordering lines. The position of the coordinate origin – and thus, the position of the axis projections – is not essential for many applications. The relative position to the planes of reference parallel to the coordinate planes are much more important. ▸▸▸ Which object is it? What does a spatial object look like when its contour in the front view is a square, an isosceles triangle in a profile view, and a circle in the plan view? This may be quite a challenge for a beginner. Even when provided with the principal views of the wedge-shaped object in Fig. 2.25 – where, next to the contours, an additional edge and half an ellipse are visible –, it is not easy to deduce its actual appearance. The solution is a cylinder of revolution which has been cut symmetrically twice. This procedure yields, as we will soon see (on p. 164), ellipses as edges. ◂◂◂

Fig. 2.25 Principal views and a general normal projection

Fig. 2.26 Construction of the unfolding with the help of the principal views (parallel rotation of AS)

▸▸▸ Simple construction of the unfolding (Fig. 2.26) Given a quadratic pyramid, its unfolding (development) is to be constructed. Solution: Let us position the object in the most simple way. The base edges in the plan view appear undistorted. If we rotate an edge about the object axis into a plane parallel to the front plane (such a rotation can be seen in the plan view), then the edge will appear undistorted in the front view. ◂◂◂ ▸▸▸ Assignment problems? One often deals with two or more special views of an object that are put into arbitrary positions. The object is much more easily imagined, however, if these views are brought into assigned position. By the way: This is an exquisite way to train one’s spatial ability.

2.3 Assigned normal projections

69

Fig. 2.27 A sepia in two (almost) assigned projections.

Fig. 2.27 shows two photos of a sepia (squid) that were taken in two almost mutually perpendicular directions. Though they are not normal projections, the pictures can be assigned in a certain way, and together they help to comprehend the complicated shape of the animal. Note the bio-luminescence (a flashlight was shone onto the animal to trigger this reaction). ◂◂◂

Fig. 2.28 Left, center: two special views. Right: assigned position.

Fig. 2.28 illustrates this principle by means of two images of a snail shell, each in mutually perpendicular directions. Despite the fact that these are photographs – and not strict normal projections –, both pictures can easily be assigned (right). This is immediately helpful in the detection of assigned points. Fig. 2.29 shows computer generated images (clams have “mathematical shapes”, see Chapter 7). Here it is perfectly possible to assign different views. The American norm speaks of the plan view, front view, and left side view and right side view. In contrast to Monge’s model, the bottom views and back views are often invoked – a custom which can occasionally cause confusion. Computer rendering (with its capacity to provide arbitrary spatial views

70

Projections and shadows: reduction of the dimension

general normal projection

front view

left side view

top view Fig. 2.29 A clam in three assigned projections and a general normal projection.

with little to no additional effort) has, however, eroded these norms to some extent.

Fig. 2.30 Plan view (center) and the assigned normal projection (left) of a scene (right)

▸▸▸ Shadows on the coordinate-parallel screen planes In the plan view of Fig. 2.30, the parallel shadow on the horizontal ground plane is to be determined with the help of an assigned side view. The direction of the light ray is given in the plan view and right side view. If this direction is offset through the assigned points P ′ and P ′′′ , then the image Ps′′′ of the intersection point Ps is already found in the right side. Its plan view Ps′ lies on the ordering line. ⊕ Remark : Without discussing the example in further detail (we have not yet discussed the shadow of spheres on planes or the shadow of straight lines of spheres), the bounding lines can be found immediately by looking at the light rays tangential to the sphere in the principal views. ⊕ ◂◂◂

2.3 Assigned normal projections

71

▸▸▸ What is broken or dislocated? In Fig. 2.31, the image at the center shows a clear right side view (multiview projection) of the left lower arm: ulna and elbow overlap. Fig. 2.31 shows

Fig. 2.31 Three X-ray photographs – right: front view; center: multiview projection. In the left image, the position is changed by not quite 90○ .

three X-ray photographs of a left lower arm and hand. The images show a wrist fracture, or distal radius fracture. However, one of the carpal bones (the lunate bone) also seems to be “whirring around” (left-most image), which suggests a joint dislocation (luxation). In this image, the position of the aforementioned carpal bone seems fairly “normal” (because there is no luxation). The fracture in the radial bone is clearly visible in the multiview projection. Based on this image, we can also give a good estimate of the angle by which the bone must be realigned for treatment. ◂◂◂ Side views are often utilized in Descriptive Geometry. The witty freehand sketch in Fig. 2.32 (found on a paper fragment) should demonstrate the principle: If one wishes to create a third view to two assigned normal views (such as the plan and front view), which should be assigned to one of the two given views (the front view, in this case), one simply picks a projecting base plane ε in the other (dropped) view perpendicular to the direction of the ordering line (green). In the new view, it also appears as a point and as perpendicular to the ordering line. On the ordering lines in the new view, it is possible to transcribe the distances of ε from the dropped view (blue). Side views will seldom be used to produce coherent images – rather, special views will need to be generated where (for instance) the planes appear as straight lines ([?]).

72

Projections and shadows: reduction of the dimension

Fig. 2.32 Additional side view

Fig. 2.33 Principal projections as shadows

▸▸▸ Shadows provide additional information Geometrically speaking, shadows do not differ from projections. If shadows can be detected in an image, then they provide the same kind of additional information as additional views. Fig. 2.33 shows a mathematically defined heart.2 Due to the shadows on the coordinate planes (they are equivalent to the principal views), the overall shape of the object can be deduced with some accuracy.

Fig. 2.34 Shadows provide additional information.

◂◂◂

The so-called determination of visibility is a frequent problem. Fig. 2.35 illustrates that the position of apparent collision points can sometimes not be judged from a photo. Yet, in some cases, the solution is provided by mere coincidence – in this case, through the shadow (Fig. 2.34) or with the help of a photo taken an instance earlier oder later (Fig. 2.36). Let us ponder what is needed for such a determination in more general terms. ▸▸▸ Determination of visibility for skew straight lines Two straight lines have a point of intersection if they lie in a plane. If they do not lie in a plane, they are “skew.” 2 The

formulas were found at www.mathematische-basteleien.de/herz.htm.

2.3 Assigned normal projections

73

Fig. 2.35 Visibility is often difficult to determine. In the scene in the left image, the orca throws the “stuntman” into the air. Don’t worry: no collision with the column actually took place. In the right image, it can be gathered from some details that the parachute does not become entangled.

Fig. 2.36 A seagull doing a pedicure?

If we imagine straight lines as materialized rods, then one straight line is hidden by the other skew straight line at the apparent intersection point in every view, or it is itself hidden by the latter. In order to make the decision, we need two projections – ideally, assigned normal views. Fig. 2.37 shows a plan view and a front view of two straight lines a and b. The intersection in the front view does not correspond to the intersection in the plan view, otherwise the points would have to lie on an ordering line. The lines a and b are, thus, skew. In the plan view, a point 1 on a and another point 2 on b seem to coincide. If we draw the ordering line through the apparent point of intersection 1′ = 2′ and look for the assigned points 1′′ ∈ a′′ and 2′′ ∈ b′′ , we can decide which point “lies higher” – and is, thus, visible in the plan view. By analogy, the projections 3′ ∈ a′ and 4′ ∈ b′ can be determined for the overlapping points 3′′ ∈ a′′ = 4′′ ∈ b′′ . The point that lies further ahead is visible in the front view. We thus remember: Visibility decisions in a normal projection are done in an assigned normal projection. ⊕ Remark : A draftsman suggests the overlapping of two straight lines by a slight interruption of the overlapped line – thus creating an “aura” around each straight

74

Projections and shadows: reduction of the dimension

Fig. 2.37 Determination of visibility in theory . . .

Fig. 2.38 . . . and practice: The leg positions are confusing enough, but in what way do the ropes pass?

line. Such subtle tricks contribute a lot towards helping our spatial imagination. On the other hand, errors in such determinations of visibility have a negative effect on spatial imagination, and can even “destroy” the mental image of a three-dimensional ◂◂◂ object. ⊕

The following important theorem occurs in many deliberations:

A straight line that is perpendicular to a plane is also perpendicular to each straight line in that plane (whether intersecting or not). Proof : Let us look at a right angle with the legs a and b (vertex S = a ∩ b). If we leave a fixed and rotate b about a, then b generates the normal plane ν ⊥ a. Each arbitrary straight line in ν is parallel to one of the positions of b, and thus also forms a right angle with a. ⊙

Fig. 2.39 Practical application of the constant right angle: the axis of rotation of the excavator scoop drawn in red is perpendicular to the desired ground plane. The excavator can now flatten the incline with the scoop by a rotation of the jib.

Fig. 2.39 illustrates the theorem: an excavator scoop, which rotates about a normal to the skew ground plane, can thus be used to flatten ground soil. Another example can be found in application p. 75.

2.4 Principal lines and the Law of Right Angles

75

2.4 Principal lines and the Law of Right Angles If a straight line is parallel to the image plane and thus perpendicular to the direction of the normal projection, it is called the principal line. Segments on the principal line are not distorted in a normal projection. For principal lines, the following theorem holds: Law of Right Angles: A right angle appears as a right angle in a normal projection if, and only if, at least one of the legs is a principal line and no leg appears as a point. Proof : Let a and b be the legs once more, S = a ∩ b the apex of the right angle, and π the image plane. During rotation about a, b generates the normal plane ν ⊥ a. If a ∥ π is now parallel, then the plane ν appears as a straight line perpendicular to a in the image. If a ∥/ π, then ν does not appear as a straight line. The normals n ⊥ a then form different angles with π. It follows that the special normal b ∥ π is perpendicular to every normal in the image, including a. This law can also be proven elegantly by using vector calculus: We use an adapted coordinate system with a z-axis that is perpendicular to the image plane. Two ⃗ and ⃗b shall be orthogonal in space (⃗ vectors a a ⋅ ⃗b = ax bx + ay by + az bz = 0.) The vectors are orthogonal in a normal projection only if az bz = 0, that is, if az = 0 or ⃗ or ⃗b is parallel to the xy-plane. ⊙ bz = 0, which means that either a

▸▸▸ Non-trivial right angles in a cuboid

Fig. 2.40 Application of the theorem of right angles: A cuboid is displayed in different ways in a normal projection so that the drawn right angle can be seen“undistorted”, i.e. as a right angle. The direction of the projection has to be perpendicular to the edge 12, which can be done in an infinite number of ways.

A good exercise for understanding the theorem is Fig. 2.40: In a cuboid one can find quite a few right angles. One non-trivial example is the triangle 123. Since 13 is perpendicular to the side plane that has 12 as diagonal, it is also perpendicular to 12. Now consider a normal projection of the cuboid. Due to

76

Projections and shadows: reduction of the dimension

our theorem we can see the right angle in 1 if and only if either 12 or 13 is perpendicular to the projection rays. ◂◂◂ ▸▸▸ An abundance of right angles . . . Fig. 2.41 shows two fundamentally different pictures of tower cranes (wideangle and telescopic lens photo). The supporting structures of such cranes form a substantially right angle. Why do all the right angles of the cranes on the right also appear as such in the image?

Fig. 2.41 An eternal construction site: the Sagrada Familia in Barcelona (Antoni Gaudí) has been surrounded by cranes for years (this is part of the concept). The crane towers and their jibs form a right angle, which never appears as such in wide-angle photographs (left). In a telescopic-lens photograph (approximately a normal projection) with a horizontal optical axis, on the other hand, the crane structures will form a right angle, because all the towers are the principal lines.

Solution: The photograph on the left is a classic example of central projection, where the Law of Right Angles only applies in special cases: Both legs of the triangle must be parallel to the image plane (that is, they must be principal lines). The photograph on the right is a nearly normal projection. When the optical axis is horizontal (and the image plane = sensor plane is thus perpendicular), then all the towers of the cranes in the photographs are principal lines, and the Law of Right Angles applies: regardless of their orientation, the jibs always appear horizontally in a photograph. ◂◂◂ A direct conclusion of the Law of Right Angles is the following fundamental rule of drawing that we shall discuss in the appendix about freehand drawing:

2.4 Principal lines and the Law of Right Angles

77

During normal projection, a circle appears as an ellipse whose principal axis is perpendicular to the image of the circle’s axis. The diameter of the circle equals the length of the principal axis.

Fig. 2.42 In a normal projection, the image of a circle c is an ellipse cn . The minor axis of cn is identical with the image an of the axis of the circle a. The semimajor axis equals the radius r of the circle.

Proof : We assume beforehand that the image cn of a circle is an ellipse (we will show this later). Among all diameters of c, only the one on the principal line appears undistorted (Fig. 2.42). Due to all other diameters appearing shortened, the main apices of the image ellipse lie on the principal line. The minor axis of the image ellipse is, therefore, the normal projection an of the circle axis. ⊙

▸▸▸ If and only if

Fig. 2.43 At the indicated positions, there is a right angle in space. In the photo to the right, the helicopter blades appear orthogonally whenever one of the blades is parallel to the sensor plane.

In mathematics, iff is a logical connective between statements, where either both statements are true or both are false. Applied to the theorem of right angles, this can also mean: If we know that we have a right angle in space and we have verified that the angle in a normal projection is also 90○ , then we know that at least one of the legs is a principal line.

78

Projections and shadows: reduction of the dimension

Fig. 2.43 shows two photos of different scenes, in which we know that there is a right angle at the indicated positions. In the photo this angle appears to be under 90○ . (In the photo to the right this only applies to some extent, but let’s say it was an accurate right angle.) The photograph to the left is clearly a central perspective, where the subsequent circular arcs and both legs of the right angle are in planes parallel to the image plane. Obviously, the theorem in such a special case holds also for central projections. The end points of the rotor blades create a circle. Its axis is the rotation axis of the system. In this case, the photograph closely resembles a normal projection which is due to the fact that a strong telescopic lens was used. The image of the axis of the rotating system is thus perpendicular to the rotor blade that appears undistorted. ◂◂◂ ▸▸▸ Luggage X-ray scans – are they normal projections? During luggage controls, smaller luggage bags are screened with X-rays by moving the bag on a conveyor belt and scanning them as orthogonal crosssections (Fig. 2.44). What kind of projection do we get in such a scan?

Fig. 2.44 A photographer’s hand luggage moves through the X-ray tube. The image is not a photograph (= central projection) but a scan which corresponds to an almost orthogonal parallel projection. The Law of Right Angles thus applies to some degree. On the right: a photograph of the same suitcase for further illustration.

Solution: After analysing the left images in Fig. 2.44, we can formulate the following hypothesis: The cross-sections are scanned by moving the X-ray beam through the tube almost orthogonally to the conveyor direction (and thus always in a parallel course). The result is saved onto a “pixel bar” that is orthogonal to the X-ray beam’s orientation, which generates a normal projection of the cross-section. The overall result as the bag moves on the conveyor belt is a parallel projection, but this parallel projection comes very close to a normal projection.

2.4 Principal lines and the Law of Right Angles

79

To consolidate this hypothesis, we can test it on the basis of various criteria. The preservation of parallel lines and of affine ratios obviously apply – as verified, amongst others, by the external hard-drive that is circled in Fig. 2.44. When a normal projection is given, the Law of Right Angles must also apply. This is clearly shown by the rim of the case (dashed coordinate axes), and also in a non-trivial way by the long photographic objectives attached to the cameras: the different annuli of the objectives are positioned orthogonally to the optical axis. The elliptical images of circles should be exactly perpendicular to the image of the axis – which is, indeed, fairly precisely the case here. ◂◂◂

Fig. 2.45 The Law of Right Angles is responsible for the phenomenon that the crescent appears “tilted” at sunset.

▸▸▸ The crescent does not seem to be facing the Sun (Fig. 2.45) At sunset, the Sun disappears below the horizon. If we have waxing moon, it is still above the horizon. One would expect the crescent to be horizontal, as it “faces the Sun.” Yet, it is tilted. Why is that?

80

Projections and shadows: reduction of the dimension

Solution: When we focus on the Moon and zoom in, we have a near-orthogonal projection, which means that the Law of Right Angles applies. The contour of the waxing moon is composed of the contour c of the Moon (a half circle) and the visible half of the “terminator” t, i. e., the circle that separates the illuminated and the dark side of the Moon (see also Application 4.17). In order to get the minor axis of the image ellipse of the terminator, the axis s of the circular terminator t has to be projected on the image plane π. The line s can also be interpreted as the light ray through the center M of the Moon. Fig. 2.45 illustrates how that can be done: Let Z be the spectator and S∞ be the Sun (almost) at infinity. The projection plane π is perpendicular to the principal projection ray M Z. The axis s = M S∞ of the terminator is intersected with π, which leads to an auxiliary point H with H = H n . The projected ray sn = M n H n = M n H obviously has a non-vanishing inclination angle ϕ. The higher the Moon stands, the larger is this alleged “error”. You can find out more about the topic at http://www.grad.hr/hdgg/kog_stranica/ kog13gif/kog13_glaeser.pdf. ◂◂◂ ▸▸▸ When exactly do spring and the other seasons begin (Fig. 2.46)? The beginnings of spring and fall are characterized by the fact that day and night have the same duration (equinox ). Summer and winter begin when the nights are longest or shortest respectively. How can we find their exact points of time?

Fig. 2.46 The Law of Right Angles helps us to find the beginnings of the seasons. Left: general normal projection, right: plan view. (The shape of the elliptic orbit is exaggerated to show the construction more clearly.)

Solution: Due to Kepler’s law, the orbit of the Earth (ecliptic) is an ellipse with the Sun in one focus. The axis direction of the Earth stays constant during the year. If we consider a plan view onto the plane of the ecliptic, the sun rays that reach the Earth are always principal lines.

2.4 Principal lines and the Law of Right Angles

81

The equinox happens when the terminator (see previous application) of the Earth passes through the poles. In this moment, the Earth’s axis and the sun rays are perpendicular. If we consider a top view – that is, a normal projection – of the elliptical trajectory, all the sun rays that reach the Earth are principal lines, because they lie on the projection plane. Since a normal projection is given, the Law of Right Angles applies: The desired right angle between the sun rays and the oblique earth axis can be seen – provided that it is located in space – in the top view, because one leg of the angle is a principal line! The two points at which day and night have the same duration (beginnings of spring and fall) thus lie on a normal with respect to the direction of the top view of the Earth’s axis. Perpendicular to this direction (that is, in the direction of the earth axis in top view), we can find – in a manner that is by no means trivial — the beginnings of summer and winter. We must show that the angle σ between the sun rays and the axis direction is extreme in this position. To prove this, we once again need the Law of Right Angles (Fig. 2.47):

Fig. 2.47 The extreme angle between the sun rays and the earth axis

Let E be the position of the Earth where the plan view of the axis direction runs through the Sun S. A is a fixed point on the axis (EA is constant). A′ is its top view, and C is the foot of the perpendicular from A to the straight line ES. The value σ is determined by the right triangle EAC, and C is its foot on s. The triangle appears in the given position because A′ = C projecting. In any other neighboring position E ∗ or E ∗∗ before or after the special event, the foot C can be constructed by looking for the planar foot from A′ to the corresponding light ray s∗ or s∗∗ , because every light direction is a principal line. This means that both E ∗ C ∗ and E ∗∗ C ∗∗ before and after the special position are shorter than EC, and σ is thus an extreme value in E. We will elaborate on this topic in Chapter 11. ◂◂◂ ▸▸▸ Topographic projection In many areas of application, such as the building of roads (Fig. 2.48, Fig. 5.54 on the right), a single normal projection – the plan view – is sufficient if one also works with “height markings.” This procedure is called topographic projection.

82

Projections and shadows: reduction of the dimension

perspective image

An agricultural road rising point of view

beyond ground level

Fig. 2.48 Topographic projection, from which a central view (perspective intersection method, see p. 369) can easily be constructed (at the top). The planned road is adjusted to a fault scarp, with the cuttings and slopes ideally balancing each other out (redeployment of material). The curved road that steadily rises by 10% has helical margins. The slopes are thus helical developables (see p. 310).

This makes it possible to solve the most common problems (including the involved complex surfaces) in disciplines such as street planning or cartography. ◂◂◂

83

2.5 The difference in technical drawing

2.5 The difference in technical drawing Classical Descriptive Geometry and technical drawing share many of their methods despite the fact that technical drawing utilizes many “drawing shortcuts” in addition to different “rules.” This has enormous advantages during drawing, but requires certain foreknowledge from the reader, such as an awareness about the nature of a section (which we will discuss shortly). To imagine “genuinely” sectioned objects is to commit a fundamental mistake! Technical drawing engineers tend to be very pragmatic. Rules are “suggestions” that should, if possible, be considered. Owing to the impossibility of adhering to all rules simultaneously, an engineer is, therefore, mindful of comments such as “if possible,” “if there is enough space,” etc. ▸▸▸ Special additional views In technical drawing, one also speaks of plan views, front views, left and right views. Usually, as many views are drawn as are necessary. ⊕ Remark : “Devices” (a term occasionally used for such objects) can be viewed in any number of special and general views. Such images aid the spatial imagination of the beholder, but still, it is rare that these devices can actually be built from the images alone (Fig. 2.49, right). SCHNITT A B

A

view X

B

Fig. 2.50 Section through a pipe elbow. Fig. 2.49 For the device pictured here, the front Whatever lies behind the section plane is drawn in. view and an additional assigned view are enough.

Fig. 2.49 on the left shows a device pictured in a typical technical drawing: the front view and an additional assigned view are enough to determine the shape and describe all necessary lengths and angles undistortedly. In technical drawing, thin dot-dashed lines are used for different purposes. They generally represent axes of rotation, but they may also be used for axes of symmetry or – in the form of coordinate axes – to mark the center of a circle. ⊕ ◂◂◂

84

Projections and shadows: reduction of the dimension

▸▸▸ Virtual sections Technical drawing often confronts us with the problem of displaying objects that, even if given many projections, are still very difficult to picture and to dimension. Object sections were invented for this purpose – an imaginary decomposition along a section plane that is usually perpendicular to a body axis or contains the axis. Whatever is contained in the section plane is usually crosshatched (excepting longitudinal sections of braces, ribs, screws, nuts, flat washers, etc.). Whatever lies in front of the section plane is omitted – whatever lies behind is drawn. Fig. 2.50 on the left shows a section through an elbow. In this case, a simple section (AB) is sufficient to depict the location of drilling holes and screws. ◂◂◂ The arrows refer to the viewing direction. ▸▸▸ Multiple virtual sections The drawings in Fig. 2.51 serve to illustrate the necessity for more than one section even when dealing with supposedly simple objects. The following rule holds: With multiple sections, every section is done without reference to the other sections. B

D

A

C

Section AB

Section CD

Fig. 2.51 Multiple sections of a single object: The left-most drawing is a half-section. The other drawings show a left-side view and two additional sections through the object.

On the left, we see a front view of the object (a nozzle). Its symmetrical structure allows us to achieve two goals at the same time: one half of it – right up until the semi-colon axis of symmetry – is depicted as a view (whether it is the top or the bottom half depends on the norm involved). Since the other half is symmetric, it can be pictured as a so-called half-section in order to illustrate the – not all too complicated – interior of the nozzle. Here, the important rule must be noted that the section axis must not be drawn as a continuous line: the section is only virtual! If all parts of the nozzle were cylindrical, we would already be done. This is due to a common assumption in technical drawing that all objects are automatically cylindrical unless otherwise noted. A view from the left (usually drawn from the right side of the front view) shows, however, that at least the head of the nozzle is square. Whatever lies behind it may still be cylindrical or square. In the example, the part between A and B is cylindrical, whereas the thickening to the right of it is square. This can be shown properly in a

85

2.5 The difference in technical drawing

section from A to B (“full section”). Finally, a full section from C to D should indicate that the rest of the nozzle is, once again, cylindrical. Given enough space, overlapping sections are drawn “in sequence.” ◂◂◂ ▸▸▸ Dimensioning Devices should primarily be dimensioned in places where it is expected (where the measurements are not shortened) and secondarily in a way that can be measured on the physical workpiece. For this reason, the diameters of circles (rather than their radii) are usually dimensioned – if necessary with a “measurement across space” (Fig. 2.52 on the left). The diameter sign ∅ is added if the circle appears as an edge. 25

2

5

39.5

o/ 26

6 o/ 20

o/ 38

o/ 14

o/ 20

45´

10 10

28

15

30 215

Fig. 2.52 Dimensioning a workpiece

Fig. 2.53 The aforementioned workpiece, drawn with real sections on the left (wrong!) and transparently in spatial view on the right

In order to dimension invisible drilling holes (and similar features), one works with full sections or half-sections. It is often enough to “rip” the object apart locally – in other words, to perform a partial section. If the object is too long to be displayed in full length, it can be halted by a wavy line or an eight-loop. External dimensions are always important. Closed loops of dimensions are to be avoided. If possible, intersecting dimension lines are to be avoided. As simple as the workpiece in Fig. 2.52 may be, it is relatively difficult to create a comprehensible sketch displaying all details without ambiguity. The computer allows us to use transparency in the drawing. If a quarter of the object is taken out, it might raise the clarity of the drawing, but it can also be misunderstood! ◂◂◂

86

Projections and shadows: reduction of the dimension

▸▸▸ Sections in construction drawings Construction drawings may differ considerably from technical drawings. Even the “norm” is different (1 cm instead of 1 mm). Furthermore, lines are used instead of dimensioning arrows. As with technical drawings, virtual sections are essential.

Fig. 2.54 Building with one horizontal and two vertical sections. Despite the computer simulation, the model remains very important for comprehension. The character of the outer layer is particularly apparent – it holds two different pencils of straight lines! The mirrored floor contributes additional effects to the presentation, but does not exactly improve one’s capacity to imagine the object.

Fig. 2.54 shows a considerably complicated building (architect: Cornelia Faißt) with three assigned sections. Without going into too much detail: nobody can pretend to be able to imagine the object based on the three sections. Surprisingly, some architects have developed the remarkable capability of gaining deep insights into virtually incomprehensible scenes by a series of sections. Still, it is important for every architect to build physical models. ⊕ Remark : In anticipation of Chapter 6, let it be said that the outer wall of the building is formed by so-called HP shells (hyperbolic paraboloids), which hold two different pencils of straight lines (Fig. 6.20, 7.8). The planar sections in Fig. 2.54 of such surfaces are – as the name implies – parabolas and hyperbolas. ⊕ ◂◂◂

3

Polyhedra: multi-faced and multi-sided

Planes are non-curved spatial surfaces. Surfaces which are composed entirely of planar polygons are called polyhedra. Polyhedra have been (and still remain) key to many geometric insights. In recent times, they have also become essential in dealing with computational representations of curved surfaces. These are “triangulated” or subdivided into triangles. Whenever computers deal with arbitrary surfaces (no matter how complicated they are), an approximating polygonal surface is considered – the closer it comes to the true shape of the surface, the finer the triangulation is. As is often the case in geometry, special cases play an important role. For example, there are a few polyhedra that are bounded by congruent polygons – most of them are the so-called Platonic solids. If a polyhedron contains two types of polygons, we get a further class of polyhedra, called the Archimedean solids. Both types of solids appear frequently in nature, and in the microcosm in particular. What was investigated by the ancient Greeks more than two thousand years ago now appears under our microscopes. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_3

87

88

Polyhedra: multi-faced and multi-sided

3.1 Congruence transformations Before dealing with polyhedra, we should discuss the important topic of congruence transformations. They are defined as a spatial transformations where angles and lengths (of the moving object) are preserved (Fig. 3.1).

Fig. 3.1 A congruence transformation, except for the wings

Among the congruence transformations, there are translations and rotations. Both are directly congruent, i. e., they preserve orientations.

Fig. 3.2 Rotations of the magic cube according to Rubik

Fig. 3.2 shows repeated rotations about intersecting axes, not of the entire “magic cube” but of specific layers. In such cases, the theorem of “replacing multiple rotations by a single one” obviously does not apply, not to mention that it is quite a challenge to reverse all of these rotational steps. A computer simulation has an unfair advantage: the program simply records all arbitrary rotations taken by the user and, when the magic cube is to be “solved,” simply runs the steps in reverse (with negative rotation angles).

3.1 Congruence transformations

89

Fig. 3.3 Three (non-uniform) rotations about intersecting and parallel axes

Fig. 3.3 shows three independent rotations about intersecting and parallel axes. They are non-uniform (they are harmonic oscillations), which does not matter from a geometric point of view. By the way: the outermost right axis almost appears as a point. If one combines two rotations about intersecting axes, one gets a rotation about a third axis that runs through the intersection of the two given axes. By the same token, it is possible to split an arbitrary spatial rotation into several rotations about certain axes. This result, discovered by Euler , is extremely important in analytic geometry and kinematics.

Fig. 3.4 Rotation about an general axis

Fig. 3.4 shows a rotation about an general straight line. More specifically, it is the line about which – given this specific type of bicycle – the front wheel can be rotated (let us ignore the fact that this axis slightly varies in the real world during the motion). The position of the Sun in this scene is such that the shadow of the axis of rotation almost appears as a point. If one views the rotation in the direction of the axis of rotation (in the special case, from the position of the Sun), then the motion appears as an “entirely ordinary” two-dimensional rotation.

90

Polyhedra: multi-faced and multi-sided

Reflections in a plane, on the other hand, are indirectly congruent, i. e., they alter orientations. Fig. 3.5 shows an everyday reflection in an upright mirror.

Fig. 3.5 Reflections in a vertical plane. The peacock’s feather on the right touches the non-reflecting glass surface at the front (pushed in fibers).

Such a reflection does not alter left and right, as it is commonly believed, but front and back, which is especially evident in Fig. 3.5 on the right. From a geometric point of view, this statement can be further generalized: A mirror inverts the sign of the distance of a point from the mirror plane.

Fig. 3.6 Reflections in a horizontal plane

Unlike reflections in a plane, reflections in a point are indirectly congruent! In three-dimensional space, orientation can only be defined by orienting a tripod (e. g., three concurrent edges of a cube). At first, Fig. 3.7 gives the impression that it is a reflection. Upon closer inspection, one notices the presence of two separate but essentially directly

91

3.1 Congruence transformations

congruent animals. They can be made to overlap using a simple rotation of 180○ . The axis of rotation is roughly equivalent to the midline of both parallel body axes.

Fig. 3.7 Left: reflection in a plane? Right: reflection in several planes, but not quite easy to visualize (the jellyfish are located behind the reflecting planes.)

Fig. 3.8 Such figures result from . . .

Fig. 3.9 . . . reflections in a trihedron.

The photo in Fig. 3.8 is remarkable: It appears to be a convex polyhedron. Fig. 3.9, however, shows the situation from another point of view: Just a tiny part of the alleged polyhedron is inserted into a spherical “mirror triangle” (in the photo this part is not yet in its final position). Multiple reflections at the sides of the triangular mirror reproduce the part-polyhedron in such a way that it appears as one large closed polyhedron when observed in direction of the rotation axis of the triangular mirror. Fig. 3.10 shows the transformation of a skeleton from a crouching position into a stretched position. In practice, a “composite” of many rotations and translations is required. According to an idea by Hannes Kaufmann, all transitional positions can be efficiently approximated by interpreting them as linear combinations of the starting position and the final position. Computer graphics is particularly interesting for transformations that can be used to animate living creatures in a very realistic way. Professional programs employ such techniques particularly well, and in order to understand them,

92

Polyhedra: multi-faced and multi-sided

Fig. 3.10 This transformation is strictly mathematical

Fig. 3.11 More than congruent transformations

Fig. 3.12 Realistic computer simulation of the above motion

considerable knowledge of kinematics is required. Chapters 10 and 11 of this book are dedicated to this topic. Fig. 3.11 and Fig. 3.12 shall illustrate this.

93

3.2 Convex polyhedra

3.2 Convex polyhedra Loosely speaking, a closed polyhedron is convex if it has no dents. If we connect two arbitrary vertices by a line (chord), then this segment must lie either entirely inside the polyhedron or in one of its faces. Such solids play an important part in our world. They have geometric properties that make them particularly “simple.”

Prisms and pyramids A prism is formed by parallel translation of a polygon (which does not necessarily have to be planar). We can also say: one “connects” a generating polygon with a point at infinity. The second definition leads to a pyramid as a connection of a generating polygon with an arbitrary point. However, this point must not lie in the carrier plane of the generating polygon (if it is a planar polygon) and must not be a point at infinity.

Fig. 3.13 Still huge, even from far away

Seen this way, prisms are simply special cases of pyramids: the apex (tip) of the pyramid is, then, a point at infinity. By analogy, a planar polygon is convex if every possible chord lies within the boundary of the polygon. The following theorem should be immediately apparent: Connecting a planar convex polygon with a fixed point (or a point at infinity) that does not lie in the carrier plane results in a convex pyramid (or a convex prism). The ancient Egyptians have left us the most beautiful examples for regular pyramids. The construction of these colossal objects must have been as difficult as their appearance is obvious. Given a quadratic base with a side

94

Polyhedra: multi-faced and multi-sided

Fig. 3.14 Convex or non-convex polygons? With some imagination, one can find two “almost convex” positions. The corresponding “almost stretched-out” legs would need to be completely stretched.

Fig. 3.15 From a multistage Mastaba to perfection

length of over two hundred meters, even the leveling of the foundation (accomplished to centimeter accuracy) is a true masterpiece. In principle, step pyramids were built first (Fig. 3.15 on the left) and then their surface was flattened. (The peak of the Great Pyramid of Giza is still very well preserved.) 4.500 years (!) ago, immediately after the construction was finished, the appearance must have been even more impressive than it is today.

A series of simple properties As indicated, convex polyhedra possess certain properties that can be very useful for certain geometric considerations. For instance, the following theorem is true: The shadow of a convex polyhedron on an arbitrary plane (as well as its contours) are convex polygons.

95

3.2 Convex polyhedra

The proof uses the “chord-definition” of convexity and it is straightforward: if we imagine such an object as being filled by tense “fibers,” then these also cast shadows that cannot lie outside the shadow contours of the object.

Fig. 3.16 Shadows of convex polyhedra

▸▸▸ Shadows of prisms and pyramids Fig. 3.16 shows the shadows of three simple and convex objects. Shadows of prisms are often bounded by shadows of the generators of the prisms – the shadows of edges of the base and top surfaces form the rest. If the prism stands on the plane on which the shadow falls, then the edges in question are easily found: one only needs to project the light source in the direction of the edges to the shadow-receiving plane and, once there, draw the “tangents” towards the base polygon. Architecture mostly deals with straight prisms and parallel lighting (from the Sun). In this case, the prism edges in question can be found by moving the plan view in direction of the light rays towards the base polygon. For pyramids, we can proceed in a similar way: In this case, all edges run through a point – this is also true for their shadows. Therefore, we get the shadow of the pyramid apex and, from this point, place the “touching straight lines” towards the base polygon. They delineate the shadow polygon. ◂◂◂ A further practical property of convex bodies that also follows from their definition is the following: During projection, every face of a convex body is either completely visible, completely hidden, or it appears as an edge. By analogy – if one considers lighting instead of viewing – the following is true:

96

Polyhedra: multi-faced and multi-sided

Convex objects do not throw shadows on themselves. Their faces are either completely lit, completely shaded, or the light rays through their edges touch along the whole face. ⃗ of ⊕ Remark : Computer geometry takes advantage of this fact. A normal vector n the face of a convex body can always be oriented in such a way that it points towards ⃗ forms an acute angle with the projection ray (or light ray) oriented the outside. If n towards the projection center (or light center) p⃗, then the entire face is visible (or ⃗ ⋅ p⃗. illuminated). It is merely necessary to determine the sign of the dot product n This also holds true with central projections (or central illuminations): In this case, the projection rays (or light rays) usually differ for the points of the face, but the decision whether or not the angle is acute is not affected by this. ⊕

We can derive the following rule from the aforementioned statements:

Rule of Visibility : In the projection (image) of a convex body, only fully visible or fully hidden edges go through a vertex that lies completely within the body contours. The contour polygon is fully visible.

Combination of several convex bodies In practice, we rarely depict one single convex body. The question is: Which of the previously stated practical rules can be applied to scenes that consist of many such building blocks? Let us discuss the procedure using a certain example. Fig. 3.19 shows a non-convex body – upon closer inspection, however, one notices that it is “harmlessly non-convex”: It can easily be split into three convex building blocks: two regular eight-sided prisms and one cuboid extension. While visibility determination for such a body is “trivial” for our imagination, the drawing of the shadows is much less so and requires a disciplined approach.

Fig. 3.17 Systematic procedure: consider the bodies one by one . . .

In a first step, all three partial convex bodies are considered one by one according to the aforementioned rules. In particular, the shadows on the base plane can be determined separately. The entire shadow on the base plane emerges from the “combination” of the separate convex shadow polygons. The thus emerging shadow polygon can easily be non-convex. ⊕ Remark : A hint for freehand drawers (for us, freehand drawing is an important goal to which a whole appendix is dedicated): The shadow on a surface “no longer

3.2 Convex polyhedra

97

knows to which partial body it belongs.” All shadows on a surface adapt the texture of the surface on which they lie. One should, furthermore, not try to highlight the separate convex shadow polygons. Shadows tend to have a “surface-like appearance.” Not even the boundaries of the entire shadow polygon should be particularly stressed: shadow boundaries are usually not sharply delimited – not even in photographs. This is due to the fact that there are no genuine point light-sources in practice. Even the sun on the firmament appears “disc-like” and is to be considered as a light cone with an aperture of half a degree. ⊕

Fig. 3.18 . . . and bring them into mutual rela- Fig. 3.19 Normal view of three convex polyhedra, including the shadow tion.

By subdividing a scene into convex parts, we can determine all surfaces that are entirely shaded (“dark”). The following important rule holds true for them: Faces that are entirely dark cannot receive additional cast shadows. This simplifies our work, which now concerns the determination of the shadows of the subdivided bodies on each other. We now have to consider: Two convex bodies never mutually cast shadows on each other. If there exist shadows in between them at all, then only one body casts shadows on the other.

Fig. 3.20 The detail shows the inflection points of the shadow boundary.

98

Polyhedra: multi-faced and multi-sided

⊕ Remark : This approach is a huge time-saver and can also prevent many possible errors. One can now derive a kind of priority list that, in most cases, is easily sortable: disregarding certain convoluted exceptions, there is always one “frontmost” building block on which no shadows are cast by other bodies. This is followed by the building blocks on which only the first body casts shadows, and so on. Even in the rare cases where the sorting of such a list is, at first, not possible, the challenge can be surmounted by dividing single (often very long) convex blocks into two separate ones. ⊕

▸▸▸ Acceleration of computer programs

If one considers all advantages that can be gained by subdividing a scene into convex partial bodies, then one can get fairly realistic images of complex scenes such as Fig. 3.21. This can prove to be important: for example, if one has to develop a “chess program,” which should primarily play in an intelligent manner, but in addition give the player a realistic image of the situation on the chess board, it would be a pity to waste much processing power on the highly realistic “rendering” of that image. A “real-time” visualization (at least thirty frames per second) is desirable and, in this case, easily achievable.

Fig. 3.21 Scenes composed of . . .

Fig. 3.22 . . . convex polyhedra

Fig. 3.23 Interpretation as full and hollow bodies

3.2 Convex polyhedra

99

In [3], I have described many computer algorithms that make such fast rendering of realistic images possible. Despite the age of the algorithms – especially by computer graphics standards – they still allow computer graphics fast as lightning with correctly calculated shadows. Even the scene in Fig. 3.22 (depicting the Commodore Amiga, a groundbreaking minicomputer in its day, but completely antiquated in our time) can be animated in realtime. The algorithms are a typical example of the fruitful application of theoretical geometric knowledge in other disciplines. ◂◂◂

Fig. 3.23 on the left shows complex, “rounded” polyhedra. The shadow boundaries of this body (on which all shadow polygons are based) are still comparatively simple. In Fig. 3.23 on the right side, the biggest polygons were removed from the polyhedron. This, of course, means that the polyhedron is no longer convex. At the same time, one may still derive some advantages from the fact that the “hull” of the polyhedron is convex: thus, either all faces potentially throw a shadow on the base plane, or none of them do. Furthermore, all front faces of the polyhedron are either completely illuminated or completely dark. Equipped with this knowledge, the rendering speed for the scene can be significantly increased.

Multiple light sources

Fig. 3.24 Penumbra shadows and umbra shadows of a convex object

Dealing with artificial light but also with regular sunlight and reflecting surfaces leads to penumbra shadows and umbra shadows: areas in penumbra shadows are illuminated by at least one light source each, or none at all. Areas in umbra shadows are not illuminated by any light source. The result may look complicated, but geometrically speaking, it can easily be accomplished by treating each light source “separately.” For convex bodies, one gets two or more convex shadow polygons. The umbra shadow lies where all polygons overlap. The other areas are more or less illuminated, depending on how many light sources are visible from their positions.

100

Polyhedra: multi-faced and multi-sided

What is true for convex polyhedra holds true for their refinements to smooth surfaces. In Fig. 3.25, for instance, one can see an elongated half-ellipsoid (Chapter 6) as part of a chandelier. The shadow outlines with respect to each light source are ellipses, which are convex curves. The penumbras are in general not convex. The area that is in shadow with respect to all light sources is convex.

Fig. 3.25 Penumbra shadows and umbra shadows of a convex object (half ellispoid)

▸▸▸ Shadow profiles One can analyze shadow casting of buildings during the day by calculating the shadows of the scene at regular intervals (e.g., each hour).

Fig. 3.26 Shadow profiles of a skyscraper (summer and winter half-year)

Fig. 3.26 shows how it can then be determined for how many hours single points remain shaded on any given day. Such questions are highly relevant during constructional changes in dense urban areas. ◂◂◂

101

3.2 Convex polyhedra

Fig. 3.27 By means of modern computer hardware, shadow profiles can be calculated within seconds. This is enormously useful for architects, who are, by law, obliged to make sure that their buildings do not cast too much shadow on their surroundings. Thus, it is possible to determine the shadow duration for each visible point in the scene (program development by Günter Wallner, www.uni-ak.ac.at/geom/schattenprofile/).

When do we speak of a polyhedron?

Fig. 3.28 Two of the three objects do not represent a polyhedron: For real polyhedra, all polygons must be closed, and two adjacent polygons in the plane are “merged”.

Fig. 3.28 shows some objects built with Geomag1 that are not polyhedra in the strict sense: Concerning the model on the left, the rotors of the helicopter are not polygons. Concerning the object in the middle, the base and top surfaces (regular hexagons) are divided into equilateral triangles that lie in one and the same plane. By “extending” the midpoints of the hexagons from the plane, we can construct a regular six-sided pyramid, whose side surfaces are merely isosceles and not equilateral.

Euler characteristic For closed polyhedra without “holes” – and therefore especially for convex polyhedra –, Leonhard Euler discovered a simple relation between the number e of vertices, the number k of edges, and the number f of faces: e+f = k +2. 1 Geomag

is the brand name of a toy construction system consisting of nickel-plated steel balls and connecting rods with a magnet on each end.

102

Polyhedra: multi-faced and multi-sided

For example, for the cube with e = 8 vertices, k = 12 edges, and f = 6 faces, we have 8 + 6 = 12 + 2.

Proof : An elegant and brief proof can be provided by applying the principle of mathematical induction, which is often useful in mathematics. The trick lies in proving the theorem for polyhedra from which we remove a face. We call this type of polyhedron “open”. The number of vertices and edges of a closed and open polyhedron are the same, whereas the opened one has one face less. Thus, it is to be shown that for open polyhedra we have e + f = k + 1. Let us first start the induction: The theorem is true for the simplest case, a single polygon (f = 1) with e vertices and as many edges. Now we show that the theorem is true for f + 1 faces if it is true for f faces: Let us assume that the Euler characteristic is correct for all open polyhedra of up to f faces. If this allows us to prove that the theorem is also true for open polyhedra with f + 1 faces, then this conclusion can also be applied to all f .

Fig. 3.29 Figure accompanying the proof

Let us consider an open polyhedron with f faces. Let us subdivide this object into two open polyhedra along an arbitrary, closed but non-planar polygon composed of m edges, exactly two of which should belong to the “top polygon” (Fig. 3.29). In sum, both parts still provide f faces, but there are m − 2 vertices and m − 1 edges more. For both partial polyhedra, according to the induction assumption, e1 + f1 = k1 + 1 and e2 + f2 = k2 + 1 hold true. This means (e1 + e2 ) + (f1 + f2 ) = (k1 + k2 ) + 2. Due to e1 +e2 = e+m−1, f1 +f2 = f and k1 +k2 = k+m−2, we get (e+m−1)+f = (k+m−2)+2 and thus, indeed, e + f = k + 1. ⊙

Fig. 3.30 Stellations of kites (middle picture: rhombic triacontahedron): 60 faces, 120 edges and 62 vertices

Fig. 3.30 shall serve as an example for Euler’s formula (in this case it is easiest to count the faces (12 ⋅ 5) and the edges (12 ⋅ 5 + 30 ⋅ 2).

103

3.3 Platonic solids

3.3 Platonic solids About 2500 years ago, the ancient Greeks started to classify spatial geometric bodies systematically. It seemed obvious to ask for all polyhedra with congruent faces and equal angles along the edges. Several of these were already known, and it was soon realized that only one was missing: the dodecahedron, which has twelve regular pentagons for its faces.

As simple as it gets The cube – a regular hexahedron – is the best-known example of a Platonic solid even though it does not have the minimum number of vertices, edges, and faces: It has eight vertices, twelve edges, and six congruent square faces. What makes the cube so simple is the fact that all of its edges are mutually perpendicular. It is, therefore, a special cuboid, and cuboids, from which many day-to-day objects are derived, are in any case easy to imagine.

Fig. 3.31 The shadow of a cube is a hexagon as a rule.

⊕ Remark : Fig. 3.31 shows a cube that is illuminated by two light sources. In general, a hexagon belongs to each light source in the shadow-receiving base plane. Both hexagons share four points as long as the cube is placed on the plane. The umbra shadow appears where they both overlap, and the penumbra shadow where only one of the hexagons affects the surface. In Fig. 3.31 on the right, one light source produces “grazing light”. In such exceptional cases, the shadow polygon is a rectangle if the light rays are parallel to a face of the cube. ⊕ ⊕ Remark : Pyrite (Fig. 3.32) is one of the most frequent sulfidic minerals in nature. It crystallizes in a cubic system and often occurs in the form of well-developed, cube-shaped crystals that exhibit characteristic streaks. Sometimes it also appears as a dodecahedron. ⊕

If a sketch of a cube is to be drawn, most people first draw a square and then attach four parallel line segments of equal length (but shorter than the edges of the square). This yields the vertices at the back, behind the square. Such a sketch is quite informative, even though cubes in nature cannot be visualized

104

Polyhedra: multi-faced and multi-sided

Fig. 3.32 Pyrite (“Fool’s gold”) with cuboid crystals

like this. It conveys what we know about the cube. A technical drawer would depict two squares above or next to one another and say: This is the front view, the other one is a top or a side view. This is even less ambiguous, though it may not be immediately apparent to a novice. Everyone understands it. Let us unfold the model of a cube into a plane. The result is often called the development of the cube. We now have the need to align the six squares in such a way that they occupy the least possible space (if, for instance, we wish to build many such cube models). Furthermore, it is our intention to minimize the number of edges that have to be glued together (i.e., the number of double edges in the unfolded model). If, as in Fig. 3.33, we only wish to develop the rest of the cube after a planar section, we have to be careful not to end up having several parts in our hands.

Fig. 3.33 Development of a cube including the planar section – badly chosen, since it “falls apart”.

Three objects from equilateral triangles There can only be one Platonic solid whose faces are equilateral quadrangles (or squares), because only three squares can meet in every vertex. If there were four, then 4 × 90○ = 360○ would complete the full angle, and the vertex pyramid would not be spatial anymore. This is the reason why we cannot assume equilateral hexagons as the faces of a Platonic solid: At least three faces meet at each vertex, and 3 × 120○ (the angle between two adjacent edges of a hexagon) already adds up to

3.3 Platonic solids

105

Fig. 3.34 Scenes of a development (tetrahedron, octahedron, cube)

360○ . Regular polygons with more than six edges are, thus, excluded from the beginning. Thus, we can only derive new Platonic solids from equilateral triangles and pentagons. Equilateral triangles (with angles enclosed by edges of 60○ ) offer three such possibilities: A spatial corner can be formed by three, four, and even five triangles. In all three cases, the sum of all angles in a corner is less than 360○ . If a vertex pyramid is formed by three triangles, then the polyhedron is already complete: This functions with four equilateral triangles in the form of a regular tetrahedron. Fig. 3.34 on the left shows how it can be constructed from its development.

Fig. 3.35 Scenes of a development (dodecahedron, icosahedron)

If a vertex pyramid is formed by four triangles, then we get the regular octahedron. Fig. 3.34 in the middle shows a possible development and the way it is folded. The octahedron can also be interpreted as a double square pyramid with the same base. Both pyramids have half of the diagonal of the base square for their height. If a vertex pyramid is formed by five triangles, then we get the regular icosahedron (from icosi =twenty). Fig. 3.35 on the right side shows a possible development and its reconstitution into a considerably complicated structure.

106

Polyhedra: multi-faced and multi-sided

Fig. 3.36 Platonic solids constructed by using Geomag. On the right: a regular icosahedron. The spheres and rods of Geomag are uniform in size, but not so in the image: The tetrahedron is slightly enlarged in comparison to the dodecahedron.

This concludes the possibilities of creating regular polyhedra from equilateral triangles. If our systematic approach is used, only one body remains where three regular pentagons (angle between edges of 108○ ) form a corner (3 × 108○ < 360○ ).

The last Platonic solid whose beauty defies description

Fig. 3.37 Development of a dodecahedron

Half a dodecahedron (from a pentagon = five vertices and dodecahedron = twelve faces) remains if one attaches a movable, congruent pentagon to each side of a regular base pentagon, and rotates the attached objects about the edges until a polyhedron emerges (Fig. 3.37 on the left). Two thus emerging, mirror-symmetrical dodecahedra fit together when one half is rotated by 36○ about the perpendicular axis (Fig. 3.37 on the right). Fig. 3.35 on the left shows a practical suggestion for the construction of a dodecahedron. The condition that all faces of a polyhedron have to be congruent is obviously very limiting. The frequent wish by architects that an arbitrary surface be approximated by small, congruent triangles (a cost-saving solution, see Fig. 6.53), already fails in principle: One always gets the edges of a small number of polyhedra, among which are the regular tetrahedra, octahedra, and icosahedra.

3.3 Platonic solids

107

Fig. 3.38 The “finished” dodecahedron in an oblique view and in the principal views

Fig. 3.39 stellated dodecahedron as a non-convex regular polyhedron (see also Fig. 3.58)

In practice, there exists a marginally useful cop-out: We abandon the necessity of convexity of the body and/or the faces themselves. It is then possible to obtain four additional types of Platonic solids: the star polyhedra. Fig. 3.39 shows these unusual structures that were discovered relatively late (by Kepler in 1615 and Poinsot in 1809). The “small stellated dodecahedron” – first described by Kepler – is constructed by twelve five-cornered stars (pentagrams) intersecting each other (Fig. 3.39 on the right). For better understanding, one of the non-convex pentagons is colored blue. In the case of the great stellated dodecahedron (Fig. 3.39 left), 20 three-sided pyramids stick on an icosahedron in such a way that we again obtain non-convex pentagons. Twenty regular triangles intersect one another on the great icosahedron (Fig. 3.39, middle left); twelve regular pentagons form the great dodecahedron (Fig. 3.39, middle right). Crafting a pentagonal dodecahedron is easy on a computer. Fig. 3.40 shows the “making of” a stable model. In practice – for example, when using the Geomag magnetic building blocks – it helps to “strengthen” the pentagons by inserting “panels.” Only five panels have been inserted on the left, and the construction is still not stable. A sixth panel (image center left) is required for the dodecahedron to be absolutely stable.

108

Polyhedra: multi-faced and multi-sided

Fig. 3.40 How many panels do we need to build a stable model of a pentagonal dodecahedron?

▸▸▸ Dualization of Platonic solids Due to their regularity, it is possible to inscribe an insphere and circumscribe a circumsphere for every Platonic solid. If such a polyhedron is polarized at such a sphere, then the vertices correspond to the faces of the polar polyhedron (and vice versa). The new polyhedron is once again regular. If the sphere is the insphere, then the faces correspond to their points of contact with the sphere and, thus, to their midpoints. The polyhedron that emerges from these surface midpoints is once again platonic!

Fig. 3.41 Polarization of the Platonic solid: The tetrahedron is self-dual, the cube is dual to the octahedron, and the dodecahedron is dual to the icosahedron.

The tetrahedron (4 vertices, 4 faces) is “dual to itself”. Cubes (8 vertices, 6 faces) and octahedra (6 vertices, 8 faces) form a dual pair, just as the icosahedron (12 vertices, 20 faces) and dodecahedron (20 vertices, 12 faces) do. ◂◂◂

Fig. 3.42 The five Platonic solids, and almost a sixth one

Fig. 3.42, once again, shows the Platonic solids next to each other. The surface of the sixth solid (third from the left) is ideally composed of ten equilateral triangles. (It can be divided into two five-sided pyramids.) However, the angles of the faces (edge angles) are not all equal.

3.4 Other special classes of polyhedra

109

3.4 Other special classes of polyhedra Archimedean solids

Fig. 3.43 Different Archimedean solids

A more generous condition that allows at least two different types of congruent surfaces presents many more possibilities (13 to 15 depending on more or less sophisticated counting). Fig. 3.43 shows several such solids that were already studied by Archimedes. The soccer ball is by far the most familiar Archimedean solid (or rather, a spherical variant of it). It can be “developed” from a dodecahedron and thus possesses 12 regular pentagons and 20 regular hexagons.

Fig. 3.44 Two Archimedean solids derived from a dodecahedron

▸▸▸ Tiling of space If the vertices of an octahedron are cut (Fig. 3.45 on the left), a new Archimedean solid that can be used to fill a space without leaving any gaps emerges.

Fig. 3.45 On the left: truncated octahedron (intersection with a cube). Center: exact tiling using such solids. On the right: tiling using irregular dodecahedra.

110

Polyhedra: multi-faced and multi-sided

Such tilings of space are not at all easy to accomplish when regular solids are used. It is impossible with the sole use of regular dodecahedra (see Fig. 3.45 on the right). The proof requires a calculation. Only quite recently (1993), it was discovered by Denis Weaire and Robert Phelan that irregular dodecahedra (with 12 faces) and tetradecahedra (with 14 faces) of equal volume – very similar solids possessing two hexagonal faces – can be arranged in groups of eight in order to fill space without leaving any gaps.2

Fig. 3.46 Tiling of space with irregular 12-sided and 14-sided solids according to Weaire-Phelan. On the left and in the middle, there are two views of the basic building block, composed of eight equal-volume polyhedra.

Fig. 3.47 More or less dense sphere packing in theory and practice

The easiest way to tile three-space is, of course, by using cubes. Spheres are not well-suited for this purpose. The gaps caused by spheres comprise almost half of the volume of the arrangement in Fig. 3.47: The ratio of the volume of a sphere to the volume of the circumscribed cube equals (4π/3) ∶ 8 ≈ 0, 52. The translation of the positions results in a slightly better utilization of space, but even in the optimal arrangement, it only covers about 3/4. In this case, nature reveals itself – as it so often does – to be rather pragmatic: A little bit of squeezing and shoving, and space is, once again, optimally utilized (see Fig. 3.47 on the right). ◂◂◂

2 More

information at http://en.wikipedia.org/wiki/Weaire-Phelan_structure or – in greater detail and with more emphasis on mathematics – http://torus.math.uiuc.edu/jms/Papers/ foams/forma.pdf.

3.4 Other special classes of polyhedra

111

▸▸▸ Different designs of a soccer ball

Fig. 3.48 Different soccer ball designs

Fig. 3.49 First row: design for the Champions league final in Munich, 2012. Second row: a design based on the cube.

Fig. 3.50 Other variations of a soccer ball

112

Polyhedra: multi-faced and multi-sided

The classic form of the soccer ball is derived from the Archimedian solid with 12 pentagons and 20 hexagons. Every once in a while a new soccer ball is designed (Fig. 3.48). Take a look at the, hopefully, self-explanatory series of images in Fig. 3.49. Fig. 3.50 shows some more variations. ◂◂◂

Rhombic polyhedra

Fig. 3.51 Left block: Five Platonic solids lead to two new interesting solids: the rhombic dodecahedron (12 faces) and the rhombic triacontahedron (30 faces). Right: Due to the fact that the rhombic dodecahedron can be generated by means of a cube, it follows that it is suitable for “packing space”

.Let us go back again to the Platonic solids, the faces of which are regular ngons. Through each edge e, we have a plane ε perpendicular to the connection of the edge with the center C of the solid (Fig. 3.51). All planes ε that contain the sides of a face form a regular n-sided pyramid. Two neighboring pyramids touch along a normal plane ε so that the two adjacent equilateral triangular pyramid-faces form a planar rhombus.

Fig. 3.52 Packing space with rhombic dodecahedra: a series of stroboscopic images during rotation

We would now expect five new solids that consist of as many congruent rhombuses as the adjacent Platonic solid has edges. However, it turns out that the cube and the octahedron (with 12 edges each) lead to the same result

3.4 Other special classes of polyhedra

113

– the rhombic dodecahedron (Fig. 3.51 upper middle and left). The same is true for the regular dodecahedron and the icosahedron (with 30 edges each). They generate the rhombic triacontahedron (triaconta = 30, Fig. 3.51 lower images). Finally, the regular tetrahedron with its six edges leads to a trivial result: the cube. In this case, the rhombic faces are squares.

Fig. 3.53 The projection of Platonic solids onto the circumsphere leads to three different remarkable rhombic tilings on the sphere.

Since a rhombic dodecahedron can be created from a cube and cubes can be stapled to fill space, we have found another non-trivial example of tiling space (application p. 109, Fig. 3.51 right). The upper images in Fig. 3.53 illustrate that the apices of the above-mentioned regular cones through the edges of the Platonic solids lie above the centers of faces. If we now project all points to the circumsphere, we get three different rhombic tilings of the sphere with 6, 12, and 30 congruent spherical rhombuses and 4 + 4 = 8, 8 + 6 = 14, and 20 + 12 = 32 grid points. We will learn more about the regular distribution of points on the sphere later on. ▸▸▸ More polyhedra consisting of congruent rhombuses? Fig. 3.54 on the left shows a polyhedron with 30 rhombuses (a somewhat “distorted version” of our rhombic triacontahedron) in the principal views. In the plan view, the sides of the rhombuses have equal length due to the fact that they have equal length in space plus their inclination is constant. Therefore, the height differences of all sides are constant (Pythagoras), and all vertices of the triacontahedron lie in equally distributed horizontal carrier planes (to be seen in the front view). In the plan view, the six rhombuses that appear as edges form a regular hexagon around the projection A′ of the apex A. Non-trivially, the six vertices 1′ , 2′ , 3′ , . . . of three connected rhombuses are also equally distributed on a circle c′ (drawn in red) through A′ . We could also take a circle, distribute six points A, 1, 2, 3, . . . equally, and define that these points have constant height differences. Then, we rotate the points six times about the vertical axis through A by 60○ and get a polyhedron consisting of 30 rhombuses.

114

Polyhedra: multi-faced and multi-sided

Fig. 3.54 Generalization of polyhedra consisting of rhombuses. The polyhedron on the left is a rhombic triacontahedron – its height can be varied by choosing the constant height difference of the horizontal carrier planes of the vertices.

This method can be generalized to get more vertices (Fig. 3.54 middle). If we only distribute four points on the red circle, we get a rhombic dodecahedron. Since the height differences can still be chosen, the polyhedron’s height can vary. Fig. 3.54 on the right shows a smoothened ornamental realization of the polyhedron shown in the middle. Later on, when discussing helices, we will once again come back to this example (application p. 324). ◂◂◂

Catalan solids In 1865, Eugéne Catalan described solids which are the duals of the Archimedean solids. The faces of a Catalan solid are congruent non-regular polygons (Fig. 3.55). The vertices and faces correspond to faces and vertices of the dual type.3 Once again, we encounter pure rhombic solids: the already well-known rhombic dodecahedron and the rhombic icosahedron (20 faces).

3 http://en.wikipedia.org/wiki/Catalan_solid

the solids.

provides a good survey and all the names of

3.4 Other special classes of polyhedra

115

Fig. 3.55 Polarization of Archimedean solids at a sphere around the center. Six (blue-shaded) Archimedean solids result in (yellow-shaded) solids with congruent triangles, two (gray-shaded) result in solids with congruent rhombuses, and the four orange-shaded ones result in polyhedra with congruent pentagons or quadrilaterals.

▸▸▸ Folding

Fig. 3.56 One of the stelae of the University of Applied Arts Vienna (Oliver Kartak)

Stelae (standing slabs) are sometimes used as landmarks. For the University of Applied Arts Vienna (Fig. 3.56) the designer created staelae that resemble origami. This Japanese art of paper folding is a process by which a flat square

116

Polyhedra: multi-faced and multi-sided

or rectangular sheet of paper is transformed into a specific shape or sculpture through folding and sculpting techniques.

Fig. 3.57 A crease pattern in accordance with the theorem of Kawasaki

Fig. 3.58 Similar origamis: On the left we see birds made by my daughter Sophie, on the right two great stellated dodecahedrons put together.

A criterion for an origami construction to be flat is given by the theorem of Kawasaki. It states that a given crease pattern can be folded into a flat origami if the angles α1 , α2 , . . . in the crease points fulfill certain simple conditions (we will not go into detail here, Fig. 3.56 shows a practical example). The folding process is illustrated in Fig. 3.57, and the designer of the metal

3.4 Other special classes of polyhedra

117

stele in Fig. 3.56 did also use this theorem in order to fold the stele from a flat piece of metal. The practice of folding origami is very advanced, sometimes rather magnificent. On the Internet one can find a lot of different instructions for the creation of remarkable sculptures out of paper. Fig. 3.58 shows two examples. The picture to the right shows two great stellated dodecahedrons of different size (see Fig. 3.39). Since they are similar, it is possible to stack the smaller one on top of the other. ◂◂◂ ▸▸▸ Foldable flower vases and pots (Fig. 3.59)

Fig. 3.59 Smoothly adjustable flower vases made of Tetra Pak carton

Packaging material can be waterproof (Tetra Pak carton packages). Steffen Kehrle has used such material to design “adjustable” vases, which can be opened and closed quite smoothly – almost like a flower – by means of a ◂◂◂ simple elastic band.

118

Polyhedra: multi-faced and multi-sided

3.5 Planar sections of prisms and pyramids General pyramids are constructed by connecting a polygon that is not necessarily planar with a fixed point (the apex of the pyramid). If the apex is a point at infinity, then we speak of a prism.

Fig. 3.60 From the spatial situation to a construction in the plane: parallel perspectivity

If we intersect a prism or a pyramid with two arbitrary planes ε and ε which intersect all edges but do not contain the apex, then both intersected figures are related by central perspectivity (in the case of a pyramid) or parallel perspectivity (in the case of a prism). When (spatial) parallel perspectivity is interpreted in a parallel projection (e.g., on drawing paper), it represents perspective affinity. Accordingly, spatial central perspectivity appears in the image as perspective collineation. With parallel perspectivity (Fig. 3.60) and central perspectivity (Fig. 3.62), corresponding points lie on parallel perspectivity rays or perspectivity rays through the apex. Corresponding sides of the section polygons intersect each other on the straight intersection line a = ε ∩ ε: The respective face ϕ of the prism or pyramid intersects ε and ε along the straight carrier lines ε ∩ ϕ and ε ∩ ϕ of the respective edges, and these have to pass through the intersection point ε ∩ ε ∩ ϕ = a ∩ ϕ. The straight line a is called the axis of perspectivity.

3.5 Planar sections of prisms and pyramids

119

Fig. 3.61 Perspective affinity of two point fields

If one planar section polygon of a prism or a pyramid is known, then each further section can be determined very efficiently by just using the axis a of perspectivity and only one point of the new intersection. It is then possible to restrict oneself to a “two-dimensional” construction: Let P1 Q1 be an edge of the first section figure and P2 the already known point on the edge through P1 . Q2 can then immediately be determined since P1 Q1 and P2 Q2 intersect on a. This construction works for each projection and is truly two-dimensional. It is even possible to free oneself from spatial interpretation and to define the following: If two planar connected fields of points are related in such a way that corresponding points lie on rays that are either parallel or pass through a fixed center, and if additionally the corresponding connecting straight lines of two points intersect on a fixed axis a, then the relation is a planar perspective affinity or a planar perspective collineation. The connecting rays of the corresponding points are called the rays of affinity or rays of collineation. The axis is called the axis of affinity or axis of collineation, and the center is called the center of collineation. ⊕ Remark : The connecting straight lines of respective points pass through a center, which may also be a point at infinity. The points are “mutually related via perspective.” This concept was already mentioned in connection with Kiepert’s Theorem (p. 19). Therefore, one speaks of perspective affinity and collineation. ⊕

The preservation of affine ratios and parallelity further applies to perspective affinity: This follows from the two aforementioned properties (assigned points

120

Polyhedra: multi-faced and multi-sided

Fig. 3.62 From the spatial situation to a task in the plane: central perspectivity

Fig. 3.63 Spatial perspectivity can be applied to all views. The parallel projection on the left and the central projection on the right show how parallel lighting is imaged. The left image shows a planar perspective affinity, the right image a perspective collineation.

lie on parallels, assigned straight lines intersect on the axis of affinity) and from the intercept theorem. In this way, the following entities are perspectively affine / collinear in space during each parallel projection / central projection: • two planar sections of a prism / pyramid; • each planar polygon and its parallel / central projection in a plane; • each planar polygon and its parallel shadow / central shadow on a plane. • each planar polygon and its parallel shadow / central shadow on a plane. In anticipation of the next chapter, prisms / pyramids can also be “refined” by choosing a base curve instead of a basal polygon. In such cases, the following entities are perspectively affine / collinear:

121

3.5 Planar sections of prisms and pyramids

Fig. 3.64 Perspective affinity (space) ↦ perspective collineation (plane)

• Two planar sections of a cylinder / cone.

Fig. 3.65 The affine relation between a circle and an ellipse (de la Hire’s construction, sometimes called the Proklus construction, uses this fact and is indirectly illustrated in Fig. 11.12 on the right.)

⊕ Remark : Mathematically speaking, an affine relation between two fields of points P (x, y) and P ∗ (x∗ , y ∗ ) is expressed by a linear relation between the respective coordinates: x∗ = A x + B y,

y∗ = C x + D y

(A, B, C, D ∈ R).

In matrix notation [9], one writes p∗ = M ⋅ p. This mapping is invertible if, and only if, M is invertible. Thus, p = M−1 ⋅ p∗ , while M−1 is the inverse matrix of M. ⊕

This enormous range of potential applications explains the importance of perspective affinities and perspective collineations. We will prove, for instance, that an arbitrary planar section of a cylinder of rotation is an ellipse (p. 164). On the other hand, the base curve of a cylinder of revolution is a circle. Therefore, we have: Circle and ellipse are mutual affine images.

122

Polyhedra: multi-faced and multi-sided

Fig. 3.65 on the left shows the affinity of an ellipse to its principal apex circle, and on the right its affinity to its auxiliary apex circle. E π

g =π∩γ

γ E′ e

hc

p h

pc

ec eye point E, image plane π, base plane γ axis of collineation g = π ∩ γ yellow circle e ⇒ image ellipse ec red circle p ⇒ image parabola pc blue circle h ⇒ image hyperbola hc

Fig. 3.66 The collinear relation between a circle and the three types of conic sections, see also the general case with a non-perpendicular image plane (Fig. 9.24).

Fig. 3.66 can be seen as an anticipation of Chapter 9: If circles (e, p, and h) in a plane γ are projected from a center (the eye point E) to an image plane π, we get conic sections (ec , pc , and hc ) after the intersection with the quadratic projection cones. These can be ellipses, parabolas, or hyperbolas.

Fig. 3.67 The water basin in front of St. Charles’ Church in Vienna. Depending on whether the plane parallel to the sensor plane through the lens center touches its boundary, intersects it, or not, we get an ellipse (left), a parabola, or a hyperbola (right).

In every case, the central perspectivity in space appears as a perspective collineation in the drawing plane. The image of the straight line g of γ and

3.5 Planar sections of prisms and pyramids

123

π is the axis of collineation. The image of the center E is the center of collineation. Any intersection of the circles with their projections in π lies on the axis of collineation. Since π and γ commute, i.e., it does not matter which comes first, the aforementioned is true not only for the circle but for all conic sections. It is, thus, possible to “change” a hyperbola or parabola into an ellipse and even (in the special case) into a circle by means of perspective collineation. Fig. 3.67 is an example of the perspectively collinear mapping of an ellipse – after all, a photograph produces a kind of collinear mapping!

Fig. 3.68 “Heidelberg horse”: How many conic sections (or parts of which) are visible on both photos? Hint: All boundary curves on the horse, and on its neck in particular, are circular arcs. You may stop counting once you have found 3 hyperbolas and 20 ellipses . . .

Fig. 3.68 shows two photos containing a multitude of conic sections in the form of collinear images of circles and ellipses: The left mainly contains images of circles (the circle-shaped boundaries of the horse’s neck are depicted as parts of hyperbolas), but also elliptic shadows on the cylinders of revolution contained in the building. On the right, there are elliptic conic sections that also appear in the photo as ellipses. ▸▸▸ A flexible interactive installation from an Archimedean solid

Fig. 3.69 Kinetic Architecture: Guvenc Ozel (with Alexandr Karaivanov, Jona Hoier, Peter Innerhofer). The inside has a flexible triangular mesh (http://ozeloffice.com/).

124

Polyhedra: multi-faced and multi-sided

The final example in this section does not relate to the truncated octahedron but to another Archimedean solid (Fig. 3.44 on the right): “Cerebral Hut” explores the relationship between architecture, motion, and human thought. We traditionally assume that an artificial environment influences our psyche. What if a kinetic piece of architecture could establish a direct connection between the thoughts of its user and itself in order to reconfigure its physical boundaries accordingly?

Fig. 3.70 In order to create a space that is reactive to brain activity, the team hacked and reprogrammed a commercially available device that can measure concentration levels and blinking, interpreted these data thresholds, and wrote scripts that would translate them into motion.

Research on different folding patterns and geometric structures has led to the creation of an environment that can act as a vessel for motion. Cerebral Hut plugs into a vein of contemporary research that explores kinetic environments and the relationship between technology, motion, and space, but it is the first of its kind that creates a moving piece of architecture that directly responds to human thought.

Fig. 3.71 The biosphere by Buckminster Fuller (Montreal)

A remark from a geometrical point of view: The triangulation of the biosphere in Montreal (Fig. 3.71) is comparable to the (flexible!) triangulation used in the installation. Cerebral Hut has no final or ideal design form. Its interior and exterior are in constant transformation, which is triggered by user participation. ◂◂◂

4

Curved but simple

In this chapter, we shall discuss the theory of curvature of planar and space curves as well as basic curved surfaces that are easy to imagine, such as spheres and cylindric surfaces. The latter differ substantially in one respect: The sphere is “doubly curved” while cylinders are just “single curved.” We will first talk about the sphere, despite its double curvature, because it is very easy to define and imagine. The sphere plays a central role in further geometric considerations. Every planar section of a sphere and also the intersection of two spheres is a circle. We first need to understand the theory of planar and space curves. In space, we have two kinds of curvature, namely curvature and torsion. By using curves, we can create surfaces. The sphere may be generated by rotating a circle about one of its diameters. Cylindric surfaces can be generated from straight lines that are moved parallel to a certain fixed direction through space. The images of all possible curves on a surface envelop the contours of the surface. If this contour only consists of straight lines for every projection, the surface is developable. It is only such surfaces that can be unfolded (developed) into the plane without distortion. The planar section of a cylinder of revolution is an ellipse (in general), and its development is a sine curve. The intersection of two cylinders of revolution is usually a space curve, but it may in special cases split into two ellipses. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_4

125

126

Curved but simple

4.1 Planar and space curves Every branch of science has its own language by means of which its ideas can be expressed clearly and concisely. Before discussing curved surfaces, let us, therefore, define certain terms that are particularly important in differential geometry.

Basics from planar curve theory Differential geometry deals with properties of curves and surfaces that describe them independently of parametrizations and coordinate systems such as tangents, curvatures, etc., which can be calculated by means of mathematical differentiation. For instance, if one considers two points P and Q of a planar curve, then its connection line forms a secant (lat. secare = to intersect). If Q now moves closer to P , then there exists an unambiguous limiting position which is called tangent to the curve (lat. tangere = to touch). One simply says: At the point of contact P , the tangent of a curve and the curve share two points which are infinitely close together. The normal to the tangent at P is called the curve normal. If the curve is a circle, all curve normals pass through the center. However, in general, the totality of normals to the curve envelops a curve – the so-called evolute.

Fig. 4.1 Tangent, normal, evolute of different curves

We can also consider two neighboring points Q and R to the curve point P . If the three points do not lie on a straight line, they define a circle. We now let Q and R move closer to P . This eventually leads to a well-defined limiting position of the circle determined by three points – the osculating circle at the point P . (A circle can also degenerate into a straight line or a point.) The radius of the osculating circle is called the radius of curvature. In the vicinity of the curve point, it approximates the curve much better than the tangent. The osculating circle at P is said to have three points in common with the curve.

4.1 Planar and space curves

127

The locus of the midpoints of all osculating circles is the evolute enveloped by the curve normals. Proof : The osculating circle is determined by three neighboring points P , Q, and R. So, its center is located at the intersection of the perpendicular bisectors of P Q and P R. Let Q∗ be the midpoint of P Q and R∗ that of P R. The perpendicular bisectors, therefore, converge towards the curve normal in Q∗ R∗ . The circumcenter of P QR thus converges towards the intersection of two adjacent curve normals. ⊙

▸▸▸ A circle as an evolute Fig. 4.1 shows curves with their evolutes. One can see that evolutes have cusps whenever the curve has an apex – a point whose radius of curvature is stationary. The right curve is especially notable. It is constructed in such a way that their evolute is a circle. It is, therefore, called a circle’s involute. ◂◂◂ ▸▸▸ Osculating circles of the ellipse

Fig. 4.2 Evolute and osculating circles of an ellipse

In Fig. 4.2, the evolute of an ellipse is visible – a diamond-shaped curve with four cusps at the centers of the osculating circles at the apices of the ellipse. The figure also illustrates how to construct the osculating circles of the apices, which are very useful when we draw an ellipse. ◂◂◂ ▸▸▸ A curve can be its own evolute In Fig. 4.3, one can see logarithmic spirals with their evolutes. These are curves that traverse a pencil of rays under a constant angle ψ. Their equation in polar coordinates (r, ϕ) is r = ep⋅ϕ . The constant parameter p = cot ψ determines how fast the logarithmic spiral wraps around its asymptotic point. The evolute of such a curve is another logarithmic spiral that is congruent to the initial curve if p is chosen appropriately. In special cases, it can even be equal to the initial curve (right image). Logarithmic spirals play an important role in nature because they are related to exponential growth. They also have their place in technology: The photo in Fig. 4.4 shows a paving slab lifter. Due to the weight of the object being

128

Curved but simple

Fig. 4.3 Logarithmic spirals with their evolutes

Fig. 4.4 Logarithmic spirals in technology

lifted, the spirals are pressed towards the bottom, transmitting the pressure back to the slab. ◂◂◂ ▸▸▸ We steadily rotate the steering wheel

Clothoid with winding points: The radius of curvature decreases proportionally to the arc length which makes the image look so balanced. Fig. 4.5

129

4.1 Planar and space curves

The reciprocal value of the radius of curvature is called the curvature of the curve. The distance of two points, measured along the curve, is called arc length. Fig. 4.5 shows a so-called clothoid. It is characterized by the fact that the curvature increases linearly with the arc length. Thus, the radius of curvature decreases proportionally to the arc length. Clothoids are applied in road and railway construction, where a constant rotation of the steering wheel makes it possible to change a straight path into a circular one with curvature continuity. The equation of the curve (it requires the numerical solution of integrals) is given in [9]. The curve wraps around two points ◂◂◂ (asymptotic points) in an infinite number of loops. ▸▸▸ Envelopes of circles

c E

E

c

Fig. 4.6 Envelopes of circles centered on a curve c that contain a fixed point E

c c∗

E∗ n P

c∗

t E

E

t

c n E∗

Fig. 4.7 The envelopes c∗ are orthonomic curves of c with respect to E.

Motivated by Fig. 4.5, let us define a transformation as follows: Take a planar curve c and consider the set of circles in the plane centered on c that contain a fixed point E. What is the envelope of all circles? Fig. 4.6 shows two

130

Curved but simple

“educated guesses”: When we take a circle or an equilateral hyperbola as c, the results look familiar (a limaçon of Pascal and a “lemniscate of Bernoulli” (Fig. 4.6). How can we find the envelope of the circles in a pointwise manner? For this purpose we have to intersect two neighboring circles. Since, by definition, one of the intersection points is always E and the other one lies on the normal n of the connection line of the two neighboring centers of the circles – and this connection line is the tangent t of c (Fig. 4.7). So, the points E ∗ of our desired curve c∗ are symmetric to E with respect to the tangents of c. Such curves are called “orthonomic curves”. The variety of orthonomic curves is great, since we can choose both the curve c and the position of E. Clearly, the less the degree of c, and the more special the point E that is chosen, the ◂◂◂ more specific the curves c∗ . ▸▸▸ Polarizing curves In Chapter 1 we introduced polarity at a circle (Fig. 1.37). Points correspond to straight lines and vice versa. Polarization of a curve c at a circle k was done as follows: The tangents t of c are transformed into the points T ∗ of the resulting curve c∗ . The points P of c result in the tangents p∗ of c∗ (Fig. 1.41). Conics, for instance, are transformed into conics again. c

c∗

c c

∗

T∗

k P

p∗ t k

t P

p∗ T∗

Fig. 4.8 Different spirals obtained by polarization at a circle: The left side shows a hyperbolic spiral c (polar equation r = a/u) which is transformed into an involute of a circle c∗ , on the right we see another logarithmic spiral c which remarkably results in a reversely congruent logarithmic spiral c∗ .

Fig. 4.8 shows two more special cases: If we polarize a hyperbolic spiral at a circle around the spiral center, we get an involute of a circle (see also Fig. 4.11). The second example is especially noteworthy, since it illustrates that the logarithmic spiral does not change its shape when it is polarized at a circle around its center. ◂◂◂

131

4.1 Planar and space curves

▸▸▸ Offset curves The offset curve c∗ of a curve c at distance d is a curve that always has the same normal distance d from c (Fig. 4.9). The curves c and c∗ can then also be called “parallel curves”. All parallel curves have the same evolute. If an offset curve hits the evolute, is must have a cusp since then the osculating circle has radius zero.

c

Fig. 4.9

Offset curves of a given curve c.

c

Fig. 4.10 Involutes of a circle c and their congruent (!) offset curves

Usually offset curves with signed distance d differ for positive and negative distance. This does not apply any more if the curve c has a cusp. As an example take the involute of a circle (Fig. 4.11). This curve is the only one out of all curves whose offset curves are of the same type. They even are congruent! ◂◂◂

132

Curved but simple

c

Fig. 4.11 Offset curves in practice. Left image: tracks of a marine snail feeding on jelly fish on the beach. Right image: a basket, where the curve in the middle closely resembles an ellipse.

Fig. 4.12 Planar curves provide a source of inspiration to artists (Greg Lynn, “St.Gallen”).

▸▸▸ Architectural design using curves Fig. 4.12 shows a virtual architectural design (“Intricate Surface”) with a number of planar intersection curves that obey certain rules that the artist has developed (“mutations”). ◂◂◂

4.1 Planar and space curves

133

The theory of space curves

Fig. 4.13 Almost two-dimensional curves . . .

If the curve does not lie in a plane, then the whole issue becomes more challenging. The terms secant and tangent do not change their meanings. The curve normal, however, is no longer uniquely defined: Each normal to the tangent through the point of contact is a curve normal and lies in the normal plane ν of the curve tangent.

Fig. 4.14 Osculating circles of a space curve

In space, we can also consider a curve point P and two neighboring points Q and R. If the three points do not lie on a straight line, they define a circle in space. If we now let Q and R move towards P , the osculating circle of the

134

Curved but simple

curve at the point P converges to a limiting position. Its carrier plane is called the osculating plane. We say: The osculating plane shares three (infinitely close) points with the curve at the point of contact.

Fig. 4.15 Accompanying tripod (also called Frenet frame) of a space curve

Among all normals of the curve at the point P , we can now highlight one normal in particular – the one that lies in the osculating plane, also called the principal normal. If we now consider the normal that lies perpendicular to the osculating plane (the so called binormal ), then we have finished the curve’s accompanying tripod. ⊕ Remark : All osculating planes σ envelop the tangent surfaces of the curve, which we will discuss in detail later. All normal planes ν of a curve envelop a surface called normal developable. In Fig. 4.37 on the right side, we see an example of such a surface. More interesting for us is a surface that is enveloped by the so-called rectifying planes. The rectifying plane ̺ is spanned by the curve tangent t and the binormal b (Fig. 4.15 on the right). The thus resulting surface is called the rectifying developable. It occurs, for example, in twisted paper strips (Fig. 5.60).

Fig. 4.16 Special projections of a curve

⊕

The normal projection of a curve to the osculating plane σ in P is a planar curve that has the same osculating circle in P ′ = P as the space curve itself (Fig. 4.16, left). When projected orthogonally to the rectifying plane ̺,

4.1 Planar and space curves

135

the curve has (as a rule) an inflection point P ′′ = P . (The osculating circle appears as a straight line; Fig. 4.16, middle.) In the case of so-called handle points – points which may be found in a symmetry plane of a curve – a flat point occurs. When we finally project orthogonally to the normal plane ν (Fig. 4.16, right), a cusp P ′′′ = P occurs because the curve tangent appears as a point. In the application on p. 142, we will discuss the shortest curves (geodesic lines) on curved surfaces as applications of the aforementioned topics.

Fig. 4.17 Torsion of a space curve and something akin to an accompanying tripod

Apart from the curvature, geometry also employs the notion of the torsion of a curve (Fig. 4.17). Circles (seen as space curves) have constant curvature but zero torsion. Helices as “generalized circles” also have constant curvature, but they additionally have constant torsion. The torsion at a curve point is a measure of the rate at which the osculating plane rotates about the tangent (by analogy with the curvature of a planar curve, which is a measure of the rate at which the tangent rotates about the center of curvature). A curve with zero torsion lies in a fixed plane, which is the osculating plane (by analogy, a planar curve without curvature remains in the direction of a straight line, which is the tangent). ▸▸▸ The simplest space curve Perhaps, the one example of a space curve that is the simplest to understand, is the helix, which will be discussed in greater detail in Chapter 7. In a helical motion (a composition of a rotation and a proportional translation along the rotation axis), the helix constantly winds along the axis of a cylinder of revolution. Therefore, curvature and torsion are the same in each point of the curve, and all the tangents and osculating planes enclose the same angle

136

Curved but simple

Fig. 4.18 A photo of a helix inside of a LCD-lamp

to the axis of the cylinder. Projected in direction of its axis, the helix appears as a circle. Any projection perpendicular to the axis is a sine curve. Fig. 4.18 shows a photo of a helix, i. e., a perspective image. Fig. 4.19 illustrates that such curves also occur in nature.

Fig. 4.19 A helix-like space curve in nature

Fig. 4.20 A helix (gray/green) is polarized at a sphere centered on its axis. In this special projection perpendicular to the axis, the helix appears as a sine curve. The polarized curve (red/yellow) lies on a cone of revolution.

4.1 Planar and space curves

137

In Fig. 4.20 (and also in a general view in Fig. 1.42) such a helix c is polarized at a sphere centered on the axis. Its osculating planes σ will result in the points S ∗ of the polarized curve c∗ . The radial rays leading to the points S ∗ are perpendicular to σ and thus also have a constant angle to the axis. Consequently, c∗ lies on a cone of revolution. Furthermore, the distance of σ increases linearly with the rotation angle u during the helical motion. Since in the polarity transformation the product of the distances of the plane σ and its pole S ∗ is constant, the curve c∗ appears as a curve with polar equation r = a/u (a is a constant), which is a hyperbolic spiral (Fig. 1.42 on the right). ◂◂◂

Space curves can create surfaces If a curve moves through space (during which its form may change), it usually “sweeps” a surface. The different positions of the curve are called u-lines. The orbits of the curve’s points form a second set of curves on the surface, the vlines (Fig. 4.21). In general, only one u-line and one v-line pass through each surface point P . The tangents tu and tv at P to both lines span a plane τ which touches the surface at P and is called the tangent plane. The normal n of the tangent plane P is called the surface normal.

Fig. 4.21 Tangent plane, surface normal, and u- and v-lines of a surface

Contour and outline of a surface Let us view a curved surface from a point E (in Fig. 4.22, it is a point E∞ at infinity). Then the contour of the surface is usually seen immediately. It is the locus of certain points on the surface that form the contour line k. Let K be a contour point. It is defined such that the viewing ray EK touches the surface, and therefore, lies in the tangent plane τ of K. This means that it is perpendicular to the surface normal n. Let us formulate the following important theorem: In a contour point, the viewing ray is orthogonal to the surface normal. The tangent plane at the contour point goes through the projection center.

138

Curved but simple

Fig. 4.22 Contour point, contour on the surface, and outline of the surface in a projection plane

Fig. 4.23 Rather tricky contour of a snail shell: The surface outline (black and red) is enveloped by the images of arbitrary surface curves. Note that boundary lines are not part of the outline.

In the projection to an image plane π, the surface – apart from potentially occurring boundary curves – is bounded by the projection k p of the contour line (the outline). The outline is also enveloped by the projections of all possible surface curves. The following theorem is especially important for geometrically correct freehand drawing: If a curve on a carrier surface intersects the contour of the surface, then, in general, its projection touches the outline of the surface. Only in exceptional cases, the projection cp of a surface curve c has a cusp on the outline – namely, when the projection center E lies on the tangent of c at the intersection with the contour (Fig. 6.93).

4.1 Planar and space curves

139

▸▸▸ Why do highlights occur on curved surfaces? The basic geometric assumption is as follows (Fig. 4.24): A point R of

Fig. 4.24 Highlights in different surfaces. Left: one light source (the Sun). Right: reflections of different non-point light sources (flashlights).

an illuminated surface is a highlight when the projection center Z and the light surface L lie in the same plane through the surface normal n in R. An additional restricting condition says that n must be the angular bisector of LR and ZR. Fig. 4.24 shows highlights on spherical surfaces. The highlights lie in planes that include the respective centers of the spheres, the position of the light source, and the lens center of the camera. ◂◂◂

How can the curvature of a surface be measured? The term surface curvature is much more complicated than the simple curvature of a curve: By merely considering the normal sections of the surface at a surface point P as in Fig. 4.21 on the left (these are the surface curves through P in a plane through the surface normal n), one deals with an infinite number of curvatures of curves through P .

Fig. 4.25 Elliptic, parabolic, and hyperbolic surface points, flat point (bottom right)

Even with the diversity of curved surfaces, three significantly different types of surface points can be distinguished. For this purpose, let us consider the surface in such a way that P is the contour point (the projection center lies

140

Curved but simple

in the tangent plane of P ). If the surface now lies in a sufficiently small neighborhood of P on both sides of the tangent plane, then we speak of a hyperbolic point (Fig. 4.25 bottom left). Each saddle surface possesses points which are exclusively of this type. If the surface touches the tangent plane at one side, then we speak of an elliptic point (top left; a typical example is the sphere). If there exists a certain surface curve (or tangent) through P along which the surface, only considered locally, remains completely in the tangent plane, we speak of a parabolic point (in Fig. 4.25, top right, we see how a tangential section “forms a cusp” at the point). Cylinders and cones represent this type particularly well. A fourth type can only happen singularly or alongside a curve on the surface: Fig. 4.25, bottom right, shows a so-called flat point. This differentiation has great practical implications. Surfaces which consist only of parabolic points (including some flat points) are the easiest to modify. What is more, they can typically be unfolded (“developed”) into a plane. Hyperbolically curved surfaces are much harder to modify than even elliptically curved ones. Both elliptically and hyperbolically curved surfaces cannot be developed, which is especially impractical in the case of the sphere: There is no way of mapping the surface of the Earth into the plane without distortions.

Polygon mesh on a sphere While spheres can be approximated more or less well by many quadrangles or triangles (the facets of insect eyes are also congruent, as can be seen in Fig. 4.26 on the right), not all faces will be mutually congruent. Fig. 4.27 shows a not-quite-perfect distribution of triangles. This triangulation can be derived by the “refinement” of an icosahedron.

Fig. 4.26 Left: simulation of a compound eye, derived from a refined icosahedron as triangle mesh (Fig. 4.27). Spheres with a suitable radius are placed in the triangle’s centroid. These spheres intersect each other and form polygon patterns that usually consist of hexagons and sometimes also pentagons. Right: for comparison, the eye of a robber fly.

▸▸▸ A moderately equal distribution of points on the sphere The problem of evenly distributing a given number n of points on the surface

4.1 Planar and space curves

141

Fig. 4.27 Refinement of an icosahedron

of a sphere is only exactly solvable if we have 4, 6, 8, 12, and 20 points, because in these cases, Platonic solids are formed in the following sequence: tetrahedron, octahedron, cube, icosahedron, dodecahedron. Based on these solids, the pattern may be “refined” as in Fig. 4.27, thus allowing for multiples of the aforementioned numbers.

Fig. 4.28 10, 15, 64, and 250 points distributed uniformly on the sphere

Fig. 4.28 illustrates a possible solution for other numbers of points. The solutions were calculated by using a dynamic approach that employs quasiphysical repulsion for the points. The shortest distances between the points are parts of great circles on the sphere (see p. 143), and the repulsive forces increase and decrease by the square of the distance. The translation of the points on the surface continues until a state of equilibrium is reached. The algorithm was developed by Franz Gruber based on the ingeniously simple algorithm by Fruchterman/Reingold [2]. This problem is also known as the Thompson problem, which is concerned with the minimization of energy of n equal point charges on the sphere. ◂◂◂ ▸▸▸ Triangulation as a powerful tool Triangulation is of high importance in the computer age: It is not only useful for the approximation of surfaces but also for the simplification of complex geometric volumes. Many particularly difficult physical problems can be solved with adequate accuracy by breaking down the situation into partial problems.

142

Curved but simple

Fig. 4.29 A tilted brandy glass and a weaving ashtray

Fig. 4.29 on the left shows how a body is first cut into sections – in this case, it is a fictitious brandy glass. The emerging intersection curves can be highly complicated (closed) line strips that may also have an arbitrary number of holes. In the second step, these sections are triangulated (subdivided into triangles) and can thus be interpreted as volumes (three-sided prisms with the thickness of a disc). For each prism, the centroid, the statical momentum, and the rotational momentum regarding arbitrary axes (see [9]) can be determined by using simple formulas. The sum of all centroids is called the total centroid (in the picture, it is marked red). The sum of all rotational moments is called the total rotational momentum.

Fig. 4.30

Some complications arise with the introduction of fluids . . .

Realistic physical simulations can be accomplished in this way. For instance, it is conceivable, given the right impulse, that the ashtray in Fig. 4.29, right, can set itself upright from its seemingly hopeless situation. When simulating fluids (Fig. 4.30), however, simple geometry is no longer sufficient due to the complexity of the situation. ◂◂◂ ▸▸▸ Geodesic lines – the shortest connection If two points on a curved surface need to be connected by a surface curve of minimal length, this will (in general) not be a straight line. We shall discuss this problem particularly in relation to the sphere and the shortest connecting line in this special case (application p. 159, Fig. 4.32 on the right). Let us first define the following: A geodesic curve on a surface is characterized by the fact that in all of its points, the respective osculating plane includes the surface normal.

4.1 Planar and space curves

143

Fig. 4.31 Art work with curved approximations to spheres (Kyoto): Bending straight sticks creates great circles on the sphere (see also Fig. 4.32 on the right).

This leads to the following: The shortest connection between two points in a surface is a geodesic curve on the surface. At this stage, let us not proceed with a mathematically rigorous proof but merely make the matter more plausible: By definition, all principal normals (Fig. 4.15) of a geodesic curve are at the same time normals of the carrier surface. Let us now consider two neighboring points Q and R of a surface point P . In the normal projection to the tangent plane in P , the surface curve is approximated by the normal projection of the osculating circle – it is a straight line because the osculating plane is its carrier plane. In other words: Locally speaking, the curve works like a straight line – which, as we know, is the absolutely shortest path. Every other connection from Q to R would be a detour. ⊕ Remark : For two special cases, there exists a simple and easily applicable solution: Geodesic lines on spheres are great circles. Geodesic lines on developable surfaces become straight lines in the unfolding. First of all, let us consider the sphere: The osculating plane of the surface curve has to contain the surface normal and must, therefore, pass through the center of the sphere. Thus, the osculating circle at every point is a great circle. If the geodesic curve were to deviate from the great circle, then the osculating plane would “sway,” which would lead to a contradiction.

144

Curved but simple

Fig. 4.32 Left: geodesic lines on a general surface. A “right triangle” has been drawn in – however, the Pythagoraen theorem only applies if the surface is developable. Right: Geodesic lines on a sphere are great circles.

Now let us take a look at developable surfaces: Unfolding preserves lengths, and in the plane, the shortest connection between two points is a straight line. Fig. 4.88 shows geodesic curves on a cylinder of revolution that result from the bending of straight lines. These are helices, which we shall discuss further in Chapter 7. ⊕

◂◂◂

How can we recognize a developable surface?

Fig. 4.33 Straight contour parts of developable surfaces must be visible from all directions.

If a surface is parabolic at every point P , then it also has, by definition, a tangential direction in P along which the surface stays entirely in the tangent plane. If one follows the surface along the respective tangential direction, then one always stays in the same tangent plane. This plane constantly touches the surface. It follows that parabolic surfaces are composed of straight lines and that, along these straight lines, they are touched by the same plane. ⊕ Remark : However, the condition that a surface is composed of straight lines is not sufficient. Quite the contrary: Most curved surfaces that are composed of straight lines are not developable! ⊕

How, then, can we find out whether a surface is parabolic throughout? If each tangent plane touches along a whole straight line, and if this tangent

4.1 Planar and space curves

145

Fig. 4.34 Developable remains developable. . .

plane happens to run through the projection center, then each point of the straight line is a contour point. In other words: The contour of such a surface is composed of nothing but straight line segments (Fig. 4.33, Fig. 4.34, and Fig. 4.35). The only surfaces that can be developed into the plane without distortion are surfaces without elliptic or hyperbolic points. A developable surface can be recognized by the fact that its contour is straight from any viewpoint.

Fig. 4.35 Straight outlines and shadow boundaries in a virtual enveloping cone

⊕ Remark : Insects such as hazel leaf rollers are capable of bending and rolling a leaf in a peculiar way and laying their eggs in the protected “nest” that is thus created. Sometimes, dehydration alone causes a leaf to assume other developable forms (Fig. 4.36). Since the “shrinkage factor” is not the same for all parts, being lower, for example, at the leaf-veins, “shrivelling” soon occurs in the leaves. ⊕

Even if the contour of an object in space is merely a “harmless” curve, tips occur relatively often when dealing with the contours of hyperbolic surfaces: In each case the tangent plane in a contour point contains the center of

146

Curved but simple

Fig. 4.36 Shrivelled leaves and curved contours

the projection. That is why the tangent at the contour often passes exactly through the center. At this point, let us make an additional statement about the osculating circles of a space curve. A picture says more than a thousand words – therefore, simply enjoy the following (more information can be found in academic literature):

Fig. 4.37 All osculating circles of a space curve and their axes form a surface.

If a point moves along a space curve, the related osculating circle constantly changes. The surface that is generated by all these osculating circles can be very complicated (Fig. 4.37 left) and is always doubly curved. However, if we are dealing with a surface containing the axes of all osculating circles, we also have a curved surface, though it is only single curved in that case. This kind of surface is called polar developable or evolute developable.

4.1 Planar and space curves

147

Its analogue in the plane is the locus of all centers of curvature of a planar curve – the evolute. Fig. 4.37 on the right shows the polar developable of a cubic circle (see also Fig. 6.41).

Analogous considerations for shadows

Fig. 4.38 Self-shadow and cast-shadow of curved surfaces

As we already know, there is actually no difference between projection and illumination. All that we have learned so far about projection equally applies to central and parallel illumination. Instead of the contour, we now refer to the boundary of the self-shadow (terminator), and instead of the outline of the projection, we now refer to the cast-shadow boundary. The cast-shadow of a surface is surrounded by the cast-shadow of the self-shadow boundary and possibly by cast-shadows of the surface’s boundary curves. If a surface is developable, a part of the selfshadow / cast-shadow boundary is straight (Fig. 4.38). The line that separates lit areas and areas in self-shadow is called self-shadow boundary or sometimes (especially in the context of planets) terminator. Fig. 4.39 shows that the inner part of a hollow (and therefore non-convex) cylinder carries both types of shadow, which are separated by a straight line through T . The viewer cannot distinguish between the two types, and the separating terminator is not clearly visible. However, someone who draws such figures or writes computer programs to render them needs to be familiar with this. Just to make it clearer, let us repeat the above argument in other words: An object always produces a cast-shadow on planes, on other objects, and potentially – if the object is not convex – on itself. However, there are parts of the surface of the object that are “simply dark” (Fig. 4.40) because they are turned away from the light source. These parts are called self-shadow.

148

Curved but simple

Fig. 4.39 Self-shadow and cast shadow of curved surfaces: On the inner part of the cylinder, we have a cast shadow of the cylinder on itself and self-shadow (“dark areas”).

Fig. 4.40 “Dark” parts on a surface: The parts of the surface that are turned away from the light source are in “self-shadow.” If the surface is not convex (as in this example), additional cast-shadows of the surface will potentially appear on itself (not displayed in these images), especially when the light comes from higher above (images to the right).

Fig. 4.41 The test in practice: At sunrise, some hours later (hazy) and in the afternoon.

149

4.2 The sphere

4.2 The sphere Despite the fact that we have talked about developable surfaces in adequate detail, let us start with a surface that is not developable. The sphere is particularly easy to imagine, occurs frequently, and has many special properties.

Fig. 4.42 Spheres as distance surfaces

The sphere is the locus of all space points that have a constant distance (the radius r) from a given point (the center M ). The sphere can be defined in a different way, which is advantageous for many geometric considerations:

Fig. 4.43 A sphere is generated by the rotation of a circle about its diameter.

A sphere is also formed by the rotation of a circle about an arbitrary diameter of this circle. Let us consider a point P of the circle during a rotation about an arbitrary diameter d (Fig. 4.43): It describes the path circle with the axis d and the

150

Curved but simple

radius dP . At maximum radius, the straight line M P is orthogonal to the axis d. Sphere circles with a maximal radius (the sphere radius) are called great circles – all other circles are small circles. If P lies on d, then the small circle shrinks to a “null circle”. Its carrier plane is orthogonal to the sphere’s radius at the contact point (Fig. 4.44). If we now consider that d can be chosen in an infinite number of ways, we have proven the important theorem that every planar section of a sphere is a circle (Fig. 4.46): Each planar section of a sphere is a circle. The intersection circle is a great circle only if the plane contains the center. All tangent planes of the sphere are orthogonal to the radius at the contact point.

Fig. 4.44 Tangential planes of a sphere orthogonal to the radius at the contact point

Fig. 4.45 The intersection of two spheres is always a circle.

If we let two circles rotate about a common diameter, we get two spheres (Fig. 4.45). During rotation, the common points of the circles generate the same circle:

151

4.2 The sphere

Fig. 4.46

Circles as intersections of spheres

The intersection of two spheres is always a circle which lies in a plane orthogonal to the straight line spanned by their centers. ⊕ Remark : An additional remark for advanced readers, who may think that the theorem should be stated more precisely: Two spheres only share a circle if they are close enough to each other. In fact, it can be calculated that two spheres always share a circle, but it is not always a real one. Its center is always real and lies on the straight line joining the spheres’ centers. We can further say (in what may be an overstatement): Two spheres always share a non-real circle in the plane at infinity – the so-called absolute circle (see also p. 194). Once we know this, some things are no longer surprising: Two spheres should share a space curve of degree four, but because the absolute circle is always part of it, the intersection splits off, and there only remains a planar curve of degree two – a circle which may be real or complex, or even a single point. ⊕ ⊕ Remark : If we rotate a circle not about one of its diameters but about a chord, we get a so-called spindle torus (Fig. 4.47 center and right). We will discuss it further in the section concerning surfaces of revolution. ⊕

Parts of spheres often occur in architecture and technology. They may be found, among others, in hanging domes, spherical caps, and Byzantine domes.

152

Curved but simple

Fig. 4.47 Left: a circle rotates about one of its chords, generating a spindle torus. Right: The roof of the famous Cathedral of Santa Maria del Fiore in Florence (Filippo Brunelleschi, see also Fig. 9.2) is an approximation of a spindle torus. Neighboring circular arcs are combined with (elliptic) cylinders.

▸▸▸ The position of an airplane The distance r of an airplane to a ground control station B can be determined via radar. The airplane lies on the distance sphere around B at the distance r (Fig. 4.48). If the synchronous measurements of three ground control stations (with specified relative positions) are known, one gets three distance spheres that share two points: Two spheres intersect along a circle, and all three circles pass through the common points (Fig. 4.49). One of these (above the surface of the earth) is the position of the airplane. ◂◂◂ ▸▸▸ The “spatial Pythagoras” We are looking for a cuboid where the three edges connected to the corner P pass through three fixed points A, B, and C (Fig. 4.49, center). Due to ∢AP B = ∢BP C = ∢CP A = 90○ , the point lies on the Thales spheres above AB, BC, and CA. For this cuboid corner, it can be shown very elegantly by using vector calculus that the square of the area of the triangle ABC is equal to the sum of the squares of the triangle areas AP B, BP C, and CP A. The analytic proof can also be found in [9] and is given here as well due to its brevity: Proof : Let P be the point of origin of a Cartesian coordinate system with the points A(u, 0, 0), B(0, v, 0), and C(0, 0, w). The triangles AP B, BP C, and CP A then have the areas u⋅v , v⋅w , and w⋅u . 2 2 2 The surface d of the triangle ABC results from the cross product

d=

RR −u RR vw RR −u RR 1 Ð→ Ð→ 1 RRRR⎛ ⎞ ⎛ ⎞RRRR 1 RRRR⎛ ⎞RRRR 1 √ ⋅ ∣AB × AC∣ = ⋅ RRR⎜ v ⎟ × ⎜ 0 ⎟RRR = ⋅ RRR⎜wu⎟RRR = ⋅ (vw)2 + (wu)2 + (uv)2 . 2 2 RR⎝ 0 ⎠ ⎝ w ⎠RR 2 RR⎝ uv ⎠RR 2 RR RR RR RR

153

4.2 The sphere

P

C

A B

Fig. 4.48 Intersection of three hemispheres: Two hemispheres always intersect each other along a semicircle. All three hemispheres have a common point.

Fig. 4.49 Intersection of three spheres and cuboids through three points (center)

Thus, d2 =

1 [ (vw)2 + (wu)2 + (uv)2 ] = b2 + c2 + a2 . 4

⊙

◂◂◂

▸▸▸ Newton’s kissing number problem How many spheres of the same size can be arranged around a central sphere of that same size so that they each touch the central sphere? Newton’s correct assumption was twelve spheres, because a thirteenth sphere simply would not fit even though there was a little space left. How can we provide a solution to this problem? Solution: Let r be the sphere radius. Then, all the spheres that touch the central sphere Σ0 (center in the coordinate origin) lie on a sphere Σ∗0 with radius 2r that is concentric to Σ0 . We select the first sphere on the x-axis, say Σ1 . Now, all spheres that touch Σ1 lie on a sphere Σ∗1 with radius 2r that is concentric to Σ1 . The intersection circle of Σ∗0 and Σ∗1 is a horizontal circle in the xy-plane √ (with radius 3r). Now – as in the two-dimensional plane – one could find six spheres in the xy-plane and then proceed from there. However, this does not

154

Curved but simple

Fig. 4.50 Left: Six circles fit precisely around a central (blue) circle of the same size. Center: A sphere (represented here in blue) is given. The aim is to pack as many spheres of the same size as possible around that blue sphere. Right: This cellar spider is faced with the same problem when carrying its eggs around in a sac.

make for ideal packing, even though we could “stick” three (orange) spheres on both sides and thus get exactly twelve spheres. It turns out that there is still a bit of room for improvement. Let us, then, select only one neighboring sphere Σ2 in the xy-plane and follow the same steps (concentric circle Σ∗2 ). In the intersection of Σ∗0 , Σ∗1 , and Σ∗2 , we will get two further sphere centers that are symmetrical with regard to the base plane, etc. Again, we have twelve spheres around Σ0 . There is some space left, but not enough to add a thirteenth sphere. It was only in 1953(!) that this could be proven (see http://de.wikipedia.org/wiki/Kissing_ number_problem). In nature, we might be able to add a thirteenth sphere by ◂◂◂ squeezing and pushing (Fig. 4.50 right).

Outline and shadow of a sphere The following theorem provides the key for all further considerations: The tangent planes of a sphere along a small circle envelop a cone of revolution, and those along a great circle envelop a cylinder of revolution. Proof : Let us imagine a circle k (center M ) in the plane (Fig. 4.51) and a point S, from which two tangents t and t∗ to k exist. The straight line T T ∗ connecting the contact points is – for reasons of symmetry – perpendicular to the diameter d = M S. Let the carrier plane of the circle now rotate about d. The circle k becomes a sphere Σ, t generates a cone ∆ of revolution with the apex S, and the contact point T generates a small circle u with the axis d. The tangent of u at T and the line ST span the tangent plane τ of ∆. During rotation τ envelopes ∆. If we now let S pass into infinity (S∞ ), then the cone of revolution becomes a cylinder of revolution, and the small circle u becomes a great circle. ⊙

How do we see a sphere from the center S? From S, we can consider an enveloping cone of revolution that touches the sphere. If S is a point at infinity, then the cone becomes a cylinder of revolution. The contact curve of the

155

4.2 The sphere

Fig. 4.51 Tangential cone and cylinder

Fig. 4.52 Outline and shadow of a sphere

cone or cylinder of revolution is a small circle or great-circle u respectively. However, this circle is already the contour of the sphere: According to construction, the tangent plane in each point passes through S. The analogue is true for central and parallel illumination. Let us summarize: The contour and self-shadow boundary (terminator) of a sphere is always a circle on the sphere. With parallel projection or parallel illumination, the contour and self-shadow boundary is a great circle. ▸▸▸ The tilt of the slender moon crescent – a “result of temperature”? Why does the slender moon crescent often appear to be “lying on its back” in tropical regions while having a more upright position in northern regions? Solution: Whether or not the moon crescent is inclined or upright depends on the moon’s terminator (see also application p. 79). It appears as an ellipse, and its apparent inclination (tilt) depends on its principal axis. Therefore, it matters from which direction the Moon is illuminated. If it is illuminated

156

Curved but simple

Fig. 4.53 Tilt of the slender crescent: a) at the poles, b) at the equator, beginning of spring or fall, c) somewhere in-between in winter, d) somewhere in-between in summer

from the side, then the slender crescent appears to stand upright, and if the light comes from above or below, then an inclination becomes apparent. We must further be aware of the following: From the vantage point of Earth, the path of the new moon follows the path of the Sun, though with a certain delay (see also p. 488). This is also approximately true for the slender moon crescent (but not for fuller moon phases). Let us start with an extreme: At the North Pole (Fig. 4.53 a), the path of the sun (if it is visible at all) appears as a circle at a fixed elevation. The slender moon crescent should also appear at a similar elevation – and not very far from the sun. When viewed from the pole, the Moon is illuminated “from the side” so that the self-shadow boundary (terminator) is visible as an upright half-ellipse. In the deeper polar winter, neither the Sun nor the moon crescent can be seen. (However, as is apparent on p. 488, the full moon in polar winter is very much visible. Upon closer inspection, it can be discovered that the near-full moon looks the same as in the tropics!)

Fig. 4.54 Within several hours, our Moon, when photographed from one and the same location on Earth, changes its inclination, provided we keep the lower edge of our camera parallel to the ground. The images above show two cases: the picture on the left was taken two hours before sunset, the picture on the right six hours later.

157

4.2 The sphere

Now for the other extreme: At the equator, there are two days of the year when the sun moves at a circle through the zenith (Fig. 4.53 b). The slender moon crescent follows this path. This time the terminator appears as an inclined half-ellipse: From the perspective of the equator, in the days around new moon, it is illuminated almost precisely from the top (waxing moon, in the afternoon and evening hours) or from the bottom (waning moon, in the morning hours). In general, path circles of the Sun and the Moon in the days around new moon are steeper in latitudes closer to the equator. The steeper they are, the flatter the ellipse appearing as the images of the Moon’s terminator are. It can further be said that the crescent moon will predominantly occur in summer, not in winter, because the sun’s path is steeper in summer (Fig. 4.53 c and d). Therefore, it is not at all far-fetched to say that the position of the slender moon crescent is correlated to (even if not directly caused by) temperature ◂◂◂ ... ▸▸▸ Spheres and spherical parts everywhere . . . Spheres can be found everywhere, especially in nature: Because of gravity, celestial bodies like suns, planets and even moons with a diameter of more than 500 km are shaped in a way that closely resembles a sphere. Surface tension causes water droplets to also take the shape of spheres (Fig. 4.55), since a sphere allows a given volume to be enclosed by the smallest surface possible.

Fig. 4.55 Tiny water droplets in a spider net and on a leaf

In technology, parts of spheres can also be found quite often. In Fig. 4.56 we can see some navigation systems which are commonly used on ships: On the left, hemispheres are attached to a cylinder of revolution. In the transition from one surface to the other, we can see a sharp bend in the selfshadow boundary. In the center image, two sphere caps and a short cylinder of revolution between them can be detected. On the right, the shape of a “satellite dish” approximates a sphere cap very closely (theoretically, it is

158

Curved but simple

a paraboloid of revolution, see application on p. application p. 241). The self-shadow of the cap is circular (see also Fig. 4.81).

Fig. 4.56 Navigation systems on ships

As a last example, let us analyze the shades and shadows in Fig. 4.57. The bowl with small spherical tomatoes inside has the shape of a half sphere. The half sphere is bordered by an equator circle which is composed out of two half circles c1 and c2 . The left half circle c1 casts a circular shadow cs1 onto the spherical interior of the bowl, the right half circle c2 casts a congruent shadow cs1 onto the table plane parallel to the equator plane. The half sphere is separated into two spherical parts by the half great circle (terminator) e = e1 ∪ e2 . e is optically hard to detect, but the shadow it casts is the dominant ellipse es = es1 ∪ es2 on the table.

e1

c1 t

cs1 c2 t

s

es1 cs2

e2 es2 Fig. 4.57 The bowl has the shape of a half sphere.

Finally, let us consider the tiny tomatoes to be spheres. The sun rays touching them along their terminator t form cylinders of revolution. The shadow ts of the terminator onto the bowl is the intersection curve of the cylinder with the sphere – a space curve that is “almost” a circle. ◂◂◂

4.2 The sphere

159

The shortest path on a sphere In space, the shortest connection between two points is a straight line. On the globe, we encounter a problem when dealing with larger distances: We cannot, like Jules Vernes, travel through the center of the Earth. The shortest connection between two points A and B on the sphere is a great circle – a circle whose plane is defined by A, B, and the center M of the sphere. Therefore, if a ship were to travel from a certain circle of latitude to another point on the same latitude, the shortest path would not follow this circle (except at the equator or a meridian)! ⊕ Remark : The circle of latitude would be more practical for navigation purposes: It can be calculated without much trouble by measuring the angle of elevation to the peak level of the sun (see p. 481). For this reason, it used to be common in old times to travel along circles of latitude – better to cross some more sea miles than to “miss” a life-saving island in the ocean: The precise determination of the circle of longitude used to be very difficult at sea. This problem was eventually solved by the use of “stormproof” clocks [9]. ⊕

Fig. 4.58 Left: shortest path from Vienna to Varadero. Right: Flight paths are – at least in theory – great circles. In practice, jet streams especially, but also other factors, must be taken into account. That is why many flights head up high to the North even when their origin and destination airports lie on the same circle of latitude.

▸▸▸ From Vienna to Varadero In the age of GPS (Global Positioning System, Fig. 4.56), attempts may actually be made to come close to the great circle while crossing from A to B. Of course, one must not forget the importance of water and air streams (“jet streams”) when undertaking such an endeavor. Fig. 4.58 shows a flight path between two continents – naturally displayed on a 2D map, on which

160

Curved but simple

great circles are not recognizable as such. These are photographs of a lowresolution monitor within an airplane.

Fig. 4.59 The global distribution of GPS-satellites (flight altitude of approx. 20 000 km)

In the middle of Fig. 4.58, the 2D map was transferred onto a sphere. The flight path should now come close to a great circle (the offset is negligible). The flight from Vienna (48○ northern latitude, 16○ eastern longitude) to Varadero in Cuba (20○ northern latitude, 70○ western longitude) leads into northern latitudes at first. From the globe shadow, which deeply envelops the North Pole, it can be concluded that the flight must have taken place at the approximate time of the winter solstice. During the multi-hour flight, the shadow boundaries move westwards. The image on the right shows the ideal flight path (which is a great circle). Fig. 4.74 shows the distribution of GPS-satellites worldwide. With their flight altitude of more than three times the Earth radius, they orbit the Earth twice a day. ◂◂◂

4.3 Cylinder surfaces

161

4.3 Cylinder surfaces The tried-and-true cylinder of revolution. . . So far, we have already used the term cylinder of revolution because we have assumed that everybody can imagine such an object. Let us now attempt an exact definition: A cylinder of revolution is the locus of all points in space that are equidistant to a given straight line (the axis) at the fixed distance r (the radius). As with a sphere, a cylinder of revolution can also be generated by a motion in space: A cylinder of revolution is generated by the rotation of a straight line about a parallel axis. We can conclude that cylinders of revolution are “refined” regular prisms. Incidentally, computers also display them as regular prisms with a high number of edges. (The eye can barely distinguish the difference between a 200-sided prism and a perfect cylinder.) Both given definitions define a cylinder of revolution as unbounded, or “infinitely long.” In practice, cylinders of revolution are usually delimited by sections which are perpendicular to the axis (circles). The development of such a bounded cylinder of revolution is a rectangle with the width 2π ⋅ r and the height h.

Fig. 4.60 Outline and cast-shadow of a cylinder of revolution

Cylinders of revolution carry only parabolic points (single-curved). Their outline and their shadow are usually composed of two straight lines, including the images or shadows of the boundary circles (Fig. 4.60).

162

Curved but simple

. . . and general cylinders A cylinder is not necessarily a cylinder of revolution (as is the case in technical drawings). A general cylinder is created by moving a straight line parallel along an arbitrary directrix.

Fig. 4.61 General cylinder: planar intersection, intersection with a straight line

General cylinders retain important properties of cylinders of revolution, except for rotational symmetry. They are single-curved (and thus developable), which can also be recognized from the fact that their contours or self-shadow boundaries are composed of straight lines.

Fig. 4.62 Cylindrical boundaries of a sound box

The outline of a guitar’s cylindrical boundaries is a good example. The contours are composed of straight lines, and this is true for the normal projection (the left photo in Fig. 4.62 was taken with a telephoto lens), as well as the central projection (wide-angle lens used in Fig. 4.62 on the right). The photographs at hand were shot with light flare (indoor shot) to avoid sharp shadow boundaries. The shadow of the side wall is, nevertheless, recognizable as being straight.

163

4.3 Cylinder surfaces

Fig. 4.63 General cylinders

Fig. 4.64 Doubly rolled palm leaves

A model of a general cylinder can quickly be “crafted” by everyone: One only needs to drag a piece of paper across the sharp edge of the surface of a table. This procedure changes the structure of the squashed paper, and a paper roll emerges. A phenomenon of this kind often occurs in nature, such as in plant leaves (Fig. 4.64). General cylinder surfaces also play an important role in architecture: They can be used to shape rooftops or façades that are reasonably cheap to produce – owing to the simple fact that they can be cut in the plane. Geometrically speaking, we often deal with parallel projections or parallel shadows with “circumscribed” cylinders – as in the case of the sphere, where the circumscribed cylinder is a cylinder of revolution. Fig. 4.65 shows the cylinders “underneath” different spatial spirals (see Chapter 7, p. 315).

Fig. 4.65 Different spirals on a cone of revolution. Their projection cylinders with generators parallel to the cone’s axis are of interest.

164

Curved but simple

4.4 The ellipse as a planar intersection of a cylinder of revolution A classic proof of spatial geometry

Fig. 4.66 Oblique sections of cylinders of revolution

The ellipse – as defined by the Greeks – occurs as a planar skew section of a cylinder of revolution. Proof : The proof by the Frenchman Dandelin is as ingenious as it is simple: A conventional ellipse is the locus of all points in the plane where the sum of the distances from two fixed points – the focal points F1 and F2 – is constant. Dandelin noted that these points can be seen as the contact points of two congruent spheres that touch both the cylinder of revolution and the plane.

Fig. 4.67 Dandelin spheres

Fig. 4.68 Pipe elbow

4.4 The ellipse as a planar intersection of a cylinder of revolution

165

Let us call the points F1 and F2 (they do not lie on the cylinder of revolution). If we now take an arbitrary point P on the intersection curve, we notice that there exists a cylinder generator e through the point P , which touches the spheres in the points 1 and 2. We can say: The (identical) straight lines P 1 and P 2 touch both spheres, and the sum P 1 + P 2 is constant – equal to the distance from 1 to 2. On the other hand, the straight lines P F1 and P F2 are likewise tangents of the spheres from P . All tangents of a sphere through a fixed point P have a constant tangent distance and form a cone of revolution. Thus, P F1 = P 1 and P F2 = P 2. The sum P F1 + P F2 is also constant (= 12), which is precisely what we wanted to show. ⊙

A multitude of applications If the cylinder is upright, the lowest point A and the highest point B on the intersection curve are the principal vertices of the ellipse (Fig. 4.68). The midpoint M is the intersection of the plane with the cylinder axis. The points C and D (which have the same height as M ) are the auxiliary apices.

Fig. 4.69 Construction of a pipe elbow: Two concentric congruent ellipses are overlapped by means of a rotation.

Both parts of an obliquely truncated cylinder can be attached to form a pipe elbow by rotating one of them by 180○ about the normal of the plane at the center of the ellipse (Fig. 4.69). If the intersection plane forms an angle ϕ with the cylinder axis, then the pipe axes and the plane of the ending circles form the angle 2ϕ. For ϕ = 45○ , the pipe elbow is perpendicular.

Fig. 4.70 Vaults with ellipses as intersections

166

Curved but simple

Four cylinders of revolution that are cut at both sides at 45○ in the manner of a wedge can be put together to create a beam connection. The intersection consists of a pair of ellipses that intersect each other perpendicularly in the neighboring apex (such a connection is visible in Fig. A.10). Geometrically speaking, the same problem arises when two cylinder-of-revolution-like vaults intersect (Fig. 4.70 shows the bottom view of a groin vault and a barrel vault).

Fig. 4.71 Variations of a three-cylinder connection

The variations of such cylinder connections (Fig. 4.71) should illustrate the enormous importance ascribed to planar intersections of cylinders of revolution.

Fig. 4.72 Intersection of two cylinders of revolution: Palmenhaus/Schönbrunn, Vienna

Proceeding with this game, one can connect six pointed cylinder-of-revolution wedges, producing a spatial cross. Six ellipses are involved, and it truly challenges our spatial imagination to sketch such an object. (You can find more on this topic in the appendix concerning freehand drawing.) Fig. 4.73 on the left shows a beam connection with three pairwise orthogonal axes. The “interior” (center left), as a physical model, rolls well. For the computer, such intersections often lead to numerical problems (“near-identical” planes must be intersected). This is why, in Fig. 4.73, the cylinder radii were set to be slightly different, which immediately causes the intersection curves to “break off” at double points.

4.4 The ellipse as a planar intersection of a cylinder of revolution

167

Fig. 4.73 Beam connection with three beams, a variation using eight-sided prisms

In Fig. 4.73 on the right, the cylinders were approximated by regular, eightsided prisms. The shared interior of the prisms is, then, a solid that is composed of congruent squares or hexagons.

Fig. 4.74 Illustrations like these can be helpful to spatial imagination.

Multiple cylindrical ungulas can be attached “in sequence” (Fig. 4.76), thus creating an approximation to a so-called torus, about which we will have much more to say at a later stage. During development, a cylinder of revolution bounded by circular sections changes into a rectangle with width 2π ⋅ r. What kind of curve results from an elliptical oblique section? This time, a calculation is obligatory. We have to relate the arc length that occurs during development to the height of a curve point. Let us consider an ellipse point in plan view and front view. In the plan view, P ′ is a circle point with the coordinates x = r ⋅ cos u, y = r ⋅ sin u (u is the polar angle in radians). If the section plane is inclined towards the horizontal base plane (a plane at the height of the neighboring apex) at an angle of α = 90 − β, then the height of P equals z = y ⋅ tan α = k ⋅ y (k being constant). When developed, the point has the coordinates P v (r ⋅ u/z) or P v (r ⋅ u/k ⋅ r ⋅ sin u). The developed curve is, therefore, essentially a sine curve. The principal vertices 4 and 8 of the ellipse (Fig. 4.75) correspond to the apices of the sine curve. The auxiliary vertices correspond to the inflection points of the sine curve. The inclination of the tangents at the inflection

168

Curved but simple

Fig. 4.75 Development of a cylindrical ungula: The development of the intersection curve follows a sine function, of which the osculating circles and the tangents of inflection (angle β) should be specified. (For example, the osculating circle at point 4 is equal in size to the osculating circle of the ellipse that is orthogonally projected onto the tangent plane τ .)

Fig. 4.76 Development of a pipe connection

points equals the inclination of the plane which can be seen in the front view. ⊕ Remark : When a pipe connection is developed, it is equally valid to develop a prototype. The other parts are congruent. It is possible to proceed even more economically: By imagining the ungula as rotated by 180○ before development, the pipe connection is stretched into a single cylinder of revolution (Fig. 4.76). Therefore, we only need to develop one cylinder of revolution with potentially multiple (though essentially congruent) oblique sections. The result is a rectangular strip to which one or more (often congruent) sine curves are inscribed. This minimizes wear, which will delight the pragmatist! ⊕

Of course, it doesn’t work every time

It appears contradictory that the intersection of two cylinders of revolution should yield two ellipses, since the following famous theorem holds: Bézout’s theorem: Two algebraic surfaces of degree m and n generally share an intersection curve of degree m ⋅ n.

4.4 The ellipse as a planar intersection of a cylinder of revolution

169

Fig. 4.77 Arbitrary intersections of cylinders of revolution

Proof : The two surfaces are intersected by an arbitrary test plane along two planar curves of the orders m and n. It is sufficient to show that these m have n points in common, because the intersection curve must be of the same order. The theorem about planar algebraic curves is, as the name indicates, a classical algebraic problem and remains to be proven. The algebraic curve of n-th order is given by the implicit equation i j ∑ aij ⋅ x ⋅ y = 0 with 0 ≤ i + j ≤ n.

The algebraic curve of degree m can be written in the same way: i j ∑ bij ⋅ x ⋅ y = 0 with 0 ≤ i + j ≤ m.

We eliminate one variable, say y, from both equations by computing the resultant of the two polynomials. This yields an algebraic equation of degree m ⋅ n. According to the fundamental theorem of algebra, this polynomial possesses m ⋅ n solutions (including complex and multiple solutions). ⊙

Fig. 4.78 Filleting of an intersection

Fig. 4.79 Arbitrary intersection of cylinders (on the left: beaver food)

If one intersects two quadratic surfaces (to which cylinders of revolution belong), then a space curve of degree four is to be expected.

170

Curved but simple

Fig. 4.77 shows the intersection curves of cylinders of revolution with intersecting axes and slightly different radii. (The curves appear as circles when projected in the direction of the axes, and as parts of hyperbolas when projected orthogonally to the plane spanned by the axes.) Such intersections occur very frequently in technical applications. Fig. 4.79 shows a curious example from nature: A beaver has gnawed away at a mighty tree, which may be blown over by the next storm.

Fig. 4.80 The space curves may split into parts under certain circumstances.

The intersection curve of two cylinders of revolution may also split into parts: When put together, both section ellipses also form a space curve of degree four. (After all, they share four points with an arbitrary plane.) Fig. 4.80 illustrates how the intersection of two cylinders of revolution may disintegrate if two criteria are given: First, the cylinders must have an equal radius, and second, their axes must intersect. In other words: Both surfaces must share an inscribed auxiliary sphere. In the normal projection to the plane that is spanned by the axes, the hyperbola that occurs for different radii splits into a pair of straight lines: A hyperbola does not possess a double point. Degenerating intersections are not only frequently employed in technology, but they can also be observed in nature (in the context of shadows), which is due to a second theorem: The shadow of a planar boundary curve of a degree-two (quadratic) surface onto itself is a conic section. Proof : The planar boundary curve is a conic section c and, in the case of a sphere or a cylinder of revolution, a circle (Fig. 4.81). The light rays through c form a degree-two cone Λ (an oblique cylinder in the case of parallel shadows). In both points T1 and T2 , where the self-shadow boundary of the surface (a conic section

4.4 The ellipse as a planar intersection of a cylinder of revolution

171

Fig. 4.81 Shadow of a sphere part or a cylinder of revolution on itself

or a pair of straight lines) intersects the boundary curve, the light cone and the surface touch each other. Due to this double tangency, the intersection curve splits into two conic sections, one of which is the boundary curve c. The other curve c∗ carries the boundary of the boundary curve’s shadow onto the surface itself. ⊙

Fig. 4.82 Self-shadow of a planar intersection on a sphere or a cylinder of revolution

▸▸▸ Shadows as intersection curves Fig. 4.83 (left image) shows a lamp that appears to produce sunlight. The other two photos show what happens with the light in the next 90 minutes after the first photo was taken. The artist has covered a window with a sheet of paper that has an elliptic hole cut into it, and through this hole sunrays can enter the room. The shadow of the ellipse will normally be an ellipse, but under specific circumstances it can also be a circle. In this special case, the cylinder that is defined by the circle and the direction of the sunrays is an oblique circular cylinder, and the corresponding ellipse on the paper is a vertical section of it. In this way one will find a fitting ellipse for arbitrary directions of the incoming light. Fig. 4.84 shows that the light rays surrounding the tire form an approximately oblique circular cylinder. (In the photograph, it is depicted as a cone with the sun point for its apex.) An intersection with the half pipe (which is itself

172

Curved but simple

Sunlight, Earth rotation, paper, lamp: sunlight through an elliptic opening in the window and its movement during 90 minutes (Liddy Scheffknecht: oculus, 2012). Fig. 4.83

Fig. 4.84 The shadow of a tire on a curved road is a space curve of degree four.

part of a cylinder of revolution) results in a space curve of degree four as the shadow of the tire.

Fig. 4.85

Shadows of a radiator on a curtain

4.4 The ellipse as a planar intersection of a cylinder of revolution

Fig. 4.86

173

The radiator behind the curtain

Fig. 4.85 shows the shadows of the radiator of a central heating onto a curtain. The radiator itself is depicted in Fig. 4.86. ◂◂◂

The process of development. . . Fig. 4.87 on the left illustrates how a sheet of brass shaped like a cylinder of revolution can be distorted into a rectangle. Mechanically, this is accomplished by continuously bending the brass by small amount at even time intervals. The further away from the cutting position a generator lies, the more often the bending procedure has to be repeated.

Fig. 4.87 Development of a cylinder of revolution and how it is used to roof a swimming pool

The position highlighted in red looks approximately like half of an elliptic cylinder (though this resemblance is not exact). In Fig. 4.87, right, this position was used as the roof of a small swimming pool. The reflection in the water gives the additional appearance of a closed (and almost elliptic) cylinder.

. . . and its inversion (rolling up the development) In practice, instead of developing a surface, it must sometimes “envelop” it (Fig. 4.88). Simple examples include the placement of a label onto a bottle

174

Curved but simple

Fig. 4.88 Inversion of the development (“envelopment”) on a cylinder of revolution. On the left: rewinding straight lines (helices) and a circle. On the right: A circular aluminum foil rolled into a cylinder of revolution is used as a “spout.”

and the circular aluminum foil that is rolled up and put into a bottleneck to prevent its liquid content from dripping when it is poured (Fig. 4.88 on the right). The “inclusion” of straight lines during envelopment produces geodesic lines on the carrier cylinder (see p. 142). In the general case, these are helices – we shall later address these important curves in great detail. If a circle whose diameter equals the circumference of the cylinder is also rewinded, a curve with a tacnode, i.e., a point where the curve touches itself, is produced. Such a curve is highlighted in red in Fig. 4.88 on the left. The tacnode is visible in the obscured region. In the background of Fig. 6.34, circles rolled up onto a cylinder of revolution are visible on the bamboo stools.

Fig. 4.89 rolling up

Fig. 4.90 “Rolling up” of a circle

In purely geometric terms, the production of potato chips in Fig. 4.90 is a tricky matter. Obviously, a thin layer of pulp is cut out. If it is then rolled up onto a cylinder of revolution – as with a “rolling pin” – we would not yet expect a doubly curved surface. It can be assumed that the pulp is immediately pressed onto a doubly curved stencil. The pulp is thick enough to stand the necessary stretching. Fig. 4.89 on the left shows two ancient Egyptian bracelets where planar curves made of pure gold were enveloped onto an “elliptical cylinder” (the forearm).

5

More about conic sections and developable surfaces

Like spheres and cylinders, cones are surfaces that we can easily imagine. Like cylinders, they are simply curved and developable. Among all cone surfaces, the cone of revolution and the oblique circular cone are especially important. Their planar sections are the conic sections per se: ellipses (among them circles), hyperbolas, and parabolas. We can derive many common properties through a spatial interpretation of these most famous planar curves. Cones and the cylinders are developable: they can be unrolled into the plane without distortion. They only share this characteristic with so-called developables, sometimes also called torses or tangential surfaces of space curves. Like cylinders and cones, these are composed of straight lines called generators or rulings. Developables are envelopes of one-parameter families of planes where each plane touches along a certain generator. This makes them easily recognizable: From any viewpoint, their contours are generators. The shadow boundaries, too, always have straight components. Doubly curved surfaces, such as the sphere, cannot be unfolded into planes without distortion, but because this is such an important task, mathematicians and geometers have spent an immeasurable amount of time on the issue of transforming the surface of the globe into a planar map while leaving certain geometric properties unaffected by the process.

© Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_5

175

176

More about conic sections and developable surfaces

5.1 Cone surfaces Like cylinders, cones are notable for their simplicity. We can explain cones as follows (Fig. 5.1):

Fig. 5.1 The motion of a straight line through a fixed point (the apex); right: an approximation

A cone is generated by a straight line e that always passes through a fixed point S. S is the apex, e is a generator and each pose of e can also be considered a generator of the cone. In geometry, a cone is not bounded and can thus always be interpreted as a double cone, i.e., the surface consists of both parts on either side of the apex (Fig. 5.2 on the left). Among cone surfaces, the cones of revolution are the most important:

Fig. 5.2 Shadows of cones and cylinders of revolution

A cone of revolution is generated by the rotation of a straight line e about an intersecting axis.

5.1 Cone surfaces

177

Fig. 5.3 Cone of revolution with circles of latitude and generatrices

Only parts of cones of revolution occur in practice, and these are sometimes not even easily identifiable as such (see Fig. 5.4 and Fig. 5.5).

Fig. 5.4 Rotation of straight lines and a cone-shaped excavation

Fig. 5.5 Vulcania European Park of Vulcanism Conus by H. Hollein (parts of cones of revolution)

The development of a cone of revolution All generatrices of a cone of revolution have the same length. Or more precisely: All sections of the generatrix between the apex and a circular section are equally long. Therefore, if we develop a cone into the plane, it becomes a circular sector. According to Fig. 5.6, the central angle ω of the circular sector can be derived by equating the respective circular arcs. With the notations from the figure,

178

More about conic sections and developable surfaces

Fig. 5.6 Development of a cone

we have 2π ⋅ r = ω ⋅ s and thus r ω = 2π s

and also in degrees ω ○ =

r ⋅ 360○ . s

Given an equilateral cone with s = 2r, we get half a disc. A frustum of a cone of revolution is developed into an annular sector. Curves on the cone become curves that intersect the generatrices at the same angle as they did in space (application p. 198). ▸▸▸ Rolling up onto a cone As with cylinders of revolution, we can also “invert” the development. We can inscribe an arbitrary curve k v into the developed lateral area of the cone of revolution, such as a circle (as in Fig. 5.7).

Fig. 5.7 Rolling up a circle

The result is a space curve k on the cone that, if developed, produces the curve k v . The curve k can be determined as follows, point by point: We pick

5.1 Cone surfaces

179

a generator ev in the development. We then determine the central angle ϕ to the respective central angle ϕv on the base circle and thus reconstruct the generator e on the cone. Finally, we measure the distance S v P v from the development on e. ◂◂◂ ▸▸▸ An unbalanced dumbbell rolling on a plane If the co-axial wheels of trains were not conical, they would continually derail. Even the steel ring on the inside of the wheel (Fig. 5.8) could not prevent derailment.

Fig. 5.8 The components of the wheels of a train and the rails . . .

The slightly conical shape of the wheels (Fig. 5.8) is essentially responsible for that effect: If the train drifts to the right, then the contact circle on the right wheel apparently increases its diameter due to the conical shape of the wheel. At the same time, the diameter of the contact circle on the left wheel decreases (causing a tilt of the axis). This is what forces the axis to move back into the correct and stable position. The smaller and the larger circle can be interpreted as parallel circles of a virtual cone of revolution. In the perfect equilibrium of a train that runs smoothly along the rails, the circles have the same size and the connection surface is a cylinder of revolution.

Fig. 5.9 Left: A virtual cone – the hull surface of an “unbalanced dumbbell” – is rolling on a plane. Right: The circles of contact of each wheel (red) also form such a virtual cone. The rigid wheel system will steer around a left curve when the left circle is smaller.

When the train has to navigate a curve, the conic wheels are also of great advantage. Imagine the left curve in Fig. 5.9: The tracks have to be inclined,

180

More about conic sections and developable surfaces

otherwise the centrifugal forces would tip the train over. However, these centrifugal forces will still shift the train to the right. This causes the circle of contact with the right track to increase, and the corresponding circle on the left to decrease. This achieves the desirable outcome of the train automatically tilting to the left (Fig. 5.9). Inclining not enough to the right will push the train further right, whilst inclining too far to the right will push it back to the left. The perfect equilibrium lies somewhere in between. ◂◂◂ ▸▸▸ A plane rolling on a cone Instead of a cone rolling on a plane we can let a plane roll on a cone. In this case, the point in the plane that touches the apex will not move. Points in the plane that are at a constant distance from the apex (and therefore lie on a circle) will move on spheres. This movement belongs to the topic of spherical kinematics, which we will discuss in greater detail in Chapter 11.

Fig. 5.10 A circle rolls on a cone with an apex identical to its center. Straight lines in the plane leave “traces” on the cone. When the cone is developed, those traces are rectified to straight lines again.

Straight lines in the planes leave a “print curve”, which is also called a geodesic curve, on the cone. ◂◂◂ General cones are, in practice, not as common as arbitrary cylinders. They are sometimes found in the form of connecting surfaces of two “directrices,” which often reside in parallel planes (Fig. 5.15). ▸▸▸ Connecting cone between a rectangle and a circle Fig. 5.11 shows how a connecting surface composed of (planar) triangles and oblique circular cones can be pieced together in such a way that there are no edges: If, for instance, a circle k and a rectangle r in parallel planes are given as boundary curves (Fig. 5.11 on the left), then the points 1, 2, 3, and 4 on k –

181

5.1 Cone surfaces

Fig. 5.11 Connecting surface between a rectangle and a circle in theory. . .

Fig. 5.12 . . . and practice

where the tangents are parallel to the rectangle sides – are to be determined. These points are then connected to the rectangle sides by triangles. Four oblique circular cones, which are touched by the triangles, remain. If the carrier planes of the boundary curves are not parallel, then the points 1, . . . , 4 can be obtained by intersecting the rectangle sides with the section line s and, from there, positioning the appropriate tangents to k. ◂◂◂ ▸▸▸ The jet of a hairdryer We want to connect a “rounded rectangle” with a circle in a parallel plane by a smooth surface.

Fig. 5.13 Theory . . .

Fig. 5.14 . . . and practice

182

More about conic sections and developable surfaces

Solution: Fig. 5.13 shows a case where the rectangle is rounded off by circles. Fig. 5.14 shows a practical application of this case. The following idea leads to an elegant solution: The longer sides of the rectangle can be “handled” – as in the previous example – by the use of two triangles. Two circles of different sizes in parallel planes remain (if we imagine the upper half-circles as complete). There now exist two oblique circular cones with the apices S1 and S2 on which the circles lie. They form the connecting surfaces that touch both triangles. Fig. 5.15 shows an airport counter designed according to this method. The advantage, apart from an aesthetic one, lies in the fact that there are no hard ◂◂◂ edges that could cause injuries. ▸▸▸ The cone according to Le Corbusier Fig. 5.16 depicts a design by the French architect (1887–1965) who was famous for his formally strict yet functional architecture. A more precise analysis of the sophisticated object shows its remarkably simple method of construction: As in application p. 180 (connecting cone between a rectangle and a circle), Corbusier developed a connecting surface between a base square and a circle. He then simply and obliquely truncated the object composed of triangles and oblique circular cones. The top surface is composed of ellipse fragments (see the next section) and straight lines. ◂◂◂

Fig. 5.15 Connecting cone . . .

Fig. 5.16 . . . of two directrices (after Le Corbusier )

A theorem with great technical applicability Without doubt, geometry can be fascinating by itself, regardless of any practical applicability. It is, nevertheless, pleasing to find applications of geometrical theorems in everyday contexts. Here is a good example: If two surfaces of degree two touch at two points, then the intersection curve splits into two conic sections.

183

5.1 Cone surfaces

Fig. 5.17 Symmetrical and asymmetrical trouser parts

It can be shown that a non-degenerate intersection curve of degree four can only possess one double point (a self-intersection). On the other hand, it can also be proven that whenever two surfaces touch each other, the intersection curve must possess a double point precisely at the contact point. Now, we can easily understand the following practically relevant theorem based on the aforementioned statement: If two degree-two surfaces share a common inscribed sphere, then the intersection curve splits off into two conic sections.

Fig. 5.18 Cylinder intersection including the explosion sketch

Fig. 5.19 Degenerate intersection of degree-two surfaces

At first, the intersection curve of both surfaces is of degree four. Like the carrier surfaces, it will touch the sphere twice. Both surfaces possess the same tangent plane at the contact points (which are also double points). This leads to the splitting of the curve into two conic sections.

184

More about conic sections and developable surfaces

Fig. 5.19 at the center shows two cones of revolution that have a common inscribed sphere. The intersection curve thus splits off into two ellipses. If only a part of the cone of revolution materializes, then only one ellipse remains.

Fig. 5.20 Exposition in Geneva

Fig. 5.19 on the right goes one step further, performing an affine transformation to the cones of revolution. Thus, they do not remain cones of revolution. In the course of the affine transformation, the common ellipse changes into a new ellipse. This principle fascinated the architectural firm Coop Himmelb(l)au to such a degree that they decided to immortalize it in multiple famous buildings (as in Geneva, where each of the towers is 40 meters tall; see Fig. 5.20 or Fig. 5.21). ⊕ Remark : A spatial affine transformation is very easy to calculate: The new coordinates are simply arbitrary linear combinations of the old coordinates. ⊕

Fig. 5.21 UFA Cinema Center, Dresden and Paradise Cage

185

5.2 Conic sections

5.2 Conic sections Planar sections of a cone of revolution The term “conic section” (often simply called “conic”) is found in every book on geometry, almost as often as “straight line” and “circle.” It is also known as a curve of degree two. This name implies that the curves have, algebraically speaking, two intersections with a generic straight line.

Fig. 5.22 The different conic sections

⊕ Remark : From a mathematical perspective, the curves are given by an algebraic equation of degree two in the form of a1 x2 + a2 y 2 + a3 xy + a4 x + a5 y + a6 = 0

(5.1)

(the first three coefficients must not all be zero – otherwise we are left with a linear equation). If we now insert the linearly dependent term k ⋅ x + d for the variable y, we always get a quadratic equation in x, which leads to the two intersection points. (Multiple solutions and complex conjugate pairs of solutions have to be taken into account.) ⊕

What is a degenerate conic section?

We distinguish between degenerate and non-degenerate (regular) conic sections. From a geometric perspective, regular conic sections are formed by the intersection of a cone of revolution with a plane that does not contain the apex of the cone. Ellipses, hyperbolas, or parabolas thus emerge depending on the inclination of the plane. A plane through the apex of the cone either intersects the cone in two generators, touches it along a generator, or does not intersect it at all (more precisely, it intersects along two complex conjugate straight lines with the apex as the real intersection). ⊕ Remark : Something for the mathematically knowledgeable: A cone of revolution with aperture 2α centered at the origin of the coordinate system and with the z-axis for its axis can be described by the equation x 2 + y 2 − t2 z 2 = 0

186

More about conic sections and developable surfaces

with t = tan α > 0. A non-horizontal intersection with the plane px + z = 0,

p>0

through the origin (normal vector (p, 0, 1)T ) yields the condition √ y = ±x ⋅ p2 t2 − 1, or a pair of straight lines that is real whenever p2 t2 > 1, or p ≤ cot α is given. Otherwise, we are dealing with a pair of complex conjugate straight lines. ⊕

▸▸▸ Various definitions of conics Depending on whether the underlying geometry is Euclidean, affine or projective, conics can be defined by their focal properties, as planar sections of cones of revolution, as perspective images of circles, by their quadratic equation. Even more definitions can be found in [16].

Fig. 5.23 The standard definitions of ellipses, hyperbolas, and parabolas

The standard definition of conics (Fig. 5.23) is based on the focal properties. There is a strict difference between ellipses, hyperbolas, and parabolas. Ellipses are defined as the sets of points P in a plane with a constant sum of distances P F1 + P F2 = 2a = const. Points Q of a hyperbola with focal points F1 and F2 are defined by a constant difference of distances ∣P F1 − P F2 ∣ = 2a = const. The points R of a parabola are characterized ◂◂◂ by equal distances to its focal point F and its directrix l: p = Rl.

Focal points If we also allow points at infinity, then all regular conic sections possess two focal points. In the case of ellipses and hyperbolas, both are regular points, and with parabolas, one of the focal points “slides” in the axis direction towards infinity. This way of thinking has its advantages: Many properties of ellipses and hyperbolas that refer to their focal points can be transferred to the parabola, which, apparently, occupies a notable intermediate position. We do not always need to emphasize the difference between regular and non-regular conic sections either. We can imagine a pair of intersecting straight lines as hyper-

187

5.2 Conic sections

bolas that are simply seen from a very large distance. (A hyperbola is nearly straight at almost all points. It only changes direction very briefly in the vicinity of its vertices.) A parallel or collapsing pair of straight lines could also be imagined as an “infinitely flat ellipse.” Let us, for example, take a theorem that refers to the so-called focal rays (the straight lines connecting a point of a conic section with its focal points): The tangent of a conic section bisects the angle between the focal rays.

Fig. 5.24 The Dandelin spheres

Proof : An elegant proof of this theorem is based on the proof by presented by Dandelin, where a conic section is explained as a planar section of a cone of revolution. The tangent t at a curve point P can be interpreted spatially as the intersecting straight line of the cone’s tangent plane τ with the plane ε. The plane τ touches the first Dandelin sphere at 1 and ε in F1 . For reasons of symmetry, t forms the same angle with the tangent segments P 1 and P F1 . The same is true for the second Dandelin sphere, but since the carrier lines of P 1 and P 2 are identical, t forms the same angle with the focal rays P F1 and P F2 . ⊙

This theorem is of practical applicability. The section concerning degree-two surfaces provides more information on it, addressing concepts such as focal mirrors. Furthermore, the following interesting statement can be derived: Conic sections of different type with two common focal points (confocal conic sections) intersect at right angles. Proof : First of all: The two conic sections are of different types – two confocal ellipses or two confocal hyperbolas do not possess real intersection points. Even confocal parabolas can be disjoint (Fig. 5.28). Thus, it can only be a pairing between either an ellipse and a hyperbola or between parabolas opened in opposite directions.

188

More about conic sections and developable surfaces

Fig. 5.25 The two Dadelin spheres in the case of a hyperbolic section.

For both, it is true that the tangent is the angular bisector of the respective focal rays at the intersection. There are always two angle bisectors forming an orthogonal pair. ⊙

Another theorem that refers to the focal points goes as follows: A conic section is the locus of all points at a constant distance from a fixed circle and a fixed point in its plane. Proof : The “proof” for the parabola actually lies in its definition: The parabola is given as the locus of all points that are equidistant to a point and a straight line. If this director is seen as a circle around the focal point at infinity, everything appears to fit together once again. Concerning the other conic sections, we shall soon prove the generalization of the theorem that includes this special case. ⊙

Once again, there are a number of applications of this theorem. For instance, let us consider the envelope of circles centered at all points of a conic section while passing through a focal point. It is the “director circle” that passes through the focal point. The above-mentioned generalization of the theorem reads as follows: Each conic section is the locus of the centers of all circles that touch two given circles in one plane.

189

5.2 Conic sections

Fig. 5.26 A net of confocal conic sections

Fig. 5.27 Touching circles of two given circles and the locus of their centers

Proof : The parabola occurs only if one of the circles is infinitely large and thus degenerates into a straight line. We have already studied this case. Let k1 and k2 be two circles with the centers F1 , F2 and the radii r1 , r2 . We can now construct the center P of a touching circle k with the radius r if, for example, we intersect two concentric circles around F1 and F2 with the radii r1 ± r and r2 + r (Fig. 5.27). However, for P , we have ∣P F1 ± P F2 ∣ = ∣r1 ± r2 ∣. ⊙ ⊕ Remark : If one of the circles shrinks to a “zero circle,” then the aforementioned theorem applies. ⊕

Parabolas and catenaries It is remarkable that there apparently exists an infinite number of “significantly different” ellipses and hyperbolas but only one prototype of a parabola. All parabolas can be derived from the prototype by a mere enlargement or

190

More about conic sections and developable surfaces

Fig. 5.28 Parabolas and . . .

Fig. 5.29 . . . catenaries with different parameters

shrinking. It shares this property with the circles, the catenaries (Fig. 5.30), and also with “higher-degree parabolas” of the form y = a ⋅ xn .

Fig. 5.30 Catenaries are positions of equilibrium of hanging ropes with not too much additional weight pulling on them.

Parabola (red) versus catenary (green): A heavy flexible rope or chain will take a position of the catenary. Fig. 5.31

The catenary represents the position of equilibrium of a hanging rope; it is further addressed in [9]. We can see from its explicit equation y = a ⋅ cosh

x a x/a = (e + e−x/a ) a 2

that the factor a is only a factor of similarity.

5.2 Conic sections

191

Fig. 5.32 There is an undeniable geometric beauty in suspension bridges (here: Verrazzano-Narrows Bridge). Due to the weight that the bridge’s ropes have to carry, the shape of the ropes comes closer to parabolas than to catenaries.

In the regions of the apex, catenaries resemble parabolas to such an extent (Fig. 5.31) that it is possible to replace catenaries by parabolas in practice (though only approximately). However, if we truncate the power series of the exponential function (which is transcendental rather than algebraic) after the term of degree two, we obtain the equation of a parabola. Catenaries emerge as the solutions of a differential equation: The shape of the curve emerges from the local condition that the tangential pulling forces of the left and right part of the rope should be in equilibrium with the mass at every point.

Fig. 5.33 Upside down catenaries are used for the enhancement of load capacity

A catenary that is turned “upside down” yields the optimal form for an arched bridge, where the pressure at each point is distributed evenly on both sides. Fig. 5.33 shows a model and its practical execution in the Gaudí museum in Barcelona. Fig. 5.34 shows a much bigger version.

192

More about conic sections and developable surfaces

Fig. 5.34 A catenary turned on its head as a sturdy girder

▸▸▸ Square wheels

Fig. 5.35 A bumpy road and a square wheel can mutually “neutralize each other”.

An interesting – though academic – question: How would a road have to be constructed for a square wheel to be able to roll without vertical motions of its axis (Fig. 5.35)? The solution can, for instance, be found in [?] – it happens to be an upside down catenary. ◂◂◂

How many elements do we need in order to determine a conic section? Ellipses and hyperbolas are defined by five points or five tangents, parabolas by four. ⊕ Remark : We will refrain from providing an exact geometric proof. From an analytic standpoint, we must (in general) solve a system of linear equations with six variables – the coefficients of the conic section’s equation formula, Formula (5.1), for which only the ratio a1 ∶ a2 ∶ . . . ∶ a6 matters. Given five points or five tangents, it is possible to precisely construct as many additional points and tangents as necessary. This requires the mutually dual theorems of Pascal and Brianchon are required, which we will not prove here. Pascal ’s Theorem is illustrated in Fig. 5.41 and in Fig. 5.36 at the right – a simple linear construction for an arbitrary additional point of the conic section is plainly visible. ▸▸▸ The theorems of Pappus and Pascal Pascal ’s theorem reads as follows: For every hexagon inscribed in a conic section, the intersection points of pairs of opposite sides are collinear (Fig. 5.36 to the right, Fig. 5.41). The converse of this theorem is true as well. Pascal hexagons, that is, hexagons whose intersection points of opposite sides are collinear, are always

5.2 Conic sections

193

inscribed in some conic section. The existence of a Pascal line is, thus, not only necessary, but sufficient for a hexagon to be inscribed in a conic section. The theorem

Fig. 5.36 Left: Theorem of Pappus; Right: Theorem of Pascal

does not only apply for all ordinary conic sections, but for degenerate ones as well. Furthermore, it is particularly important in projective geometry in general. However, from a historical perspective, Pappus’ theorem is much older. ◂◂◂ ▸▸▸ The theorem of Brianchon Charles Julien Brianchon proved a theorem that turned out to be the dual of Pascal ’s theorem (Fig. 5.37, left): For every hexagon that is circumscribed about a conic section, the three lines joining opposing vertices pass through a common point. Conversely, if a hexagon possesses a Brianchon point, then it is circumscribed about a conic section.

Fig. 5.37 Theorem of Brianchon(on the left) and an interesting configuration (on the right)

By changing the names of the points or tangents of the conic section, one generally obtains a new Pascal line or Brianchon point. In general, one can find sixty Pascal lines and Brianchon points (Fig. 5.37 on the right). There are four such lines through each Brianchon point and four such points that lie on each Pascal line. ◂◂◂

194

More about conic sections and developable surfaces

Fig. 5.38 Two conic sections sharing four points. Center right: A parabola is defined by four points. (Actually there may be two parabolas on four points.) Far right: Circles automatically share two complex conjugate points at infinity (marked by crosses).

Only four points or tangents are required for a parabola because the straight line at infinity is automatically a tangent and thus a fifth element. However and in general, there exist two solutions, pictured in Fig. 5.38 on the right. ⊕ ⊕ Remark : A parabola “in standard position” (the axis is either parallel to the xor y-axis) is defined by three elements. It is then possible to recognize not only the tangent at infinity but also the respective contact point (in the direction of the axis). If one point and its respective tangent are known, we speak of a line element. In general, a parabola is, thus, defined by two line elements. ⊕

⊕ Remark : The question as to how many points are required to define a conic section uniquely can be answered very quickly in the algebraic sense – by making use of analytic geometry. There, a curve of degree two is defined by six parameters, one of which can be picked arbitrarily. This means: If the coordinates of five points are inserted into Formula (5.1), we get a system of linear equations with five variables, which can be solved uniquely. ⊕ ⊕ Remark : As was proven analytically in [9], circles always share two complex conjugate points at infinity. Despite our intuition to the contrary, this explains many apparent contradictions. It is now clear why a circle (which is a conic section) can be defined by only three points: The two missing points are the so-called “absolute points,” and they always belong to the circle (see also p. 151 and p. 276). ⊕

When do we get an ambiguous solution? If five elements of the same type (e.g., five points or five tangents) are given, then the conic section is defined uniquely. If the given elements are of different types, then there exist two solutions (mixing proportion 4 ∶ 1) or four solutions (3 ∶ 2). Let us leave aside the exact reasons and simply solve a few of the many possible combinations.

The inverse paper strip method An interesting possibility of “constructing” an ellipse is the so-called paper strip method (Fig. 5.39): On a strip of paper, we mark three mutually distinct points P , X, and Y . The paper strip is moved in such a way that X and Y move along the respective coordinate axes. Then, the point P describes an ellipse whose half-axes are of lengths P X and P Y . The proof is given in the chapter about kinematics. We

195

5.2 Conic sections

Fig. 5.39 The “paper strip method” and its inversion

can apply this knowledge in the following example: Given an axis, the apices, and an arbitrary point P on the ellipse, the missing apex can immediately be found by fitting a paper strip by means of a compass. If, for instance, half of the major axis a is given, then P Y is known, and X can be constructed. The distance P X = b is half of the minor axis. Ellipse and hyperbola with axes given by a line element The ellipse and hyperbola are symmetric with respect to both axes. Thus, if one point is known, three other symmetric points can also be found by mere reflection. A tangent yields three additional tangents, and thus, the declaration appears to be over-determined. Due to symmetry, however, this does not produce a contradiction. Let us consider the line element in the first of four quadrants defined by the axes. For the sake of clarity, let us define the axes as the x- and y-axis without declaring which of these is the major axis. The intersections of the tangent t with the axes shall be called X and Y . Depending on where these points lie, an ellipse or a hyperbola is to be expected. In the “elliptic case,” we can (for instance) use an affinity of the ellipse to one of its apex circles. The x-axis should be its axis of affinity. X remains static and the ray through the given point P will intersect in the “circle field” at a right angle. The respective point P ∗ on the circle can thus, firstly, be found at the Thales circle above M X and then, secondly, at the affinity ray orthogonal to the x-axis (the affinity axis). Now, the circle around M can be drawn through P ∗ . The apex of the ellipse can be found at the intersection of the affinity axis. The other apices can be found by completion. The principal apices can only be determined after that process. In the case of a hyperbola, we should imagine a solution that may not be the shortest (when counting lines) but represents an interesting combination of the aforementioned considerations: We first determine an ellipse that passes through the given point P and possesses a tangent there that is orthogonal to the tangent t. This ellipse is confocal to the desired hyperbola. The focal points F1 and F2 are thus given, and the hyperbola is more or less finished.

196

More about conic sections and developable surfaces

Fig. 5.41 Pascal’s theorem allows the linear construction of further points X – which may be located on a straight line x passing through 3 – given five points 1, . . . , 5 by means of the Pascal line p, which is defined through the auxFig. 5.40 Spatial interpretation of a conic sec- iliary points U = 24 ∩ 35 and V = x ∩ 14 tion construction (⇒ W = p ∩ 15 ⇒ X = 2W ∩ 3V ).

▸▸▸ Construction of conic sections via spatial interpretation In some cases, when specific constellations are given, the solution can be approached by spatial interpretation. The following example is already quite sophisticated: Three points A, B, C and two tangents s and t of a conic section are given. The lines s and t can then be interpreted as outline generatrices of a right cone of revolution in a front view. One of the two angle bisectors is then the front view of the cone’s vertical axis. (The initial situation is rotated according to (Fig. 5.40).) The base plane can be “pulled up” to an arbitrary height. Now, the top views of the three points A, B, and C can be augmented by the respective generators. The three points gain a spatial significance. They lie on the cone of revolution and span a plane ε, whose intersection curve with the cone not only contains A, B, and C, but also touches the cone’s generators s and t. In the front view, we see these points as contacts – as is the case with all other planar intersection curves whose carrier planes do not appear as straight lines. However, the augmentation of the points is ambiguous. For each point, there exist two possibilities – 8 combinations in total – of which certain pairs possess the same front views. Thus, we can expect four different planimetric solutions. An arbitrary constellation is chosen in Fig. 5.40. In order to make the plane ε appear as a line, we augment the horizontal principal line through C onto the straight line AB (auxiliary point 1). A side view with the viewing direction 1C yields the desired appearance of ε. Not only the principal vertex (as a point on the space curve) can immediately be

197

5.2 Conic sections

found but also the contact points with the given tangents (the outline points in the front view, such as T ). ◂◂◂

Construction of the conic sections

Fig. 5.42 Pointwise construction of the conic sections

When conic sections are constructed, the osculating circles in the apices should likewise be drawn. The constructions are shown in Fig. 5.42 without proof. The ellipse always remains inside the larger and outside of the smaller osculating circle. The transition of the curve from one osculating circle to another should occur “harmonically.” The plotting of arbitrary points is rather counterproductive, however, since the increased demand for drawing precision may disturb the overall balance of the curve. The parabola can be seen as an ellipse with one apex and one focal point at infinity. As it detaches from the osculating circle, the hyperbola gradually approximates its asymptotes. If a hyperbola is to be sketched, the asymptotes must always be considered! Arbitrary points are constructed by applying the definition of conic sections with the use of the focal points. In the case of ellipses, the sum of the distances from the focal points is constant. For hyperbolas, the magnitude of the difference stays constant. For parabolas, the distance to the focal point is equal to the distance from the director . The tangent at the constructed point always bisects the angle of the focal rays. ▸▸▸ What does an ancient column have to do with an ellipse? Ancient (Greek and Roman) columns are no ordinary cylinders of revolution – they are “thicker” in the middle. In fact, instructions for the construction of the meridian were found carved in stone: A circular arc is to be constructed, then intersected with vertical lines, and finally, the vertical sections are to be multiplied (by a factor of 10, for instance). A circle whose ordinates are multiplied is, in fact, an ellipse! ⊕ Remark : Rotating an ellipse is not enough to produce an ellipsoid. Such an object is only produced by rotating the ellipse about one of its two axes. For those who are interested: The result of a rotation about an axis-parallel chord is a surface of

198

More about conic sections and developable surfaces

Fig. 5.43 The production of ancient columns and what sometimes remains of them . . .

revolution which differs from a spindle torus by an affine mapping (Fig. 4.47). One could now argue that this is a mere splitting of hairs and that the exact shape of the column should be unimportant – as long as it is slightly thicker in the middle, who cares! But far from it! The ancient Greeks were enthusiastic “hair-splitters” in this regard, and the production of columns was quite an art of its own. For instance, columns at the corners of a building were slightly bigger – not for reasons of statics, but because they usually appear in backlight and thus give the impression of being thinner. ⊕ ◂◂◂

▸▸▸ “Angular distorted” conic sections If a cone of revolution that includes a planar oblique section is developed into the plane, then the section becomes a curve that, from an optical viewpoint, bears little resemblance to a conic section.

Fig. 5.44 “Angular distorted” conic sections and a resemblance of them, which is, however, entirely unrelated . . .

From a mathematical point of view, it is still a curve with a reasonably similar type of construction. It is produced from the top view of a conic section if the polar angle to the curve point is multiplied by a factor of t = g/w < 1, where g is the length on the cone’s generator seen in the top view, and w is its undistorted length. The radial distance must then be enlarged by a value of 1/t = w/g > 1. ◂◂◂

199

5.2 Conic sections

Fig. 5.45 Process of development of a cone of revolution (including a planar oblique section)

▸▸▸ Shadows on a wall Fig. 5.46 in the middle shows a situation from everyday life: A lamp casts a curved shadow. These are obviously conic sections, but how are they produced?

Fig. 5.46 Shadows on the wall

Solution: To be clear: The conic sections have nothing to do with the cone shape of the lampshade! The circular edges of the lampshade are the important parts. For example, let us look at the bottom edge. Due to the approximately pointshaped light source (the filament wire of the lamp), there exists a projection cone of revolution that intersects the wall along a conic section. The type of the conic section depends on the inclination of the wall with respect to the projection cone (the inclination of the cone-shaped lampshade is irrelevant). This is why the bottom shadow in Fig. 5.46 on the left is not a parabola (as could be spontaneously assumed) but a hyperbola. The same considerations are also applicable to the top boundary circle. In the general case, the projection cone is not the “extension” of the bottom cone (as in Fig. 5.46). We are thus faced with a second conic section that is independent from the bottom one. ◂◂◂

200

More about conic sections and developable surfaces

Fig. 5.47 Approximated parabolic trajectories

▸▸▸ Parabolic trajectory Fig. 5.47 shows a game that uses approximated parabolic trajectories. If an object is thrown in the air at an angle, then its trajectory (assuming no air resistance) will resemble a parabola. The special view in Fig. 5.47 gives the impression of a “jumping jet of water.” Irregularities in the parabolic arc arise due to several factors invisible to the naked eye (the image was taken using ◂◂◂ a very short exposure time).

Fig. 5.48 The orbits of planets are ellipses.

▸▸▸ Why are the orbits of planets ellipses? (Fig. 5.48) Kepler discovered this fact by means of very accurate measurements. It is hard to find a geometric explanation, since we actually need to solve differential equations ([16], see also https://www.researchgate.net/publication/ 228860752_SATELLITE_ORBITS). It took another 70 years until Newton provided the geometric proof. More on the orbit of our planet can be found in Chapter 11. ◂◂◂

201

5.3 General developables

5.3 General developables

Fig. 5.49 Seaweed as a typical example of general developable surfaces in nature

The third and last class of simple curved surfaces (next to the omnipresent cylinders and cones) is not very well-known. This is not surprising – these seldom spectacular surfaces often occur in a very hidden form; their outline is always straight (Fig. 5.49). As we have already said, developables are tangent surfaces of space curves. They are enveloped by planes – the osculating planes of the space curve. In the course of any type of spatial motion, each plane envelops a developable, a cylinder, or a cone. It touches the emerging surface at each position along a straight line (generator). Developables of constant slope

c Γ2 Fig. 5.50 A space curve c generates two surfaces Γ1 and Γ2 with given constant slope.

Γ1

202

More about conic sections and developable surfaces

Developables of constant slope are an important class among the developables. They are characterized by the fact that all their tangent planes are equally “sloped” and thus possess the same angle of inclination to a base plane. If we define the position of the generating plane β of a developable in such a way that it runs through the corresponding tangent t of a space curve c and has a given inclination to a fixed direction (e.g., the vertical coordinate axis), the plane will envelop a developable surface of constant slope. However, the task is ambiguous. If the tangent is not too steep, there will be two real solutions β1 and β2 that generate two surfaces Γ1 and Γ2 (Fig. 5.50). Surfaces like the ones describes above are not only of interest in theory, but also in practice. For instance, they are quite often used as stable transitions of road edges or for roof constructions. Sometimes they are deployed quite efficiently as tooth flanks (developable helical surfaces, see also Chapter 7), because the tangent plane along an entire generating line is constant and always has the same slope.

Fig. 5.51 Sand dunes as developables of constant slope

Such developables are found in sand dunes, contributing to their equilibrium: Sand is “trickling” down until a certain angle of inclination is reached (Fig. 5.51). At a certain angle, depending on the grain size, the friction of the grains is large enough for a state of equilibrium to set in.

Fig. 5.52 The sand dunes in the Namib are world-famous and the oldest dunes on Earth.

5.3 General developables

203

Let us think of the ridge of a sand dune. From each of its points, sand trickles down in all directions and forms a cone of revolution (cone of constant slope). The dune surface is enveloped by all those cones (Fig. 5.51 left). Pairs of adjacent cones intersect along a hyperbola that, in extreme cases, becomes a pair of straight lines passing through the tip of the cone. The dunes that are probably most famous around the world, and also of a very stable variety, are found in the Namib desert (Fig. 5.52, Fig. 5.53).

Fig. 5.53 Due to the wind, desert sand seems to shift constantly. The grains of sand in the Namib, however, have been sitting in the same place for at least a million years.

When planning roads through arbitrary terrain, the engineers rely on this insight: For the material used for construction (sand or gravel), the critical angles are known. The engineers now consider corresponding developables through the roadside and solve two problems at the same time: Firstly, the developables are stable and there will be no landslides, and secondly, the necessary motions of material are minimized (Fig. 5.54).

Fig. 5.54 Surfaces of constant slope in road construction

204

More about conic sections and developable surfaces

The generating curve c does not need to be a space curve. It can be planar and even lie in the base plane. In this case, the planes β1 and β2 and, therefore, also the surfaces Γ1 and Γ2 are symmetrical with respect to the base plane.

Fig. 5.55 Left side: Simple horizontal generating lines c of torses Γ1 with constant slope (left: circle, right: ellipse). The torses Γ2 are symmetrical with respect to the base plane. Right side: The two symmetrical torses are defined by a limaçon c in the base plane.

A trivial example is the surface of constant slope through a horizontal circle, which is a cone of revolution. If the generating line is a horizontal ellipse, however, the surface immediately produces selfintersections (Fig. 5.55, left). Fig. 5.55 to the right illustrates the case in which c is a limaçon of Pascal. The images on the right in Fig. 5.56 show that surfaces of constant slope can be used to solve the following problem of planar geometry: Given a curve c (for instance, a limaçon), what is the locus m of all points that have the same orthogonal distance from the curve? One possible solution works with surfaces of constant slope through c: Their straight parameter lines are equally inclined and perpendicular to the curve’s tangents, both in space and in the plan view (due to the law of right angle). If we project the spatial intersection line m of two neighboring surfaces onto the ground plane, we discover points on the desired locus m′ .

Fig. 5.56 Left side: The horizontal generating line c is a limaçon. Its midline m′ is a circle. Left: spatial solution, right: plan view. Right side: A function graph takes over the part of the otherwise much more complicated developable surfaces.

▸▸▸ Function graphs with constant slope In practice, it is generally hard to explicitly calculate the intersection line of the two different developables (Fig. 5.56 on the right). Therefore, finding a graphic solution that is easier to implement, is a better idea. The definition goes as follows: We consider a closed planar curve c in the (x, y)-plane and define a function graph Γ in the environment of c in such a way that each point is assigned a z-value that is the shortest distance from c. This graph

5.3 General developables

205

contains parts of the developable surfaces of constant slope which we have discussed in the previous section. The graph has arrises where two surfaces intersect. Whenever a part of one developing surface overlaps with a part of another surface, only points that are closer to the (x, y)-plane count.

Fig. 5.57 Left side: A set of closed lines and the corresponding function graph. The plan view of the arrises can be interpreted as “skeleton” of the boundaries. Right side: Instead of a base plane, one can also use a base sphere. Distances have to be measured on great circles, and heights have to be measured on straights through the midpoint.

The distance can either be always positive, or a negative value can be assigned to it if the point lies outside of the area defined by c. In any case the zero-manifold of the graph is the curve c. This kind of definition is very robust, even though it is computationally expensive, and allows to graphically determine midlines of arbitrary complicated lines. The projection of the arrises (in simple cases the “midline” or a “median axis”) of a more complex shape can be interpreted as “skeleton” of the boundary (Fig. 5.57 to the left). If we consider several closed loops, we can assign negative z-values for points that are outside of any given loop. When the loops are tiny circles (“zerocircles”), the plan view of the arrises results in the Voronoi diagram (Chapter 12) belonging to the scene, otherwise we can speak of a generalized Voronoi diagram. ◂◂◂ ▸▸▸ Star-shaped surfaces with locally constant slope The definition of the function graph Γ can be extended in a way that, instead of the (x, y)-plane, we consider a curved base surface Σ. We then have to measure distances along geodesics of Σ and find the corresponding points on the “generalized graph” on the normals of Σ. In the easiest case Σ is a sphere. Then the geodesics are great-circles. The generalized graph is sometimes called “star-shaped surface”: Associated with each normal of the sphere we have exactly one distance value, i.e., the shortest distance to the spherical curve. In Fig. 5.58 the outlines of a continent are chosen in order to create a new topology of the continent. Note that lakes, for instance, can significantly change the surface.

206

More about conic sections and developable surfaces

Fig. 5.58 Left side: A set of closed lines (continents and islands) and the corresponding star-shaped surface. The surfaces have locally constant slope with respect to the corresponding normals. Right side: The projection of the arrises of the star-shaped surface onto the sphere produces a “skeleton” of the boundary curves.

The curvature of the base sphere Σ in Fig. 5.57 on the right is comparatively small. In Fig. 5.58 on the left the starshaped surface does not consist of parts of developable surfaces any more. If we project the arrises of the starshaped surface onto the sphere, we get a skeletonization of spherical curves (Fig. 5.58 to the right). Similarly to planar curves, we can also generate spherical Voronoi diagrams (Chapter 12). ◂◂◂

How is a developable strip created? We know that, next to the “trivial” cylinders and cones, only a class of surfaces called developables can be developed. Let us take a rectangular strip of paper and attach the narrow edges to each other. The hereby generated ribbon is, of course, developable, since we cannot stretch or compress the paper without tearing it. If we do not twist the paper strip, then we get a cylinder. The midline of the strip is, thus, its normal section. Twisting produces a developable with the midline being a curve in space. ▸▸▸ Creating paper strips Is there a “paper strip” for an arbitrary space curve c so that c is its midline (Fig. 5.59, Fig. 5.60)? Let us consider three developables that are connected to the space curve: the tangential surface as the envelope of all osculating planes, the normal developable as the envelope of all normal planes, and the rectifying developable as the envelope of all rectifying plane (planes orthogonal to the principal normal). The midline c becomes a straight line when spread out in the plane and is, thus, a geodesic line on the developable. We know of these lines that the

207

5.3 General developables

σ

̺

P t c

Fig. 5.59 The rectifying developable of a space curve can be parameterized in such a way that the entire surface develops into a rectangular strip with the midline as the rectified curve.

Fig. 5.60 Rectifying developables of three space curves (blue)

osculating planes must be perpendicular to the tangent plane at any point (p. 142). The tangential surface, whose osculating plane is also its tangent plane thus does not qualify for our purpose. We can see from Fig. 4.37 on the right that the normal developable does not even carry the curve. This only leaves the rectifying developable, for which all the necessary conditions are met: The curve lies on the developable and is also geodesic line on it. Despite the fact that the development preserves angles, the generators of the developable do not meet the midline orthogonally. Quite the opposite: The only straight line in the rectifying plane which is orthogonal to the tangent of c is the binormal, and the locus of all binormals is not a developable. Thus, the method of intersecting two neighboring normal planes of the curve does not lead to the solution. ◂◂◂

208

More about conic sections and developable surfaces

Fig. 5.61 “Development of a developable”: How is it done? Center: Two congruent parts, one inside the other. On the right, one of these parts was developed.

▸▸▸ “Development of a developable” Every developable can be seen as the tangent surface of a space curve g. The curve g is known as the developable’s edge of regression. The tangents g are the generators of the developable. The development makes the edge of regression a planar curve g v . The generators of the developable are tangents of g, and thus, the corresponding lines in the development are the tangents of g v .

Fig. 5.62 Development of a developable which contains the Möbius strip. Each intermediate position is a developable, on which the jointly transformed strip is bounded by geodesic lines.

The edge of regression is seldom relevant in practice because, out of the infinitely large tangent plane, only the parts that do not reach the edge of regression are normally used. The edge of regression is meaningless with regard to the windmill in Fig. 5.61. Similar conditions apply to the oloid, whose development is depicted in Fig. 6.63, and to the development in Fig. 5.62. ◂◂◂ ▸▸▸ Approximation of a curved surface through rectangular strips A common technique (especially in shipbuilding) is to approximate moderately curved surfaces by means of developable strips.

5.3 General developables

209

Fig. 5.63 A curved surface is “modeled” from planks.

Wooden planks – but also aluminum planks, which are more commonly used under tensile loadings – are, for example, well-suited for “twisting and bending”. This system of modeling can be seen in Fig. 5.63. ◂◂◂

Let us generate arbitrary developable surfaces Architecture often demands the use of developable surfaces, and this is not surprising: The creation of such surfaces is much easier and cheaper than that of doubly curved surfaces.

Fig. 5.64 How architects construct curved and reasonably priced glass façades . . .

Some good news and some bad news: While it is always possible to find a developable surface connecting two arbitrary boundary curves, developable surfaces are characterized as always having straight-line contours. The connecting surfaces could, therefore, not have anything “curvy” or “spherical” about them. Therefore, in many cases, the surfaces would not be curvy enough. A program that performs direct modeling with developable surfaces – and can, nevertheless, achieve good results – is introduced on p. 360. ▸▸▸ Developable connecting surfaces Let c1 be an arbitrary curve in space and c2 a curve in a plane ε2 (Fig. 5.65). We will now introduce a procedure for finding the developable connecting surface Φ of c1 and c2 : We determine the tangent t1 for an arbitrary number of points P1 ∈ c1 , intersect it with the carrier plane ε2 , and draw a tangent t2 towards c2 from

210

More about conic sections and developable surfaces

Fig. 5.65 Construction of a connecting developable (on the left: oloid)

the intersection point T1 = T2 . The respective contact point P2 determines, along with the initial point P1 , a generator e of the surface Φ. The tangent plane of Φ is determined along the whole generator by the connection of e with t1 . Due to our construction, t2 also lies in the tangent plane – which is no contradiction. The thus defined series of tangent planes envelops a developable. This construction also applies if both c1 and c2 are planar curves.

Fig. 5.66 Centrum Bank of Vaduz (Hans Hollein) with cylinders as surfaces

If both curves c1 and c2 are space curves, the problem is more difficult but still solvable: Instead of the carrier plane ε2 of c2 , we now consider the tangent plane Φ2 of c2 . The tangent t1 at c1 should not be intersected with the plane ε2 but with Φ2 – a task for which we need a computer! An interesting example of a special connecting developable is pictured in Fig. 5.66. Here, the directrices lie in parallel planes. In such cases, the generators of the connecting developable are the straight lines connecting the points on both generators in which the tangents are parallel to the directrices. However, the image on the right indicates that all generators are parallel

5.3 General developables

211

– and thus, a cylinder is given. The image is based on a cylinder that was intersected with the side surfaces. ◂◂◂ ▸▸▸ The connecting developable of two circles Let us consider two circles c1 and c2 in different non-parallel planes ε1 and ε2 (with the section line s). If the circles are not accidently circular sections of quadratic cones, we can find the connecting developable according to our rules: Choose a point P1 ∈ c1 , intersect the corresponding tangent t1 with S (point T ) and find the two tangents from T to c2 . Choose one of the contact points (T2 ). Then the line T1 T2 generates the desired developable. Fig. 5.67 shows a practical application in architecture by W. Tschapeller.

Fig. 5.67 Wolfang Tschapeller’s vision of the “Vienna Museum” (2015). The buildings consist of developables that connect circles.

Fig. 5.68 shows how two sets of n circles can be connected using the described method. Note that all contours are straight lines, which indicates that we are dealing with developables. In this special case the 2n surface parts are all congruent.

Fig. 5.68 If n larger and n smaller circles are evenly distributed in meridian planes, they can be connected by a series of 2n congruent developables.

212

More about conic sections and developable surfaces

Fig. 5.69 shows two additional views of the object which is inscribed to an outer torus and circumscribed to an inner torus (tori will be discussed in greater detail in Chapter 6).

Fig. 5.69 Two more different views of a “torus-like object” (some part surfaces are removed).

Max Klammer, one of Tschapeller’s students, investigated the development of part surfaces like that, which resemble the development of conical frustums (Fig. 5.70). He connected them in the indicated way – first by “tooths”, later on also by paper clips and staplers.

Fig. 5.70 Max Klammers investigations of the development

So far, the project does not appear to be extraordinary. Klammer, however, found out that the whole object can be interpreted as a machine that is able to revolve, as long as it stays “a little bit flexible” and only some parts of the surfaces are materialized (Fig. 5.71).

Fig. 5.71 Theoretically impossible – and yet it moves!

5.3 General developables

213

In the presentation of his diploma thesis, Klammer made huge models move to demonstrate that such objects can be used in “flexible architecture”. Funnily enough, the German word Klammer-Maschine means stapler in English, so we assigned his model an amusing name: the “Klammer-Torus”. ◂◂◂

Reflections on a developable surface

Fig. 5.72 A reflection of light rays on a plane

Reflections on curved surfaces are part of very sophisticated geometry. If all light rays that emanate from a point-shaped light source are reflected on such a surface, we get a congruence of rays which envelop a new surface: the so-called focal surface or caustic. In general, such focal surfaces are very complicated and full of “singularities”. In application p. 228, we shall discuss the reflection in a sphere. The problem is simplified significantly if the reflecting surface is only singlecurved: Cylinders, cones, and developables are touched by a fixed plane along a whole generatrix. Fig. 5.72 shows what happens during reflection on a plane: All light rays from a point-shaped light source (which – like the Sun – may be infinitely far away) through an arbitrary straight line of the plane form a plane. The reflected light rays are restricted to the reflected plane, which is itself determined by the straight line and the reflected light source. If the reflecting surface is single-curved, we can replace it along each generator by its tangent plane. As with the plane (Fig. 5.73), the following simple situation applies: All light rays that are reflected in a generator of a simply curved surface lie in a plane (the focal plane) which passes through the point that is reflected in relation to the tangent plane along the generator. If we now let the generator move along the surface Φ, we get a pencil of focal planes which envelop the developable. The focal surface of a developable surface is, thus, itself developable. To give a more concrete example, the focal surface of a cylinder is again a cylinder. In application p. 227, we will

214

More about conic sections and developable surfaces

Fig. 5.73 Reflection in a simple curved surface

find out more about the reflection in a cylinder of revolution. The locus of all light sources reflected in the tangent planes is a curve – the focal line. ▸▸▸ Shiny generators on aluminum cylinders Let us consider Fig. 5.73 on the right: One of the rays that are reflected along a generator appears as a point. We can now imagine parallel light and picture the surface from a greater distance, which causes the viewing rays through the points of the generators to be approximately parallel. Thus, every point on the generator “flashes up”, and the whole generator glows brightly. Such effects are often visible on turned parts of aluminum (cylinders of revolution or cones of revolution) and also on glass bottles in sunlight. ◂◂◂ ▸▸▸ Glowing curves We encounter the following situation with reflections in a plane: A developable surface reflects a light source (such as a spotlight or the Sun). All focal planes intersect the plane in a straight line. The focal lines envelop a curve – the intersection curve of the focal surface with this plane. Thus, the following applies: The reflection of a developable surface on a plane is a glowing curve. The curve glows because it focuses all light that interacts with the surface (and sometimes even causes heat effects). ◂◂◂ ▸▸▸ Light games in the water (Fig. 5.74): Everybody knows the fascinating, constantly changing reflection patterns of sunlight on the sides of boats or buildings. The focusing effect of the light rays is evident here. This permits us to speculate that the surface of moving water is only singlecurved. This is, in fact, true (though only approximately so) if the motion of water is caused by wind. In such situations, the emerging wave surfaces are (ideally) cylinders – and hence, single curved. However, we are also dealing with the reflections of waves on harbor moles and boats. This produces new cylindrical waves which overlap the original ones. Taken together, these circumstances create the ideal conditions for a beautiful spectacle. ◂◂◂

5.3 General developables

215

Fig. 5.74 Light games above water (left) and below water (right)

▸▸▸ Reflecting compact discs – and curious effects The curious reflections on CDs must have aroused the interests of many. Two things are apparent: Firstly, these reflections seem to be glowing straight lines that can swiftly change position (and essentially rotate about the midpoint of the CD). Secondly, all colors of the rainbow seem to be visible among the reflections. This cannot be caused by the tracks (of which there is actually only one): The same effect is visible on blank CDs.

Fig. 5.75 A CD reflects all colors of the rainbow.

Apart from mere reflection, other properties of light are at play here. Roughly speaking, we are dealing with interferences. CDs are essentially manufactured from plastic polycarbonate, one side of which is vaporized with an aluminum layer (the aluminum reflects the laser beam which reads the data). In order to prevent chemical reactions, the disc is then coated with transparent plastic. When a light ray passes through the plastic coating, a part of it is reflected on the surface. What remains is refracted at the surface based on the angle of incidence (and also splits up into its color components). On the other side of the plastic coating, at least by the time it reaches the aluminium layer, the light is reflected, as well as “refracted,” and the ray appears parallel (but slightly shifted) to the ray reflected on the first surface. Diffraction of the light rays also takes place due to the presence of an optical diffraction grating (many thousands of openings per inch). The reflected and (following the many consecutive reflections) slightly shifted light rays now interfere with one another. This may lead not only to the augmentation but also to

216

More about conic sections and developable surfaces

the cancellation of entire color components. Similar effects occur on butterfly wings and fish scales.

Fig. 5.76 This unusual photograph demands an explanation.

Fig. 5.76 definitely requires additional explanation. The photo was taken in a room on the top floor. The sun shines through a window in a sloping wall and almost illuminates one half of a slanted CD. One might expect only the illuminated half of the CD to produce a reflection on the sloping wall. In fact, the entire CD is reflected on the wall, but the reflection is divided perfectly in two halves, which also look different. A detailed explanation of this phenomenon falls within the remit of physics rather than geometry. ◂◂◂

5.4 Maps and “sphere developments”

217

5.4 Maps and “sphere developments” The dilemma regarding the development of doubly curved surfaces

Fig. 5.77 However you may look at it, the sphere is definitely not developable!

We know at this point that it is not possible to develop doubly curved surfaces – let alone a sphere! Every attempt to press the surface of a sphere into the plane ends with expansions and compressions, or with the tearing apart of the object altogether. The method of peeling tangerines pictured in Fig. 5.77 comes close to Walter Wunderlich’s approach in Fig. 5.78. The method in Fig. 5.77 on the right exhibits certain similarities to the approximation of the sphere by cylindrical strips in Fig. 5.78 (center). Nature occasionally solves the problem abruptly (Fig. 5.79), artists find their individual solutions.

Fig. 5.78 The “apple peeling method” by Wunderlich and an approximation by a cylinder

However, the development of a sphere would be important for so many applications – especially in cartography! It is obvious that the maps with which we constantly deal must have been produced by using certain tricks that accommodate the curvature of the sphere. This must necessarily have occurred at the expense of geometrical properties that are well known to us. See, for example, Fig. 5.81, which highlights those parts of the globe that are illuminated by the Sun at a given time.

218

More about conic sections and developable surfaces

Fig. 5.79 The “brute-force approach” sometimes works as well . . .

Fig. 5.80 Orange origami art (Gerda Tomaselli, according to http://okadas.com/promo.htm)

The situation in the left image is very clear: The shadow boundary of the globe is a great circle. The right image shows the respective situation in a relatively common world map, where geographic longitudes and latitudes are simply used as Cartesian coordinates. The great circle becomes a wave-like curve (but not a sine wave). With such transformations, it is very simple to find a geographical position. However, the benefits of such a map already end here: Angles, lengths, and areas appear greatly distorted. This is especially evident in polar regions – around the equator, distortions tend to be the smallest. ▸▸▸ Is it developable after all? Architects are usually keen on building models of their sketches. Nowadays, they mostly employ state-of-the-art modeling software for this purpose. If

5.4 Maps and “sphere developments”

219

Fig. 5.81 The shadow boundary in the distorting coordinate grid

Fig. 5.82 A slightly unusual “development” of a sphere . . .

they then activate the “develop” function of such a software package, the computer will be up to the task. In the case of a sphere, a strangely frayed object will emerge. Upon closer inspection, it turns out that this object consist of ring sectors. Why is this the case? Fig. 5.82 illustrates the spatial situation: The sphere is more or less accurately approximated by frustums of cones of revolution. Each single frustum is developable, producing a ring sector. The better the approximation, the more circular rings are produced. As original as this idea is, it is not applicable to cartography: One only needs to imagine a world map where all the continents are “dissected” on separate strips . . . ◂◂◂

An angle- and circle-preserving projection We now consider the so-called stereographic projection of the sphere. It is a central projection with the center of the projection on the sphere, and the image plane is (for example) the opposite tangent plane. This kind of projection plays an important role in cartography due to the following properties: After stereographic projection, intersection angles and circles are preserved. Proof : Let a point Z on the sphere be the center of the stereographic projection from the sphere to the plane and π be the tangent plane through the antipode of Z.

220

More about conic sections and developable surfaces

Fig. 5.83 Stereographic projection of the globe from the South Pole

Without loss of generality, we may assume π to be horizontal. The straight lines of π correspond to circles through Z that result from the intersection of their connecting planes with the sphere. Let us take a closer look at two such straight lines a and b with the intersection P and the enclosed angle ϕ. They correspond to two circles ak and bk on the sphere through Pk and Z.

Fig. 5.84 Stereographic projection of the globe from the antipode of Vienna

Due to symmetry, the angle enclosed by both circles on the sphere is the same in both common points. However, the angle enclosed by ak and bk at Z equals ϕ, because the respective circle tangents lie in the horizontal tangent plane of Z and are, thus, parallel to a and b. Therefore, ak and bk also intersect in the point P k at an angle of ϕ. Whatever is true for the angle between two straight lines is also true for the angle enclosed by two curves, since the angle between curves is defined as the angle of the respective tangents. We have thus shown that stereographic projection preserves angles. It is also said that stereographic projection is conformal. We must briefly elaborate on the proof that stereographic projection also preserves circles: Stereographic projection on π is basically no different from a central projection on π – under special consideration of the points on an auxiliary sphere, which was placed “between” the center and the image plane (more precisely: the restriction of a central projection to the sphere). It is not forbidden to project points or

5.4 Maps and “sphere developments”

221

straight lines that do not lie on the sphere. In general, however, the preservation of angles and circles only applies to sphere elements. Let kk be a circle on the sphere. We now observe a cone of revolution that touches the sphere along kk . It has the apex Sk and nothing but generators that intersect the circle on the sphere at right angles. Let us project Sk from Z towards S ∈ π. Then, the generators correlate to straight lines through S. On each such straight line, there exists the image of a point of kk . The preservation of angles applies there (and only there). As on the sphere, the tangent of the projection k ∈ π of kk must intersect the projected cone generator orthogonally. However, there exists only one type of curve that intersects a pencil of rays orthogonally: the circle. Moreover, S must be the midpoint of this circle! ⊕ Remark : If the sphere circle kk passes through the center Z, then the apex Sk of the “adjacent” cone of revolution is located at the same height as Z. Its projection S is, therefore, a point at infinity. The pencil of rays of the projecting cone generator becomes a pencil of parallels. The projected curve k becomes a straight line that intersects this pencil orthogonally – but also, if you like, to a circle with its “center at infinity.” ⊕ ⊙

A practical map

If the points on the globe are projected from the center of the globe onto an arbitrary tangent plane, we get a world map where all planes – including the great circles – appear as straight lines through the center. However, great circles are (as we will soon discover) the shortest connecting paths between two points on the sphere surface. On such a map, it would thus suffice to connect two points with a ruler in order to draw the shortest path (Fig. 5.85).

Fig. 5.85 From Tunis to Tokyo

As remarkably simple as this principle may be, it produces a very significant map distortion, because the center of projection is relatively close to the projection plane. If, for instance, the northern hemisphere was projected

222

More about conic sections and developable surfaces

onto the tangent plane of the North Pole (many airplanes choose routes far up north on long-distance flights), then the entire southern hemisphere (including the equator) would not even appear on the map. Even the latitudes south of the 30th parallel would lie very far outside of it. ▸▸▸ From Bangalore to Buenos Aires The pragmatic American architect Richard Buckminster Fuller came up with his own solution to the problem of flight paths in his own way (Fig. 5.86):

Fig. 5.86 With Buckminster Fuller on the cuboctahedron from Bangalore to Buenos Aires

He projected not onto the plane but onto the side surfaces of a cuboctahedron that was ingeniously designed to fit onto the Earth and consists of eight equilateral triangles and four squares (the name derives from a combination of a cube and an octahedron). By complete accident, the continents turned out to fit relatively well on the surfaces of the polyhedron. If such a cuboctahedron is developed in the plane, one gets a map that is not very distorted (but not connected either). On this map, the shortest flight paths appear as straight lines as long as one remains within the side surfaces. The kink happens upon transition to the next surface. However, within continents, the flight routes are very easy to find. ◂◂◂ Stereographic projection offers a theoretically interesting solution to the flight path problem. On a map constructed by such a projection of the globe, the longitudes and latitudes appear as circles due to the preservation of angles and circles – with each circle of longitude intersecting each circle of latitude perpendicularly. The shortest paths between two points are, thus, also circles that must fulfil a certain condition that we will determine shortly. By defining a circle, one also knows the course angle at every point of the flight or ship path.

5.4 Maps and “sphere developments”

223

▸▸▸ The shortest connection In a stereographic projection, the shortest path between two distant globe points A and B is to be determined.

Fig. 5.87 The shortest path in a stereographic projection

Solution: The shortest path from A to B on the sphere is a great circle (Fig. 5.87). It is unambiguously defined by the carrier plane ABM (M being the midpoint of the Earth). If two arbitrary great circles are intersected, then the intersection points lie antipodal (relative to M ). In stereographic projections, great circles are, thus, circles that pass through two opposite points on the inversion circle (which is the image of the equator). According to the theorem concerning the constant power of a point regarding a circle (p. 16), we thus know the product of the distances on the secants through M (through A as well as B). This way, two additional points A and B on the great circle in question can be determined (though only one is sufficient for construction). ◂◂◂

The inversion at a circle from a “higher perspective” Let us once again return to the inversion in the plane. As interesting as it might have been theoretically, it still seemed a little bit arbitrary. Does the transformation M P ⋅ M P ∗ = r2 actually have a “higher” significance? Let the equator plane π be the image plane of the stereographic projection and the North Pole Z be the center of projection (Fig. 5.89). Furthermore, let S denote the South Pole. Pk and Pk∗ are two points on the sphere with the same orthogonal projection (top view) in π. The points Z, Pk , and Pk∗ now lie on the same great circle, which we shall, from now on, imagine as the sphere outline. Let P and P ∗ be the respective stereographic images of P and P ∗ . The points Pk , P ∗ , and S thus lie on a straight line (reflected in π) which, according to Thales’s theorem, is perpendicular to P Z. For the following simple calculation, let us imagine a two-dimensional coordinate system with the center M of the sphere as its origin, the x-axis in the direction of P , and the y-axis in the direction of Z. If x0 denotes the x-coordinate of P , then the straight line P Z has a slope of − xr0 (r = sphere

224

More about conic sections and developable surfaces

Fig. 5.88 A beautiful spatial interpretation of the inversion

Fig. 5.89 Inversion and stereographic projection

radius). The slope of the straight line Pk S is, thus, xr0 and its equation is, therefore, y = xr0 ⋅ x − r. In order to preserve P ∗ , we only need to intersect it with the x-axis: x0 ⋅ x − r = 0 ⇒ x0 ⋅ x = r 2 . r This already shows that P and P ∗ are inverted in the circle around M with the radius r. If the tangent plane at S is chosen instead of π as the image plane of the stereographic projection, then all image lengths are doubled, and we arrive at the following theorem: Let π be the horizontal drawing plane in whose origin a sphere with diameter 1 is centered. If overlapping points on the sphere are projected from the topmost point of the sphere onto π, we get points which form an inverse pair with respect to the unit circle in π. ⊕ Remark : Strictly speaking, the theorem would later have to be formulated as follows: Let Z be a point on the sphere, π be the tangent plane of the sphere in the opposite point, and k0 be the great circle of the sphere parallel to this plane. Then,

5.4 Maps and “sphere developments”

225

both hemispheres (bounded by k0 ) are mapped via the central projection from Z to π onto point fields which are related by an inversion with respect to k0 . ⊕

This admittedly far-fetched inversion of the plane is considerably easier for a three-dimensionally thinking being – it is merely the reflection of a sphere half in a plane. The “missing link” is a stereographic projection. Of course, we could now think about whether or not a four-dimensionally thinking being would find it equally easy to invert three-dimensional space in a sphere – such as using the generalized stereographic projection of space onto a “hypersphere”. It is, indeed, possible to extend this line of reasoning, and from a mathematical standpoint, it works! The only catch: Calculating such a phenomenon is perfectly feasible, but imagining it is no longer possible. From a higher perspective, the most important properties of inversion can easily be proven: Inversions map circles to circles and preserve angles. Straight lines correspond to circles through the midpoint of the inversion circle. Proof : Preservation of angles (conformality) and preservation of circles alike are deducible from the respective properties of the stereographic projection, which is applied twice (in opposite directions). Likewise, the reflection in the sphere does not affect the section angles or the circle property. In the case of stereographic projection, straight lines correlate with circles through the projection center (the intersection circle of the image plane with the sphere). They become circles through M during reflection and circles through M in an inverted stereographic projection. ⊙ ⊕ Remark : Another proof for the preservation of circles can be found in [9], where it is conducted in a rather elegant way by the use of complex numbers. The advantage of the geometric proof is, once again, the simple fact that its “residual products” promote geometrical comprehension. One piece of insight somehow always produces the other, eventually leading to a rounded geometrical “worldview,” which yields many conclusions whose proofs would otherwise have to be “derived” mathematically. ⊕

226

More about conic sections and developable surfaces

5.5 Reflection in a circle, a sphere, and a cylinder of revolution So far, we have often mentioned the reflection in a circle (for instance, with inversion), even though references to physical reflection were not always intended. The reflection in a surface which we know from nature follows two rules: Firstly, the incoming and the outgoing light rays lie in a plane which also contains the surface normal. Secondly, the angle enclosed by the normal and the incoming ray equals the angle enclosed by the normal and the outgoing ray (“angle of incidence = angle of reflection”). ▸▸▸ Reflection in a plane Let E be the eye point and S the point that emits light (Fig. 5.90 on the left). If we look into the reflection plane τ , we see a reflecting point R. We can determine R geometrically by reflecting S in τ and connecting this point S ∗ with E. The eye can no longer distinguish whether it is looking at the reflecting point R or the reflection point S ∗ . In fact, the two aforementioned rules are observed: SR and RE lie in a plane which includes the normal n, just as the angle of incidence ζ1 and the angle of reflection ζ2 are identical. The reflection in a plane is, therefore, a simple (linear) problem. ◂◂◂

Fig. 5.90 Reflection in curved surfaces

▸▸▸ Reflection in a curved surface Generally speaking, the reflection in a curved surface is, of course, a remarkably difficult undertaking in the general case. Let τ be a tangent plane in an arbitrary surface point R (Fig. 5.90 on the left). The point S in space can thus be reflected on τ . If, by coincidence, the straight lines ER and ES ∗ happen to be identical, then we have found the reflecting point of S in R (complicated surfaces may contain multiple “reflecting points”).

5.5 Reflection in a circle, a sphere, and a cylinder of revolution

227

Fig. 5.91 Reflection in a doubly-curved surface (Cloud Gate Chicago, Anish Kapoor )

In practice, we can find all reflecting points by conducting the aforementioned test for a high number of surface points. In cases where such reflection points are “almost” found, the immediate vicinities can be further scanned using ◂◂◂ approximation techniques. This generalized search method is, of course, computationally expensive – but we will not discuss it further here. In his diploma thesis, Franz Gruber developed a method for determining reflecting points as in Fig. 5.91 in “real time” (multiple images per second). Two special and somewhat frequent cases are interesting for us. ▸▸▸ Reflection in a cylinder of revolution Let Φ be a cylinder of revolution (Fig. 5.90 at the center), which, for the sake of simplicity, we shall imagine as being positioned vertically. If we project all points normally into the base plane, the problem of reflection is reduced to the two-dimensional reflection in the base circle. We now just have to find a point R′ , which, if seen from E ′ , is the reflecting point of S ′ in the base circle: The same angles in the base plane cause an equality of angles in the plane that is formed by E, R, and the cylinder normal n = M R.

Fig. 5.92 Anamorphoses: Reflection in the cylinder of revolution

228

More about conic sections and developable surfaces

⊕ Remark : The reflection in the cylinder of revolution, which is familiar to us from many halls with reflecting columns, was historically used to create so-called anamorphoses. The observer sees a bizarrely distorted image that appears “normal” when seen in a cylindrical mirror (Fig. 5.92). ⊕ ◂◂◂

▸▸▸ Reflection in a sphere

Fig. 5.93 Reflections in spheres

The reflection in a sphere can likewise be traced back to the reflection in a great circle: The sphere normal always contains the center M , and the light rays in question, ER and RS, lie in the great-circle plane M ES. ◂◂◂ Thus, the problem of trying to get a grip on the physical reflection in a circle is becoming more urgent. Let us say it upfront: The problem is not easily solvable because it can be shown that it would require the solution of an algebraic equation of degree four. This is not a problem for the computer (there are formulas for solving such equations), but it is generally unsolvable with just a ruler and a compass alone.

Fig. 5.94 The physical reflection in a sphere

A simple special case can be solved relatively quickly: If the point S (which is to be reflected) happens to be at the same distance from the circle (in practice, it would be from the sphere or the cylinder of revolution) as the

5.5 Reflection in a circle, a sphere, and a cylinder of revolution

229

eye point E, then the reflecting points Ri are located precisely on the angle bisector of M S and M E. Armed with this knowledge, we can easily locate the specular points in the eyes (Fig. 5.95) emanating from a light source. The location of the light source, on the other hand, is equally easy to reconstruct once we know the location of the specular points.

Fig. 5.95 Specular points on sphere caps

Even in the general case, we should not immediately give up. Let us shed some light on its “trappings”: ▸▸▸ Conic sections with given focal points that touch a given circle We know that in the case of conic sections, the curve tangents and curve normals bisect the angle of the focal rays. A light ray through the focal point E is thus reflected in another focal point S. If such a conic section touches a given circle k at the curve point R, then the tangent to the circle equals the tangent to the conic section at R, and we have thus reduced the problem to the reflection in a circle.

Fig. 5.96 Four confocal conic sections which touch a given circle

In order to find an additional point on the conic section in question, we now search for the point R on k, which is the reflecting point of S on the circle k with respect to E. In the case of the outer reflection, the solution seems

230

More about conic sections and developable surfaces

to be unambiguous, but it still cannot be done without the solution of a degree-four equation. Not all of the four possible solutions have to be real. We are dealing with four confocal conic sections (Fig. 5.96) which intersect each other orthogonally, as we have already proven. ◂◂◂

Fig. 5.97 The dragonfly dents the water surface in three points, which are immediately visible through the specular highlights.

The question still remains as to how the four “reflecting points” of S on the circle k can be geometrically determined for the given eye position (Fig. 5.98 on the left). The answer can only be: by trial and error. By moving R along the circle, the light ray ER is varied. The respective incoming light ray is always the reflection in relation to the circle normal and can easily be constructed. At some moment, S will change sides relative to this reflection – and the solution lies precisely there, with graphical accuracy.

Fig. 5.98 The reflected rays envelop a curve with cusps.

5.5 Reflection in a circle, a sphere, and a cylinder of revolution

231

▸▸▸ Focal lines of a circle The aforementioned method of “trial and error” produces a family of reflected rays which envelops a curve. The form of this so-called focal line (caustic) may vary. For points outside of the circle, it will look approximately as in Fig. 5.98 and Fig. 5.99. The term “focal line” is derived from the fact that instead of the eye point E, a line-shaped light source can be imagined, and then such brightly illuminated curves appear on cylindrically reflecting walls. A point E inside the circle k produces focal lines of the same type as in Fig. 5.100.

Fig. 5.99 Caustic with snout beetle. Note that the animal is directly in sunlight.

In each case, there exist, emanating from E, multiple (at most four) tangents of the focal line which lead to the desired reflecting points.

Fig. 5.100 The point may also be located inside the circle.

232

More about conic sections and developable surfaces

In reflections on the outer wall of the circle, only one of the four solutions is practically relevant. It can also be found by trial and error. If E lies inside the circle, then all solutions may actually be visible. Fig. 5.101 serves to illustrate why spatial inversion is often referred to as reflection in a sphere despite the fact that a real physical reflection in a sphere has nothing to do with it: Inversion gives us a well-defined spatial object, which is generated regardless of the observer (in this particular case, it is a Dupin cyclide, which is further discussed on p. 287). The reflected image which appears on the sphere changes its appearance with the location of the viewer.

Fig. 5.101 Inversion and physical reflection in a sphere

When put this way, the optical similarity of both images in Fig. 5.101 is only striking because the inverted object is observed from the right vantage point. By the way: M.C. Escher has approximated his spherical reflections by means of inversion. ◂◂◂

6

Prototypes

The majority of all curved surfaces cannot be developed into a plane. “In the neighborhood of a surface point,” doubly curved surfaces can bend in one direction, lying on one side of the tangent, as they do with spheres, or being bent in two directions and lying locally on both sides of the tangent plane, as is the case with saddle surfaces. By examining the simplest cases of doubly curved surfaces, i.e., degree-two surfaces, from the perspective of their behavior regarding the tangent plane, far-reaching statements about local curvature characteristics of all surfaces can be made. Surfaces that consist locally only of elliptic or hyperbolic points cannot be flattened out in the plane without deformation; they would need to be parabolic in all points. However, degree-two surfaces are not only interesting as prototypes. They possess a multitude of special properties with technical applicat ions. A classical example is the parabolic headlamp. Surfaces of revolution are the first type of more general surfaces to be discussed in the following sections. Aside from degree-two surfaces of revolution, the torus also plays an important role. This degree-four surface has numerous applications; it is not only generated by the rotation of a circle about a coplanar axis but also by the rotation of a sphere. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_6

233

234

Prototypes

6.1 Surfaces of degree two The simplest type of surface is a plane, which possesses one intersection point with every (general) straight line in space. It is therefore said that planes are degree-one surfaces (and there exists no other degree-one surface). Each surface that possesses two intersection points with a (general) straight line (these need not always be real and may also coincide) is called a quadratic (degree-two) surface. We are already familiar with several types of them: the sphere, the cylinder of revolution, and the cone of revolution. By applying affine mappings (which do not change the aforementioned number of intersections) to such surfaces, ellipsoids, elliptic cylinders, and quadratic cones can be produced. Through collinear mappings (which are also linear mappings that do not change the degree of the surface), paraboloids and hyperboloids, as well as parabolic and hyperbolic cylinders, can be produced. As we shall soon discover, it is impossible to distinguish between different types of cones produced by collineation, which is why they are generally referred to as quadratic cones. Doubly curved degree-two surfaces – ellipsoids, paraboloids, and hyperboloids (two-sheeted) – differ with respect to affine mappings, but there are collinear mappings that can transform them into a sphere. Single curved degree-two surfaces – elliptic, parabolic, hyperbolic cylinders, and quadratic cones – are affine and collinear with respect to the cylinder or the cone of revolution.

Fig. 6.1 Elliptic cylinders carry circular intersections.

Fig. 6.1 shows an interesting “experiment” with elliptic cylinders that are actually oblique circular cylinders: in contrast to the ellipse-shaped sections of cones of revolution, the single “hooves” can be twisted steplessly due to their circular shape. ▸▸▸ A new arm for Eva Inspired by geometric models like in Fig. 6.1, Philomena Strack, in her diploma thesis, designed a “new arm for Eva” (Fig. 6.2 and Fig. 6.3).

6.1 Surfaces of degree two

235

Fig. 6.2 Elliptic cylinders with a common circular section can successfully be used for prosthetic arms.

While the human elbow joint is a hinge joint that only has a single degree of freedom, most natural movements of the arm consist not only of bending the elbow joint, but also include a rotation of the lower arm. By recreating the elbow joint not as a hinge joint, but as a swivel joint, this single joint can replicate the combined movement and enables natural-looking movements of the prosthetic arm.

Fig. 6.3 Eva, the trial participant, confirmed that she felt very comfortable with the new arm.

The shapes of both the upper and the lower arm resemble that of an elliptical cylinder, which is more easily interpreted as a circular cylinder with approximately 45○ obliqueness (then, the elliptic cross section has the proportion ≈ 1.4 ∶ 1). The swivel joint comprises two congruent circular cross-sections of the upper and lower arm, ensuring the structural integrity of the prosthetic’s surface at every angle of the joint. In comparison, a hinge joint would open the surface while bending, and thus interfere with the design of the prosthesis. ◂◂◂

236

Prototypes

Ellipsoids As we already know, all cylinders and cones are developable because they are single curved. Ellipsoids, on the other hand, are doubly curved – just like spheres. In general, ellipsoids possess “three axes” but are not rotationally symmetric – they possess three pairwise-perpendicular planes of symmetry. By examining the ellipsoid that is produced by the rotation of an ellipse, one can distinguish between an oblate and a prolate ellipsoid (egg-shaped) of revolution.

Fig. 6.4 On the left: triaxial ellipsoid; on the right: ellipsoid of revolution, even though the parametrization suggests three axes.

▸▸▸ The shape of the Earth As is well-known, the globe is not precisely a sphere; it rather approximates an oblate ellipsoid of revolution, also called a geoid. The exact shape of the Earth corresponds to an ellipsoid with many tiny indentations and protrusions. These “blemishes,” including the oblateness at the poles, are highly relevant for physicists and geodesists. From a purely optical perspective, the Earth is practically indistinguishable from a sphere. ◂◂◂ Due to their affinity, ellipsoids “inherit” important properties from the sphere: Each planar section of an ellipsoid is an ellipse. The outline of an ellipsoid is an ellipse in cases of normal projection and can by any conic section in cases of central projection. ▸▸▸ Ellipsoids in dome construction Fig. 6.5 on the left shows the dome of the Reichstag in Berlin, which has the exact shape of a half-ellipsoid of revolution. Fig. 6.6 shows the normal projections as well as one central projection (perspective) of the dome. The cathedral in Florence is duly famous, not least for its dome (built by Brunelleschi , Fig. 9.2). However, the dome is not an exact ellipsoid – not

6.1 Surfaces of degree two

237

Fig. 6.5 An exact elliptical dome and “something similar” (Karlskirche, Vienna)

Fig. 6.6 The Reichstag dome in Berlin is a half-ellipsoid of revolution.

even approximately! In fact, it is approximated by cylinders that intersect along ellipses. ◂◂◂

Fig. 6.7 Aesthetic lamps “Queen Titania”, designed by Alberto Meda and Paolo Rizzatto. The lamps are perfect ellipsoids with three axes. Many artists are inspired by the aesthetics of ellipsoids.

238

Prototypes

▸▸▸ Ellipsoids in industrial design Fig. 6.7 and Fig. 6.8 show two examples of triaxial ellipsoids in Industrial Design. All the planar sections are ellipses.

Fig. 6.8 Elliptic fruit bowl (half of a triaxial ellipsoid) with parallel planar sections

Fig. 6.9 Spherical and ellipsoid-shaped teapot

Fig. 6.9 on the right shows Boris Sipek’s teapot in the form of an ellipsoid. Strictly speaking, the teapot resembles a “magic egg” given the various ways in which its individual pieces can be assembled together. Sipek deliberately uses affine transformations in much of his work. A spherical counterpart to ◂◂◂ his teapot is also available (on the left). ⊕ Remark : Mathematically speaking, degree-two surfaces are expressed by a socalled implicit equation of the form a1 x2 + a2 y 2 + a3 z 2 + a4 xy + a5 yz + a6 xz + a7 x + a8 y + a9 z + a0 = 0.

6.1 Surfaces of degree two

239

If a straight line with the parametrization x = u1 + t v 1 , y = u2 + t v 2 , z = u3 + t v 3 is intersected with the surface, an algebraic equation of degree two is found for the parameter t. Each of the two solutions corresponds to an intersection point.

Fig. 6.10 Convex surfaces but not of degree two

When counting intersection points, it would be unwise to rely on mere visual appearance. The convex surfaces in Fig. 6.10 (which possess neither indentations nor constrictions) seem to have at most two intersection points with any straight line. However, not every surface of a convex solid is of degree two. The surface on the right in Fig. 6.10 is, in fact, a supersphere with the implicit equation x4 + y 4 + z 4 = r4 . Therefore, it is a degree-four surface. The surface tangents in the six flat points touch the surface of a “higher degree”. In this case, a degree-two surface has enormous advantages for our deliberations: For instance, we then know that each planar section with this surface is a degreetwo curve – and therefore, a real or complex conic section (in general). This conic section may also degenerate to a pair of straight lines (real or conjugate complex) or a single straight line (always real) that should be counted twice. ⊕

Listening and focusing . . .

Due to their elegant form, egg-shaped ellipsoids of revolution are often found in design. Using the ellipse’s focal point property, a focusing lamp with a reflecting interior that resembles an egg-shaped ellipsoid of revolution can be created. It focuses all light that is created at the focal point of the lamp onto the second, non-materialized focal point.

Fig. 6.11 Wavefronts emanating from points inside the ellipse

Aside from light, other types of waves may also be focused this way, such as thermal radiation (burning mirror) and sound waves (Fig. 6.11). The focusing

240

Prototypes

works best if the source is located exactly at one focal point (left to center.) However, the phenomenon is not spoiled by slight deviations (right images). The figure shows the progression of wavefronts and enables us to observe interferences.

Fig. 6.12 Visible wavefronts

▸▸▸ Whispering bowls and odd acoustic phenomena Fig. 6.13 shows two opposing bowls in the library of Vorau Abbey in Styria (Austria). These two bowls resemble the cut-off caps of ellipsoids of revolution. Without having measured them precisely, one may assume that the bowls are spherical: The difference between the ellipsoid cap and the respective osculating sphere at the apex is practically negligible.

Fig. 6.13 Whispering bowls . . .

Fig. 6.14 . . . and soundscapes

By placing one ear close to a focal point, it is possible to hear words which have been whispered over 20 meters away near the other focal point. Fig. 6.14 shows an artistic version of the acoustic effect created by Bernhard Leitner. Paraboloids were used in that example – these, as we shall soon see, can be regarded as extreme cases of ellipsoids. Sound is projected towards the bowl from the focal points and is then focused parallel and directed towards a wall, where, after being reflected, the acoustic sensation appears at the ◂◂◂ angle of reflection.

241

6.1 Surfaces of degree two

Paraboloids

Fig. 6.15 Wavefronts of a parabola

Fig. 6.15 illustrates the reflection of wavefronts when using parabolas instead of ellipses. It shows that wavefronts are generated by plains when the starting point coincides with the focal point. A paraboloid of revolution can be constructed by rotating a parabola about its axis – Fig. 6.15 further illustrates the many technical applications of such surfaces as reflectors (radar screens, satellite dishes, radio telescopes, etc.). ▸▸▸ “Receiving dishes” (Fig. 6.16 left) In theory, a satellite dish has to be an exact paraboloid of revolution, and the receiving device has to be located exactly at its focal point. As with the whispering bowl previously mentioned, however, it is possible to approximate it quite well by means of an osculating sphere.

Fig. 6.16 Paraboloids of revolution as receivers or effective search lights

The only important requirement is that the receiver is not positioned at the center of the sphere but halfway between the center and the surface: The radius of the parabola’s osculating circle at the apex is twice the distance of the focal point to the apex. Since the receiver is not point-shaped to begin with, the devices allow for the axis of the bowl to be slightly different from the

242

Prototypes

signal direction. In such cases, it is required for the sensor to be positioned off-center (compare it to Fig. 4.56)! ◂◂◂ ▸▸▸ Parabolic headlights and sun collectors By positioning a point light source at the focal point of a reflecting paraboloid of revolution, it can be ensured that all light rays that hit the mirror will be reflected parallel to the axis. Such lights are called “long distance beams” (see Fig. 6.16 on the right).

Fig. 6.17 Parabolic headlights

Fig. 6.18 . . . and their inversion

Rod-shaped light sources are often used in practice. Parabolic cylinders are utilized in such cases (Fig. 6.17); they are also useful for focusing sunlight on a pipe. This pipe may contain liquid (e.g., thermo oil) which is first heated and then diverted. The screen is oriented in an east-west direction and is constantly moved to ensure that the Sun stays in its symmetry plane. ◂◂◂

Parabolic translation surfaces Paraboloids of revolution which have undergone affine transformations – in other words, elliptic paraboloids – are also degree-two surfaces. It is possible to get hyperbolic paraboloids by means of certain collineations. We prefer another definition: When a parabola is moved along a second, fixed parabola with a parallel axis and a different carrier plane, the moving parabola sweeps a paraboloid. If both parabolas open to the same side, we get an elliptic paraboloid, and otherwise, a hyperbolic paraboloid (Fig. 6.19). If one of the parabolas is not curved at all (and is thus a straight line), we get a parabolic cylinder. The two parabolas are interchangeable in terms of their function. Thus, the paraboloids carry at least two pencils of parabolas of equal importance (as we shall soon show, there exists an infinite number of pencils).

243

6.1 Surfaces of degree two

Fig. 6.19 Paraboloids as translation surfaces

⊕ Remark : A paraboloid in its standard position (containing the origin – the axis is the z-axis) can be described analytically by the equation z = A ⋅ x2 + B ⋅ y 2 . If A and B are of equal sign, then the paraboloid is elliptic – otherwise, it is hyperbolic. If A or B disappears, then we are dealing with a parabolic cylinder. If a paraboloid is intersected with an arbitrary plane y = k ⋅ x + d parallel to its axis, then the equation of the intersection can be given by inserting the plane’s linear equation into that of the paraboloid. This yields the equation of a parabola z = A ⋅ x2 + B ⋅ (k ⋅ x + d)2 = (A + B k 2 ) ⋅ x2 + 2Bkd ⋅ x + Bd2 . This means that each intersection with a plane parallel to the axis yields a parabola. Its curvature depends only on k, not on d. Thus, on this paraboloid, there exist infinitely many congruent parabolas that can be translated into each other for each position of the planes (as expressed by k).

Fig. 6.20 Hyperbolic paraboloids (HP bowl)

In the case of hyperbolic paraboloids, A and B have different signs, and A/B is neg√ ative. With k = ± −A/B, the coefficient of the quadratic term disappears and the section parabola becomes a straight line. This means that a hyperbolic paraboloid

244

Prototypes

Fig. 6.21 A hyperbolic paraboloid carries two families of straight lines, hyperbolas, and parabolas.

carries two families of straight lines, which appear as a grid of parallel straight lines if seen from the top. Let us summarize: ⊕

Each planar section of a paraboloid that is parallel to the axis is, generally speaking, a parabola. With hyperbolic paraboloids, the parabolas degenerate into lines for two particular positions of planes. Hyperbolic paraboloids, thus, carry two different families of straight lines, which appear parallel when projected in the axis direction.

Fig. 6.22 Hyperbolic paraboloid as the result of congruent rows of points

The boundaries of the surface in Fig. 6.22 are the generators that form a skew quadrangle. The rows of points formed by correlated points, i.e., points that are joined by generators, are congruent if the boundary generators appear

6.1 Surfaces of degree two

245

symmetric when viewed from above – otherwise, they are only similar. The following can, thus, be said: A hyperbolic paraboloid is also generated by congruent or similar rows of points.

Classically beautiful and very useful Paraboloids play an important part in surface theory, as all curved surfaces behave like paraboloids on a local level. We will discuss this in greater detail in the subsequent section. Hyperbolic paraboloids are also important in architecture, where they are simply called hyperbolic paraboloid s. They can, for instance, be used to roof rectangular areas in an elegant and very stable manner (Fig. 6.20). Their construction is particularly simple, as the wireframe can be created from straight rods.

Fig. 6.23 Skyscrapers with hyperbolic paraboloids as interior walls. (The picture in the middle shows the top view.)

Fig. 6.23 shows a sketch of twin towers designed by Paolo Piva where the lateral surfaces are derived from hyperbolic paraboloids.

Hyperboloids HP surfaces share the property of being able to carry two different families of straight lines with only one other type of surface: one-sheeted hyperboloids, which are also degree-two surfaces. A hyperboloid of revolution is formed by rotating a hyperbola about one of its axes. Depending on the axis of rotation, the result is either one-sheeted or two-sheeted. The two-sheeted hyperboloid of revolution (Fig. 6.25) is not as important in practice as the one-sheeted variant. It can be used as a lampshade for a

246

Prototypes

Fig. 6.24 Hyperbolic paraboloid at the Polytecnico di Milano. Note that, due to the thickness of the surface, the contour is not a conic.

precisely point-shaped light source (Fig. 2.5) because, due to the fundamental properties of conic sections, light that shines at a focal point is reflected in such a way that it appears to emanate from the second focal point (and, in the case of hyperbolas, from its extension). However, direct incidence of light would have to be prevented by local coverage, which ensures that no lighting occurs near the light axis.

Fig. 6.25 Two-sheeted hyperboloid of revolution from different perspectives

The one-sheeted hyperboloid of revolution is much more important in practice. It is generated not only by the rotation of a hyperbola about its conjugate axis but also by the rotation of a straight line about a skew axis. This not-at-all-trivial insight is attributable to Christopher Wren, the constructor of St. Paul’s Cathedral in London. ⊕ Remark : A hyperboloid of revolution with the axis z can be described by the equation x2 + y 2 z 2 − 2 = 1. a2 c

247

6.1 Surfaces of degree two

Fig. 6.26 Generation of a hyperboloid by means of a hyperbola

If it is intersected with a tangent plane x = a (parallel to the z-axis), then the equation of two straight lines can be found as y2 z2 c − = 0 ⇒ z = ± y. a2 c2 a A rotation gives us two families of straight lines lying in the plane.

Fig. 6.27 Double generation of a hyperboloid of revolution by means of rotating straight lines

Let us now consider an arbitrary point P in the plane. One straight line e from the first family and another line f from the second family pass through it. The straight lines e and f span a plane τ . The section of a plane with a degree-two surface is always a degree-two curve. This curve degenerates into two intersecting straight lines. Therefore, it could be said that e together with f forms a “degenerate” hyperbola. We now know two curves e and f through the surface point P (straight lines are degree-one curves which can, for instance, be deduced by their linear parameter representation). By definition, their tangents in P – the straight lines themselves – span the tangent plane, and thus, τ = ef is the tangent plane at P . Nothing changes in this statement even if we apply an arbitrary spatial affine mapping to the hyperboloid of revolution. We, therefore, arrive at the following: Every tangent plane τ of a one-sheeted hyperboloid intersects at a pair of straight lines e and f . Within each of the four sectors defined by e and f , the surface always stays on the same side of τ .

248

Prototypes

Following a similar train of thought, it can be shown that every non-degenerate degree-two surface that carries one family of straight lines {e} must also carry a second family {f }: Each planar section through e yields a degree-two curve which, nevertheless, possesses a “straight-line component” through e and must, therefore, degenerate into a pair of straight lines. Thus, it is clear that two pencils of straight lines must exist on HP surfaces as on hyperboloids. But what about cylinders and quadratic cones? The tangent plane τ touches not only at a single point, but along a whole generator. Thus, two “neighboring generators” (infinitely close together) lie on τ : The degree-two curve degenerates into a pair of identical straight lines. ⊕

Fig. 6.28 Barcelona and its affinity to hyperboloids: When arriving at the airport in Barcelona, the control tower (designed by Ricardo Bofill Levi) is the first hyperboloid you see. On the right: Antoni Gaudí’s model for the hyperboloids in the roof of the Sagrada Família (compare Fig. 6.29).

▸▸▸ The envelope of a rotating cube (Fig. 6.30) What happens when a cube rotates around a spatial diagonal (e.g. AG)? Solution: Of the twelve edges of a cube, three pass through A and G, intersecting the axis of rotation at the same angle (the angle occurs in congruent right triangles formed by the hypotenuse AG and the edge length or square diagonal). The three edges thus act as generators of one and the same cone of revolution, which is traced three times during their rotation. The three points B, D, and E or C, F , and H respectively form an equilateral triangle orthogonal to the axis of rotation, tracing one and the same hyperboloid of revolution six times. Three of these six edges belong to one family of straight lines and the other three edges to the other family of straight lines of the hyperboloid ◂◂◂ (Fig. 6.30 middle and right).

249

6.1 Surfaces of degree two

Fig. 6.29 Roof of the Sagrada Família in theory (middle) and practice

G C H D

Φ

F B

E A Fig. 6.30 A cube rotates around a spatial diagonal. Three points move on a circle. The edges that intersect the axis of rotation trace two cones of revolution. The remaining six edges, which are skew in relation to the axis of rotation, trace a hyperboloid of revolution.

▸▸▸ Result of rows of points on circles in parallel planes If one point moves on a circle and the second point moves on a circle in a parallel plane at the same angular velocity, then the connecting straight line generates a one-sheeted hyperboloid of revolution. If the respective circle tangents are parallel, a cylinder is produced (this also works if the circles are not positioned directly above each other – unlike in Fig. 6.31). It is also possible to consider a one-sheeted hyperboloid as the product of congruent rows of points on parallel circles. If the points move through their carrier circles in opposite directions, a new surface that is no longer of degree two is created. In the special case pictured in Fig. 6.31 on the right, a socalled circular conoid is generated, which we shall discuss at a later stage (Fig. 7.3). ◂◂◂

250

Prototypes

Fig. 6.31 Generating rows of points on circles in parallel planes

The fact that two independent families of straight lines lie on a one-sheeted hyperboloid of revolution has implications for practical applications. Stools of this shape (Fig. 6.34) have an enormous carrying capacity. The gargantuan cooling towers of power plants are also shaped like hyperboloids of revolution. This allows them to be stable despite having relatively thin walls. ▸▸▸ Stable and light-weight The cooling towers of many power plants have the shape of hyperboloids

Fig. 6.32 Cooling towers of a nuclear power plant. Their geometry would be perfect – events in the past, however, have proven that uncontrollable reactions occasionally occur in them. . .

of revolution. The ones depicted here (Temelin) are 155 m high and have a maximum diameter of 130 m. The diminution towards the top causes an increase in the speed of the hot water vapor. This leads – according to the aerodynamic paradox – to a diminution of pressure, which chills the steam. ◂◂◂ ▸▸▸ Generalization of the generation It may stand to reason that the double generation of a hyperboloid of revolution can be generalized by two rotating straight lines. In fact, the double generation works as long as the generating circles lie in parallel planes. The

6.1 Surfaces of degree two

251

Fig. 6.33 Generalization does not always work.

result is then a general hyperboloid (Fig. 6.33 left) that carries two families of straight lines. By “tilting” the circles, the two families of straight lines produce two different surfaces that have nothing to do with a hyperboloid (Fig. 6.33 center and on the right). ◂◂◂ Two congruent hyperboloids of revolution can, under some circumstances, fit together (Fig. 6.35). The surfaces touch along a generatrix. If one imagines both axes as fixed and allows one of the hyperboloids to rotate about its axis, then the other one would also have to rotate about its axis – given “glide-free friction”.

Fig. 6.34 Hyperboloids of revolution and – in the background on the bamboo stools – interesting “envelopments” on cylinders of revolution (see also p. 173).

In this way, the rotation about this axis can be transferred consistently onto a rotation about a second skew axis. In practice, this is used for the design

252

Prototypes

of so-called hypoid gears, despite the fact that such gears are not optimally suited for transferring rotations onto skew axes. This is due to the fact that hyperboloids do not roll but rather glide simultaneously along each other in so-called grinding motions. Involute gears, which we shall discuss in a later section, are found much more frequently. Their gear flanks are developables, allowing “instantaneous rolling” without gliding. Another highly original solution to this problem can be found in Fig. 11.18.

Fig. 6.35 Grinding hyperboloids of revolution

We already know that every degree-two surface intersects an arbitrary plane along a degree-two curve. The following can also be shown: The contour of a degree-two surface lies in a plane and is, therefore, a degreetwo curve. In the case of doubly curved surfaces, it is a conic section, and in the case of single curved surfaces, it is a pair of straight lines (as a rule). Proof : A doubly curved degree-two surface arises from a sphere by means of collineation. The inverse of the collineation allows us to transform such a surface back into a sphere. The center of the projection transforms into a point. At this point, the cone (of revolution) created by projecting surface tangents is centered. In the collineation, the circle of contact corresponds to the contour of the degree-two surface, which is, therefore, a conic section. By analogy, it is possible (using collineation) to transform a single curved degree-two surface back into a cylinder or cone of revolution. ⊙ ⊕ Remark : The contour of the hyperboloid of revolution in Fig. 6.35, a hyperbola appears five times, and an ellipse appears once. Fig. 6.25 illustrates that the contour of a degree-two surface does not always have to be real: In the image, no outline seems to exist for the two-sheeted hyperboloid of revolution. Mathematically speaking, a contour does, indeed, exist – but merely a complex one. Complex contours also occur if the center of the projection is inside the degree-two surface. ⊕

6.1 Surfaces of degree two

253

Whatever holds true for the contour also holds for the self-shadow boundary. It can be shown that any self-shadows of the surface’s boundary curves must also be conic sections: Self-shadow boundaries and shadows of a planar section of a degree-two surface onto itself are degree-two curves.

Fig. 6.36 The ellipse as a shadow on the inner side of a surface of degree two

⊕ Remark : The proof for this statement shall now be sketched: Let L be a light source and c the shadow-casting planar section of the surface Φ (a degree-two curve). Then, the projection cone Λ from L is a degree-two cone (in the case of parallel light rays, it is a degree-two cylinder). Λ ∩ Φ is to be determined. Firstly, according to Bézout’s theorem (p.169), a spatial degree-four curve is to be expected. However, this curve must already contain the planar section c – a degree-two curve. Thus, the remaining section, which is the shadow of c, may only be of degree two. ⊕

Fig. 6.35 illustrates this remarkable theorem. Shadows of hyperboloids on other hyperboloids are also visible, which are, in fact, more complicated space curves (of degree four). ▸▸▸ Geodesics on ellipsoids The Earth is almost a sphere, and therefore, geodesics on the Earth are almost great circles. Say, we want to fly along the shortest route from A to B. On a sphere, we somehow connect the Earth’s center M with A and B and get the great circle’s plane. Since we cannot see M directly, it is a good idea to take a third point C on the normal through A. The plane ε = ABC has to be intersected with the sphere. The angle of ε with the corresponding meridian plane indicates the starting angle of our airplane. If we want to fly back from B to A, we can take the third point C on the sphere’s normal through B, and of course, we get the same result. If we are overly precise , we have to say that the Earth is, in a better approximation, an oblate ellipsoid. In Fig. 6.37 we exaggerate the ellipsoid a little bit. Clearly, we can see that neither the method with the normal in A nor the one with the normal in B works. This results in to two different ellipses on the ellipsoid. The truth does not even necessarily lie in the middle, as we

254

Prototypes

⃗A n

⃗A n

A

A

B B ⃗B n

⃗B n

Fig. 6.37 Shortest connection: The normals nA and nB to the ellipsoid at the points A and B are skew. The red geodesic connecting A and B lies either between the blue and green planar sections through A and B, or even somewhere else.

can see in Fig. 6.37 (right). In general, a geodesic on an ellipsoid is not an ellipse. ◂◂◂ ▸▸▸ Saturn’s shape and its rings On Saturn (Fig. 6.38), which has an equator radius ten times that of the Earth and much more flattened polar regions (10% less circumference of the meridians!), this could make much more of a difference than on Earth when we look for geodesic lines as we did in the previous application.

reflections?

Sun Fig. 6.38 NASA photo of Saturn. The Sun is glancing through the atmosphere. File: Saturn HST 2004-03-22.jpg

Fig. 6.38 looks strange and definitely requires some more contemplation. Luckily, there exist comparable photos from other positions, like the ones in Fig. 6.39. Firstly, Saturn is an oblate ellipsoid and both the contour and the “terminator” (self-shadow border) are ellipses. The fabulous rings lie in the equator plane and can be considered to be completely flat. The shadow of Saturn onto its rings is, therefore, also an ellipse. The rings themselves cast shadow curves onto Saturn which are the intersection lines of oblique elliptic cylinders with the ellipsoid, i.e., they are space curves of degree four.

255

6.1 Surfaces of degree two

Fig. 6.39 Two more NASA photos of Saturn from Wikimedia Commons

Fig. 6.40 Computer simulation

Let us now look at the dark side of Saturn (Fig. 6.38), where there should be complete darkness. We are above the rings. The outer rings, however, are still partly visible, since they are illuminated (the sunrays are slightly refracted through the atmosphere). ◂◂◂ Cubic circle: When a degree-two cylinder is intersected with a degree-two cone, a spatial degree-four intersection curve can be predicted for the general case. However, if the cylinder and the cone share a generatrix, then this straight line is part of the curve. It splits off from the intersection. If both surfaces touch along this generator, then the remaining section is a conic section – otherwise, it is a spatial degree-three curve. Such a curve is visible in Fig. 6.41, where a cylinder of revolution and an oblique circular cone have been chosen. The result is called an upright cubic circle. When viewed from above, the curve appears as a circle, and in other projections as a degree-three curve. A cubic circle belongs to the simplest non-planar algebraic space curves and is, therefore, frequently employed for purposes of illustration. For interested readers: A possible parameter representation of the curve is given by x = r ⋅ cos u, y = r ⋅ sin u, z = h ⋅ tan u/2 (u ∈ [−π/2, π/2]),

256

Prototypes

Fig. 6.41 Cubic circle as an intersection curve

where r is the cylinder radius and h is a scaling factor for the height. A cubic space curve with an even simpler parameter representation is the cubic parabola x = t, y = t2 , z = t3 . ▸▸▸ Movements on and around triaxial ellipsoids Ellipsoids – and more generally degree-two surfaces – have many remarkable properties that are subject of numerous books ([22]). Two of them will be investigated in detail in the following paragraphs. The first consideration was only a conjecture until recently: For any given ellipsoid Φ, there is a three-parameter family of planes which intersect Φ along ellipses. However, the size of an ellipse depends only on its two semiaxes. Consequently, on each ellipsoid there exist ellipses with a one-parameter family of congruent copies on Φ. One can expect that some conics can even be moved on the ellipsoid.

Fig. 6.42 Congruent ellipses can be moved on a triaxial ellipsoid.

6.1 Surfaces of degree two

257

The proof for this statement, and also generalization to the other degreetwo surfaces, is given in [22]. Fig. 6.42 and Fig. 6.43 illustrate this non-trivial fact for two different triaxial ellipsoids. In every image all ellipses of the same color have the same ratio of semiaxes.

Fig. 6.43 With larger semiaxes of the congruent ellipses, larger parts of the ellipsoids are covered.

When an ellipse of a given size is moved along on the ellipsoid, one can observe the contact point of the accompanying parallel tangent plane. Its orbit stays the same for all ellipses with constant ratio of the semiaxes. If the ratio is 1 and the moving ellipse is a circle, the orbit degenerates to the umbilical points of the ellipsoid. Circular intersections can, therefore, not be moved. Another astonishing theorem, proofed in [22], states that all possible “bounding boxes” (circumscribed cuboids) of a triaxial ellipsoid have their vertices on a concentric sphere (Fig. 6.44 on the right).

Fig. 6.44 Ellipse with circumscribed rectangles (on the left) and ellipsoid with circumscribed cuboids.

This is the 3-dimensional version of the better known fact, that all rectangles that are circumscribed to an ellipse have their vertices on a concentric circle (Fig. 6.44 on the left, proof see [16]). ◂◂◂ ▸▸▸ Moving along the generator of a degree-two surface Without going into detail (please, again refer to [22]): If we move along a

258

Prototypes

generator of a degree-two surface (hyperboloid or hyperbolic paraboloid), the corresponding tangent plane will rotate about 180○ (Fig. 6.45).

Fig. 6.45 Moving along a generating line of a hyperboloid.

The rotation, however, is not proportional to the distance travelled. If we have a hyperboloid of rotation, the rotation angle of the tangent plane is proportional to the tangent of the distance, measured from the point with shortest distance to the axis of the surface. ◂◂◂

6.2 Three types of surface points

259

6.2 Three types of surface points In the previous section, we discussed the topic of degree-two surfaces extensively. This was for two reasons: Firstly, as we have seen, these surfaces have numerous practical applications. The second reason should soon become clear:

Curvature of a planar curve

Fig. 6.46 Curves with intricacies

Let us start with a two-dimensional comparison and imagine an arbitrary curve in the drawing plane (without intricacies such as tips, kinks, or jumps as in Fig. 6.46).

Fig. 6.47 Osculating circles of a bent planar curve

At each point P of this curve, there exists a tangent. It is the “linear approximation” of the curve at the point P . At each point, there also exists an osculating circle, which does a much better job at approximating the curve. It could be said that it represents a quadratic approximation. Depending on

260

Prototypes

the side on which the osculating circle is located, it is already possible to distinguish between positive and negative curvature. The smaller the osculating circle, the larger the curvature (Fig. 6.47).

Fig. 6.48 Osculating parabolas of a curve

Fig. 6.48 shows another kind of quadratic approximation of a curve. This time, osculating parabolas were used instead of osculating circles. Like osculating circles, they are each defined by three neighboring points as well as a fixed axis direction.

Fig. 6.49 Osculating circles and osculating parabolas (seals in the harbour of Capetown)

In space, curvature is not at all easy to define! Let us now try to extrapolate the procedure into space: If P is a surface point, then the corresponding tangent plane τ ∋ P is a linear approximation of the surface. However, what corresponds to the osculating circle? Let us consider an arbitrary surface tangent t ∋ P . There exist infinitely many space curves c in the surface with t as their tangent. The osculating circles may be different for various curves. Meusnier has shown that all the osculating circles of the surface curves defined by the line element (P, t) form a sphere,

6.2 Three types of surface points

261

the so-called Meusnier sphere (Fig. 6.50). The center of this sphere is also the center of curvature for the normal section of the surface through t.

Fig. 6.50 Meusnier spheres for different tangent directions

Principal curvatures The existence of the Meusnier sphere is remarkable in and of itself. Yet, what happens if we change t? Of course, this problem has already been investigated in great detail. However, the issue is very elaborate and does not yield any impressive visuals – it, thus, falls outside the scope of this book.

Fig. 6.51 Planar intersections parallel to the tangent plane, Dupin’s indicatrix

The following shall be presented without proof: At each surface point, there exists a greatest and a smallest Meusnier sphere. They belong to a pair of orthogonal surface tangents, so-called curvature tangents. Let us intersect the surface with a plane which is parallel to the tangent plane but only “infinitesimally” distant to it (Fig. 6.51). In an infinitesimal neighborhood of the surface point, the intersection curve with the surface can locally hardly be distinguished from an ellipse, a hyperbola, or a pair of parallels – known henceforth as indicatrices. The axes of the indicatrix are the principal curvature tangents. This also means that the curvature of all normal sections is known once the indicatrix is defined – more specifically, knowing the curvature along the principal curvature tangents is enough. This insight goes back to Dupin. Principal curvature lines are the surface curves where all tangents are curvature tangents and which, therefore, follow the direction of the strongest and weakest curvature.

262

Prototypes

Fig. 6.52 Principal curvature lines s on an ellipsoid with three axes.

There are two families of principal curvature lines. The curves from one family intersect all curves from the other family orthogonally (except at umbilics). If we consider a surface point and intersect the surface orthogonally to its tangent plane τ , we get ellipses or hyperbolas whose axes are parallel to the tangents of the curvature lines in τ . Fig. 6.52 in the middle shows curvature lines on a triaxial ellipsoid. It can be shown that the curvature lines are intersection curves with “confocal” hyperboloids (Fig. 6.52 on the right).

Fig. 6.53 Triaxial ellipsoid with a clever triangulation

Fig. 6.53 in the middle and on the right shows the design and the construction phase for the project “hangar8” (Volkmar Burgstaller). A triaxial ellipsoid is triangulated by being first cut into slices, after which the points of an intersection line are connected to the points of the next intersection line in a way that produces approximately equilateral triangles. Emphasis must be put on the word “approximately”, as unless we are dealing with very special polyhedra, no surface can be approximated only by congruent triangles Fig. 10.26 shows the same surface but from the inside. Fig. 6.53 on the left shows a perfume bottle by Guerlain (an ellipsoid of revolution), where a similar method of triangulation has been applied, with groups of six triangles being combined into hexagons.

Osculating parabolas lead to an important theorem The other approach would mean using osculating parabolas instead of osculating circles. They agree in curvature with any intersection of a plane through the surface normal. Like the osculating circles of the normal sections, they should be defined by three neighboring points on the normal sections. This time, the result – the surface formed by all possible parabolas

6.2 Three types of surface points

263

– is simple: It turns out to be either the tried and true paraboloid (elliptic or hyperbolic) or a parabolic cylinder! If we attempt to approximate the surface quadratically by using parabolas, we always get the same previously noted three surfaces. The approximation quality will improve, the smaller the chosen area where the comparison takes place. Thus, from a local perspective, there exist only three types of surfaces: Essentially, every surface of any conceivable complexity is locally, i.e., in a sufficiently small neighborhood of a point, curved like an elliptic or hyperbolic paraboloid or like a parabolic cylinder (Fig. 6.54). The surface point is, therefore, called either elliptic, hyperbolic, or parabolic.

Fig. 6.54 The three different types of surface points

⊕ Remark : Paradoxically, the two-sheeted hyperboloid consists only of elliptic points even though it carries a multitude of hyperbolas (Fig. 6.25). Even the contours (if real) appear as hyperbolas! ⊕

If we consider not only a “microscopic fragment” but the whole surface, then the issue becomes much more complicated. At the level of the whole surface, there are no limits to the possible variations. Nevertheless, it is still possible to speak of elliptic, hyperbolic, or parabolic curved parts of a surface. In general, the local properties do not change arbitrarily but continuously.

Fig. 6.55 The “saddle point” is always of a different type.

Fig. 6.55 shows three surfaces which, at first glance, resemble an hyperbolic paraboloid. At the supposed saddle point, the surfaces are differently curved

264

Prototypes

(elliptic on the left, parabolic in the middle, and hyperbolic on the right). In the neighborhood of the point in question, only the right surface is actually related to the hyperbolic paraboloid. This can also be seen due to the fact that the tangent plane “penetrates” the surface in more than just the contact point (just locally). In the case of the middle surface, there is also an intersection with the tangent plane, but this intersection does not occur in the immediate neighborhood of the point. The exact hyperbolic paraboloid and the one-sheeted hyperboloid of revolution carry only hyperbolic points, while convex surfaces (surfaces which envelop a manifold without indentations or neckings) are always either elliptically or parabolically curved. ▸▸▸ An exciting experiment Can a two-dimensional being on a surface find out to what extent its “carrier surface” is curved without leaving the surface and thus entering threedimensional space?

Fig. 6.56 The test using a circle

The mathematician’s answer is: Yes! The being would merely have to draw a circle with the radius r (Fig. 6.56) and measure its circumference. If this circumference is 2π ⋅ r, then the being lives on a parabolic surface – if it is greater, then it lives on a hyperbolic surface. A being on an elliptic surface – just like us humans on the globe – would see that the circle is smaller than expected. Let us check this by way of a specific example: We draw a circle around the North Pole with a radius of r = 10 000 km (a quarter of the Earth’s circumference). Thus, all points of the circle lie on the equator, which has a circumference of 40 000 km. It is, in fact, 2π ⋅ r ≈ 62 800 km, which means that our carrier surface must be elliptically curved – and quite strongly so. This mundane fact of contemporary science was assumed to be true for many centuries (and was prefigured by several great minds of the ancient world, such as Eratosthenes, who worked out the circumference of the Earth with remarkable accuracy 2200 years ago). The “rigorous proof” was not provided until the age of rocket science. ⊕ Remark : This experiment has an additional, particularly exciting extrapolation: Mathematicians can prove that it also works in any dimension. We can determine whether space is curved without entering the fourth dimension. However, it is actually not that simple. Globally, our space does not seem to be curved on a large

265

6.2 Three types of surface points

scale. Locally, however, there are lots of noticeable indentations in the neighborhood of large masses (such as black holes). ⊕ ◂◂◂

▸▸▸ Light edges Fig. 6.57 shows two surfaces of translation which differ only slightly: In the right image, a cubic parabola is being translated along a second cubic parabola. The surface is continuously differentiable to the second degree – even at the critical “midline” where the color changes. In the left image, a translated cubic parabola is being approximated by two regular parabolas which do not have a transition of constant curvature at their apex. A layman has to examine the images many times to notice that in the left, there are bends at the midlines next to the shadowing. Nevertheless, such subtleties play a great role in practice: In the construction of car bodies , light edges are mostly undesirable. Due to the reflective paint, car exteriors are visually very sensitive to such details. Looking for such defects can be compared to detecting indentations on a fly’s eye (Fig. 6.59).

Fig. 6.57 Curvature jump . . .

Fig. 6.58 . . . or not?

Fig. 6.58 shows two surfaces of revolution where two differently curved meridian circles are combined. The transition occurs on the left at an arbitrary point and on the right at the exact location where the tangents of the circle are horizontal. On the left surface, the change from elliptic to hyperbolic points comes abruptly. On the right, the horizontal tangential plane touches both partial surfaces along the common circle. Its points are parabolic for both partial surfaces. This is why the curvature jump in the right image, as opposed to the one in the left image, is not noticeable as a “light edge.” ◂◂◂ If a surface is composed exclusively of parabolic points, then the surface is only single and not doubly curved. There only exist a few classes of surfaces with this property, and they play an important role in practice: There are developable surfaces, which include the cylinder and the cone (see also chapter 5). They can be manufactured relatively easily by bending the “blank cut” without elongation or compression (Fig. 6.61).

266

Prototypes

Fig. 6.59 The light reflection shows an indentation on the fly’s eye.

The development of a Möbius strip. Each surface in between is, of course, also developable. Fig. 6.60

Developable surfaces can be visually recognized by their contours, which are composed entirely out of straight-line segments independent of the viewing direction. Here, one ought to be reminded of the contour generators of cones and cylinders (boundary curves are not counted as part of the contour – only the surface curves along which the tangent planes appear as a line segment). Some lesser-known examples include the developables of constant slope, which are used during street construction; the oloid (Fig. 6.63); and the Möbius strip (Fig. 6.61).

6.2 Three types of surface points

267

Fig. 6.61 Three different views of the Möbius strip

Fig. 6.62 Developable surfaces from different perspectives

▸▸▸ Revolvability with practical consequences The oloid (cf. Fig. 5.65 and 6.103), invented by the Swiss engineer Paul Schatz, is one of the developable surfaces with practical applications. It can be rolled along a table surface in a wobbling motion, which must be the reason for its common English name, the “wobbler” (Fig. 6.63 on the right).

Fig. 6.63 Left, center: Revolution of the oloid according to Paul Schatz (www.oloid.ch). Right: Development according to Stachel/Dirnböck (www.geometrie.tuwien.ac.at/stachel).

As a consequence, the oloid can be revolved in a rather unusual way (Fig. 6.63). If this revolution is conducted in water, it produces radiating currents that display a remarkably wide range. These can, for instance, be used to treat ◂◂◂ sewage water.

268

Prototypes

6.3 Surfaces of revolution Rotationally symmetrical surfaces play an important role in nature and technology. A surface of revolution is created by rotation of an arbitrary curve about a fixed axis. If the generating curve lies in a plane through the axis (meridian plane), it is called the meridian of the surface.

Fig. 6.64 Surface of revolution in theory and nature

If rotated, each point of the generating curve creates a circle of latitude (sometimes also called a parallel circle) of the surface. If the curve does not lie in the meridian plane, the axially symmetric meridian can be determined by intersecting all circles of latitude with a fixed meridian plane.

Fig. 6.65 Surfaces of revolution with meridians and circles of latitude (oblique axis)

If the meridian has a tangent parallel to the axis of rotation, then a rotation of the associated point produces a circle with a locally minimal or maximal

6.3 Surfaces of revolution

269

radius (e.g., equator circles, gorge circles, waist lines). In general, boundary circles do not belong to this group of circles. If the meridian tangent is orthogonal to the axis, the circle’s plane touches the surface along the entire circle. ⊕ Remark : During rotation, the tangent of the meridian generally traces a cone of revolution with its apex on the axis of rotation. Alternatively, it can be said that the surface is enveloped by a family of tangent cones. The surface can also be interpreted as the envelope of all cones whose apices lie on the axis and which also touch the meridian (Fig. 6.64 on the right). ⊕

Fig. 6.66 Two families of curves on a surface of revolution

Surfaces of revolution are invariant with respect to any rotation about the axis and reflections in an arbitrary meridian plane. If the generating curve is not a planar curve (Fig. 6.66), then, in addition to the curve itself, any curve reflected in an arbitrary meridian plane is a “generating” one. (Any curve on the surface of revolution generates at least a part of this surface.)

Fig. 6.67 Along each parallel circle of a surface of revolution, one can inscribe a sphere (left and middle) and a cone of revolution (right).

▸▸▸ Vase with an ellipse as its finishing part The lower part of the vase pictured in Fig. 6.68 is created by the rotation of

270

Prototypes

a sine wave. In the upper part, it is designed in such a way that its finishing part is an ellipse inclined towards the axis.

Fig. 6.68 Vase with an ellipse as an oblique finishing part

Now the question arises which surface of revolution allows this simple oblique intersection. Locally, it must be a degree-two surface of revolution! In this particular case, the surface is hyperbolically curved. In its upper part, the surface is a hyperboloid of revolution, and in the part near the oblique inter◂◂◂ section, it is almost a cone of revolution. ▸▸▸ Distorted wine barrel A wine barrel is a well-known surface of revolution and used to function as the starting point for a number of important calculations. Kepler , for instance, used it to develop a simple formula which is of high significance in mathematics (“Simpson’s rule”).

Fig. 6.69 Affinely distorted surfaces of revolution (original on the left)

Fig. 6.69 shows a “poster” of a visitor’s lounge: The wine barrel is affinely distorted. The visitor would only notice this when moving close to the object and viewing it from its side. On the right side, the same photo has simply been stretched planimetrically in its horizontal direction, which re-establishes the appearance of a surface of revolution. ◂◂◂

6.3 Surfaces of revolution

271

▸▸▸ When geometers take a walk in nature . . . . . . it is inevitable that they are attracted to the shapes of blossoms (Fig. 6.70, Fig. 6.71, and Fig. 6.72 on the left). Also inevitable are associations that come to mind concerning surfaces in technology (Fig. 6.70).

Fig. 6.70 Contour of a surface of revolution in nature and in technology

Fig. 6.71 Blossom of a bluebell: The bordering lines are the intersection lines between a surface of revolution and cylinders of revolution (compare computer graphic in Fig. 6.72 on the right).

Fig. 6.72 Broken surface contours in nature (fire lily) and in computer graphics.

In the early 1980s, the author was inspired by bluebells and consequently created one of his first computer drawings (Fig. 6.72 on the right). The problem at that time was that only raster graphics were available. This forced the programmer to develop several algorithms, e.g. a hidden surface algorithm and an algorithm for the detection of contours ([3]). ◂◂◂

272

Prototypes

The torus is a frequent building block of higher degree A sphere is constructed by rotating a circle about an arbitrary diameter. If the axis of rotation is translated within the circle plane into an arbitrary position, then a much more complicated surface is produced by subsequent rotation. It is called a torus and it is, as can be calculated, an algebraic surface of degree four. Geometrically speaking, it can be reasoned that a pair of circles lies in each meridian plane (Fig. 6.73) and is intersected by an arbitrary straight line in no more than four points.

Fig. 6.73 The torus as a surface of revolution: A circle rotates about a straight line in its plane.

The same surface is also enveloped if a sphere for which the circle in the meridian plane is a great circle rotates. It is, thus, possible to “roll around” a sphere inside a torus – this has many implications for practice.

Fig. 6.74 Torus as an envelope of spheres

6.3 Surfaces of revolution

273

A torus is a degree-four surface of revolution that is created by the rotation of a sphere or a circle about an axis located in its plane which does not contain the center. The outer ring of a torus is composed of elliptic points and the inner ring of hyperbolic points. The circles, on which the torus can be placed in a plane, carry parabolic points. Each circle of this kind is entirely contained in the tangent plane of each such point.

Fig. 6.75 Torus chains: Each link is made of half-ring surfaces which are joined cylindrically by cylinders.

A standard steel chain (Fig. 6.75) is composed of links made of two half-ring surfaces connected by cylinders of revolution. The radius of the circle which generates the torus is slightly smaller than the radius of the inner equator circle.

Fig. 6.76 Torus part and affinely distorted tori

Rotating only parts of the generating circle (meridian circle) produces open surfaces of revolution which are, geometrically speaking, still labeled as tori. The same is true if the rotation is applied to the whole circle but does not reach 360○ (Fig. 6.76 on the left). Fig. 6.77 shows the interior view of a torus – a challenge to the light sensitivity of the photo film and to the nerves of the “participants.” Fig. 6.78 shows two surfaces which are closely related to the torus. Put more precisely: The left surface is a half-torus, or it is bounded by surface parts

274

Prototypes

Fig. 6.77 A light at the end of the torus-shaped tunnel

Fig. 6.78 One of the two surfaces is not a torus.

which belong to a half-torus. The right surface is constructed in a way that resembles a torus but the meridian circle grows continuously smaller. Thus, this surface is no longer a surface of revolution.

Fig. 6.79 Other variants . . .

Fig. 6.79 shows further variations. The left image is a computer graphic. If a doubly curved torus was to be modeled using a paper strip, it would only result in an approximation because the surface thus generated is only single curved. The model on the right dates back to M.C. Escher and is often called an “Escher torus,” even though this is not quite correct.

6.3 Surfaces of revolution

275

Non-trivial sections of the torus

Fig. 6.80 Intersections of a torus with planes parallel to the axis

Algebraically speaking, the torus is a degree-four surface. Therefore, each planar intersection curve is, generally speaking, a degree-four curve. Among these are the so-called Cassini ovals, which are produced if the plane that intersects the torus is parallel to the axis of the torus. These curves have already caught our attention (Fig. 1.33, Fig. 6.80 on the right). If the intersection plane includes the axis, then the curve splits off into two circles. ⊕ Remark : There exist two other positions of the intersection plane where the intersection curve splits off into two circles: Each plane orthogonal to the axis intersects along two concentric circles. These two circles coincide if the plane (orthogonal to the axis) touches the torus. ⊕

Fig. 6.81 Villarceau circles in theory, as a wooden model, and in art (Benno Artmann)

⊕ Remark : There even exists a non-trivial case where the section curve splits off into two circles: The plane has to touch a pair of axis-symmetric meridian circles in hyperbolic surface points. We now have the case that two surfaces (the torus and the plane) share a degree-four curve, which – due to double contact – has to possess two double points. However, this is only possible if the intersection curve degenerates. In this case, the curve would have to split off into two circles, but in the case of a different degree-four surface, they might be arbitrary conic sections. Both conic sections are envelopes of the family of circles that is cut out from the torus-generating spheres (Fig. 6.82). The envelopes are circular (i.e., they are pass-

276

Prototypes

Fig. 6.82 Villarceau circles as envelopes

ing through the absolute points of the intersecting plane – see p. 194). This remarkable discovery goes back to the French geometrician Villarceau. ⊕

Fig. 6.83 Rhumb line on ring surfaces

⊕ Remark : Villarceau made even more discoveries: The circles named after him intersect all meridian circles – and thus all parallel circles – at the same angle. Such a curve is called a surface’s rhumb line or loxodrome.

Fig. 6.84 Sphere rhumb lines (loxodromes) with different course angles

The course angle of this rhumb line is, of course, extremely special. If the angle is changed even slightly, the curve no longer stays in a plane. In most cases, it does not even remain a closed curve but will wind around the torus “for all infinity” without ever returning to the starting point. For special angles, however, these

6.3 Surfaces of revolution

277

curves are closed (Fig. 6.83), and they are also algebraic, which means that they can be described by algebraic equations. The sphere, if you like, is also a special torus where the spine circle is shrunk to a single point. Interestingly enough, rhumb lines on spheres are never algebraic (except for course angles 0○ and 90○ ). Sphere rhumb lines are spiral-shaped curves that wrap around the poles. A ship traveling at a constant course angle relative to the north direction travels along such a rhumb line! This is actually a productive strategy in tropical regions for traveling from A to B without great navigational effort. Upon reaching polar regions, however, the captain would have to change his strategy. ⊕

Fig. 6.85 Closed rhumb lines on a ring torus (compare Fig. 6.107), among them a Villarceau circle.

Fig. 6.86 Very special triangulation of the surface of a torus with the help of rhumb lines (in the left image with Villarceau circles.) In each knot, the angles of the intersection angles are the same.

278

Prototypes

6.4 The torus as a prototype for all other surfaces of revolution The importance of the torus in geometry results, among other things, from the fact that each surface of revolution can be approximated by a sequence of torus segments. This directly follows from the insight that each planar curve can be approximated by a sequence of osculating circles. (Curves that are produced by chaining circles are called basket handle arches.) It can, thus, be said that: From a local perspective, each arbitrary surface of revolution is curved like its “osculating torus”. Some surfaces of revolution found in architecture are parts of a torus even if this is not immediately visible. The dome of the Mosque of Ibn Tulun in Cairo (built in the 8th century AD) is part of a so-called spindle torus because the meridian circle intersects the axis of rotation (Fig. 6.87 on the left, Fig. 6.88).

Fig. 6.87 Spindle torus in architecture and nature

The inner parts of a torus are often found in nature (Fig. 6.87 on the right), though we have to be generous in this assessment and speak only of the “basic form.” Seen this way, even the pressurized stream of water escaping from a valve in Fig. 6.89 could be likened to a spindle torus in its incipient phase. ▸▸▸ Contact lenses and astigmatism Wearers of contact lenses (or glasses) often hear the words “spherical” or “toric” from their ophthalmologist or optician. The surfaces of spherical lenses (spectacle lenses) are simply sphere caps with a slightly different radius. This causes the focal point of the lens system to be offset (when “focused

6.4 The torus as a prototype for all other surfaces of revolution

279

Fig. 6.88 Spindle torus as an ornament on an ancient wall

Fig. 6.89 A stream of water escaping from a valve

on infinity”, the focal point should lie precisely on the retina). This does not matter in spherical lenses, which are attached to the eye by adhesion: The sphere has the same curvature regardless of its tangential direction. Not only is the exact working of the eye’s optical system relatively complex, it is also different from what most people believe it to be. The actual refraction happens on the cornea while the lens inside the eye is only responsible for fine tuning. More information can be found on page 409.

Fig. 6.90 Contact lenses

The issue is further complicated if one additionally suffers from astigmatism. In such cases, the principal curvatures of the cornea – and sometimes also of the lens inside the eye – are different. This causes points on the retina to be

280

Prototypes

rendered in a “rod-like” manner. The corrective lens then has surfaces in the form of torus caps. On top of that, the axis of the torus can be twisted to varying degrees. As a result, toric lenses exist in a great variety of shapes, while the number of spherical lenses on offer (at granularities of quarterdiopters) is relatively limited and usually available in their full range in any optician’s store. Hard spherical contact lenses are often capable of correcting astigmatism by the mere fact that they allow smaller cavities between the lens and the eye to be filled with lacrimal fluid, which possesses nearly the same refractive index as the cornea itself. The liquid, thus, complements the cornea into a sphere (Fig. 6.90 on the left). Soft lenses, on the other hand, adapt to the ◂◂◂ toric shape of the cornea.

Cusps of contours Torus parts – and by extension, many surfaces of revolution – tend to develop contour cusps during projection. Fig. 6.91 shows different perspectives – most of them exhibit such cusps. During a normal projection orthogonal to the axis, the contour degenerates into two circles and into the lowest and uppermost circle that appear as one segment (Fig. 6.91 top left, also to some extent the picture of the anemone 6.92). Equator circles form the contour in axis direction (Fig. 6.91 on the right).

Fig. 6.91 Cusps of the contour of a torus

Fig. 6.92 Quarter-torus on an anemone

Fig. 6.93 How contour cusps are formed: In each point K of the contour line k, the associated tangent plane τ passes through the center Z. A cusp S occurs when the tangent s of the contour k passes through Z.

6.4 The torus as a prototype for all other surfaces of revolution

281

The respective contour in space is an arbitrary space curve k (composed of two branches, as can be seen in Fig. 6.93) that does not have any cusps. In each point K of k, the associated tangent plane τ – spanned by the tangent t of k and the respective projection ray – passes through the center of projection.

Fig. 6.94 Left: The contour of a torus in central projection (consisting of two curves k1 and k2 ) has four cusps in the projection. Right: Viewed from another projection center, k1 and k2 appear as space curves without cusps.

The probability that a tangent of k passes directly through the center Z of the projection at some point S is greater than one might expect. In those specific cases, the curve appears, locally speaking, as a point, and its orthogonal view possesses a cusp. The contour lines k in Fig. 6.93 and Fig. 6.94 are “jagged” in some parts, which results from the fact that the torus is triangulated. This causes the contour edges of the approximate polyhedron to become visible. In the projection from Z, these jagged edges cannot be seen.

Fig. 6.95 Contour of a torus, hyperboloid, and catenoid: Cusps on the contour never occur with hyperboloids but they do occur very often with the interior parts of tori.

Fig. 6.95 illustrates how the normal views of three visually similar surfaces of revolution may or may not have cusps despite the fact that the direction of the projection is the same. The catenoid is formed by the rotation of a catenary. The contour of a hyperboloid is always a hyperbola (Fig. 6.95 center), which is why cusps on the contour never occur with this type of surface.

282

Prototypes

Fig. 6.96 Coop Himmelb(l)au: Archaeological Museum Egypt in Cairo

⊕ Remark : The question of which surface is shown in Fig. 6.96 can thus be approached from this point of view. It is actually a hyperboloid which changes its shape into a torus towards the roof. Fig. 6.97 shows the cusps on the contour of general surfaces of revolution. The meridian is easily discernible on the right – no cusps occur there. A cusp is visible in the other two pictures (see also the appendix about freehand drawing). ⊕

Fig. 6.97 Cusps on the contour of surfaces of revolution (left and center)

Intersection of surfaces of revolution The flower petals of the bellflower in Fig. 6.97 form boundary curves which, when projected in axis direction, resemble circular arcs with great accuracy. The boundary curves of the petals can, thus, be said to emerge as the intersection curves of the surface of revolution with cylinders of revolution. This choice of phrase is in no way exaggerated: A designer at a computer is easily and quickly capable of modeling the curve in this way! In mechanical engineering, intersection curves of surfaces of revolution happen particularly frequently. The axes of these surfaces often intersect, and for this special case, Gaspard Monge has already specified a quick and efficient procedure.

6.4 The torus as a prototype for all other surfaces of revolution

283

Fig. 6.98 Principle: Variation of Monge’s auxiliary sphere . . .

If an auxiliary sphere is put around the intersection of the axes, it will intersect both surfaces along circles. The points of the intersection curve of both surfaces of revolution are then the section points of the circles (Fig. 6.98).

Fig. 6.99 . . . during normal projection on the connecting plane of the axes

If the surfaces are projected orthogonally to the plane spanned by both axes of rotation, then any common circles with Monge’s auxiliary sphere appear as line segments. However, this immediately provides their section points. If the size of the auxiliary sphere is now varied, an arbitrary number of points of the intersection can be found. ⊕ Remark : A note for advanced readers: Even if the circles on Monge’s auxiliary sphere no longer intersect in real space, they still share complex conjugate intersection points. The real straight line connecting these points remains the straight intersection of both carrier planes of the circles on the sphere. It can be shown that the normal projection of the intersection curve, if “extended”, passes through the orthogonal view of each such straight intersection. These points are called “parasitic points.” ⊕

Reverse engineering Let us, once again, consider the bellflower from before: The difficulty seems to lie in finding the surface parts of seemingly arbitrary surfaces that belong to a known surface class, such as the surfaces of revolution. In computer geometry, the term for this procedure is reverse engineering. Special programs are capable of analyzing objects digitized by 3D scanners and try to subdivide

284

Prototypes

them into parts which are, for instance, surfaces of revolution or developable surfaces.

Fig. 6.100 Surface of revolution (an ellipsoid of revolution in its upper part)

This can be greatly advantageous in practice. Consider a brilliant architectural model with many curved surfaces. Once this project is due to be put into practice, the construction costs can be greatly reduced if the surfaces involved can be reduced to certain standard surfaces without substantial changes to the design.

Fig. 6.101 Interior of the surface of revolution above (part of an affinely distorted torus)

Fig. 6.100 shows the limestone shell of a sea urchin – a general surface of revolution. Upon closer inspection, the entire upper part appears as an ellipsoid of revolution – an assumption that is further supported by its shadow. The lower part appears to be an affinely distorted torus, which, after a mere glance at Fig. 6.101, may not be immediately obvious to the layman. With some practice, it is possible to recognize planar intersections of a torus in Fig. 6.102 on the left and torus-shaped grooves on the right. Reverse engineering attempts to develop methods enabling computers, which are “stupid but fast,” to detect and prove circumstances which might not be easily seen with the naked eye. Much geometric theory is applied for this purpose:

6.4 The torus as a prototype for all other surfaces of revolution

285

Fig. 6.102 Planar torus intersections and torus-shaped grooves in a half-sphere

▸▸▸ Gauss map Points on a general surface can be associated with points on a sphere. We translate the associated surface normal to the center of the unit sphere and intersect it with the sphere. In general, the associated points will be distributed over the entire surface of the unit sphere.

Fig. 6.103 Spherical tangent, normal, and binormal image of the oloid

If the initial surface is developable, it will be touched along each generator by one and the same tangent plane with a fixed normal direction. The Gaussian image of a curve on the sphere equals the spherical binormal image of the surface’s edge of regression. Fig. 6.103 shows the spherical normal image of an oloid (blue). The curve could be called a “tennis ball curve.” It divides the sphere into two congruent halves and possesses a congruent top and front view in relation to its symmetry plane. If all surface generators are translated through the sphere midpoint, we get the spherical generator image. In the case of the oloid, this happens to be a curve with four cusps (in red), which also possesses a high degree of symmetry. This curve is the spherical tangent image of the surface’s edge of regression.

286

Prototypes

Finally, the spherical primary normal image of the curve of regression (which appears in green) may be considered. ◂◂◂ ▸▸▸ Automatic detection of developables The spherical image of a surface is not only interesting from a theoretical perspective; it is also utilized during reverse engineering: In order to detect whether or not a surface is developable, it can be scanned using a 3D scanner. This results in a “poiint cloud,” which exhibits “noise” due to measuring inaccuracy. The cloud’s surface normal is now interpolated and translated through the center of the test sphere. The more accurate this spherical image approximates the surface in the neighborhood of the curve, the more likely it is that the surface is developable.

Fig. 6.104 Reconstruction of a snail shell according to Boris Odehnal et al: The shape is essentially a spiral surface (see the next chapter), which can be “idealized” by a great number of measured points. If one compares the perfect shape to the real object, one notices that the snail changes its building strategy in the last phase.

This makes it very easy for the computer to detect general cylinders: Their spherical normal image is a great-circle of the sphere whose axis direction is the generator direction of the cylinder. The spherical normal image of a cylinder of revolution is a small-circle of the test sphere. ◂◂◂

6.5 Pipe and channel surfaces

287

6.5 Pipe and channel surfaces How to invent a new class of surfaces . . . A remarkable surface appears when a torus is inverted in a sphere (Fig. 6.105).

Fig. 6.105 Inversion of a torus in a sphere

The inversion in space preserves circles and angles like the planar version. The emerging surface, called the Dupin cyclide, was examined by the French geometer Charles Dupin and inherits a multitude of beautiful properties from the torus. Algebraically speaking, it is also – quite remarkably – of degree four.

Fig. 6.106 Dupin cyclide (Ring cyclide)

Dupin cyclides such as the torus possess two planes that touch the surface along two entire circles and carry two families of circles which correspond to the circles of latitude and the meridian circles. Furthermore, in the case of tori, two Villarceau circles lie in a double tangent plane. During inversion, this plane transforms into a sphere. For their part, the Villarceau circles pass over into circles on the cyclide which have to lie on this sphere and are, therefore, no longer coplanar (E. Hartmann). Of course, such surfaces are no longer surfaces of revolution. Nevertheless, they share some properties with them. This is due to the fact that they can

288

Prototypes

Fig. 6.107 Closed rhumb lines on a Dupin cyclide: the images were obtained by inversion of the closed rhumb lines on a torus (Fig. 6.85).

be generated in two ways as envelopes of spheres with constantly varying radii. With surfaces of revolution, the spheres are centered on the axis of rotation (Fig. 6.108), and with Dupin cyclides, they are centered on the spine ellipse and spine hyperbola, or on both spine parabolas. Surfaces enveloped by spheres with varying radii are called channel surfaces. Tori, in particular, can also be generated by spheres with a fixed radius. Such surfaces are called pipe surfaces. Of course, every pipe surface is automatically a channel surface. Thus, the torus is a channel surface in two different ways: firstly, as a surface of revolution (spheres centered on the axis), and secondly, as a pipe surface (spheres centered on the spine circle). We can immediately deduce why the spine curves of a Dupin cyclide are conic sections: An ellipse or hyperbola is the locus of the centers of all circles that touch two given circles (see page 188). It is thus possible to define each Dupin cyclide as the envelope of spheres in two ways: The centers of the spheres lie in a plane; in it, the spheres touch two circles. If we allow the given circles to mutually touch or intersect in this situation, three types can be differentiated: the ring-shaped (Fig. 6.106), the “singlehorn”, and the “double-horn” type (Fig. 6.110).

6.5 Pipe and channel surfaces

289

Fig. 6.108 Each surface of revolution is, in a trivial way, also a channel surface (see also Fig. 6.67).

Fig. 6.109 Dupin cyclides as envelopes of a family of spheres whose equator circles touch two given circles in a plane.

Pipe surfaces and blending surfaces Pipe surfaces are created by the motion of a sphere along a spine curve. Fig. 6.112 left shows in what way such surfaces depend on the form of the spine curve and the radius of the moved sphere. Two closely adjacent positions of the sphere share a circle – it lies in the radical plane of the two corresponding sphere centers. If we let both sphere positions move together, the straight line connecting the centers becomes the tangent of the spine curve, and the circle becomes a great circle of the sphere.

Fig. 6.110 Dupin cyclides (“single-horn” and two “double-horns”)

290

Prototypes

Fig. 6.111 Michael Schrott has strung together parts of such double-horns into a chain (Fig. 6.111) which is located inside a torus.

Fig. 6.112 The pipe surface as the envelope of a moved sphere (left). Pipe surfaces and art: Soundscapes by Bernhard Leitner

Fig. 6.113 A helical pipe surface

6.5 Pipe and channel surfaces

291

If a circle is moved along a curve in such a way that its axis is the tangent of the curve, it sweeps the same pipe surface as the family of concentric spheres centered at the spine curve. Pipe surfaces are often found in nature as well as in technology. They can be rendered flexible by keeping the radius of the generating circle small. ⊕ Remark : Fig. 6.112 (to the right) shows an organically conducted tube through which sound is directed. Openings that serve as sound sources were made in 40 places. Depending on the programming, curvatures are emphasized, counter-punctually combined, or transformed into fugue-like sequences. ⊕

▸▸▸ Blending surfaces Pipe surfaces are well-suited for filleting (blending) planar or cylindrical side surfaces against a plane: A sphere of given diameter should be rolled along the plane so that it touches the work piece. The remaining part of the sphere’s envelope is the sought-after blending surface.

Fig. 6.114 Blending surfaces in theory and practice

Fig. 6.114 shows the case that is by far the most common: A blend of two planes forms part of a cylinder of revolution, whereas a blend of a cylinder of revolution and a plane consists of parts of ring tori. In the right image, a number of tori are glued together. In the case of the anemone in Fig. 6.92, the shaft shaped like a cylinder of revolution transforms into a quarter-torus – just as it would during a classical blending.

Fig. 6.115 Blending surfaces in architecture: BMW world, Munich (Coop Himmel(b)lau)

292

Prototypes

In mechanical engineering, such blendings are important for increased stability but are sometimes also employed in order to avoid sharp edges (Fig. 4.78) or simply for design purposes. Even “in the grand style”, blending surfaces (Fig. 6.96, Fig. 6.115) are required to make the dreams of architects become reality.

Fig. 6.116 Blending surfaces in architecture: Niterói Contemporary Art Museum, Brasilia (Oscar Niemeyer). The blending surface consists of two different torus sections connected by a cone of revolution.

◂◂◂

▸▸▸ The altitudes of a tetrahedron lead to an aesthetic lamp

Fig. 6.117 The axes of the four cylinders of revolution are altitudes of a regular tetrahedron. The blendings are comparatively complicated.

The lamp in Fig. 6.117 reveals a lot of geometric insight on the part of its designer: Four cylinders of revolution with equal diameters and intersecting axes are arranged in a well-balanced way. This requires the cylinders to have the altitudes of a regular tetrahedron (Fig. 6.117, middle). Therefore, the intersections without blending consist of six partial ellipses in their respective symmetry planes. When we try to blend the cylinders, we have to guide a sphere along a curve in the symmetry plane in such a way that it touches those ellipses. Thus, the path of the sphere’s center consists of parallel curves of ellipses. ◂◂◂

7

Further remarkable classes of surfaces

In the ideal case, surfaces can be defined by motion. Surfaces of revolution are produced by a rotation of a curve about an axis. In the case of helical surfaces, the generators additionally experience a translation along the axis of rotation. Surfaces of translation are generated by the translation of a curve along another curve. Ruled surfaces are generated by straight lines moving along arbitrary curves. Different surfaces (such as spiral surfaces) can be generated by moving space curves along other such curves and by changing the former according to certain rules. All noted classes of surfaces play significant roles in nature and technology. Helical surfaces, for instance, may be employed in order to “transform” rotation into translation, which makes them useful as propeller surfaces or drills. Several types of spirals can be found in nature, for example, in snail shells, animal horns, or even in the shapes of galaxies in outer space. Translation surfaces are particularly noteworthy. They can also be interpreted as midsurfaces of space curves. A special difficulty arises when a surface cannot be put into any of these categories. Minimal surfaces, for instance, are defined by a very characteristic curvature property and play a great role in physics, architecture, and nature. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_7

293

294

Further remarkable classes of surfaces

7.1 Ruled surfaces Next to surfaces of revolution, ruled surfaces are particularly significant. Ruled surfaces are generated by a moving straight line, and despite carrying only straight lines, they are not developable in the general case.

Fig. 7.1 Motion of a straight line

Fig. 7.1 illustrates this situation: A straight line is moved through space and generates a surface which is, generally speaking, doubly curved (this is immediately evident from the curved contours). Let us begin with the developable exceptions: cylinders are formed by the motion of a straight line which is parallel to a fixed direction during the entire motion, and they are ruled surfaces by definition. They are developable, and therefore, their contours consist only of straight lines. Cones are developable ruled surfaces, too: They are generated by moving a straight line through a fixed apex in an arbitrary way.

Fig. 7.2 Tangent surface of a space curve. A different section of the same surface (right); the edge of regression proceeds on an ellipsoid, and its top view is a “nephroid (left).”

Finally, developables – the most general single curved surfaces – are also ruled surfaces because they are swept by the tangents of a space curve. The

7.1 Ruled surfaces

295

associated motion of the straight line can, without proof, be interpreted as follows: A developable may be created by following a point K along a director k and considering the straight line as the tangent of k. In such cases, the director is called the curve of regression or edge of regression, because it can be shown that along its trajectory, the generated tangent surface possesses a sharp ridge (Fig. 7.2). Thus, we can say: All developable surfaces (cylinders, cones, and developables) are ruled surfaces. Now, let us move on to general ruled surfaces, whose shapes permit many (though not quite arbitrary) variations. In each case, an arbitrary tangential section through a surface point P will retain the direction of the generator which passes through it. Therefore, we can say: All non-developable ruled surfaces are hyperbolically curved and, thus, constantly “saddle-shaped”.

Conoids

Fig. 7.3 Conoidal ruled surfaces as the shapes of roofs (circle conoid)

So-called conoids represent an interesting category of non-developable ruled surfaces. The motion of their generating straight line is defined in such a way that the straight line always intersects a straight director and another arbitrary given curve. As an additional condition, the surface must possess a directing plane which is parallel to all generators. Fig. 7.3 shows a circle conoid where the director is a half-circle. Fig. 7.4 shows a conoidal roof shape, which is basically defined in such a way that a horizontal director is connected to a wave-shaped curve by straight lines which appear parallel in a top view (compare also Fig. 7.7). The question is whether or not the resulting ruled surface is developable, which would imply advantages for its practical construction.

296

Further remarkable classes of surfaces

Fig. 7.4 Arbitrary conoidal ruled surfaces as roof shapes: Pictured on the right is a model by Antoni Gaudí for practical construction.

This question cannot be answered merely by evaluating the visual image, since the recognizable contours are too short to discern any curvature. On the other hand, it is theoretically possible to negate the question outright, considering the following: A ruled surface that contains a straight transversal of all generators is not developable. A conoid, in particular, is not developable. If P is a point on the director, then the tangential section in P is composed of the generating straight line and the director. Thus, the point is hyperbolic.

Fig. 7.5 Conoidal ruled surfaces used in design (Santiago Calatrava).

Fig. 7.5 shows a similar problem. It again concerns two conoids with a horizontal director which share a space curve (from a certain perspective, it appears as a parabola, as in Fig. 7.5 on the left). Due to a twisting of the surface, a slight curvature in the contours can be recognized, from which it can be deduced that the surfaces are “almost” but not “wholly” developable. In practice, this means that a slightly ductile surface – such as the fabric of an elastic tent – should be able to cope with the curvature. Let us examine this example further: Both surfaces in Fig. 7.5 can be “animated” as in Fig. 7.6. Proceeding from a parabola, which determines the length of the rods in the initial surface, the lower “crossbar is raised to a

297

7.1 Ruled surfaces

Fig. 7.6 . . . or as a fancy sliding gate

Fig. 7.7 Model of a conoidal surface

higher level”. Appropriate hinges, which prevent the rods from tilting sideways, have to be placed at the buckling spots.

Two important and two beautiful applications There exist two conoids which are known under a special name in academic literature.

Fig. 7.8 The hyperbolic paraboloid is a conoid, a translation surface, and a surface of degree two.

The hyperbolic paraboloid (Fig. 7.8) is a particularly important conoid, and its second director is also a straight line. From this it follows that, as we have already seen, the surface possesses an infinite number of directors. Any two straight lines from one family together with any two straight lines from the other family form a skew generator quadrangle. From a special perspec-

298

Further remarkable classes of surfaces

tive, both pencils of generators appear as pencils of parallels; otherwise, the contour is always a parabola.

Fig. 7.9 Each ruled surface is touched by an hyperbolic paraboloid along a whole straight line.

Hyperbolic paraboloids are not just extremely interesting surfaces. They are also very practical, because locally, they can be considered as the prototype for any arbitrary ruled surface. Fig. 7.9 illustrates how a ruled surface is touched by an HP shell along a whole straight line.

Fig. 7.10 Degree three conoid with a parabola as a director

A very visually appealing surface can be created by defining the director as a parabola. ⊕ Remark : Such a surface is of degree three, and its prototype can be given by the simple equation z = x2 y. The prototype of an hyperbolic paraboloid can be given by the almost identical equation z = xy. Furthermore, arbitrary affine mappings can be applied to these prototypes. Due to the fact that affine mappings preserve parallelism, the surfaces stay conoidal, and their degree likewise remains unaffected. ⊕

Besides the HP shell, the right helicoid is also of great significance. It is created by rotating a generator about an orthogonally intersecting axis and translating it in proportion to the angle of rotation along this axis. The axis is the director, and all generators are parallel to the axis’ normal plane. Each path curve of a point on the generator could serve as the second director.

299

7.1 Ruled surfaces

Fig. 7.11 Tangential intersection of degree-two and degree-three surfaces

Fig. 7.12 The right helicoid is a conoid and a helical surface. Left image: normal projection, winding to the left. Right image: central projection, winding to the right.

These path curves are helices. The right helicoid can also be categorized as a helical surface, which we shall examine more closely in a separate chapter. ⊕ Remark : The right helicoid does not possess a “degree” in the algebraic sense – rather, it is called transcendental. It is, therefore, impossible to correlate the coordinates x, y, and z of its points in an algebraic relationship. However, it is possible to formulate a parameter representation or implicit representation as follows: x = v ⋅ cos u, y = v ⋅ sin u, z = c ⋅ u

(u ∈ R, v ∈ R) ⇒

z x = tan , y c

where u is the angle of rotation about the z-axis and v denotes the distance from this axis. Depending on the choice of parameter intervals, we get different parts of the surface. ⊕

Our fourth and last conoidal example is Plücker’s conoid. It can be generated in a similar way as the right helicoid, the only difference being that the

300

Further remarkable classes of surfaces

Fig. 7.13 Plücker’s conoid

translatory motion of the generator in the direction of the director proceeds not proportionally to the angle of rotation but to its sine. This produces the straight line’s harmonic oscillation. The path curves of generator points are oscillation curves. Despite its similarity to the right helicoid, Plücker’s conoid is remarkably algebraic – of degree three, to be precise. This means that each test straight line yields three exactly calculable intersection points, two of which may be complex conjugate. ⊕ Remark : Due to its generation, Plücker ’s conoid possesses the parameter representation x = v ⋅ cos u, y = v ⋅ sin u, z = c ⋅ sin 2u (u ∈ R, v ∈ R).

It is now possible to eliminate the parameters due to sin 2u = 2 sin u ⋅ cos u and sin2 u + cos2 u = 1, which results in the following implicit equation of the surface: 2c ⋅ x ⋅ y = (x2 + y 2 ) ⋅ z. From this, it can be seen that Plücker’s conoid is of degree three. ⊕

Fig. 7.14 Ruled surfaces during the construction of bridges

Architecture often employs “wireframe models” of ruled surfaces. Fig. 7.14 shows a pedestrian bridge by Calatrava in Bilbao. ▸▸▸ A spatial version of the theorem of the angle of circumference According to the theorem of the angle of circumference (p. 9), a straight line segment EF in 2-space is seen at a constant angle α from any point of a

7.1 Ruled surfaces

301

pair of circular arcs passing through E and F . For α = 90○ , the pair of circles becomes one circle (the Thales circle) with diameter EF .

Fig. 7.15 Two simple generalizations of the theorem of the angle of circumference.

By looking for all points in 3-space that see a straight line segment EF under a constant angle α, the locus is a torus, obtained by rotation of the situation in 2-space about the axis EF (Fig. 7.15, left). Another possible generalization could look for all points P with ∢(P e, P f ) = α, where e and f are given lines in space. When e and f are parallel, the locus is a pair of cylinders of revolution (Fig. 7.15, right).

Fig. 7.16 Non-trivial spatial version of the theorem of the angle of circumference. Left α ≠ 90○ , right α = 90○ .

If e and f are skew, then things become more complicated: The result is a ruled surface of degree four in the general case α ≠ 90○ . For α = 90○ , the surface degenerates to an elliptic hyperboloid. The proof can be found in [17]. ◂◂◂

302

Further remarkable classes of surfaces

7.2 Helical surfaces The fascination behind the helix In planar geometry, there exists exactly one curve that is invariant under an infinite number of reflections and rotations – the circle. This undoubtedly accounts in no small part for the circle’s beauty as well as its practical applicability. In space, there exists a class of curves that may allow self-motions – the helices. A helical motion is defined as the combination of a rotation about a fixed axis and a simultaneous proportional translation along this axis. The pitch belongs to a full revolution as the distance of translation.

Fig. 7.17 Helices with an “accompanying tripod”

Helices are the path curves of points undergoing a helical motion. During a helical motion, they are continuously translated and screwed into each other. Additionally, they are invariant under an infinite number of point reflections as long as the center lies on the axis, and translations in the direction of the axis if the distance of translation is an integer multiple of the pitch. The factor of proportion is called the screw parameter and is henceforth denoted by p. If a point is rotated by an angle ϕ about the screw axis, then it is simultaneously translated by an offset p ⋅ ϕ along this axis. If h is the h . pitch, then p = 2π If the screw parameter is positive, one speaks of a right helical motion. If it is negative, we speak of a left helical motion. The case p = 0 is special and yields a pure rotation, whereas p = ∞ yields a pure translation.

⊕ Remark : The rotation and the associated translation need not necessarily be uniform, but what matters in any case is the proportionality. As a plant coils itself around a pole (Fig. 7.18), its speed of growth may vary, but the result is, neverthe-

7.2 Helical surfaces

303

less, the same. A mathematician would say that the helix need not be parametrized by time. ⊕

Fig. 7.18 Normal projections (orthogonal to the axis) of helices

The following properties can hardly be improved in terms of elegance: Helices always lie on cylinders of revolution about the screw axis a. They have constant slope with respect to a base plane π ⊥ a. In an orthogonal projection on π, a helix appears as a circle. In an orthogonal projection on a plane ν ⊥ π (ν ∥ a), a helix appears as a sine curve. The development of the carrier cylinder shows a straight line as the development of the helix. Proof : Neither a translation in the direction of the axis nor a rotation about the axis change the distance from the axis. Thus, helices lie on cylinders of revolution, which appear as circles in a normal projection in the direction of the axis. By definition, a helix intersects each generator of the carrier cylinder at the same angle. The ratio between the translation component and the rotation component is likewise constant – even if only an infinitesimal segment (the tangent t) of the curve is considered. The tangent is contained in the tangent plane τ of the cylinder, where the angles to the generator and the base plane π can be measured. This angle α = ∢tπ has the value tan α = p/r, where r denotes the distance of P to the screw axis. If t is projected orthogonally to a plane ν ⊥ π, then the translation component remains undistorted while the rotation component is shortened depending on the angle ψ = ∢τ ν by a factor of cos ψ. The projection curve is, thus, a cosine – and, therefore, also a sine. Both curves do not differ in their shape but are merely phaseshifted. Since the helix intersects all generators of the carrier cylinder at the same angle, the development also intersects the parallel straight developments of the cylinder’s generators at a constant angle and is, therefore, also a straight line. ⊕ Remark : Let us now use analytic methods in order to capture the path of a point P at a distance of r to the axis as a way of proving the above theorem. For this purpose, we shall adapt a Cartesian coordinate system to the situation as simply as possible: Let the axis be the z-axis and P (r, 0, 0) lie on the x-axis. After the rotation through ϕ and the simultaneous translation about p ⋅ ϕ, P has the coordinates x = r ⋅ cos ϕ, y = r ⋅ sin ϕ, z = p ⋅ ϕ.

The front view of the path curve can be represented by y = r⋅sin ϕ, z = p⋅ϕ, and it is, thus, a sine curve with the equation y = r ⋅ sin(z/p). Every other horizontal normal

304

Further remarkable classes of surfaces

projection with viewing angle α also yields a congruent (and merely phase-shifted) curve in a (u, z) coordinate system: u = x ⋅ cos α + y ⋅ sin α = r ⋅ cos ϕ ⋅ cos α + r ⋅ sin ϕ ⋅ sin α = r ⋅ cos(ϕ − α), z = p ⋅ ϕ. The development of the curve is given in a (v, z)-system by the linear equation v = r ⋅ ϕ, z = p ⋅ ϕ ⇒ z = p/r ⋅ v, which implies that the curve is a straight line. ⊕

⊙

Fig. 7.19 Helix with a shadow

Arbitrary orthogonal views of helices (Fig. 7.19) stand – as we shall soon discover – in an affine relation to so-called cycloids. Central views as in Fig. 7.19 on the right have an appropriately complicated shape and pose a challenge to freehand drawing.

Fig. 7.20 “Glowing” helix (LED lamp) with reflections in glass

305

7.2 Helical surfaces

When straight lines or circles undergo a helical motion . . . All path curves during a helical motion are helices, except the paths of points on the axis. What kind of surfaces are produced if, instead of points, we let other objects – such as straight lines – undergo the same motion?

Fig. 7.21 On the left: The right helicoid alone may help to overcome the tedium of this car park. Center: Right helicoid in the Sagrada Familia (Antoni Gaudí). On the right: Intercity Bank in Lima (Hans Hollein).

When discussing ruled surfaces, we have already touched upon an equally important helical surface – the right helicoid (Fig. 7.12). It is produced when a straight line which intersects the screw axis at a right angle undergoes a helical motion. Right helicoids are primarily found in technology. For instance, the smoothly cleaned wall on the underside as well as the path surface (upper) on the upwards-leading driving path the car park in Fig. 7.21 both belong to this class. Right helicoids are similarly employed for the surfaces of propellers or cooling fans.

Fig. 7.22 Ship’s propeller, Archimedean screw

306

Further remarkable classes of surfaces

With the help of helicoids, it is possible to induce propulsion by means of mere rotation – the screw motion is, thus, decomposed into its components of rotation and translation. Due to the inertia of the medium through which the motion should proceed (air or water), the surface “supports” itself on the medium and propels the airplane or ship forwards (or backwards, as in the case of ships’ propellers – see Fig. 7.22). Right helicoids can be employed to lift liquids – this property was already recognized and utilized by Archimedes (see Fig. 7.22 center and on the right).

Fig. 7.23 Impeller of a snow blower

Another interesting application of right helicoids can be found in so-called impellers (Fig. 7.23), which are, for instance, built into excavator shovels (and turned electrically) and snow shovels. By a mere rotation of the apparatus, the mixture of sand and cement in one direction by the left part of the left-handed screw and in the opposite direction by the right-handed screw. Variations exist with a continuous outer screw and a counter-rotating inner screw.

Fig. 7.24 Theoretical version of an impeller

Fig. 7.24 shows a “purely geometric” variation of a double screw, where the transition from one helix to the other proceeds “smoothly” (or differentiably).

307

7.2 Helical surfaces

▸▸▸ The DNA double helix The double helix is a popular symbol of molecular biology. Hereditary material is preserved in the form of deoxyribonucleic acid (DNA), which is made up of two strands (or a double helix) of molecules in the chromosomes of the cell nucleus. These DNA stands wrap themselves about an imagined axis – similarly to opposite helices on the right helicoid. More on this matter can be found in application p. 314. ◂◂◂

Fig. 7.25 Vises

The conversion of rotation into translation does not necessarily have to produce propulsion. All olive presses, vises, and corkscrews (Fig. 7.27, Fig. 7.31) take advantage of the same principle. On a miniature scale, the conversion of rotation into translation is done with all ordinary screws!

Fig. 7.26 Bolts and nuts

Fig. 7.27 Classic corkscrew

The following question arises: What kind of helical surfaces are employed in screw threads? They do not seem to be right helicoids – as, for instance,

308

Further remarkable classes of surfaces

those in vises. The surfaces are created by straight lines skew to the screw axis. Let us consider the matter from a geometric standpoint. In machine drawing, screws and bolts are displayed in a simplified manner (Fig. 7.28).

Fig. 7.28 Blind holes and clearance holes

Different types through different directions of the straight line

Fig. 7.29 Left-handed and right-handed straight ruled helical surfaces

If the generating straight line of the right helicoid is translated so that it no longer intersects the screw axis, so-called straight open ruled helical surfaces are obtained. Fig. 7.29 shows two such surfaces, where the left surface possesses a negative screw parameter and the surface at the center possesses a positive one. A helix with none-zero axis distance can be seen in the corresponding top view. The general case is given if the generating straight line is skew with respect to the screw axis. Both rightmost skew open ruled helical surfaces in Fig. 7.30 serve as illustrations. If the skew generator meets the screw axis, then we speak of an skew closed ruled helical surface. Skew ruled surfaces possess a self-intersection, which is naturally also a helix.

309

7.2 Helical surfaces

Fig. 7.30 Different skew ruled helical surfaces

Fig. 7.31 Another corkscrew (“in action”). One part of the surface is a ruled helical surface.

There exists only one type of developable helical surface None of the aforementioned ruled helical surfaces are developable in the general case, and this is recognizable from their curved contours. The surface in Fig. 7.30 on the right, however, seems to possess straight contour parts. It is, in fact, possible for an skew open ruled helical surface to be developable under a single condition: The generators have to be tangents of a helix g. The whole surface is then a tangent surface (developable) of g, and g is a

310

Further remarkable classes of surfaces

Fig. 7.32 Helical developable with a helix for its edge of regression

sharp ridge (curve of regression) on this developable. Fig. 7.32 shows another helical developable – in the right image, another part of the surface is visible (every ruled surface is, in principle, unbounded).

Fig. 7.33 A developable special case of a ruled helical surface (cylinder of revolution)

Fig. 7.33 illustrates one further exception for ruled helical surfaces: If the screwed straight line is parallel to the screw axis, a cylinder of revolution is created. Following this interpretation, a cylinder of revolution can be seen as a surface of revolution, a helical surface, and a translation surface.

Fig. 7.34 Cone wheels with efficient gear flanks

Helical developables are often used in engineering practice. They occur in mechanical engineering as gear flanks for so-called involute gears or mills (Fig. 7.35), which serve to transfer rotations onto skew axes. During road con-

311

7.2 Helical surfaces

Fig. 7.35 Mill flanks

Fig. 7.36 Highway entrance in theory . . .

struction, helical developables form the embankment for highway entrances (Fig. 7.36 and 7.37).

Fig. 7.37 . . . and practice (Euler spirals occur in top view)

Fig. 7.38 Masonry drillmasonry drill with helical developables as flanks

It is possible to apply screw motions to circles or spheres By screwing curves other than straight lines, complicated surfaces may be produced. The most common case that occurs in nature is the application of screw motion to a circle. Even by restricting oneself to these circular helical surfaces, it is possible to distinguish between several types that differ in the initial position of the circle. ⊕ Remark : Fig. 7.39, for instance, shows a nifty keychain, which approximates a circular helical surface. The twisted circle is the “profile” of the surface in a crosssection perpendicular to the screw axis. ⊕

By far the most frequent type of circular helical surface is the helical pipe surface.

312

Further remarkable classes of surfaces

Fig. 7.39 Special circular helical surface: The screwed circle is situated in a cross-section plane perpendicular to the screw axis, which can be deduced from its shadow. The colored circle sections form areas on the surface that are bounded by a helix.

A helical pipe surface is formed if a circle undergoes a helical motion such that its axis is tangent to the helix that is the path of the circle’s center. It can also be created as the envelope of a sphere, which counts the circle among the many possible great circles.

Fig. 7.40 Helical pipe surface in different normal projections

⊕ Remark : This assertion is easy to verify: The circle undergoes a motion which, by definition, is orthogonal to its plane. Thus, the surface is touched by a cylinder of revolution along the circle, and a sphere fits into this cylinder, which is in contact along the original circle. What makes this surface significant is the generation of the helical surface by means of a sphere. ⊕

Therefore, it is possible for a sphere to roll through the surface while touching the surface along a great circle in each moment. Many water slides in swimming pools are comprised of parts of helical pipe surfaces (Fig. 7.41 on the left). There is also another variation, where the circle in a meridian plane is twisted (visible in Fig. 7.41 at the center). The thus generated surface is called the meridian circular helical surface. ⊕ Remark :

7.2 Helical surfaces

313

Fig. 7.41 Helical pipe surface and meridian circular helical surface as slides

Fig. 7.42 Helical pipe surface, this time generated by the cross section

Fig. 7.40 shows different normal views of the helical pipe surface (on the left, the projection is perpendicular to the axis; on the right, we have a projection in the direction of the axis). It is clearly visible that the generating circle is not vertical. Instead, it has the respective tangent of the mid helix as its axis. The contours often exhibit cusps, depending on the radius of the twisted circle. Fig. 7.42 shows the same helical pipe surface but generated by a kidney-shaped cross-section instead of a circle. Points of this cross-section can be created by proceeding from the originally twisted circle and applying the helical motion to its points P until they “reach” a cross-section plane π that is normal to the axis. The height difference ∆z = P π corresponds to a proportional angle of rotation ϕ = c ⋅ ∆z. ⊕

Fig. 7.43 Steel cable (two helical pipe surfaces) under a small workload

314

Further remarkable classes of surfaces

Helical pipe surfaces are among the most frequently found surfaces in nature and technology. The “helices” in Fig. 7.18 and Fig. 7.19 should, strictly speaking, also be counted among them. ▸▸▸ The secret of DNA

Fig. 7.44 Deoxyribonucleic acid encodes hereditary information and passes it on to the following generation via germ cells. The strands may be visualized from a geometric standpoint by two interlocked helical pipe surfaces.

It would be presumptuous even to attempt to describe the manifold secrets of DNA at this point, but as for its geometry, this much can be said: As described in application p. 306, DNA molecules take the form of the famous double helix. Each strand represents a sequence of molecular building blocks (phosphoric acid, deoxyribose, and one of the four bases – adenine, guanine, cytosine, and thymine). The order of these bases determines the genetic code. ◂◂◂

Fig. 7.45 Left: a strange kind of “double helix”; right: helical stairs, looking downwards

7.3 Different types of spiral surfaces

315

7.3 Different types of spiral surfaces

Fig. 7.46 Helix, helispiral, and the “classical” spiral all (right-handed)

Helispiral motion

Fig. 7.47 A typical helispiral surface

An interesting variant of helical motion is often found in nature – the helispiral motion. While the regular helical motion leaves the diameters unaffected, helispiral motion makes them smaller or larger in linear proportion to the height. Fig. 7.46 juxtaposes the helical motion (left) with the helispiral motion (center). Fig. 7.48 pictures the surface that is created if this kind of transformation is applied to an equilateral triangle that intersects the axis orthogonally at its midpoint. The principle is as follows: Perform a rotation about the axis by an arbitrary angle ϕ while simultaneously changing the distance to the center by the

316

Further remarkable classes of surfaces

Fig. 7.48 Helispiral motion of a horizontal equilateral triangle (left-handed)

Fig. 7.49 Helispiral motion: Pieter Bruegel the Elder, The Tower of Babel

factor p ⋅ ϕ. The value p is called the parameter of the helispiral motion. Thus, the increase in distance is linear, as the double angle produces the double distance. A helispiral motion is given if the points in space are rotated about an axis and simultaneously scaled proportionally in relation to a fixed point on the axis. This is analogous to the following “growth recipe” of nature: “Grow larger from a center at a linear speed and simultaneously rotate about an axis through the center.” This principle seems to be applied in the growth of animal horns, plant sprouts, and even certain trees. Geometrically, this instruction indicates that, at every turn, all points change their distance to the axis by the same amount. An exceptional point exists on the axis – the origin of growth – from which all path curves (called helispirals) make their way. Their top views are Archimedean spirals. These planar curves are created by letting a point move at equal velocity on a constantly rotating rod. From a spatial perspective, a helispiral may also be created by letting a point move at equal velocity on a straight line, which, in turn, rotates about an non-perpendicularily intersecting axis. Another variation may be described as follows: If a point undergoing a helical motion is moved at equal velocity

7.3 Different types of spiral surfaces

317

Fig. 7.50 Variation of circular helispiral surfaces in theory . . .

Fig. 7.51 . . . and practice

on a normal to the screw axis, its path curve is a helispiral. During this type of motion, the point moves on a right helicoid.

The classical spiral motion In addition to helispiral motion, there exist numerous other types of spatial spiral motions which share the same principle that always involves rotating about an axis and a change of distance that is somehow depending on the angle of rotation. The ensuing planar spiral motion proceeds by complete analogy.

Fig. 7.52 Helispiral-shaped recess – design by Anita Aigner and Franz Lesák

318

Further remarkable classes of surfaces

Fig. 7.53 The tangent surface of a helispiral (on the left and right) and a fascinating parallel in nature (feather dust worm, Dalmatia).

Fig. 7.54 This spiral is “merely” a central projection of a helix.

Fig. 7.55 In this corkscrew, the helical pipe surface transforms into a helispiral surface, which is no longer a pipe surface but a channel surface (S. 287).

The classical (so-called cylindro-conical ) spiral motion works as follows: Perform a rotation about an axis by a very small angle ϕ and simultaneously increase the distance from the center by a value that is proportional to the size and rotation angle, which also equals a multiplication by (1 + p ⋅ ϕ). The value p is called the parameter of the spiral motion. This process could be compared to a “compound computation of interest”, as the “initial capital” increases with each rotation. Thus, the growth is exponential. If we allow for arbitrary rotation angles, we arrive at the following definition:

Fig. 7.56 Spiral right helicoid (on the left) and spiral developables

319

7.3 Different types of spiral surfaces

Fig. 7.57 Computer simulations of “real” shellfish and snail shells

A classical spiral motion is given if the points in space are rotated about an axis and simultaneously scaled from a fixed center on the axis in an exponential manner. This definition correlates with the following “growth recipe” in nature: “Expand by a certain percentage in relation to a center and simultaneously rotate in proportion to the percentage about an axis through this center.” This kind of growth can be observed in the calcite shells of snails and shellfish, which bear a remarkable resemblance to their computer simulations (Fig. 7.57). However, studies by Boris Odehnal have shown that specimens of these shells are often subject to irregularities (Fig. 6.104).

The contour of a spiral surface

P

Q Fig. 7.58 Left: The interior of a snail’s shell can be quite complicated. Right: the corresponding contour with cusps.

Fig. 7.58 shows the inner part of a shell. On the right, one can see that the contour starting at P is first “responsible” for the outer part and then changes to the “inner contour”. Fig. 7.59 shows a shell under three only slightly different viewing angles.

320

Further remarkable classes of surfaces

Fig. 7.59 A computer-generated shell under slightly different projection angles

Fig. 7.60 A living snail’s shell under slightly different projection angles, . . .

Fig. 7.61 . . . and its petrified ancestors.

The relation to the helix Let us once again juxtapose the generation of the three aforementioned path curves (helix, helispiral, classical spiral), assuming the most equal initial conditions.

7.3 Different types of spiral surfaces

321

Let a fixed axis a (e.g., the z-axis), a fixed angle of rotation ∆ϕ, and a fixed distance of translation ∆z (in axis direction) be given. Let P be an arbitrary point to which we shall repeatedly apply the following instructions: First, P is to be rotated through ∆ϕ about a and then translated along a by ∆z.

Fig. 7.62 Screw motion, helispiral motion, and classical spiral motion in a top view

This already yields the points of a helix. For a helispiral motion, P is additionally translated orthogonally to the axis direction by a distance proportional to the angle of rotation s = p ⋅ ∆ϕ, while for classical spiral motion, P is changed in relation to the origin by a factor depending linearly on the angle of rotation k = (1 + p ⋅ ∆ϕ). This, in turn, yields points on the helispiral and on the classical spiral. If the objective is to calculate n times as many points, then the n-th part of ∆z, ∆ϕ, and the translation distance s are to be considered. The scaling factor of the classical spiral is to be replaced by its n-th root. Helices and classical spirals are also slope lines (lines with a constant angle to the axis or to the base plane). They lie on cylinders with axis-parallel generators: In the case of helices, it is a cylinder of revolution. In the case of classical spirals, it is a logarithmic cylinder. Helispirals, however, are no slop lines.

322

Further remarkable classes of surfaces

7.4 Translation surfaces Translation surfaces as the loci of chord midpoints Remark: The proofs for the theorems shown in this section can be elegantly realized by means of vector calculus, and they can be found at www1.uni-ak. ac.at/geom/dld/canada-lines.pdf. If we connect all points P1 of an arbitrary curve c1 with all points P2 of another arbitrary line c2 , the locus of all midpoints M is a surface of translation. The surface contains two families of congruent curves. The prototypes c∗1 and c∗2 of these profile curves are similar to c1 and c2 (factor 1/2).

c2 P2

c∗2

c∗1

c1

M P1

Fig. 7.63 Given two lines c1 and c2 : We consider the locus of all midpoints of P1 ∈ c1 and P2 ∈ c2 .

Paraboloids as translation surfaces Apart from the trivial case where both profile curves are straight lines and the surface is thus a plane, Fig. 7.63 shows the famous, simplest, and nontrivial case: If c1 and c2 are parabolas with parallel axis direction and nonparallel carrier planes, the corresponding translation surface is a paraboloid (degree two). When one of the generating lines is straight, the result is a parabolic cylinder. Trivially, if both generating lines are straight, the translation surface is a plane. The above theorem holds for “genuine space curves” if c1 = c2 , which means that one single curve can already define a translation surface. Henceforth, we shall refer to such a surface as midsurface.

The helicoid as a translation surface Besides the classical example of a midsurface (the paraboloid), there is also the following non-trivial example:

323

7.4 Translation surfaces

The midsurface of a helix is a helicoid. Therefore, a helicoid is not only a helical surface but also a surface of translation.

P2

M c∗1

P1 c∗2

c1

c2 Fig. 7.64 If c1 = c2 is a helix, the midsurface is a helicoid which is, therefore, also a surface of translation with two non-trivial families of helices on it.

a

a Φ

Φ c∗1

c∗1

c∗2

c∗2

Fig. 7.65 Left: Two congruent non-trivial helices with arbitrarily chosen equal radius on a helicoid are displayed. Right: With an adequate change of the projection in the direction of a tangent of the green helix, the red helix becomes a contour line.

Since c1 = c2 , the prototypes c∗1 and c∗2 of the pencils of parameter lines are congruent. All parameter lines intersect the screw axis; they are not helical orbits of the screw motion that generates the helicoid. The generating helix c = c1 = c2 lies on the helicoid Φ that is thus uniquely defined. If we vary the radius r of c, this will generate the same surface. This

324

Further remarkable classes of surfaces

will result, once again, in two families of non-trivial helics on Φ with radius r 2 (Fig. 7.65). A helicoid (parameter p) carries a two-dimensional manifold of congruent helices (parameter p2 ). Their projections in the direction of the axis yields circles through the image of the axis. There is a well-known theorem about helicoids in relation to “non-trivial” helices:1 The contour of a helicoid for any parallel projection is a helix.

Other surfaces of revolution that are also translation surfaces The cylinder of revolution is a trivial example of surfaces of revolution that are at the same time translation surfaces. The paraboloid of revolution (Fig. 6.19 on the left) is less trivial – like all paraboloids, it is a translation surface. Yet, there is more (the proof can, once again, be found at www1.uni-ak.ac.at/geom/dld/canada-lines.pdf):

P1 M

P2 c∗1 c∗2 c2 c1 Fig. 7.66 If two coaxial helices c1 and c2 are reversely congruent, the midsurface is a surface of rotation.

When we rotate a sine curve (amplitude r) about its axis, the generated surface of rotation can be interpreted as a surface of translation with two reversely congruent helices that lie on cylinders of revolution with diameter r and contain the screw axis.

1 This

theorem competes in beauty with the theorem that every contour of a quadric for any projection is a conic section.

7.4 Translation surfaces

325

▸▸▸ Regarding rhombuses and huge towers

Fig. 7.67 Applications of the remarkable surface of revolution and translation. On the right: the Gherkin tower in London (Norman Foster ).

The aforementioned surface of revolution, which is at the same time a surface of translation, has several applications in practice. Fig. 7.67 on the left shows how polyhedra, entirely made up of rhombuses with constant side length but different interior angles, converge to a remarkable surface with a sine curve as its meridian. The corresponding adjacent sides of the rhombuses converge to helices. See also application p. 113. ◂◂◂

326

Further remarkable classes of surfaces

7.5 Minimal surfaces

Fig. 7.68 Under certain circumstances, surface tension can carry a coin, even if it has a greater density – the coin just needs to be small enough!

Due to surface tension, each liquid or elastic surface (such as a rubber membrane) strives to minimize its surface area. Mercury, for instance, accumulates into tiny round droplets if it is poured onto a planar glass plate. The spherical soap bubble similarly owes its shape to surface tension: A sphere simply covers the smallest possible surface for a given volume (Fig. 7.83, right).

helicoid

Scherk surface

catenoid Fig. 7.69 Special minimal surfaces emerge when the wire frame forms a cube, a helix, a pair of parallel circles, or a cube with only 8 edges (on the right).

Due to the surface tension of water, a small coin (Fig. 7.83) stays afloat, even though its much larger density would otherwise make it sink.

7.5 Minimal surfaces

327

If a soap film is bounded by a wire, it can arrange itself into many different forms. Fig. 7.69 shows some examples of shapes that the soap film can take when the wire frame fulfils certain conditions. In some cases, figures such as helicoids or catenoids can be generated. Open umbrellas are under a similar kind of pressure, as are tents and roofs.

Fig. 7.70 Surfaces exhibiting tension in theory and in Arts: Pictured on the left is the famous “chessboard minimal surface”, also known as Scherk surface; on the right, an installation by Maria Wambacher.

The principal curvatures must be of equal magnitude at each point Aside from the sphere, where all normal sections have the same curvature, the membranes of minimal surfaces can be geometrically distinguished by the fact that the surface’s principal curvature (see p. 261) are of equal size in each of their points. In every surface point, the Dupin indicatrix (Fig. 6.51) is, therefore, a pair of equilateral hyperbolas. The arithmetic mean of the two principal curvatures is the mean curvature. A non-spherical minimal surface has a mean curvature of zero everywhere. In every point, its Dupin indicatrix is a pair of equilateral hyperbolas. This is certainly the case for two minimal surfaces that we already know: the catenoid (Fig. 6.95 on the right and Fig. 7.83 on the left) and the helicoid (Fig. 7.12 and Fig. 7.69 on the right). Fig. 7.70 on the left shows a minimal surface named after Scherk in top and front view, as well as from a general perspective. ▸▸▸ Hyperbolic paraboloids are “almost” minimal surfaces. A computer test will show that the hyperbolic paraboloid comes close to a Schwarz minimal surface in certain areas. In Fig. 7.71 on the left, these areas are marked black (a very good approximation) and red (still a good approximation) – the top view is visible in the middle. The extent of the area that is colored black by the computer depends on the choice of a tolerance interval.

328

Further remarkable classes of surfaces

Fig. 7.71 The hyperbolic paraboloid resembles the so-called Schwarz minimal surface, and it does not significantly deviate from the “minimal condition”. The right-hand side shows a function graph that has the sum of the two principal curvatures as its function value. In order to be a “genuine minimal surface,” the graph would need to have a constant z value of zero.

Fig. 7.72 A minimal surface (gray) can be approximated quite well by a hyperbolic paraboloid (yellow). Right: Gossamers of caterpillars come close to minimal surfaces and therefore, also to hyperbolic paraboloids.

It is, nevertheless, possible to assume that a tent membrane spanned by a “skew quadrangle” is visually nearly identical to a HP shell (Fig. 7.71). Fig. 7.71 on the right shows the accompanying function graph, where the mean curvature (the mean of both principal curvatures) is indicated by the height value. In a “minimal surface”, the graph would have a constant z value of zero. ◂◂◂ ▸▸▸ Roofs of minimal surfaces Minimal surfaces can be characterized in two ways: physically (equilibrium of surface tension) and geometrically (opposing principal curvatures of equal size on the entire surface).

7.5 Minimal surfaces

329

Fig. 7.73 Minimal surfaces can be scaled without losing their useful properties.

This is why they keep their useful properties when they are scaled to huge dimensions (Fig. 7.73 on the right shows the Olympic Stadium in Munich). When working with other roof surfaces, one has to consider that the rapidly increasing weight may cause other problems. ◂◂◂ ▸▸▸ Sturdy sculptures with lightweight modules (Fig. 7.74)

Fig. 7.74 Minimal surface “populated” with modules morphing from triangular to hexagonal shape

Minimal surfaces can be quite useful for the creation of sturdy and lightweight sculptures, as the following experiment shows:2 First, a minimal surface 2 www.springchallenge2012.wordpress.com

(Bence Pap, Irina Bogdan, Andrei Gheorghe, Trevor Patt, Clemens Preisinger, Moritz Heimrath).

330

Further remarkable classes of surfaces

through four attractor points was created and subdivided by means of lightweight hollow modules. The geometry of the surface was then slightly changed according to circulation patterns (Fig. 7.74, left) and visual axes. The organic-looking structures pictured here boast an astonishing stiffness (which does not compromise their light-weight quality). The geometry was tested and improved by using the Grasshopper plugin “Karamba” (http: //www.karamba3d.com). ◂◂◂ ▸▸▸ k-noids

Fig. 7.75 The trinoid – unsurpassable beauty. In these two images, section lines parallel to the horizontal symmetry plane are displayed.

Fig. 7.76 To the left, the trinoid is covered by non-planar parameter lines. To the right, one can see section lines perpendicular to the vertical axis of the surface and meridian sections through this axis.

7.5 Minimal surfaces

331

The only surface of revolution which, at the same time, is also a minimal surface, is the catenoid. In differential geometry, a k-noid is a minimal surface with k catenoid openings. For k = 3, the surface is called trinoid (https: //en.wikipedia.org/wiki/K-noid). ◂◂◂ ▸▸▸ “Area-minimizing surfaces” Although speaking of a snail’s surface seems to make little sense given that it moves and changes shape all the time, we can make the following observation: The surface tends to minimize its area with any new position.

Fig. 7.77 Organic-looking surfaces that are computer-generated by iteratively minimizing the surface

When we gradually change the shape of a given surface by iteration in such a way that the area of the new surface is smaller than that of the previous ◂◂◂ one, the surface will eventually converge towards a minimal surface. ▸▸▸ An algebraic minimal surface and “something similar” In Chapter 13, we will see that exact geometric shapes are rarely found in nature. Sometimes, however, one finds rather good approximations of them, as Fig. 7.78 shall show (on the right, a computer drawing; on the left, “something similar” in nature . . . ). One of the simplest minimal surfaces is of degree nine, and it serves as an algebraic example of such surfaces in mathematics. If we consider only the innermost part, there are no self-intersections (the surface is theoretically infinitely large). If we compare the surface with a brown alga from the northern Adriatic sea, a certain similarity cannot be denied, indicating that the algae tend to minimize their surface area. ◂◂◂

332

Further remarkable classes of surfaces

Fig. 7.78 The comparatively simple algebraic minimal Enneper surface and some seaweed

Bending surfaces into each other At various points in this book, we have already discussed the process of development, that is, the flattening of a surface into a plane without distortion. In mathematical terms, this means that the surface metrics – its angles and also segments (measured geodesically, see p. 142) – are retained.

Fig. 7.79 Developable surfaces (e.g. bent paper strips of a rectangular or circular shape) can be flattened into a plane, and from there, they can be bent into any other developable surface. Klaudia Kosma applies this principle to design remarkable objects made of Möbius strips.

This applies to developable surfaces in an almost trivial way. These surfaces can be flattened into a plane or, vice versa, be formed from a plane surface piece. So, we only have to bend such a surface into a plane and then bend it again to create a new developable surface. Simple examples of that can be found in Fig. 4.87 and Fig. 5.6. Fig. 7.79 shows how an artist can be inspired by this principle, designing objects based on the Möbius strip. The ribbons

7.5 Minimal surfaces

333

are formed by bending strips of the plane surface. In the case of the creative clock on the left, the ribbons are not made of rectangular strips but of strips of a circular shape, which can be joined in an effortless and yet creative way. As you already know, doubly bent surfaces cannot be developed but, under certain – extremely restricting – circumstances, two such surfaces can be bent into each other. The theory underlying this claim is beyond the scope of this book, but we still know two surfaces that fulfill all criteria: the helicoid and the catenoid. Both are minimal surfaces and thus have the same mean curvature. (According to one criterion for bendability, it must be possible to match the surfaces in such a way that their corresponding points have the same Gaussian curvature.)

Fig. 7.80 According to Bonnet’s theorem, helical minimal surfaces can be bent into each other without destroying the surface metrics (i.e., there is no stretching or compression). If the catenoid is bent into the helicoid, we get an infinite number of minimal surfaces with the same surface metrics.

▸▸▸ Bending of minimal surfaces Fig. 7.81 shows once more the famous bending of a helicoid into a catenoid (compare Fig. 7.80). Fig. 7.82 illustrates the bending of minimal spiral surfaces.3 The helicoid is the only ruled surface (except the plane) that is a minimal surface (Catalan). Thus, it does make sense to vary parameters in the case of minimal spiral surfaces in the hope of eventually finding a ruled minimal spiral surface. The catenoid is the only minimal surface of revolution. This was first documented by Leonhard Euler . 3 W.

Wunderlich; Beitrag zur Kenntnis der Minimalspiralflächen. Rend. Mat. 13, pp.1–15, http://sodwana.uni-ak.ac.at/geom/mitarbeiter/wallner/wunderlich/pdf/59.pdf.

334

Further remarkable classes of surfaces

Fig. 7.81 Bending of a helicoid (orange) into a catenoid (yellow): Note the motion of the orthogonal grid that is drawn on the surfaces – its metric is not changed!

Fig. 7.82 Bending of minimal spiral surfaces according to Wunderlich. The yellow surface is symmetric to a horizontal plane, the orange surface is axially symmetric.

Since the catenoid is the only minimal surface of revolution, Fig. 7.83 (a floating aluminum coin) allows the conjecture that the deformed water surface is, in principle, a catenoid, because the surface tension will deform the water surface in this way. ◂◂◂

7.5 Minimal surfaces

335

Fig. 7.83 A floating coin is very likely to deform the surface of the water along a catenoid.

▸▸▸ Bending of nudibranches and algae

Fig. 7.84 A nudibranch (Aplysia) appears to “fly” through shallow water. Parts of the surface resemble minimal surfaces. If this is the case, the fairly firm but flexible tissue undergoes no changes in the metric unless it is moving.

Fig. 7.85 Brown algae swaying in the occasionally strong current in shallow water

In both Fig. 7.81 and Fig. 7.82, a rectangular grid on the surfaces is drawn in order to see that the metrics of the surface do not change during the bending process. This is unique for minimal surfaces, and it may also be an explanation for the following: Surfaces of maritime creatures like nudibranches (Fig. 7.84) or also plants like algae (Fig. 7.85) sometimes resemble minimal

336

Further remarkable classes of surfaces

surfaces. When they glide or sway in the current, their flexible but rather firm tissue does not need to change essentially. ◂◂◂ The second example (Fig. 7.86) seems less intuitive, and yet, it fits the context very well: Crocheted surfaces can be bent easily without losing their metric properties in the process.

Fig. 7.86 Pliable surfaces: Lilian Boloney crochets (!) complicated mathematical surfaces: This image shows Boy’s surface, which can serve as a model for the projective plane. The pliable material allows for bending without significant changes to the surface metrics. The artist was inspired by a scientific paper (http://vis.berkeley.edu/papers/methexpview/math_exploded_view_small.pdf).

8

The endless variety of curved surfaces

So far, we have learned about several classes of surfaces. Many other classes of surfaces may, however, be derived from a variation of so-called parameter representation. In the age of computer-aided creative (architectural) design, it is becoming increasingly relevant to create completely general surfaces by means of easy-to-control geometric instructions. Such free-form surfaces are the topic of this chapter. The theory behind free-form surfaces is already several decades old, and the rapid nature of modern computers makes such surfaces interesting for any designer working in front of a computer screen. The problems to be solved are the following: How can we find surfaces that pass through predefined points in space and additionally follow certain “boundary conditions”? How is it possible to work with such “control points” and retain the ability to change their individual positions without affecting the character of the entire surface? The solution to these problems lies, as it often does, one dimension below: One should define planar free-form curves that exhibit certain properties and then transfer these properties into three-dimensional space. Thus, we are confronted with Bézier surfaces and B-spline surfaces by way of Bézier curves and B-spline curves. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_8

337

338

The endless variety of curved surfaces

8.1 Mathematical surfaces and free-form surfaces Function graphs

Fig. 8.1 A graph of a so-called “smooth” function

The graph of a “smooth” function (Fig. 8.1) shows a smooth curve at every point in every direction. The tangent vectors of these smooth curves are determined by the partial derivatives with respect to x and y, which span a uniquely defined tangent plane that contains all tangents arising from perpendicular sections. In this case, the given function is said to be totally differentiable.

Fig. 8.2 Two graphs which are not totally differentiable everywhere.

Fig. 8.2 shows two functions that are not differentiable everywhere. In the √ 2 2 figure on the left (right circular cone, z = √x + y ), the function is not differentiable at the origin. On the right (z = ∣xy∣), the partial derivatives exist along the x- and y-axis, but there is no tangent plane in the sense described above.

8.1 Mathematical surfaces and free-form surfaces

339

Fig. 8.3 The “pathological” Weierstrass-℘-Function

Without going into details, Fig. 8.3 shows the famous Weierstrass-℘ -Function and its derivative, which can also be interpreted as a function graph.

Fig. 8.4 Function graph with a “mathematical background” (simulation of the heat distribution over the candle pictured in Fig. 1.8). The layer stripes are algebraic curves of degree-four, which can only be represented correctly when the surface is described by an equation with exact precision.

More general surfaces described by mathematical equations Many well-known surfaces can be described by mathematical equations. This includes (but is not limited to) practically all surfaces that we have discussed so far and, of course, quite a few others (Fig. 8.4 and Fig. 8.5 show three examples). Such “mathematical surfaces” possess one or many shape parameters, which permits a certain variation in their visual appearance. With some mathematical dexterity, even fairly complex surfaces can be generated. A very elegant piece of furniture by Paolo Piva is pictured in Fig. 8.6. The idea behind it was to involve mathematics in the arts.

340

The endless variety of curved surfaces

Fig. 8.5 Surfaces generated by mathematical equations (on the right: Klein bottle in theory and practice.

Fig. 8.6 Furniture as a mathematically defined function graph

This surface is defined by a symmetrical equation that may also be of interest to non-mathematicians: z = c⋅(y sin x−x sin y) where c ≈ 0, 12, x, y ∈ [−π, π]. Parabolic points occur along the coordinate axes. Artists who work with ceramics are often inspired by mathematics. In Fig. 8.7, Martina Zwölfer presents some of her work (see also Fig. 8.5 on the right).

Fig. 8.7 Ceramics as a “playground” for mathematically defined surfaces

8.1 Mathematical surfaces and free-form surfaces

341

Different types of surfaces Surfaces can generally be thought of as the “products” of space curves that undergo arbitrary motions and deformations. Surfaces of revolution, for instance, are created by the rotation of an unchanging generatrix. Scaling this curve in relation to a fixed point on the axis of rotation and proportionally to the angle of rotation yields a spiral surface.

The addition and subtraction of surfaces Many objects that seem highly complex are the result of so-called Boolean operations: Solids can be “added” to each other, but also “subtracted” from each other. To the geometer, this does not necessarily indicate that a new surface was created: Each boundary segment, no matter how small, belongs to precisely one of the initial surfaces.

Fig. 8.8 Boolean operations in architecture and the arts: “tree house” (cube apartment in Rotterdam by Piet Blom), where a cube was placed on its spatial diagonal and superimposed by a hexagonal prism. At the center: addition and subtraction. The right side pictures a tree house of a different kind: Erwin Wurm placed a house on top of the Vienna Museum of Modern Art – a classical Boolean subtraction is behind this effect.

Fig. 8.9 Boolean operations were used to project the initials of three great masters: Gödel, Escher, Bach. The B is turned upside down, the E is rotated by 90○ – both are translated along the coordinate axes, which yields the intersection of the desired residual solid (see, e. g. [19]).

342

The endless variety of curved surfaces

Fig. 8.10 Boolean operations in art objects (Eduardo Chillida)

Fig. 8.11 Extreme Boolean “subtraction”: The high-speed photograph shows an apple that has been penetrated from the right by the bullet of an air rifle. The double-cone-shaped projectile (encircled) is fairly easily recognizable. On the right: computer models.

Milled surfaces are also “mathematical surfaces” During the milling process, the cutter envelops a manifold in all possible positions – the sum of all milling positions. The surface parts that are cut away are the differential surfaces of the original solid and this enveloped manifold. The more complicated the shape and motion of the cutter, the more intricate this enveloped surface. Fig. 8.15 and Fig. 8.16 show a surface designed by Florian Gypser. When looking only at the intermediate positions of the object in motion (the professional calls this a discrete family), one cannot fail to notice the aesthetic quality of these “imprints” – their possible applications in design are likewise obvious. In practice, curved shapes are often produced by milling. Each milling stage creates a new and occasionally complicated shape (Fig. 8.13).

How can we solve the problem? Generally speaking, surfaces of arbitrary shape can, to some degree, be approximated by parts of standard surfaces. Due to the limited number of shape parameters, however, the result will rarely be satisfactory. From this point on, let us define a free-form surface such that its appearance may be changed in an almost arbitrary manner through the variation of parameters and generating geometric elements. Thus, it should be possible to at least visually approximate mathematically defined surfaces very closely.

8.1 Mathematical surfaces and free-form surfaces

343

Fig. 8.12 simple cutters (cylindrical and conic)

Fig. 8.13 Surfaces as the results of a milling process . . .

Free-form surfaces play an important part in industrial design (e. g. in the auto industry, as in ship and airplane construction) and in the modeling and construction of interesting architecture.

Surface theory is helpful in the creation of categories We know the following from the previous chapter: Locally speaking, there exist only three types of surfaces – regardless of whether they are free-form or mathematically defined: Each surface, regardless of its complexity, is curved like an elliptic or hyperbolic paraboloid – and in some borderline cases, like a parabolic cylinder or a plane – in the small neighborhood of a point. It makes no difference for our prior considerations whether the surface is mathematically defined or “free-form”. As we shall soon discover, free-form surfaces also have to be calculated in some way – by means of relatively elaborate, “recursive” algorithms, to be exact. Due to their complicated definition, a greater quantity of shape parameters are relevant in this context. ▸▸▸ Playing with geometric forms A torus can be generated via rotation of a circle around an axis in its carrier plane. When we vary the radius of the circle (e. g., harmonically by introducing a sine function), we might get something like what is shown in Fig. 8.18 on the left. This slightly resembles a pumpkin or a juicy tomato

344

The endless variety of curved surfaces

Fig. 8.14 . . . and an application of an altogether different kind

Fig. 8.15 Envelope or “imprint” of an object in motion

(Fig. 8.19), though such natural objects hardly ever have such extremely symmetric shapes. So, it might be useful to vary another parameter, namely the rotation speed of the circle in relation to the change of the circle’s radius. In the case of Fig. 8.18 on the right, an acceleration factor of 2.32 was taken. Why this precise factor, which you probably did not expect? Well, it could have been any other number, except for a simple fraction like 3/2 or 5/2, because these fractions would then again result in too much symmetry. This goes somewhat against classical mathematical approaches, where simple fractions usually lead to remarkable results, but it comes closer to a simulation of natural behavior.

Fig. 8.16 Imprint of a “discrete” family

8.1 Mathematical surfaces and free-form surfaces

345

Fig. 8.17 Partly developable surfaces (Bilbao Museum)

Fig. 8.18 From a perfect geometric shape to a pumpkin or a tomato

Fig. 8.19 Tasty tomatoes

Now, the surface resembles our pumpkin or tomato even more. . . But what is the benefit of all this? Can we learn something from it? Answering these questions is rarely easy. Such an approach may or may not help us understand how nature produces such remarkable shapes. Even if we find a good approximation of a shape by means of formulas, nature might not have followed those rules to get there. One always hopes to discover “a good explaination” for why nature functions the way it does. In cases where we

346

The endless variety of curved surfaces

cannot identify the proximate cause in the evolution of a specific form, we should consider the possibility that this form may have been produced by selective breeding of individuals with certain characteristics. ◂◂◂ ▸▸▸ The shape of a virus Viruses are extremely small. They are, in fact, the smallest and simplest life form known. The average size of a virus could be 100 nanometres, i.e., a tenth of 1/1000 millimetre. In comparison, bacteria are up to a hundred times larger. Therefore, it is possible to detect bacteria with an ordinary microscope, whereas viruses are only visible under an electron microscope.

Fig. 8.20 World’s most infamous virus during the time this book was written in 2020 . . .

The three-dimensional structure of the coronavirus (Fig. 8.20) was discovered by means of an imaging technique called cryo-electron tomography. The spikes on the surface of the virus (to which it owes its name, which means “crown”) are the point of contact between the virus and the host cells that line the airways of a human’s lung. The spikes connect with the lung cells by sliding into matching receptor sites found on those cells. Once secured, this connection enables the virus to fuse with the host cell, injecting its genetic material into it, and instructing the host cell to make thousands of copies of the virus. In computer animations, the shape of the virus can be captured by means of purely geometrical elements: Define a sphere, look for evenly distributed points on its surface and add a prototype of a spike there. Since such a prototype is a surface of revolution, it is a good idea to define its meridian by using only a few points and then joining them with a smooth curve. The following section will explain how this can be done. ◂◂◂

8.2 Interpolating curves and surfaces

347

8.2 Interpolating curves and surfaces There is one obvious way of approaching a definition of free-form surfaces: It should be possible to fix single surface points as control structure and interpolate the points in between. If a surface is to be given in the form of a computer model, it may be digitized (using keyers, laser scanners, or photographs) into a wireframe model on the surface, from which the remaining points in space may be computed. In order to connect n + 1 coplanar points by a smooth curve, it seems logical to position an degree-n order parabola p through the points.

Fig. 8.21 polynomial function vs. cubic spline

This approach may not be of much use to designers: Such curves tend to oscillate – especially at the boundaries (Fig. 8.21 on the left, curve p). Another technique assembles the curve piece by piece from degree-three parabolas, while the separate curves are joined at the respective endpoints with “continuous curvature” (curve s in Fig. 8.21). These curves are called “cubic splines”.

Fig. 8.22 The choice of control points may be significant.

In order to achieve a smooth curve, the control points of a cubic spline should be evenly distributed, as unexpected results may occur otherwise (Fig. 8.22). Curves through predefined points may also be produced by so-called NURBS (which will soon be described). By using interpolating splines, it is possible to describe surfaces whose mathematical definition is no longer feasible. In Fig. 8.23 and Fig. 8.24, for example, the cross-sections of animal horns are described by means of interpolating splines before the horns undergo mathematical transformations (a helispiral motion is pictured). The shell of a nautilus was created in a similar manner (Fig. 8.25).

348

The endless variety of curved surfaces

Fig. 8.23 Approximation of animal horns using cubic splines

Fig. 8.24 Another approximation (blackbuck antelope horns)

Fig. 8.25 The shell of a nautilus is created by defining a symmetric space curve that undergoes a spiral motion.

▸▸▸ Growth spurts Since we uncovered the laws of growth for snail houses and antelope horns

8.2 Interpolating curves and surfaces

349

rather effortlessly in the previous part, we should also be able to find out what rules apply for antler growth.

Fig. 8.26 Antlers regrow every year

Fig. 8.27 Photos of an antler from four different angles

Fig. 8.26 shows two different stages of growth (Wapiti), whereas Fig. 8.27 shows one and the same antler from different angles. Obviously, there is neither exponential growth nor rotation involved in the growth, but there is evidently one underlying rule, that guides this kind of (rather fast) growth.

350

The endless variety of curved surfaces

Fig. 8.28 illustrates how antlers grow under different parameters. One of these parameters is the number of endings that will eventually be produced. (For male deer this means the older the animal, the more endlings there are.)

Fig. 8.28 Simulation of antler growth (changing with the age of the deer)

The growth proceeds in several steps: So-called “sleeping positions” start growing at a later stage, while already existing parts continue growing, producing more “sleeping positions” for the next stage. A growth in different stages or growth spurts, each boost with changing parameters. ◂◂◂

Direct modeling at the computer Designers are, of course, not interested in specifying formulas and would rather do their ingenious design work directly at the computer. The Bézier and B-spline surfaces, which allow for the easy definition of free-form shapes, were developed for this precise reason. In order to comprehend the underlying principle, we shall first discuss Bézier and B-spline curves in the plane before proceeding to the Bézier- and Bspline-surfaces in three-dimensional space.

8.3 Bézier- and B-spline-curves

351

8.3 Bézier- and B-spline-curves Bézier curves Prior to B-spline curves, Bézier curves are the most important mathematical representation of curves in computer graphics and computer-aided design (CAD). They were introduced in 1962 by P. Bézier at Renault and are defined by a so-called control polygon. The number of polygon sides denotes the degree of the curve.

Fig. 8.29 the de Casteljau algorithm, inflection point, conic sections

The construction procedure for a curve point corresponding to the real parameter t was already defined by P. de Casteljau (Citroen, 1959) and goes as follows: Subdivide all n sides of the polygon following the same ratio t ∶ (1−t) (in Fig. 8.29, t = 0.5 was chosen on the left and t = 0.75 on the right). The connecting segments of the new points form another polygon – with one side fewer than the original polygon. This procedure is repeated for the new polygon, which yields another polygon with n − 2 sides, and so on. After n steps, the polygon is only composed of a single point – the curve point at the parameter t. The last segment is the curve tangent at this point. In the special case of n = 2, this procedure always yields a parabola. Fig. 8.29 on the center right shows a degree-four Bézier curve with an inflection point defined by a four-sided polygon. On the far right, a degree-two Bézier curve is pictured in black – a regular parabola. Due to the nature of their construction, Bézier curves possess many helpful geometric properties: They always lie within the convex hull of the control polygon and pass through the endpoints. At the endpoints, the curves touch the first and last segment of the control polygon. The curve does not oscillate needlessly, which means that it does not intersect an arbitrary straight line more often than the control polygon. Furthermore, in the cases of rotations, reflections, translations, scaling, and parallel projections, it is sufficient to subject the control polygon to the same transformation. The construction procedure for curve points and tangents is invariant under affine transformations. The control points are transformed into the control points of the image curve. Besides the calculation or construction of points and tangents, de Casteljau’s algorithm serves another useful purpose: the decomposition of a Bézier curve

352

The endless variety of curved surfaces

at a point t ∈ [0, 1] into two parts (Bézier curves of the same degree, Fig. 8.30). It also provides the key for the approximated calculation of all intersection points of two Bézier curves, or of a Bézier curve and a straight line.

Fig. 8.30 augmentation of the degree, decomposition of a Bézier curve

If a single control point of a Bézier curve is moved, then the shape of the entire curve is affected (consider the global influence of the control points)! This is a significant disadvantage of Bézier curves compared to B-spline curves. The same comparison can be done with Bézier- and B-spline surfaces. It is further problematic that certain frequent types of curves, like ellipses or hyperbolas, cannot be precisely defined as Bézier curves (as opposed to parabolas). In order to solve these problems, Bézier curves were generalized to so-called rational Bézier curves.

Rational Bézier curves Weights are assigned to each control point. If all weights are the same, then a classical (“ordinary”) Bézier curve is given. The geometric definition of a Bézier curve is independent of dimensions (Fig. 8.31): Let us imagine the planar curve in a horizontal plane at height 1 and stretch the points of the planar control polygon from the origin, with the respective weight as the scaling factor. In the general case, we will thus get a nonplanar control polygon in three-dimensional space that will, if exposed to the de Casteljau algorithm, yield a Bézier space curve. The central view of this curve from the origin into the original curve’s horizontal carrier plane produces the rational Bézier curve. This approach allows us to define other curves apart from parabolas, such as parts of ellipses (including parts of circles) and parts of hyperbolas (see Fig. 8.29 on the right), which occur as central views of parabolas. For rational Bézier curves, the properties of regular Bézier curves essentially persist. It may, however, be added that even projective transformations will not change the nature of the curve: It is sufficient to apply the transformation to the control polygon. The rational Bézier curve produced by the transformed polygon corresponds to the projective transformation of the original Bézier curve.

B-spline curves By piecing together rational Bézier curves (the transition can occur at constant curvature if the degree is at least 3), so-called Bézier splines may be produced. They have the tremendous advantage that changing a single con-

353

8.3 Bézier- and B-spline-curves

Fig. 8.31 spatial interpretation

Fig. 8.32 above: ordinary, below: rational Bézier curves

trol point no longer affects the entire shape on a global level. On the other hand, the amount of data for the control points may grow to be very large, as Bézier splines are “reluctant” to adapt to arbitrary – and especially convex – shapes. In the general case, they thus require a large number of control points for fine-tuning. This disadvantage was overcome by J. Ferguson (at Boeing) in 1964 through the invention of B-spline curves, which otherwise possess properties very similar to those of Bézier splines. For B-spline curves, the algorithm analogous to de Casteljau’s is the so-called de Boor algorithm. The kinship between Bézier curves and B-spline curves is such that each B-spline curve segment can be converted into a Bézier curve. The degree of the curve indicates how many control points around a curve point are responsible for its position. In order to quantify this degree of influence, a “knot vector” is given to specify the strength of the influence that a control point’s neighbors have. This vector must possess more components than the overall amount of control points. If a curve is to pass through the boundary points of the control polygon, the beginning and end components of the knot vector must be repeated accordingly (see the following example).

Rational B-spline curves (NURBS) If weights are provided for all points of the control polygon (as is the case with rational Bézier curves), we get a rational B-spline-curve, which is also called a Non-Uniform Rational B-Spline (NURBS) curve. “Non-uniform” simply means that the knots do not have to be distributed at equal distances. The unit circle, for instance, can be specified by the control polygon (1, 0), (1, 1), (−1, 1), (−1, 0), (−1, −1), (1, −1), (1, 0), the knot vector (0, 0, 0, 14 , 21 , 12 , 14 , 1, 1, 1), and the weights (1, 12 , 21 , 1, 12 , 12 , 1). Based on this representation of a circle, it is possible to construct surfaces of revolution. NURBS possess properties analogous to those of ordinary B-spline curves: local control, the convex-hull-property, and continuity of curvature (if all weights are positive) as well as invariance under affine and projective transformations. There exists a de Boor algorithm for NURBS which can be used to calculate the points of the curve or decompose a NURBS into two parts.

354

The endless variety of curved surfaces

8.4 Bézier- and B-spline surfaces Given a grid of quadrangles instead of a control polygon (m × n sides), Bézier surfaces and B-spline surfaces can be constructed by analogy with Bézier curves and B-spline curves: If Pij are the points of the grid (i = 0, . . . , m; j = 0, . . . , n), then the n + 1 points with a fixed i define the control points of a Bézier- or B-spline curve. For each of these m + 1 curves, there exist unambiguously defined points for each parameter t as calculated by the algorithms of de Casteljau or de Boor . These points may, in turn, be used as the control points of further Bézier- or B-spline curves. We have thus defined a continuous family of curves on the surface. By analogy, an additional family of curves may be constructed by varying the index i while keeping j constant.

Fig. 8.33 Bézier surface

Fig. 8.34 Subdivision (degree augmentation + local change)

When compared to their planar cousins (Bézier curves), Bézier surfaces exhibit similarly practical properties for modelers: The surface passes through the outer edge points of the grid and is touched at this point by the planes spanned by the respective sides of the quadrangular net. The surface lies within the convex hull of the grid. In order to apply an affine transformation to the surface, it is sufficient to apply the transformation to the grid. Rational Bézier surfaces (which will be discussed shortly) are even projectively invariant. Once again, difficulties arise when changing a single control point affects the entire surface. It may be helpful to increase the degree of the surface temporarily, decompose it into parts, and continue manipulating the separate parts only. If both surface degrees m and n are at least 3, then it is possible to configure the surfaces so that they meet at constant curvature along edges. For a designer, constant curvature is of utmost importance: Shiny surfaces that do not have this property produce light edges. Ruled surfaces and cylinder surfaces can easily be represented as Bézier surfaces by reducing one of the two degrees m or n to 1. In the case of the cylinder, the straight lines connecting corresponding control points must be parallel. Paraboloids occur for (2, 2) grids (but only the surfaces of translation among the (2, 2) grids are paraboloids). If the polygons of the quadrangle grid diverge as a result of translation, then a surface of translation is created. An exact representation of mathematical surfaces through Bézier surfaces

8.4 Bézier- and B-spline surfaces

355

is possible if the mathematical surfaces possess a parameter representation composed of polynomial functions.

Generalized Bézier surfaces If each grid point of a Bézier surface is specified with a weight, the result is a rational Bézier surface. Now it is possible to represent a greater class of surfaces in an exact manner – in fact, this applies to all surfaces whose parameter representation can be specified as a rational function (a fraction of polynomial functions). However, even such techniques can only encompass the tip of the iceberg of all possible surfaces, which is why it is recommended to work with sub-grids or sub-nets that can be edited separately.

Fig. 8.35 Rational B-spline surfaces, open and closed

Like B-spline curves, B-spline surfaces can be manipulated locally. They also share useful properties analogous to those of B-spline curves. Fig. 8.35 shows open and closed control grids and the corresponding surfaces.

Fig. 8.36 Rational B-spline-surfaces (NURBS), open and closed

Rational B-spline surfaces (NURBS surfaces) are the most flexible if, in addition to the control points, they can also be affected by two knot vectors for both directions. These surfaces are, thus, included in the design modules of all relevant CAD systems. ▸▸▸ Practical construction After a free-form surface has been designed on the computer, problems usually tend to occur during the practical construction. Rapid prototyping permits the quick and easy generation of prototypes: Three-dimensional “printers” produce thin cross-section surfaces from synthetic material which can then be glued together.

356

The endless variety of curved surfaces

Fig. 8.37 A nice application of NURBS (compare Fig. 2.32)

Fig. 8.38 The practical construction of a NURBS blueprint

Large surfaces demand adequately enormous means. A patent which specifies the computerized control of bending machines so that an exact wireframe model of the surface is produced from steel (Fig. 8.38) was submitted at the University of Applied Arts Vienna (by Sigrid Brell-Cokcan and Dumene Comploi, design by Mario Gasser, Cornelia Faißt, and Lis Ehses). ◂◂◂ ▸▸▸ Nutshells made of plastic An interesting idea by Marcus Bruckmann and Ursula Klein/schulteswien describes the welding of congruent, circular plastic foils which can then be inflated. The resulting formations have Platonic solids as their base frame (Fig. 8.39), and their shapes recall the shells of Brazilian nuts. They were modelled using ◂◂◂ NURBS in a particularly realistic way.

8.4 Bézier- and B-spline surfaces

Fig. 8.39 Surfaces under pressure, derived from Platonic solids

Fig. 8.40 “Inflated” cube and dodecahedron using NURBS

357

358

The endless variety of curved surfaces

8.5 Surface design done differently An interplay between art and geometry An unorthodox question posed by the ceramicist Silvia Siegl and its surprising solution on the computer led, in turn, to a series of projects.

Fig. 8.41 The initial question . . .

At first, the problem concerned merely the rigid connection of ceramic lenses using two orthogonal rods of equal length and the subsequent bending of the construction into certain shapes. This was to be accomplished by using spherical joints at the ends of the rods (Fig. 8.41). Initially, the geometric analysis aimed at fitting squares with their respective corners into the joints. This does not pose any problem in the plane, where it is simple to proceed along the square edges following the creasing of the “lens carpet.” This creasing is only possible if it leads to a change of position in multiple lenses.

Fig. 8.42 . . . was solved in a first step by Franz Gruber with the use of a computer.

Let us now replace the lenses by small magnetic spheres, from which four attached magnetic rods of equal length protrude. This flexible magnetic net can, indeed, be fitted to the desired forms. In the illustration Fig. 8.43, the net was cast over two spheres. The possibility of approximating free-form surfaces through “magnetic nets” was thus discovered. Groups of four rods are thereby arranged into “skew

8.5 Surface design done differently

359

Fig. 8.43 Casting the net over a scene: a “quadrangulation” of a different kind

rhombi,” which may be decomposed into two triangles along one of the two available diagonals. The resulting triangulation has the advantage that all triangles are isosceles and of “similar size.”

Fig. 8.44 Load tests in theory and practice

As advantageous as the new method of triangulation may seem, the boundaries appear to be out of control. One may ponder what would happen if the four corners of a rectangular magnetic net are specified in their final position. The solution of this problem is more complicated and, indeed, there is no exact solution in the general case. This seems to necessitate the stretching or compression of the rods by as little as possible. Fig. 8.42 on the left illustrates – by use of yellow and red colors – where a strong material strain may occur in a practical construction. The project thus reached new dimensions and culminated in a simulation program for the manufacturer of a magnetic-geometric “toy”. Several renderings of that program can be seen in this book (such as Fig. 3.40).

360

The endless variety of curved surfaces

A different kind of architectural draft We have often mentioned the fact that developable surfaces play a crucial role in architecture, as they can be constructed without the tedious technique of triangulation and yet lose none of their curved beauty. Examples are legion: Fig. 8.45 once again shows two lovely applications. A further question arises: How should architectural forms be designed so that they are guaranteed to be developable? Architects have their own methods to accomplish this task: They work, for instance, with bendable strips of varying materials which are then fitted into the desired arrangement (Fig. 8.46).

Fig. 8.45 Developable façades exhibit an attractive elegance. On the left: Santiago Calatrava’s opera house in Tenerife (cone parts), on the right: Frank O. Gehry’s New Zollhof in Düsseldorf

Once a model is supposed to enter an advanced phase, it needs to be transferred into the computer program. At this point, some small compromises have to be made: No program – so far – supports the construction by means of bendable strips. What was previously developable now becomes a general free-form surface. The difference may not be visually perceptible, but when the time comes to create practical constructions, the simple construction from developable parts is largely over, and the façades will have to be triangulated or manufactured in a complicated, doubly curved way.

Fig. 8.46 Classic sketch using strips: Lars Spuybroek, Centre de Musique Pop, Nancy (left). The respective sketch using a custom-built computer program (right).

The University of Applied Arts Vienna attempted to develop such a software package and published the results in [10]. It permits the use of curves instead of surfaces during modeling (Fig. 8.46 on the right). These are then interpreted as the midlines of “paper strips,” which are also the rectifying

8.5 Surface design done differently

361

Fig. 8.47 Design using strips and the result (left)

developables of the curves. The curves themselves can be created and manipulated through NURBS. During practical construction, some challenges necessarily arise, but they can luckily be solved: The midline cannot possess any arbitrary form because the developable that is derived from it must not self-intersect. Geometrically speaking, this can be avoided by calculating the edge of regression of the developable. If it approaches the midline “too closely,” the designer must not induce any further deformations in that area. This may be a restriction during design, but it also guarantees that the shape is realistic and does not need to be manipulated at a later stage.

Fig. 8.48 Design using strips: In conjunction with modified Boolean operations, only small numbers of such elements are necessary to create interesting developable shapes (Hans Hollein).

362

The endless variety of curved surfaces

Fig. 8.49 Design using strips: All surfaces are developable and therefore ease to build.

Fig. 8.50 Another example for design using strips

Fig. 8.51 The advantage: The development of the whole object is immediately at disposal.

9

Photographic image and individual perception

This chapter is dedicated to central projection, which comes into play both in single-eyed human vision and in photographic imaging. A simple pinhole camera is enough to realize this kind of projection, but the way in which the human eye resolves the image is much more complicated due to the fact that the image plane is not flat. Ever since the painters of the Renaissance, perspective images have been brought to a high standard. Knowledge about vanishing points and vanishing lines (such as the horizon) is especially important in this context. Thus, we will put special emphasis on these topics. We shall discuss several techniques for quickly achieving good results in perspective drawing, even though the level of difficulty remains considerable. A complete understanding of the “intersection method” is essential for this purpose. Although complex perspective images are not often drawn these days, a theoretic understanding is required in order to rectify and interpret such images correctly (photographs, for instance). Finally, we shall discuss alternate central projection, where the projection falls onto cylinders or doubly curved surfaces – which is also true for natural vision. The position of a future spectator is the decisive element of central projection, because the observation of a perspective image is another central projection. One should aspire to a reasonable combination of both projections in order to produce the desired visual effect. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_9

363

364

Photographic image and individual perception

9.1 The human eye and the pinhole camera For a long time, it was believed that the perspective images created by the pinhole camera (and thus, essentially, by any regular camera) are virtually identical to the visual image of the three-dimensional world that we perceive with one eye closed. A famous experiment by Filippo Brunelleschi was presented as “proof” of this claim in the year 1401(!):

Fig. 9.1 The iris and its different “apertures”

A spectator looks through a tiny hole in the wall onto a spatial object (the object used in Brunelleschi ’s experiment was the Florence Baptistery). This hole is then covered, and a realistic perspective painting of the spatial object is inserted between the spectator and the object. When the hole is then uncovered, the spectator would fail to notice a difference, thinking that they were still looking at the original object (Fig. 9.2). Brunelleschi even took his experiment one ingenious step further: He inserted a mirror instead of a painting, and in this mirror, the spectator would see a reflection of the perspective that was painted on the backside of the wall with the hole. This construction amounted to the same effect. In fact, if the eye is forced into a specified position with regard to the observed object, then the visual perception is identical to that of a central projection from that position. If this restriction is not given, then the mere change of position would lead the one-eyed spectator to realize (even in a darkroom

9.1 The human eye and the pinhole camera

365

under otherwise perfect conditions for “illusions”) that they are looking at a two-dimensional picture that ceases to appear realistic from other vantage points.

Fig. 9.2 Brunelleschi’s ingenious idea interpreted by Otmar Öhlinger

Spheres are quite particular. In classical perspective (photography), the contours of a sphere most often appear to be an ellipse (the remaining conic sections rarely occur in practice). The contour ellipse is at its most eccentric if the center of the sphere is farthest away from the optical axis (the principal ray). However, if a spectator is positioned in the right place, then the sphere contours will, without a doubt, be interpreted as circular. This is hardly surprising: The projection cone of the ellipse through the eye is a cone of revolution. If the observer leaves the ideal position, then the projection cone becomes a general quadratic cone, and the observer will notice that “something appears to be wrong with the sphere.”

Fig. 9.3 Almost circular contours of a sphere Fig. 9.4 Section through the near-spherical eyenear the center of the image! ball

When looking at a sphere, we unconsciously move it into the center of our field of view. The optical axis becomes the connection between the eye and the center of the sphere. This may occur either through a rotation of the head or through the largely equivalent rolling of the eyes. The contour of the sphere now appears as a circle. Yet, how is this circle transferred via central projection onto our retina? Due to the laws of optics (the vitreous

366

Photographic image and individual perception

body with the built-in optical lens being precisely being precisely an optical device adhering to these laws), a cone of revolution whose axis corresponds to the optical axis is to be intersected with a sphere (the near-spherical retina). This, indeed, produces a circle on the curved retina. The optical nerves need only transmit the image to the brain, where – based on our past visual experience – the curved impression is imagined as a spatial object. A second image, generated by the second eye, is simultaneously processed.

Fig. 9.5 Iris and pupil, curvature of the cornea (left); strange effects due to “image raising” (right)

This whole procedure is anything but simple. However we perceive threedimensional space, the following model is very fruitful for its understanding: Actually, we do not measure lengths but visual angles. For us, a circle is not a curve whose points are equidistant from a given center. Instead, a circle is a curve where the lines of sight through their points enclose constant angles with the optical axis, producing a cone of revolution. Curves that run across the same cone of revolution are, indeed, often intuitively interpreted as circles until a change of eye position corrects the false impression.

9.2 Different techniques of perspective

367

9.2 Different techniques of perspective This chapter concerns the construction of perspective images which, in days of old, provided considerable assistance during the creation of perspective images. In the age of computer graphics, where the art of manually drawing perspective images is dying out, there still exist substantial reasons for understanding the procedures behind construction. Firstly, sketches with a correct image may still be in demand in the future, though this may only concern the artistically inclined. Secondly, knowledge about correct construction may help when approaching highly relevant problems today – especially those which fall into the purview of “reconstruction” – right up to the understanding of 3D scanners!

Fig. 9.6 In both cases, the principal projection ray (the optical axis) is horizontal. On the left side, it is even perpendicular to the back wall (frontal perspective).

Fig. 9.7 In both cases, the principal projection ray is directed upwards – on the left, vertically. In both cases, the goal was to preserve the symmetry of the main directions (Cathedral of Trier).

Intersection method A perspective image is the result of central projection. Points in space are depicted by projection rays that are intersected with the image plane. Technical

368

Photographic image and individual perception

objects tend to have mutually orthogonal “principal directions”. We shall first assume the image plane to be parallel to the upright direction. This allows us to gain a better understanding of certain procedures – a generalization at a later point should not cause any problems. In Fig. 9.8, the object is positioned oblique to the image plane π (see the top view). The desired perspective image is the intersection of the viewing pyramid emanating from the eye point E with the image plane π. Due to the special assumption (π ∥ π2 ), the front view of the figure that is cut off from the pyramid is identical to the desired perspective image. The front view of E is the principal point H of the perspective image. The orthogonal distance Eπ = EH is the distance d. The circle centered at H with radius d is called the distance circle. • Horizon and principal vanishing points The base plane γ is horizontal. Each point at infinity in γ possesses an image which is called the vanishing point. The vanishing points of all horizontal directions (in γ) converge on the horizon h which passes through H. Therefore, the horizon is a vanishing line (common to all horizontal planes). In particular, the points at infinity of both horizontal principal directions possess the vanishing points F1 and F2 , which can be generated by parallel translation of the directions through the eye point. This construction makes us realize the following (see Fig. 1.40): The vanishing points F1 and F2 of orthogonal directions lie anti-inverse with respect to the distance circle. ⊕ Remark : The distance circle should not be missing in any perspective image. All parts of the image that lie outside of this circle are highly distorted and would usually appear “unnatural” to a spectator – we shall later discuss this matter in more detail. “Classical perspective images” normally lie well-embedded in the “half-distance circle.” This means that the viewing cone around the optical axis, which is embedded into our scene, possesses an opening angle of more than 50○ . If we change the image plane solely by parallel translation, the perspective image is merely enlarged or downscaled. However, if the object is translated orthogonally to the image plane, its relative position to the eye point – and thus also the impression – will be affected. In computer programs which generate interactive perspective images on the monitor, a parallel translation of the image plane is equivalent to “zooming” in or out. Attempts to accomplish a usual enlargement of the image by moving closer to the object lead to new (and increasingly extreme) perspective images. ⊕

• Special and general points It is particularly easy to calculate perspectives of points which lie in π. These are simply the front views of the points. The drawing technique

9.2 Different techniques of perspective

369

Fig. 9.8 Intersection method

required for this situation is the reason why the front edge of the house (through the point A) was assumed to lie in the image plane. Let us now try to depict a general point P at the crown of the roof. In the top view, its projection P c′ can immediately be found. In order to find the front view P c′′ (and thus the perspective image P c ), we have to enlarge the crown up to the point B in the image plane. Its point of intersection B with the image plane lies at the undistorted height of the crown. Thus, the image of the crown can be drawn (BF1 ). P c lies on the ordering line. It is evident that points are ideally “reconstructed” by special straight lines, provided that: Straight lines are defined by the trace point and the vanishing point. ⊕ Remark : It would also be possible to reconstruct P on a so-called depth line perpendicular to the image plane. Depth lines vanish in the principal point H. Thus, P c also lies on P ′′ H. ⊕

370

Photographic image and individual perception

• Trace lines and vanishing lines Since our approach worked so well with straight lines, let us attempt an analogous one with planes. The horizontal base plane γ possesses a trace g in π, which is called the base line. The vanishing line of γ is the horizon h. Let us now consider the vertical plane ε defined by the left wall of the house. It possesses a perpendicular trace e and a parallel vanishing line ecu through F2 . All vanishing points (images of points at infinity) of ε lie on this vanishing line. In the image, the mutually parallel oblique roof edges thus have vanishing points on ecu (compared with Fig. 9.14).

Fig. 9.9 Sunrise and moonset

▸▸▸ Shadow constructions in perspective In perspective, a layman may not notice a substantial difference between parallel lighting and central lighting. Both Sun and Moon are points (or rather, small circular discs) on the firmament from which light rays are emitted. By use of vertical “light planes,” it is possible to determine the shadow of a point P given its top view.

Fig. 9.10 The “sun point” and the not-so-parallel-looking sunlight

⊕ Remark : The additional condition that knowledge about the top view of a point must be given is usually met in architecture. The principle remains the same: Two planar views of a point in space must be known; otherwise, its position is not uniquely determined. A light source, in particular, is only “fixed” once its top view is determined. If the light source is the sun, then its top view – a point at infinity – lies on a perpendicular

9.2 Different techniques of perspective

371

Fig. 9.11 Backlight: parallel lighting on the left, central lighting (flashlight) on the right

Fig. 9.12 Sun point and sun foot in theory and practice

line through the image Lcu of the Sun and on the horizon. L′c u is called the foot of the Sun. If the Sun is visible above the horizon, then its foot lies below Lcu – and backlight occurs. In the case of backlight, the Sun is not visible in the image. It can, however, be determined geometrically (like any other point), and its (theoretical) image lies below the horizon – this simple fact may, however, appear quite unusual to the amateur. In both Fig. 9.13 and Fig. 9.14, the Sun is blocked by the back of the spectator. In the special case of sidelight, the light falls parallel to the image plane, and both sun point and sun foot are points at infinity. All subsequent constructions are also possible by means of continuous parallel translation. ⊕

In Fig. 9.13, the shadow of P on the base plane is determined by connecting the point to the Sun and intersecting the resulting light ray with its top view – the connection of the sun foot with P ′ . The horizontal straight line through P is parallel to the base plane, and its shadow is, thus, also parallel. Therefore it has the same vanishing point as the straight line. The trace of the light plane λ through P in the horizontal base plane is c determined by P ′ and the sun foot L′c u . The vanishing line lu of the light plane through a vertical straight line connects the sun point and the sun foot. In Fig. 9.14, the shadow of a rod P P ′ onto an inclined roof plane is determined. For this purpose, the light plane λ is intersected with the building. The oblique portion of the shadow is part of this intersection figure. In order to verify the result of the construction, it is also possible to intersect

372

Photographic image and individual perception

Fig. 9.13 light planes . . .

Fig. 9.14 . . . and roof planes

the vanishing line of the light plane with the vanishing line of the inclined roof plane. ⊕ Remark : If the Sun were replaced by another (much closer) light source, not much would change in the construction: The only difference would be that the foot of the light source would no longer lie on the horizon. ⊕ ◂◂◂

▸▸▸ Shadow of sidelight and general central projection General central projections with non-vertical image planes are usually much more difficult to construct (see Fig. 9.15). In the image, perpendicular edges pass through a third principal vanishing point F3 , and it is no longer possible to inscribe heights by simply transmitting affine ratios. In such cases, it is helpful to continue assuming that the image plane remains perpendicular when we apply the intersection method. Important points of the object, however, have to be drawn in a tilted manner in the top and front view, which requires one further side view. (More detailed instructions can be found On the website to the book.) However, this example should primarily concern the shadow construction with sidelight. Let P be a point in space with the top view P ′ . This produces c a perpendicular line P c P ′ in the perspective image which possesses the vanishing point F3 . We shall define sidelight as follows: Light should incline in such a way that the shadows of vertical lines on the horizontal base plane appear parallel in the perspective image (Fig. 9.15 on the left). Thus, the sun c foot L′u becomes the vanishing point of the horizontal direction. The light rays can no longer be parallel to the image plane (as it occurred in the special case of the vertical image plane). The sun point Lcu lies “perpendicular” above c the sun foot, which explains why the order line L′u Lu c passes through F3 and is, thus, horizontal. Any point on this horizontal line could serve as the sun point. This reduces the rest of the construction to a simple recipe: The image of the shadow Ps on the base plane can be found by intersecting the c c straight lines P c Lcu and P ′ L′u . ◂◂◂

9.2 Different techniques of perspective

373

Fig. 9.15 The shadows, given sidelight and a tilted image plane, are defined in the following practical way: The shadows of perpendicular edges on the base plane should be parallel to the image plane, and thus, appear parallel in the image. The light rays themselves, as they appear in the image, are not parallel: They have the vanishing point Lcu .

In principle, the intersection method enables us to construct arbitrary scenes, and by adding the aforementioned technique of shadow construction to our toolkit, we could reasonably consider ourselves to be satisfied. Computers calculate perspective images in precisely this way. However, in practice, it may be too cumbersome to “derive” an object’s top and front views every single time, especially as many cases permit a quicker procedure. More instructions can be found in the section concerning perspective sketching from page 624 onwards.

Measuring points The following method is necessary to rectify photographs. Let a photo of a building façade or a photo of a planar landscape be given. The measurements of the various objects are to be determined. Let us first tackle the issue back-to-front. How would we inscribe a planar polygon in a vertical plane ε into the perspective image (Fig. 9.16)? If, by mere coincidence, the plane does not happen to be parallel to the image plane, then the polygon will appear distorted in the image. Considered in space, the image polygon can be constructed by intersecting the “viewing pyramid” through the polygon with the image plane. Both planar sections of the pyramid are collinear images of each other. In the drawing, it is possible to employ a trick which also boils down to the completion of a collineation – though in a manner different from the one described above. If e is the trace of the carrier plane ε, then we can imagine ε rotated about e into the image plane. This causes all points of the plane to become circles of revolution. The rotation, however, can also be replaced by a parallel projection into the direction of the rotation chords. The center of the projection is a point at infinity Du . In three-dimensional space, the polygon in ε and the rotated polygon in the image plane are related via parallel projection (axis e, direction Du of rays) which is displayed in the

374

Photographic image and individual perception

Fig. 9.16 Parallel rotation becomes “recalibration”

perspective image as a perspective collineation. (The original polygon and the rotated copy are congruent!)

Fig. 9.17 Image of a perpendicular line segment and the corresponding collineation

This relation can be understood by looking at a sketch of the situation in space, where it is evident that the point Du at infinity is associated with a vanishing point Duc = Mε on the horizon and at a distance of F2 E. The measurement point Mε can be constructed by rotating E about F2 in a side view. All chords of the rotation vanish at this point of the image, and a planar perspective collineation derives from the relation between the rotated polygon and the polygon in space. The determination of a single pair of associated points allows us to construct images of all other points via a small number of lines. Fig. 9.17 illustrates the most common case, where the carrier plane of the polygon corresponds to the horizontal base plane γ. The measurement point

9.2 Different techniques of perspective

375

Mγ for this plane is found purely planimetrically by drawing the distance d = EH to the principal point. The axis of rotation (= axis of collineation) is the base line g. Both the rotated and the regular top view are related via a parallel perspectivity by way of the parallel rotation chords. This establishes a perspective collineation between the perspective image and the rotated top view (center of collineation Mγ , collineation axis g). ⊕ Remark : The central view P c of a point P at height z which does not lie in the c base plane is located above the central view P ′ of its top view. Let us now consider the point P0 which lies above the rotated top view P ′ 0 at a distance of z (Fig. 9.17). This point can equally be constructed by intersecting the rotation chord through P with the image plane π. Thus, P0 also lies on a collineation ray through Mγ – a conclusion that is by no means trivial! Planimetrically, P0 can also be interpreted as the horizontal view of P (given a distortion ratio of 1 ∶ 1). The horizontal and perspective views are, thus, in a simple relation. ⊕

▸▸▸ Reconstruction from a photo

If the image of a rectangle is visible on the original photo, then the actual shape of any figure in the carrier plane of the rectangle can be reconstructed.

Fig. 9.18 Planar figures with varying levels of distortion (original photos)

The goal is to find the measurement point of the carrier plane. The shape of any planar figure can be deduced from it, even without a ruler. When dealing with original photos (that is, photos that have not been cropped as in Fig. 9.18), we can assume that the principal point is located at the intersection of the diagonals. As soon as the image of a rectangle is provided, the two principal vanishing points F1 and F2 can also been found. The distance circle, on which the measurement point of the plane is located, can be reconstructed using the Thales circle above F1 F2 . ◂◂◂ ▸▸▸ Spatial reconstruction with a given image of a cuboid

376

Photographic image and individual perception

Fig. 9.19 Spatial reconstruction is generally possible when we know the image of a cuboid.

This useful practical case usually concerns a photograph where the horizon h does not pass through the principal point, i.e., where three principal vanishing points F1 , F2 , and F3 with h = F1 F2 exist (Fig. 9.19). The principal point (the orthogonal projection of the center C) is, then, the orthocenter of the triangle F1 F2 F3 . C itself is the intersection point of the three Thales spheres determined by each pair of the principal vanishing points. Again, one can find the measurement point of the base plane on the Thales circle above F1 F2 on the altitude through F3 . ◂◂◂ ▸▸▸ Anamorphoses In the 16th century, Hans Holbein the Younger painted his famous picture “The Ambassadors.” What looks like a shroud on the floor turns out to be a skull – but only if observed from an extreme angle. A figure that is only visible from extreme positions of the observer (such as curved mirrors, as those shown in application p. 227) is called an anamorphosis.

9.2 Different techniques of perspective

377

Fig. 9.20 A morbid detail in the famous picture by Hans Holbein the Younger

It is possible to “implant” such an anamorphosis into a perspective image through a modified measurement point. In the painting, the skull is wellconcealed, since it only becomes visible from a low perspective and after a 45○ rotation of the image. At the National Gallery in London, the picture has been positioned in such a way that the skull becomes visible from the stairway (Fig. 9.20 on the right). ◂◂◂

Fig. 9.21 Anamorphoses: A speed limit sign – the street inscription on the right is not actually a “pure” anamorphosis because the impression of a perspective distortion remains.

⊕ Remark : Fig. 9.21 (Stefan Wirnsperger) illustrates that traffic signs are often anamorphoses. Due to the extremely low angle of observation, letters, numbers, and other symbols used in such signs must often be printed with a certain perspective distortion. Similar challenges arise in the design of billboards on skyscrapers, which people usually observe from far below. ⊕

▸▸▸ Deliberate distortions in computer graphics Perspective images are very frequently employed in computer graphics. One of the elemental tasks of such graphics programs is the so-called clipping procedure: Parts of the scene which lie behind the observer or too close to the front clipping plane (parallel to the image plane through the eye) have to be removed. This may be done through intersection with the viewing pyramid. A fast and thus often employed method consists in applying a spatial collineation to all points in the scene – which turns the eye point into the point at infinity of the principal projection ray. This makes the viewing pyramid

378

Photographic image and individual perception

Fig. 9.22 Two different objects (top and front view) with identical side views

a coordinate cuboid, and thus, greatly enhances the efficiency of clipping algorithms. Fig. 9.22 on the left shows an object after collinear transformation in a top and front view. The view from the left is now equivalent to the perspective image. Now one might maintain that it would be sufficient to inscribe the distance from the image plane above the image points (as illustrated in Fig. 9.22 at the center). Unlike a collineation, however, this transformation would not be linear. The objects are “distorted” accordingly, which leads to needlessly complex algorithms. ◂◂◂

The image of a circle If the planar figure is a circle, then the corresponding image is a conic section, because the projection of the circle from an eye point E generates an oblique quadratic cone. An intersection with the image plane thus produces a conic section (see also Fig. 3.66). It follows from the definition on p. 55 that:

Fig. 9.23 Ellipses and hyperbolas as images of circles

The perspective image of a circle is an ellipse, a hyperbola, or a parabola, depending on whether the circle intersects, does not intersect, or merely touches the vanishing plane.

379

9.2 Different techniques of perspective

πv ∥ π

E

g v = πv ∩ γ

π g =π∩γ

γ e p h

hc pc

ec

eye point E, image plane π, base plane γ vanishing plane πv ∥ π through E yellow circle e does not intersect πv ⇒ image ellipse ec red circle p touches πv ⇒ image parabola pc blue circle h intersects πv ⇒ image hyperbola hc

Fig. 9.24 The position of the circle relative to the vanishing plane πv determines the type of the circle’s perspective image. See also the special case with a perpendicular image plane (Fig. 3.66).

Fig. 9.25 Conic sections as images of circles

Let us consider an elliptical image of a circle together with a circumscribed square of tangents, with two sides parallel to the image plane. The center of the circle is located precisely at the intersection of the square’s diagonals. The square’s image is a trapezoid (straight lines that lie parallel to the image plane possess parallel images). The intersection of the trapezoid diagonals thus yields a point equivalent to the center of the circle – or, the intersection of the images of all diameters of the circle. However, it is not equal to the center of the ellipse appearing as the circle’s image, as can be seen in Fig. 9.24 (yellow circle). ⊕ Remark : If the circle lies in a plane parallel to the image plane, then its image is also a circle. The 10-euro bill contains a perspective image of a bridge which carries circular arcs without any apparent perspective distortion. ⊕

380

Photographic image and individual perception

Circle depictions in ancient times

Fig. 9.26 Two Egyptian reliefs that are more than 3200 years old (Abu Simbel). In principle, we are dealing with front views and “integrated side views”.

It is usually believed that realistic and correct perspective drawings with geometrical context started with the painters of the Renaissance, while the ancient Egyptians “only” used front views and integrated side views in the pictures. (Note the 6-spoke wheel of the chariot in Fig. 9.26 (on the left), which appears undistorted as a circle.)

Fig. 9.27 A 2300-year-old Greek tomb painting (Vergina, central Macedonia). A realistic perspective drawing: The wheel closer to the spectator has been drawn perfectly!

However, we have several examples illustrating that this conjecture is not quite true. One of the most impressive counterexamples is a tomb painting in the grave of Philipp III (the successor of Alexander the Great), drawn around 320 B.C. (Fig. 9.271 ). Not only is the painting impressive as a whole – the wheels of the chariot are drawn almost as if their images were constructed. On the right, a computer-drawn reconstruction of the four-spoke wheels has been superimposed on the original image. Especially the wheel in front is amazingly accurate – a fastidious critic may consider the other wheel to be too small and flat, but that does not diminish the accomplishment of the painter. The four spokes are even “conjugate diameters” of the image ellipse. (In space, they are perpendicular to each other and the tangents in the end points of one diameter are therefore parallel to the other.) 1 http://commons.wikimedia.org/wiki/File:Painting_vergina.jpg

381

9.3 Other perspective images

9.3 Other perspective images Optical illusions

Fig. 9.28 Painting on walls in Pompeii: Perspectives create the illusion of additional space.

Optical illusions seem to be very old. Fig. 9.28 shows two murals in Pompeii (the ancient Roman city was destroyed and buried under ash and pumice following the eruption of Mount Vesuvius in 79 A.D.). One can still see that artists painted columns and other architectural objects on the walls in order to create the illusion of a spatial scenery behind the wall. This provides another example proving that a certain knowledge about perspective drawing had already existed long before the Renaissance.

Fig. 9.29 Relief perspective I

Set decoration employs the term relief perspective, which describes the illusion of a larger space that would never fit on the actual stage. Fig. 9.29 shows a hall of columns that appears realistic, but only if observed from the front.

382

Photographic image and individual perception

It would, indeed, be a fitting backdrop to a dramatic event such as the assassination of Julius Caesar. A spectator in a cheaper seat will, however, recognize that the supposed right angles are not right angles at all.

Fig. 9.30 Relief perspective II

Fig. 9.30 which features a variety of simple geometrical objects (square prisms, pyramids, spheres, and cones) demonstrates to what extent our imagination still accepts an oval as being spherical before noticing a definitive geometric deviation. ▸▸▸ The Gaussian collineation: Virtual 3D images Similar to the already mentioned relief perspective, we have a collineation in optics (Fig. 9.31). When we apply a refraction at a convex lens, there are two rules according to the laws of reflection: Light rays h that go through the center C of the lens are not refracted (h = h∗ ), and light rays s parallel to the optical axis are bundled in the focal point F ∗ behind the lens. The refraction s → s∗ occurs in the principle plane γ ∋ C perpendicular to the axis. A space point P = s ∩ h corresponds to a (virtual) space point P ∗ = s∗ ∩ h∗ .

virtual space behind the lens

Fig. 9.31 collineation in space

real space in front of the lens

According to Gauss, this (reversible) relation P ↔ P ∗ deserves the name collineation, i.e., straight lines g are transformed into straight lines g ∗ . Proof : We consider g to be the intersection of a plane ε1 parallel to the axis and the connection plane ε2 = gC with the center. The first plane is transformed into a plane ε∗1 through F ∗ and the intersection line ε1 ∩ γ, whereas ε2 = ε∗2 remains unchanged. Thus, g ∗ is the straight intersection of two planes. ⊙

9.3 Other perspective images

383

Planes ϕ ∥ γ are transformed into planes ϕ∗ ∥ γ. It is useful to know this when it comes to photography. Therefore, we will come back to the Gaussian collineation and its consequences in our geometry-based photography course (Appendix B). ◂◂◂ ▸▸▸ Two different sequences

Fig. 9.32 Real and pseudo-perspectives

Fig. 9.32 shows two arrays of Buddha statues. On the left, all figures are of equal size, and it is possible to move freely in their vicinity. The statues on the right, however, were stacked parallel. They can only be seen from a single position near the cave entrance. The figures become gradually smaller and smaller, which is barely noticeable due to the lighting effects, and this makes the cave appear deeper than it is. ◂◂◂ ▸▸▸ Geoglyphs in the desert sand Members of the pre-Columbian Nazca culture (300 B.C. to 600 A.D.) in the southern Peruvian coastal valleys used to decorate their pottery and embroideries with stylized animal motifs. They are best known for scraping gargantuan animal depictions, which often span many hundreds of meters, into the dry desert ground. These images can only be seen in their entirety from an airplane (Fig. 9.33 on the right) and even appear perfectly symmetric from certain angles – a masterly accomplishment, which also led to far-fetched speculations. Some, for instance, have claimed that the Nazca people must have employed hot-air balloons! It is noteworthy that the giant animal figures do not appear to be symmetric from straight above. Instead, they seem to exhibit perspective distortions as in a photograph shot from a high angle (or a photograph from a low angle – see Fig. 9.33 on the left). Quite paradoxically, this leads to a semblance of symmetry, but only from certain positions, which some commercial airplanes luckily cross on their flight path. Without any claim to truth, one may imagine the following story – inspired by projective geometry – of how these figures came about:

384

Photographic image and individual perception

Fig. 9.33 In principle, these are planar figures.

Somebody – let us say a high priest – stands on a h = 15 meters tall wooden tower (apex Z, top view Z ′ , Fig. 9.34 on the left) holding the symmetric drawing of an animal. He then directs his subjects to lay stone blocks in a way that would look symmetric and consistent with the image from his point of view. Ideally, the subordinates work at some distance from the tower so that the priest can overlook the whole construction site without needing the ability of “panoramic view”. This procedure would make the animal motif appear symmetric from the skewed high-angle perspective of the tower but distorted from a vertical top view. Now let us discuss the enlargement of the image: A rope is stretched from Z0 = Z ′ to one of the many contour rocks P and the rope length P Z0 is applied multiple times in the course of the enlargement process (e.g., k = 3 times as in Fig. 9.34, or at even larger scales). This must involve at least two people: One person at the center directs the other at the end of the rope, which ensures the straightness of the ray P Z0 . At the end of the enlarged distance, the point P ∗ is marked with another rock.

Fig. 9.34 It could have been like this.

This technique makes it possible to construct an enormous contour in a relatively short period of time. As with the real Nazca lines, the image would appear prospectively distorted in the top view and symmetric from a tower

385

9.3 Other perspective images

that has been scaled accordingly (height k ⋅ h meters, in our case 3 ⋅ 15 = 45 meters)! It can further be concluded that the scaling center Z0 does not necessarily have to be the top view Z ′ of the tower apex. In the general case, the point from which the image appears to be symmetric does not lie directly above the tower apex but in the elongation of the segment Z0 Z scaled with factor k. A further remark that might enhance the plausibility of the above speculations: It would, of course, be possible to enlarge a smaller motif – perhaps only a few meters in diameter – using the “rope method.” However, the scaling factor would have to increase, which would, in turn, lead to greater errors and imprecisions. Besides, why would the Nazcas create perspectively distorted, non-symmetric images on a very large scale if their original images ◂◂◂ (hummingbirds, spiders, etc.) were perfectly symmetric? ▸▸▸ Baroque illusions In the 17th century, it used to be the fashion to paint ceilings in such a way that a spectator looking up from the center of the room would have the illusion of a much bigger space.

Fig. 9.35 Pozzo at work

In order to produce a correct planar painting, a plane (such as the ceiling of a room) must be painted with a perspective image that, from a chosen point of view, creates the illusion of great spatial depth, “with all the bells and whistles” that might be found in this imaginary space (clouds, columns, etc.). Andrea Pozzo was a true master of this genre. He was even capable of correctly painting barrel-shaped interiors, using a special technique (Fig. 9.35) to accomplish this goal: He first constructed a planar “auxiliary ceiling” which

386

Photographic image and individual perception

Fig. 9.36 Andrea Pozzo’s ceiling paintings and his projection onto a horizontal ceiling plane

consisted of a square net of tight strings. He then projected this net onto the curved interior by placing a candle in the spectator’s position. By tracing the shadow lines cast by the candlelight on the curved surface, he got a “reference net” into which he interpolated the perspective image for his painting. (The illustrations are by Stefan Wirnsperger.) The inverse of the procedure would be the following: Consider the pattern of straight lines and the orthogonally intersecting half-circles on the cylindrical ceiling. If this curved net is then projected into the virtual ceiling plane, it would generate a net of parallel straight lines and ellipses. The latter are derived as the section curves of the plane with the projection cones of the circles, which are oblique circular cones. In order to get the same impression of a curved painting from the projection center as in Fig. 9.36 on the left, one might choose to observe a distorted painting (as in Fig. 9.36 on the right) on a planar ceiling. ◂◂◂ ▸▸▸ Dynamic Sphere – the illusion of a sphere Who would not want to be under a dome with plants climbing up its sides (Fig. 9.37) and just relax on a sofa to enjoy the atmosphere? Would this be possible if we only had a room with a flat, low ceiling? An optical illusion might do the trick. Solution: Ruth Schnell took it upon herself to create such an optical illusion. The walls of a room with 250 m2 (Fig. 9.38 shows a computer model created by Franz Gruber) were covered in extremely thin foil (23-karat leaf gold, ca. 100 m2 of gilded surface, grey paint) so that, at least upon entering the room, you would get the perfect illusion: You would, in fact, see a scene like the one represented in Fig. 9.37. Fig. 9.38 shows how the foil cut-out (Fig. 9.39) was pasted onto the ceiling. A very precise calculation of the extremely distorted projection was possible with a computer, by projecting a virtual model of the room from a given

9.3 Other perspective images

387

Fig. 9.37 A semi-spherical dome with vines

Fig. 9.38 Virtual room model including the necessarily distorted leaf pattern

centre onto the flat ceiling at a very oblique angle. Fig. 9.39 on the right shows a detail of the cut-out. How does this effect look in reality (The Ritz Carlton in Vienna, Fig. 9.40)? The illusion is, in fact, perfect when we enter the room. Once you start moving inside the room, you get the impression that you are surrounded by ◂◂◂ dynamic plant patterns. ▸▸▸ We are only measuring angles! The following idea was conceived by Franz Gruber: Let us imagine ourselves sitting in a lecture hall, looking at images cast onto the screen by a projector. In such cases, it is advisable to avoid sitting at the sides. Under ideal conditions, we would want to sit near the projecting apparatus (Fig. 9.41), since this would enable us to see the pictures as they were taken. Let us now imagine that a prankster pulls on a rope, opening a trap door on the ceiling which causes paper snippets to rain from above – and straight into the light cone. Spectators on the sides would no longer be able to discern

388

Photographic image and individual perception

Fig. 9.39 This is what the gold foil cut-out looks like! Right: Enlarged detail.

Fig. 9.40 This is the reality: perfect illusion upon entering the room (left, center), dynamic plant patterns when we walk around the room.

much of the projected image. Spectators near the projector, however, would barely notice a thing! What actually happens is a perfect illusion: The paper snippets are illuminated by the projector as soon as they enter the light cone. A small part of the original image is projected onto each snippet at varying levels of distortion. The view is further distorted by shadows of the snippets appearing on the projection screen. However, seen from the lens center the projected image remains coherent, since only angles can be measured and the medium onto which the projection takes place is unimportant. ◂◂◂

Fig. 9.41 A dia projection seen from two different viewpoints . . .

9.3 Other perspective images

389

Fig. 9.42 . . . suddenly disturbed by a shower of paper snippets

▸▸▸ Star signs (Fig. 9.43) To find the North Star, one must first discover Ursa Major (the Big Dipper) in the night sky. The North Star is located approximately at the five-fold elongation of the first stars in the constellation.

Fig. 9.43 The striking constellation of Ursa Major

The spatial constellation of the stars is indiscernible to the naked eye, since the stars may vary in luminosity and in their position on the projection rays. Due to the enormous distances involved, we also fail to notice a difference when observing the constellation over a half-year interval (and thus at a distance of 300 million kilometers). ◂◂◂ ▸▸▸ The spider on the sphere How can you determine what a spider is “interested” in or in which direction it wants to run? By placing the spider on a free moving spherical surface and then rolling this computer-controlled ball in such a way that the spider always ends up running “on the spot”. Let us now turn to the geometrical part: We would like to deceive the animal by projecting images of a natural environment onto a cylinder of revolution. These images change in synchrony with the direction of the spider’s movements (as well as its velocity). What do we have to consider when we set up this projection? Solution: The apparatus for this projection (Fig. 9.44) was designed at the University

390

Photographic image and individual perception

Fig. 9.44 Left: Different computer-modelled projections on the inside of a cylinder of revolution. Right: The spider (or any other viewer in this position) sees the curved squares as variously sized “entrances” for hiding.

of Vienna (Department of Neurobiology2 ). The projection is generated by four projectors, which, for reasons of space, are positioned outside of the cylinder. The almost point-shaped light sources emit – due to the edges of the image – rectangular light pyramids. If we intersect the side surfaces of the pyramids with the cylinder of revolution, we get ellipses. The “rectangular” illuminated field on the cylinder thus has elliptical edges. The neighboring illuminated fields overlap (Fig. 9.44 left) – an additional complication that must be taken into account in the calculation of the images. Several square-grid fields lying in one plane shall now be shown to the spider. The position E of the spider’s eyes (a spider has eight lens eyes, see Fig. 9.45) is more or less constant. If the vertical fields of the grid are projected onto the cylinder, the images remain straight and vertical. Together with E the horizontal fields of the grid form projection planes that intersect the cylinder along ellipses. Squares of the grid that are farther away appear smaller in the projection – that is, the angles of vision α and β (Fig. 9.44 right) to the vertical, as well as horizontal, square sides change. If the spider wants to run towards the nearest black square (= hiding place), it will automatically aim at the square that appears to be the largest. The more closely meshed grids that can be seen in the image emanate from flat – and, naturally, virtual – square grids that lie farther away. The cylindrical images must still be recalculated onto the projection plane of the projectors. The elliptical edges are traced back on quadratic cones through the light centre to the image that is to be projected. So, on this image, the edges also appear as ellipses. This results in double exposures, 2 Research

project funded by the Austrian Science Fund (FWF; PI Axel Schmid) in collaboration with the Austrian Center for Research on Virtual Reality and Visualization VRVis (Anton Fuhrmann).

9.3 Other perspective images

391

Fig. 9.45 Eyes of a wolf spider (tarantula). You can clearly see eight well-developed lens eyes, which are mainly located towards the front and are remarkably efficient for spiders, which usually rely on their tactile sense. The blue of its eyes is an interference color that is the result of repeated reflections and refractions in the multi-layered reflective tissue (tapetum lucidum).

which can be “airbrushed” by making the corresponding image points (pixels) darker. Additional challenges lie in solving the remaining problems (how to control the ball) and “fine tuning”. ◂◂◂ The silhouette of a sphere

Fig. 9.46 Dew in a spiderweb: Spheres always look the same, no matter how big or small they are. In this case, even the biggest spheres have a diameter of less than 1/2 mm.

In nature, spheres are “produced” in two completely different ways: Firstly, tiny spheres like water droplets are formed by surface tension (Fig. 9.46).

392

Photographic image and individual perception

Secondly, the big spheres in the universe (starting with a diameter of more than 500 km) are formed by gravitation (Fig. 9.47). ▸▸▸ Hyperbolas as silhouettes of spheres?

Fig. 9.47 When looking at big spheres, like planets, their contours may appear as parts of hyperbolas. To the right: Extreme wide-angle simulation.

From the photographer’s point of view, it is impossible to depict tiny spheres like the ones shown in Fig. 9.46 in such a way that the outlines are not ellipses (or circles, if we look at the sphere’s center), because a sphere that has a hyperbola as its outline would have to intersect the vanishing plane through the center of the lens, and therefore, it is simply too small (Fig. 9.48, however, shows that – if you try hard enough – it can be possible).

Fig. 9.48 In these extreme wide-angle photographs with short distances, it was possible to capture the silhouette of a sphere as part of a hyperbola. The photo in the middle shows a closeup of the street lamp in the image on the right side.

From a space shuttle or similar vehicle, however, it is very easy to see that the planet that is being circled by the shuttle intersects the vanishing plane, e.g., if one focuses on something like the Moon on the horizon (Fig. 9.47). In the picture itself, it is usually very hard to determine what kind of conic we are dealing with. We could say: If it is obvious that the planet is partly behind the camera, the conic must have “the DNA of a hyperbola”. The limiting case, namely the parabola, is practically not achievable: For this, the big sphere would have to touch the tilted camera’s vanishing plane. It seems easy to answer the question whether one can see the curvature of the Earth from an aircraft or not in the affirmative, if we look at the photo on

9.3 Other perspective images

393

Fig. 9.49 Does one see the curvature of the Earth from an aircraft?

the left-hand side of Fig. 9.49. However, this could also be a lens error (and it probably even is to a certain degree): Not particularly expensive wide-angle lenses tend to create slightly bent curved lines as images of straight lines – except that the straight line is “radial”, i.e., it intersects the optical axis. A good test is to rotate the camera in such a way that the end points of the alleged curves go through opposite diagonal points of the frame. If the image of the horizon is still curved, we can be sure that our answer is correct. (In Fig. 9.49 on the right, the horizon is considerably less curved than in the one on the left.) ◂◂◂ ▸▸▸ When silhouettes of spheres are always circles In central projections, the silhouette of a sphere is always a conic, namely the intersections of a cone of revolution (the tangential cone from the center C to the sphere Σ with the image plane π (Fig. 9.50)). The only “problem” with that is that humans expect circles as silhouettes, because if they take a look at a sphere, they look directly towards the estimated center of the sphere. There is an additional reason for the circular boundary: Our eyeballs are spherical and not flat. The retina is doubly curved. In fact, if the center of the central projection is the center of a surrounding sphere K (which is not exactly the case, however), then the intersection of the projection cone would exactly be a circle. A mathematician will immediately try to project the spherical image on the retina stereographically onto a plane π. This special projection preserves circles and, again, we have circular boundaries of spheres. As shown in Fig. 9.50: In a central projection (C, π), spheres Σ usually have elliptical contours sc . Projected onto a sphere K around C, the countour will always be a circle cκ . In a stereographic projection onto a plane (center S, π), the contours will again be circles cs . ◂◂◂ ▸▸▸ “Smoothing” undesirably extreme perspective images We already know that it does not matter onto which surface an image is

394

Σ1

Photographic image and individual perception

c1 K cc1 C Σ2

c2

S cc 2

cκ2

cs2 cκ1

cs1 π

π Fig. 9.50 Contours of spheres in central projection are always conic sections. The projection of spheres on a sphere around the projection center always leads to circular outlines, and finally, those circles can undergo a circle-preserving stereographic projection.

Fig. 9.51 A cropped fish-eye-lens picture. In the original photograph, the horizon lies above the center of the image. It is, therefore, curved downwards, though not a hyperbola.

projected, if only the spectator is forced into the “right” position. Certain circumstances may, therefore, necessitate the production of extreme perspective images. If a photographer standing in a small room tries to capture as much of that space as possible, an extreme wide-angle lens is usually employed. The result might look like Fig. 9.52 on the left. If such a photograph is then projected onto a wall, and if a spectator is forced into the same relative position as the photographer at the time the picture was taken, the optical impression will be realistic. A similar problem arises during outdoor photography when a large object is supposed to be fully contained by a photograph from a short distance (Fig. 9.52 on the right). This, too, calls for an extreme perspective image. If such a photo were then projected, it would appear “normally distorted” from the perspective of a spectator sitting close to the projection screen. At larger distances, the image’s unnatural appearance would become noticeable.

9.3 Other perspective images

395

Fig. 9.52 Extreme perspective images

Image on a sphere The question arises whether a compromise exists that would allow the entire object to be “contained within the frame” while still allowing the image to appear natural from greater distances. Curiously, the answer is both yes and no. We would have to squeeze the “outliers” at the image edges into the picture by curving the image surface. This comes at the cost of linearity (straight line preservation)! In the case of the human eye, the image is projected on a spherical image surface. It, thus, makes sense to project the image onto a sphere. For the sake of simplicity, we shall project from the midpoint of the spherically curved surface, which may not correspond exactly to the projection in our eye, but it is equivalent to the “stitching together” of many small images during the “scanning” of a room. The eyeball constantly rotates about its center, and the many partial images are combined into a whole image inside our brain. After the projection of the room from the center of the sphere to a spherical surface, we are faced with the next question: How do we save this image in order to show it to the spectators? Either of the following solutions may be technically feasible: The photo sensors on the electronic chip may certainly be arranged on a sphere, just as an approximately spherical projection screen may be produced. In both cases, however, the practical realization may be quite costly. ⊕ Remark : As we have discovered numerous times before, the surface of a sphere cannot be developed into the plane without distortions. There are, however, two methods – among many others – which accomplish this task particularly well for our purposes. One of these methods is the stereographic projection of the sphere surface (with center M ) from a point Z on the sphere to a plane orthogonal to the radius M Z. Such a projection has the great advantage that sphere circumferences remain circular in the projection (Fig. 9.54 on the left). The projection cone around the sphere is a cone of revolution with the apex M , touching the sphere at a circle. Since stereographic projection preserves circles, contours of the sphere remain circular after the projection. Straight edges in space are first represented by circular arcs on the

396

Photographic image and individual perception

Fig. 9.53 Stereographic projections

sphere and then as circular arcs in the image plane. Fig. 9.53 illustrates how this technique can be used to “smooth” extreme perspective images.

Fig. 9.54 Extreme views of spheres

The other method was propagated by Guido Hauck around 1900: It uses the already mentioned cylindrical projection of the sphere, where the spherical coordinates (latitude and longitude) are taken as planar Cartesian coordinates. Fig. 9.54, right shows how the silhouettes of a sphere are distorted into irregular ovals by this method.

Fig. 9.55 Hauck’s perspective

Given a horizontal optical axis (Fig. 9.55 on the left), Hauck ’s method is well-suited for the transformation of extreme perspectives: Vertical edges remain vertical and straight in the projected image. All other straight edges appear to be curved, though

9.3 Other perspective images

397

not in the form of circular arcs. In general views of objects, the edges may even be projected as curves with inflection points (Fig. 9.55 on the right). ⊕ ◂◂◂

▸▸▸ The geometry of the fish eye

Fig. 9.56 What does a fish see?

The aforementioned methods for the smoothing of extreme perspectives are mostly applied in computer graphics. There exists a further practical solution to this problem: the use of a fisheye lens. This name makes sense when considering Fig. 9.58: When we look out of water with a calm, flat surface, we can see everything above the water surface. The image of the outside world is centered in a circle. Objects which are close to the water surface appear downscaled and flattened towards the edge of the circle.

Fig. 9.57 Another view from the water

This kind of geometry on the water surface will be discussed in the next section. Fig. 9.58 shows an exception in the animal kingdom: the four-eyed fish. Its eyes are split in two, which enables it to see undistorted images above and below water.

398

Photographic image and individual perception

Fig. 9.58 A very strange fish eye

Fisheye lenses are often employed in door viewers. When one looks through them, the objects outside are pressed inwards – an effect which is achieved in photography by using fisheye lenses. Standard photographic lenses are flat by comparison and symmetric with respect to a plane. The fisheye lens, on the other hand, is spherically curved to a large degree and is, therefore, capable of capturing “eccentric points” – the points whose angle between their connection to the lens center and the optical axis may be up to 90○ . Compared to a flat lens, light rays have a smaller angle of incidence with respect to the surface normal, which leads to lower degrees of refraction. Furthermore, due to the inclination of the optical axis, the image points of eccentric points in space are pressed inwards into the image.

Fig. 9.59 On the left: circular ornament, on the right: concentric rainbow

Circles are usually pictured as non-elliptical ovals. Circles whose axes coincide with the optical axes of the lens remain circular, because both the circles and the lens are rotationally symmetric with respect to the optical axis. Fig. 9.59 serves to illustrate this principle. In the left image, a circular ornament was photographed “at ankle level.” In the right image, two (!) rainbows are visible upon closer inspection. When the Sun is very low in the sky, the axis of any rainbow (or, in this case, of both rainbows) is almost horizontal. The primary and secondary rainbows [9], thus, appear to be nearly circular.

9.3 Other perspective images

399

Straight lines are usually pictured very distortedly while the angles that they enclose are spared the extreme distortion of traditional perspective images (Fig. 9.52). ◂◂◂ Straight lines g which intersect the optical axis have their images in the projecting plane that is defined by g and the optical axis. With respect to the image, it can, therefore, be said that the closer a straight line comes to the lens center, the less distorted it appears. In practice, this becomes relevant when taking pictures of scenes with distinct horizons (such as Fig. 9.60 on the left). Due to the rotational symmetry of the lens, this principle also works for non-horizontal straight lines (Fig. 9.61). The center image of Fig. 9.60 shows that this knowledge can be employed to alter fisheye photos in deliberate ways: A relatively small translation of the principal point causes the boards of the patio to become distorted – in one case, in the frontal area; in the other case, in a ray-like formation. What makes fisheye photos especially fascinating is the near-infinite depth of field: Both the sunflower and the mallow blossom almost touch the lens in these shots. This property is also explicable in geometric terms: The smaller the focal length, the more distantly the objects are positioned (measured in focal lengths). We know from far-away objects that their image points are very close to the light sensitive layer of the camera sensor.

Fig. 9.60 Diagonals remain straight (I)

Any regular photograph (points P c ) can be converted into a fisheye image (points P f ) – and vice versa: Any fisheye photo can be transformed into a regular perspective image. The associated points P c and P f lie on rays through the principal point H. The distances HP c and HP f are connected by a mathematical relation which does not depend on the polar angle of the ray. The law of refraction allows us to calculate several “support points” of the relation and derive further intermediate points by interpolation. Finally, let us weigh the advantages and disadvantages of the fisheye lens. The one great disadvantage is the “distortion” of general straight lines. After half a millennium of “classical perspective,” this visual feature is very unusual to our eyes. Yet, to be fair: The fish eye would have to be compared to an

400

Photographic image and individual perception

Fig. 9.61 Diagonals remain straight (II)

ultra-wide-angle lens, and the images produced with such a lens are equally unusual. This disadvantage can be mitigated to some degree by using the lens in a specific way: Straight lines which pass through the principal point remain straight, just as circles parallel to the image plane remain circular. The advantage of a fisheye lens lies in its capacity for photographing scenes from extreme perspectives which would otherwise be “impossible to capture.” Fig. 9.62 on the right illustrates this very point: The inside of a cockpit can only be wholly captured by a fisheye lens. In this particular case, the image does not even seem to be very unnatural, because the original scene is not dominated by long straight lines. The human head is also largely undistorted in the photograph. The affine stretching of the circular image into an ellipse even enhances the “landscape effect” of the image.

Fig. 9.62 Anything is possible!

Fig. 9.62 on the left demonstrates a further advantage: The toes in the image appear so large because they were only two centimeters away from the lens – the remainder of the scene (at the edges in particular) is downscaled, which neatly harmonizes with the extreme magnification. What is particularly noticeable, however, is the enormous depth of field offered by the lens. This, in turn, is an effect of the very small focal length [9].

9.4 Geometry at the water surface

401

9.4 Geometry at the water surface In this section, we deal with the physical and optical peculiarities at the boundary surface between air and water (the latter being optically denser). In particular, we shall consider the reflections at the top and bottom sides of the division plane, as well as the refraction towards or from the normal of the boundary surface, depending on the medium that one inhabits. The refraction towards the normal happens in the optically denser medium. Knowing a point of the light ray and another point of the refracted light ray, we calculate the refraction point by solving a degree-four algebraic equation. In this particular context, its solution is always unambiguous. When looking through the water surface, a plane can never be seen in an edge view. Furthermore, a general object inside the water cannot be precisely reconstructed, no matter how many pictures of it are taken from outside the water.

Adapted eyes

Fig. 9.63 Adapted eyes

⊕ Remark : Water is our elixir of life – it is almost universally beloved among our own species and among many of our mammalian relatives (Fig. 9.63 on the left and right). Animals which frequently alternate between land and aquatic life often possess specially adapted dichotomous eyes, such as the 5 mm long whirligig beetle in Fig. 9.63 (at the center) or the four-eyed fish in Fig. 9.58. The seal (Fig. 9.63 on the right) is capable of changing the focal length of its eye lens by muscle contraction, though it tends to be rather short-sighted on land (see also application p. 409). For the same purpose, some reptiles have a transparent or translucent eyelid that is drawn over the eye when they descend below the water surface. Crustaceans possess telescopic compound eyes, which apparently enable them to see rather well above water. There are some small animal species that can run across the water surface without sinking, such as the predacious water strider in Fig. 9.64 on the right or the wolf spider (not a water spider!), pictured with its egg cocoon in Fig. 9.65 at the center. Other animals, such as the Nepomorpha in Fig. 9.64 on the left, can even move on the bottom side of the water surface! Like all small objects, small creatures do not immediately sink into the water because their body surface, or contact surface, is relatively large compared to their

402

Photographic image and individual perception

Fig. 9.64 Danger from above and below

Fig. 9.65 Surface tension can carry a number of objects or animals, as long as they are small enough.

weight. If an object is k times smaller than a similar one of regular size, its surface is k times larger compared to its weight. (This relation has very important consequences in nature and can easily be proven with the example of a cube.) This is why a sufficiently small coin (Fig. 9.65 on the left) will float on the water surface under ideal conditions. In large creatures, the pressure exerted on the water surface is greater than the counteracting water pressure. ⊕

Reflection at the surface

Flatly incoming light rays (Fig. 9.66) are almost completely reflected by water, whereas total internal reflections occur underwater (Fig. 9.68). As we shall soon see, this is only the case up to a certain well-defined threshold angle of incidence. The total internal reflections in Fig. 9.70 show the tiles on a vertical wall or the floor of a basin. The right image shows the reflection of both types of tiles, as well as the abrupt ending of the total internal reflection at the threshold angle.

The Snell-Descartes law of refraction The speed of light is 299 792 458 meters per second but only in vacuum. In the air, this speed is a little bit smaller, whereas in water, it is only about 75 percent of the original velocity. The ratio n of these speeds is called the refractive index. When ordinary (visible) light hits water, this index is about

9.4 Geometry at the water surface

403

Fig. 9.66 Perfect mirror from above (flat viewing angle)

Fig. 9.67 Partial reflection (steeper viewing angle)

4 ∶ 3. Different light components (such as the colors of the rainbow) have slightly different indices. The wave structure of light plausibly explains the refraction of light rays (the wavefront tilts upon hitting the separating layer). Snellius’s law of refraction can immediately be derived from Fig. 9.69 by BC1 v1 BC1 AC2 = =n⇒ =n⋅ ⇒ sin α1 ∶ sin α2 = n. AC2 v2 AB AB If we are underwater and wish to calculate the threshold angle for the total internal reflection, we only need to determine the inverse of the refractive index. Apparently, Snellius’s equation does not always provide real solutions

Fig. 9.68 Perfect mirror from below

404

Photographic image and individual perception

Fig. 9.69 The wavefront explains the law of refraction.

for the exit angle. A total internal reflection occurs starting at the limiting case sin β = 1/n = 3/4 ⇒ β ≈ 48○ .

From then on, the water surface acts like a perfect mirror, and because the threshold angle is slightly different for different wavelengths, a rainbow effect can be seen at the transition area (Fig. 9.57).

Fig. 9.70 Image raising from above and below

Who is looking towards the left in Fig. 9.56? The answer is not trivial at all. Fish A sees fish C both directly and as a reflection and fish B only directly, including its tail fin as a reflection outside of the cone Γ’s base circle with the critical opening angle of 2 ⋅ β. The cone Γ may be called the limiting cone if seen from the perspective of A.

Image raising The so-called effect of image raising causes confusion when we look into the water. The flatter the viewing angle, the more pronounced these effects become. Fig. 9.70 shows an extreme example. The upper crocodile (which does not actually exist) is flatter than the lower one – which, in turn, is not exactly where it appears to be.

9.4 Geometry at the water surface

405

Fig. 9.71 Image raising at the swimming pool

Fig. 9.71 shows a pool of constant depth, though one constantly has the impression of standing next to the deepest spot. The distortion effects appear at their most extreme if one moves sufficiently close to the water surface. Projecting planes

Fig. 9.72 Can a plane be turned into a projecting plane through refraction?

In Fig. 9.72 on the left as well as in Fig. 9.72 on the right, the following question seems to arise: Is it possible to see planes through the water surface in an edge view? Fig. 9.72 at the center illustrates that the points of a surface are always distributed on a polygon (which, in the general case, is not convex). Only the planes which contain the normal to the water surface through the eye point appear as straight lines.

Fig. 9.73 “Folding” of a plane into a ruled surface

Fig. 9.73 on the left shows two ruled surfaces appearing as straight lines from the position of the eye. They are generated by straight lines which correspond to the pencil of rays through the straight line in the division plane after the refraction. From an algebraic point of view, the symmetric parts of the surface

406

Photographic image and individual perception

also belong to it. The viewing rays emanating from the eye point E belong, after refraction, to the normal congruence of an ellipsoid of revolution or a hyperboloid of revolution (Fig. 9.73 on the right). The focal surface of the congruence is created by a rotation of the respective focal lines (diacaustics). ▸▸▸ Reconstruction with two eyes underwater Fig. 9.74 in the top left shows how a point S in space can be perceived at another, well-defined position – at least in the case of planes which are normal to the surface and which also contain both eye points. By moving both eye points closer to each other at the transition (Fig. 9.74 bottom left), the intersection point of the refracted rays moves towards a point on the focal line that does not lie on a normal through S to the water surface. If S moves at a constant water depth, then a locus curve whose deepest point is between the eyes (or, in the limiting case, below the eye) is traced. This explains the illusion of always standing above the deepest point of the pool (Fig. 9.71).

Fig. 9.74 Reconstruction of an object underwater

Of course, the point S in the water does not generally lie in the main normal plane through both eye points. According to the law of refraction, the refracted light rays lie in planes normal to the water surface, and thus, intersect on the normal m through S. On the other hand, the refracted rays coincide with m at various points (unless the eye points are equidistant from m). This means that the elongations of viewing rays cannot intersect in the points of refraction, and therefore, it is not possible to reconstruct a point S in space precisely, no matter how many photographs are given. The error increases with the distance of S to the main normal plane. ◂◂◂

Submerged As a camera is submerged into the water (like in Fig. 9.75), the photographer is faced with particularly strong refractions, which abruptly disappear as soon as the camera is wholly submerged and we thus return to regular perspectives – though the objects now appear enlarged by the factor 4/3. This leads us to

9.4 Geometry at the water surface

407

Fig. 9.75 The transitional layer and the world below

greatly overestimate the mass of underwater objects, which increases linearly with the cube of an object’s length (see Fig. 9.76).

Fig. 9.76 Simultaneous vision above and below water

Refraction at curved (spherical) transitional layers We shall now discuss the creation of a rainbow as an example of refraction in a curved water surface (Fig. 9.77). The primary rainbow is produced by a refraction towards the normal of the transition surface, a one-time total internal reflection, and a final refraction away from the normal of the transition surface (Fig. 9.77 center) – all due to the presence of water droplets in the atmosphere after a downpour. The total internal reflection at the back side of the droplets only occurs for light rays which strike the droplets at a flat angle. An exit angle of about 42○ produces a maximum scattering into spectral colors. Blue wavelengths are refracted the most strongly, while red wavelengths experience the least refraction. This causes red colors to appear at the outer edges.

Fig. 9.77 Rise of a rainbow

408

Photographic image and individual perception

A rainbow is not actually a circle but a cone of revolution which appears as projecting to the observer and which possesses half an opening angle of about 42○ . Driving into the foot of the rainbow is, thus, actually possible, but only at sunset, on a wet road producing a fine drizzle and at a 42○ angle to the shadow direction.

Fig. 9.78 Daily illusions

⊕ Remark : Part of the light which bounces about inside the droplets will only exit after a double reflection, producing a secondary rainbow with its red strip on the inside that is very faintly visible at 51○ (Fig. 9.77 on the left). The spectral colors’ varying indices of refraction cause a scattering of sunlight at flat angles of incidence. The more energy-rich components (blue, green) are so strongly scattered by the atmosphere that they do not even reach the observer. Due to the curvature of the light rays, the red Sun remains visible on the horizon up to several minutes after it should have already disappeared (Fig. 9.78). ⊕

Fig. 9.79 Mirages

Fig. 9.80 Water in the desert?

9.4 Geometry at the water surface

409

⊕ Remark : Mirages also result from continuous light refraction (as in Fig. 9.79 and Fig. 9.80). The hot layers of air close to the desert surface or paved road are optically less dense. Light rays which would otherwise reach the ground are refracted away from the perpendicular and reach the spectator via a detour. The spectator thus notices an apparent reflection in the elongation of the curve tangent. ⊕

▸▸▸ The optical system of our eyes The human eye is a highly interesting optical device. Light rays are first refracted at the cornea, proceed into the “area” of the intraocular fluids, and then only have to move through the inner lens before finally lighting the retina. First of all: Calibrating sharpness is only possible within a very small deviation from the optical axis, though a greater viewing cone is automatically captured by “scanning” (eye-rolling).

Fig. 9.81 Focusing and adaptation using the lens

In 1911, the Swedish ophthalmologist Allvar Gullstrand received the Nobel Prize for Medicine for his precise model of the optical rules that determine image construction in the eye – a model that is still used today and specifies curvature radii (including the indices of refraction) for all optical media that are involved. As mentioned in the application p. 278, the light rays undergo their greatest refraction at the cornea. Fig. 9.81 shows a computer simulation based on standard values. Light rays which are parallel to the axis are precisely focused on the retina in several steps. A point on the axis (center image) near the cornea first appears very blurry. Adaptation quickly changes the curvature radii of the lens via muscle contraction, though as close an object as the one pictured in the right simulation image can only be sharply seen by children and very short-sighted adults. ◂◂◂ ▸▸▸ How does insect vision work? According to the rules of geometry, three-dimensional vision – or rather the ability to estimate depth values – generally requires two separate images of the spatial situation.

410

Photographic image and individual perception

Fig. 9.82 Fixed insect eyes produce curved perspectives.

It is sometimes stated that the simultaneous vision with two eyes and the subsequent reconstruction of a three-dimensional model from the images require exceptional brain power, of which an insect would simply not be capable. The logical conclusion would be that insects do not possess spatial vision. Human vision can only partially be compared to the vision of a compound eye. The eyeball of “higher animals” moves almost spherically – it rotates with two degrees of freedom. If we, as humans, fixate upon a not-too-distant point, we direct the optical axes of both eyes towards it and then “calculate” the distance of the point from the angle of the intersecting axes.

Fig. 9.83 An eye excellently adapted for spatial vision

An insect eye is “fixed.” A point in a shared field of vision is observed by exactly one facet (ommatidium) of the left and right eye respectively (Fig. 9.84). If, however, a point is visible by the facet x of the left eye and the facet y of the right eye, then its spatial position can be determined – so to speak – “in hardware”. No further measurement of angles or reverse calculation of distances is required!

9.4 Geometry at the water surface

411

Fig. 9.84 The optical axes of the ommatidia intersect at fixed points.

If, for instance, an insect has 1000 facets (ommatidia) in each compound eye, and if 200 of them share the same field of vision in each respective eye, then there are thousands of such fixed positions that the insect may be able to interpret without even “thinking about it” – just as the predefined joints and the rigid chitin exoskeleton allow for several thousand leg positions which the insect probably does not “think about” either.

Fig. 9.85 Insects are not the only ones good at judging distances.

⊕ Remark : Jumping spiders (Fig. 9.83 on the right) possess multiple pairs of eyes which enable them to see excellently – and even in color. Naturally, only a distance area of a few centimeters can be important to such a small an animal. Fig. 9.85 on the left shows the way in which a reptile targets its prey. The insect may not even be aware of the immobile predator. The right image shows the superb eyes of a flying fox (not an insectivore, by the way), which are well-suited for manoeuvring through dense treetops. ⊕ ◂◂◂

Nature has invented and reinvented the eye many times over; so, there must be an enormous evolutionary benefit to having good eyes. The mere fact that insects have been using compound eyes for many hundreds of millions

412

Photographic image and individual perception

of years proves what an important step they must have represented in the evolutionary process. From the perspective of physics, it may be stated that insects are rather “wasteful” in their usage of light due to the absence of lenses: Unlike in lens-based eyes, light rays are barely focused in the compound eyes of insects. However, the following example shows that an even simpler possibility exists. ▸▸▸ A pinhole camera is actually enough! Seeing, in its most basic form, is less complicated than one may imagine. The first attempts at photography show that a simple box impermeable to light is sufficient. A small hole is made at the center of one of its sides, opposite a light-sensitive layer which captures the outside world (Fig. 9.86, left box). In these primitive conditions, a considerable amount of luminosity (like a flashlight) is required in order to illuminate the photo layer adequately.

Fig. 9.86 The simple geometrical background of a camera obscura: The light rays enter a dark box, illuminating the back wall. Right box: When we insert a mirror under 45○ , the image is diverted to the top wall.

When we insert a mirror into our dark box (Fig. 9.86, right box), we can divert the created image, and thus, make it visible on a waxed paper. (We just have to keep our head and the upper part of the box shrouded by a piece of black cloth.) An experiment, such as the one by Marianne Kampel, Christoph Mandl, and Markus Jagersberger, may now be conducted: The “box” may be a cuboid tent – completely impermeable to light – with a very small hole. If an observer is put into the tent, they would be astonished by a projection of the outside world onto the walls and the floor (once their eyes have adapted to the dark-

9.4 Geometry at the water surface

413

Fig. 9.87 Left: The principle of the “camera obscura”. Right: A tent impermeable to light.

Fig. 9.88 Incredible: This is what the inside of the tent looks like once the eyes have had enough time to adapt. Almost razor-sharp images of the outside world are wrapped around the inside of the cuboid, and even around its edges!

ness). This effect can also be “proven” fairly easily by taking a photograph from inside the tent with a very long exposure time (Fig. 9.88). ◂◂◂ ▸▸▸ The small step towards a real camera Pinhole cameras have the disadvantage that only very little light can enter the system. When we enlarge the pinhole, the image immediately becomes blurred. We have to insert a convex lens that collects the light on the back plane (Fig. 9.89 on the left). When the focal length of the lens is chosen such that a point of interest is “bundled” via a light cone on the back plane (according to Fig. 9.31), we get a sharp (and bright) image. Remarkably, this cone can again be “deviated” by a 45○ -mirror like the one in Fig. 9.86, which projects a clear and sharp image onto a sheet of waxed paper (Fig. 9.89 on the right). This is how nature developed different eyes: A pinhole had to be covered by a refracting lens (Fig. 9.90). Some “fine-tuning” was achieved by inserting an additional lens, which enabled a slight varying of focal length (Fig. 9.81). The combination of multiple lenses, as found in sophisticated optical objectives, is probably a human invention (Fig. 9.91). ◂◂◂

414

Photographic image and individual perception

Fig. 9.89 When we enlarge the pinhole, we allow more light to enter, but we need a convex lens.

Fig. 9.90 Opening and closing the pinhole . . .

Fig. 9.91 Placing several lenses in front of another makes the situation more complicated.

10 Kinematics: Geometry in motion

Kinematics – the geometry of motion – may very well be called the “paradise of geometers.” It is where the insights and theorems of geometry are applied to solve difficult problems. Some of the basic laws of kinematics appear remarkably simple, the basic point being the formulation of geometrical or physical propositions about moving mechanisms. The paths of points or the envelope curves (or surfaces) are of particular interest, as are the considerations about instantaneous velocities and accelerations. In the plane, any system of arbitrary complexity rotates at any given moment about a precisely determined (instantaneous) pole, which may also be a point at infinity. From this insight, conclusions may be drawn about path tangents and instantaneous velocities. Envelopes of moving curves can also be captured in this way, as well as curvatures and instantaneous accelerations of path curves, provided that certain additional information is given. The most important types of transmissions will be categorized and studied in this chapter, with a particular focus on the central role of the mechanical linkages (such as the hinge parallelogram or the antiparallelogram). Many technical challenges can be mastered by their use. The ellipse motion, whose generalization is the trochoid motion, will frequently reoccur in our considerations. Trochoid motion plays an important role in gear theory. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_10

415

416

Kinematics: Geometry in motion

10.1 The pole around which everything revolves Constrained motion of two points If an object can only be moved in a predetermined way, it is undergoing a so-called constrained motion. Let us imagine a triangle ABC in the plane (such as our set square). If we move A along a predefined curve a and simultaneously move B along another predefined curve b, then C (and any other point of the “triangle system”) is left with no choice: It is constrained to move along a path curve c, which is already predetermined. ▸▸▸ Two-point guidance with a bicycle The bicycle in Fig. 10.1 is driving on a wavy road. It is intuitively clear that points on the bicycle frame, such as the saddle’s point of support, “have no choice.”

Fig. 10.1 Two-point guidance

The bicycle would move in exactly the same if its wheels did not spin but were simply pushed along the road. The two contact points between the wheels and the road are precisely defined, and the path curve (including the motion) is thus determined. ⊕ Remark : As the picture shows, the cyclist is not rigidly connected to the bike. For him, the aforementioned rules only apply to a limited degree – small deviations from the theoretical path result, among other factors, from the pedaling motion and from the absorption of impacts. ⊕ ◂◂◂

Two path normals are sufficient In the first chapter (Fig. 1.8), we showed the following: Two pairs of (directly congruent) positions A1 B1 C1 and A2 B2 C2 of a triangle ABC can be transferred into each other by a uniquely defined rotation. The center of the

10.1 The pole around which everything revolves

417

rotation P12 is located at the intersection of the perpendicular bisectors of A1 A2 and B1 B2 . The third bisector C1 C2 automatically passes through P12 . Let us now consider a kind of “stroboscopic pair of photographs” within a very short period of time. Both triangle positions will be nearly identical, but the construction of the bisector intersection point will be exactly the same. The bisectors of two points A1 , A2 on a curve a and B1 , B2 on a curve b are to be determined. A1 A2 and B1 B2 are, thus, the chords of the predefined curves a and b. We can use this insight to make the following limiting-case extrapolation: If the time interval for the stroboscopic photos is “infinitely small,” the chords of a and b will converge towards the tangents of the curves. The perpendicular bisectors, thus, become the curve normals at A and B (Fig. 10.2). Their intersection yields the precise instantaneous center of rotation – the instantaneous pole P . All other limiting positions of the perpendicular bisectors (i.e., the path normals) automatically pass through P . No matter how complicated the motion of our set square becomes, if we mark the path curves a and b of two points A und B, we can reconstruct the motion by moving A on a and B on b. This leads us to the following always pertaining, fundamental Theorem of path normals: At any instant of a planar motion, all path normals pass through a single point – the instantaneous pole. During translations, the instantaneous pole is a point at infinity.

Fig. 10.2 Constrained motion: two-point guid- Fig. 10.3 In which direction does the saddle ance (A ∈ a, B ∈ b) move?

▸▸▸ Two-point guidance with the bicycle (continuation) Let us construct the path tangent of a saddle point C in Fig. 10.3. Solution: The path normals of the wheel contact points A and B are given by the

418

Kinematics: Geometry in motion

shape of the road. All path normals pass through their intersection point, the instantaneous pole P . The path tangent tC of C is, thus, orthogonal to P C. ⊕ Remark : If the bicycle moves on a planar road, it undergoes a pure translation, where all path tangents are parallel. The instantaneous pole is the point at infinity of the normal direction. ⊕ ◂◂◂

Instantaneous velocity During rotations, the distribution of velocities is very simple: The center of rotation does not move at all, and thus, it has zero velocity. The further all other points are from the center, the faster they move. The absolute value of the velocity increases linearly with the distance from the center of rotation.

Envelopes If we know two path normals of an arbitrary constrained motion, we can determine the path tangent for any point. However, this is not enough, because it is also true that: If a curve c is moved by a constrained motion, then the pedal points of the normals drawn from the instantaneous pole on c are points of the envelope of c. Proof : We can calculate points of the envelope by intersecting two immediately succeeding positions of c. We shall now show that these intersection points are precisely the pedal points Ti of the normal: Like any other points, they have path tangents which are orthogonal to the line connecting them with the instantaneous pole P . However, following the definition of the pedal point of the normal, this path tangent touches the curve c. This means that the points Ti are the ones that currently move along c. A “neighboring position” of c thus intersects c at the points Ti .

⊙

Fig. 10.4 Astroids and parallel curves as the envelopes of a straight line

In the most simple case, the curve c is a straight line. It thus contains exactly one pedal point of the normal through the pole. Fig. 10.4 (on the left)

10.1 The pole around which everything revolves

419

illustrates that a curve is produced if the straight line c is moved such that a fixed point X is directed along the x-axis and another fixed point Y is directed along the y-axis. The resulting curve is also called an astroid, which we have already discussed in a prior chapter. In Fig. 10.4 on the right side, a second straight line c, which is parallel, and therefore, at a constant distance d to c, is carried along. It envelops a parallel curve to the aforementioned astroid. Envelopes of straight lines often possess cusps. Cusps occur in astroids, considered as envelopes of a straight line, if the instantaneous pole lies on the straight line – a situation which may arise in the course of the motion. The cusps of the parallel curves occur at the same time.

Fig. 10.5 Paths of points and envelopes of straight lines of a cycloid motion

A special situation occurs if a moving point happens to coincide with the instantaneous pole. The rolling of a wheel along a straight line (Fig. 10.5) is an example of such an occurrence. This type of motion is called cycloid motion. In the course of the motion, each point on the circumference of the wheel will coincide with the straight line, which produces a cusp on its path curve. Interestingly enough, a wheel spoke (half of a diameter of the circle) envelops a similar cycloid of half the size. The instantaneous pole of a rolling wheel is the contact point of the wheel with the fixed straight line. For this point the instantaneous velocity equals zero, and it lies on the path normal of the center of the circle, whose path is a straight line parallel to the horizontal road.

Fig. 10.6 Envelope of a generic straight line

The envelope of a generic straight line during a cycloid motion is a curve which is an offset curve of a cycloid (Fig. 10.6): In this case, one can simply translate the straight line by a constant vector into the center of the circle.

420

Kinematics: Geometry in motion

Fig. 10.7 Envelope of a special circle

If we take a circle (instead of a straight line) in the moving system of the wheel, we get an envelope with two branches, which stem from two possible circle normals (respectively) through the instantaneous pole (Fig. 10.7). Let us first consider the special case where the center of the circle M lies at the boundary of the rolling circle. We are now faced with positions where M becomes the instantaneous pole. In this case, every point of the circle which was moved along is a pedal point of the normal through P . Therefore, these circle positions are parts of the envelope. In Fig. 10.8, the center of the circle is no longer a point at the edge of the rolling wheel (on the left, it is inside the wheel, and on the right, it is outside). The last two figures permit an interesting spatial interpretation: If we interpret the separate positions of the moved circle as normal views of spheres (Fig. 10.8 in the middle), then we can recognize the normal view of a helical pipe surface whose pitch is (at first) precisely defined. If we then apply an orthogonal affinity in the direction of the straight line that is the midpoint’s path, we can vary the pitch arbitrarily.

Fig. 10.8 Envelope of general circles and a spatial interpretation

The outline of a helical pipe surface in a normal projection is composed of parallel curves of an affinely distorted cycloid. The cycloid is a frequently recurring curve. As Johann Bernoulli discovered in 1696, it is the curve connecting two points A and B located at different heights, along which a particle under influence of gravity can get from A to B in minimal time (ignoring friction). In this particular context, it is called the brachistochrone curve.

10.1 The pole around which everything revolves

Fig. 10.9 Brachistochrone curve

421

Fig. 10.10 Cycloidal pendulum

A pendulum which swings on a cycloid in the way pictured in Fig. 10.10 can be used as an exact harmonic pendulum. The frequency of oscillation is independent of the amplitude. In this context, the cycloid is called the tautochrone curve. The pendulum clock, which relies on this property of the cycloid pendulum, dates back to Huygens, who utilized the fact that the evolute of a cycloid is another congruent cycloid. However, the error caused by friction was greater than the increase in accuracy due to the isochronicity of the oscillation.

Fig. 10.11 Envelopes of straight lines

Envelopes often occur in reflections and tend to produce beautiful patterns. Fig. 10.11 shows the reflection of a CD in the LCD screen of a laptop. The ellipses around the center of the reflection come from the CD’s circular edges. The pointed focal line at the center, however, is only indirectly caused by the reflection. As with the Newton rings in application p. 215, it is actually a result of interferences. The curve remains visible – if slightly less so – after the disk has been partially covered. But what exactly do reflections have to do with “motion”? Well, that is a matter of interpretation. One might say: “ ‘If a light ray moves along a curve . . . ”. The scale of the time during which this “motion” occurs is irrelevant. It may even happen at speed of light.

Relative motion As a spectator, it is often practical to adapt to an existing motion. For example, in order to understand the path of the Sun on the firmament, it is useful to switch from the “terrestrial system” into the “solar system.” The solar system, however, is itself in motion: Not only does it move away from the position of the Big Bang at very high speed, it also rotates about the center of the Milky Way.

422

Kinematics: Geometry in motion

Fig. 10.12 Relative motion: The excavator is being moved by its own scoop.

Fig. 10.13 Relative motion: It is not the tool that moves but also the work piece!

If one follows this logic to its end, one must conclude that all motion is relative. We can hold onto a wooden piece and sculpt its outer layer (as sculptors do), or we can clamp it into a lathe and let it spin so as to change it by means of a lathe tool (as in Fig. 10.13). We will soon deal with more examples of relative motion (such as application p. 444).

10.2 Different mechanisms

423

10.2 Different mechanisms Let us shake hands!

Fig. 10.14 Simulation of the opening and closing of a palm

The act of shaking hands is a multi-layered process, and most of it happens inside the brain, including the steering of the hand and the impressions of the “receiver.” Being greeted by the wooden hand in Fig. 10.14, one is surprised by the realistic nature of the feeling (it is, however, a left hand, which relates to the android we used in the following example). The mechanism itself is as simple as it can be: A tug on a bundle of strings pulls the slightly curved fingers at their lower joints. The angles of rotation of the separate fingers are slightly different, which can be regulated by the distance of the strings’ starting points. The thumb rotates about its “own” axis, which causes the subjectively important embracing sensation. Such a wooden hand, as simple as it is, can already be used to grab and reposition certain small objects (like chess pieces). One may insert an additional moving hinge joint to each finger, which produces a so-called two-bar linkage.

Two-bar linkages A rod AB with length r rotates about its fixed endpoint A while a second rod BC with length s rotates about its end point B. This mechanism can be used to reach any point within a circle with the radius r + s about A as long as s is greater than r (otherwise, it is an annulus with an inner radius of r − s): The position of B is derived from the intersection of the two circles – one about A with a radius of r and another about C with a radius of s. Two solutions exist if A and C are assumed to be fixed.

424

Kinematics: Geometry in motion B

r A

s

C

Fig. 10.15 Two-bar linkage: Any point C within a circle or an annulus about A can be reached. On the right: The arm of a pepper grinder can be freely rotated in one direction.

▸▸▸ The chess-playing android The late 17th and the early 18th century were the age of “androids” – humanlike automata whose intricate mechanical interior rendered them capable of remarkable feats. Wolfgang von Kempelen famously developed a “chessplaying Turk” (Fig. 10.16).

Fig. 10.16 The Chess-playing Turk and historical attempts at explaining the phenomenon

Many contemporaries have racked their brains trying to explain the supposed artificial intelligence in mechanical terms, while the actual solution was something of a cheat: A little person who was hidden inside the box managed to receive information about what was happening on the chess board, and steered the left hand of the marionette so as to move the chess figures to the intended spot. At the time of the android’s creation, the real secret was never lifted. An explanatory theory by Joseph Friedrich von Racknitz was verified at the University of Applied Arts Vienna in a computer simulation, and a subsequent mechanical realization (Fig. 10.17) was deemed to be successful. The hand in Fig. 10.14 was made of wood, like much of the rest of the automaton.

10.2 Different mechanisms

425

Fig. 10.17 Possible kinematic model of the chess-playing android (according to Joseph Friedrich von Racknitz )

Without further elaboration, it is sufficient to say that the core piece was a two-bar linkage formed by the upper and forearm. ◂◂◂ ▸▸▸ The joints of articulate animals In articulate animals (insects, spiders, and crabs being among them), mechanisms such as the two-bar linkage (or their generalizations) are implemented to perfection. The complex motions of the legs, claws, and pincers are not even directed by the brain but by “quasi-microprocessors” located directly in the joints!

Fig. 10.18 A multitude of two-bar linkages and their generalizations

Not quite as trivial as the limbs – and only visible in a close-up photograph: The bees in Fig. 10.19 extend a sort of “auxiliary jaw” where their tongue is located. Through this auxiliary jaw, the bee’s tongue can penetrate the farthest corners of the mallow blossom pictured in the photograph. ◂◂◂

426

Kinematics: Geometry in motion

Fig. 10.19 Something close to a two-bar linkage: One can observe the mandibles (including the tongue) of the black carpenter bee.

▸▸▸ Leonardo’s cranes Cranes have been “commonplace” for much of the last century, and it is,

Fig. 10.20 Three sketches by Leonardo da Vinci

therefore, easy to forget just how innovative the sketches made by the genius from Tuscany actually were. You can exercise your spatial imagination by rotating the various wheels in your mind and considering the directions into which the loads may be heaved. ◂◂◂

The hinge parallelogram If a parallelogram ABCD is held at one side (for instance, AB), and if the parallel side (CD) is left to rotate, one deals with a hinge parallelogram (Fig. 10.21). Each point that is connected to CD describes a path circle congruent to the path circles of C and D. Hinge parallelograms are often found in daily life, for example, in desk lamps or in letter scales (Fig. 10.22). Parallel translations in all directions can be accomplished by a combination of multiple hinge parallelograms (old drawing machines in drawing offices employed this trick). A particularly clever variant is visible in Fig. 10.23, which shows a tripod that can be used to keep heavy cameras steadily parallel to the ground – even while walking.

10.2 Different mechanisms

427

Fig. 10.21 A hinge parallelogram: Each path is a circle.

Fig. 10.22 The hinge parallelogram in a letter scale and in a designer lamp

Fig. 10.23 Hinge parallelograms in a portable tripod (Robert Eder)

▸▸▸ Pantograph The pantograph, sometimes called “lazy tongs” (Fig. 10.25), consists of parallelograms strung together and can often be found, for instance, in the adjustable mounting of lamps, sunblinds, or even whole platforms, as in Fig. 10.26. ◂◂◂

428

Kinematics: Geometry in motion

Fig. 10.24 As ingenious as it is simple: How to turn a cardboard box into a lectern (by Christian Bezdeka www.bezdeka.com): This construction is based on so-called lazy tongs. In its final position, the lectern can even be tilted!

Fig. 10.25 Panthographs . . .

Fig. 10.26 . . . in theory and practice

Antiparallelograms If a hinge parallelogram is stretched into its longest form, its motion may continue in two different ways: either, as outlined before, as a parallelogram or as an antiparallelogram, with only one pair of parallel opposite sides. In Fig. 10.28, such a hinge LABM can be seen. A moves on a circle about L and B on a circle about M . Thus, the two longer sides are path normals, and their intersection is the instantaneous pole P . The sum of the distances LP and M P = AP is constant (= LA), which causes P to move along an ellipse with the focal points L and M . For reasons of symmetry, an ellipse which is symmetric with respect to the ellipse’s tangent in P and which has the focal points A and B exists in all positions and belongs to the moving system.

It does not always have to be a uniform rotation . . . The hinge antiparallelogram has an interesting application: The pole curves are congruent ellipses which roll onto each other. If these ellipses are furnished with gear flanks, they can be made to roll, as in Fig. 10.29. If, instead of the principal axis of the ellipse being held at rest, the single focal points of both ellipses are fixed, the uniform rotation about one focal point can be transformed into a periodically non-uniform rotation about the other focal point. Conversely, it is sometimes possible to diminish the effects

429

10.2 Different mechanisms

Fig. 10.27 Practice and . . .

Fig. 10.28 . . . theory of the antiparallelogram

Fig. 10.29 Elliptic gears

of certain non-uniform rotations and even to equalize these rotations in ideal situations.

Fig. 10.30 Elliptic gears move downwards.

Fig. 10.30 shows a very original method of propelling elliptical gears: Both gears are placed within a cylindrical container – bounded by cylindrical discs – and are moved downwards by gravity. Observing elliptic gears in slow motion may, to some readers, be more calming than an hourglass, though a certain similarity can be observed: Once the gears have reached the bottom, the entire cylinder can be turned upside down so that the motion proceeds anew. Notice the small pocket of air which has crept beneath the right gear.

The crank shaft If a point A is moved on a circle a about a fixed point L, and a point B which is rigidly connected to A is also moved along a straight line b (Fig. 10.33), we

430

Kinematics: Geometry in motion

Fig. 10.31 Ancient gears? Columns which have fallen apart!

Fig. 10.32 Crank-shaft propulsion

Fig. 10.33 Crank shaft of an Otto engine

are dealing with a crank shaft. Fig. 10.32 shows the crank shaft propulsion of a workbench and Fig. 10.33 the crank shaft of an Otto engine (see also Fig. 10.35 in the top right corner). B1

P1

P4

B4

ω1 ω1P2

B2

B3

P3

ω2 ω2

A4

A1 L1

v⃗A1

L2 A2

v⃗A3

L3

v⃗A4 L4

A3

v⃗A2

Fig. 10.34 Construction of the velocity vector of B in four different positions

▸▸▸ How fast is the piston? When the piston oscillates inside the cylinder of an Otto engine, its speed changes dramatically. In its deadlock positions (highest and lowest) the velocity is zero. In between those positions the velocity varies considerably. In

10.2 Different mechanisms

431

order to determine the speed in an arbitrary in-between position, we first look for the instantaneous pole P (Fig. 10.34). The pole P is found by intersecting two path normals: The point L of the crank is fixed. The endpoint A of the crank rotates uniformly around L and its orbit is a circle. Therefore, the path normal in A is the line LA. The point B on the connecting rod is forced to run on the vertical axis of the cylinder. Thus, its path normal is the horizontal line through B. The position of P is now determined, and it is the only point of the system connected with AB with a velocity of zero. In that very moment, he whole system rotates around P . The velocity of any point of the system AB is proportional to its distance from P . Since we know the velocity vector v⃗A of the point A (a vector of constant length perpendicular to LA), we can determine the velocity vector v⃗B in B via similar triangles: The angle ω from the normal to the end points of the velocity vectors is equal. ◂◂◂

Fig. 10.35 Sawmill according to Leonardo da Vinci , with remarkably detailed solutions

▸▸▸ Sawmill by Leonardo da Vinci Leonardo da Vinci has been known for his ability to plan mechanical constructions down to their smallest detail, without necessarily realizing these ideas in practice. His sawmill (Fig. 10.35 on the left) is still in use today and has undergone only slight changes. The crank shaft propulsion (Fig. 10.36), propelled by water, lies at its core.

Fig. 10.36 In the sawmill, propulsion is generated in a manner comparable to that of the piston engine.

432

Kinematics: Geometry in motion

The platform that pulls the pieces of wood towards the running saw blade is driven by a subtle mechanism: A rod s, which is rigidly connected to an axis a, is forced by a loop to resonate with the driving rod. Another rod t, to which the hook h is attached, is also rigidly connected to the axis a. When swinging back, this hook attaches to a cog, and when swinging forward, it glides over the tips of the triangular teeth – thus, it can move the gear forward step by ◂◂◂ step, which in itself pulls the platform over a shaft.

Fig. 10.37 Path curves of four-bar linkages

General four-bar linkages (hinge quadrangles) A four-bar linkage (hinge quadrangle) is a mechanism made of four rods. Depending on the length of these rods, there exists a huge number of variations – and a corresponding multitude of applications. Once again, let LM AB be the hinges of the quadrangle (Fig. 10.37). If the points L and M are fixed, then the motion of the system connected to the rod AB is called a linkage motion and the path curves are called linkage curves. The paths of the points A and B are circles about L and M . The corresponding path normals are the linkages (or swings) LA and M B. The instantaneous pole P can be found at the intersection of the path normals. Each point C of the linkage system always moves orthogonally to the associated pole ray P C. In addition to the special four-bar linkages, the general forms are also widely in use (Fig. 10.41). The advantage always remains the same: The devices are easy to manufacture and to utilize, and beyond that, they are also very robust.

10.2 Different mechanisms

433

The multiformity of the path curves is virtually unbounded, and the only challenge lies in finding the right rod lengths for a particular problem. Once an appropriate hinge quadrangle has been found, it might be necessary to compensate for the differing path velocities of a system point. Many critical points often move at very high speeds, whereas other, less important areas are nearly fixed in dead-point positions. Here, one should attempt to configure the propulsion of the hinge in a flexible way.

Fig. 10.38 Four-bar linkage with approximate straight line guidance (oil pump)

Fig. 10.39 Four-bar linkage with approximate straight line guidance (crane)

Fig. 10.38 and Fig. 10.39 show two special forms of four-bar linkages that are very useful. You can see an additional auxiliary four-bar linkage (colored red in the sketch), which can be driven by rotation. Note that in Fig. 10.39, the point C ∗ is not directly connected to the linkage. Its path curve is congruent

434

Kinematics: Geometry in motion

to the path curve of C, and the tangent t∗ ∋ C ∗ is always parallel to the tangent t ∋ C. The approximate straight line guidance is of utmost importance in these cases. ▸▸▸ Film gripper What is the mechanism underlying the machine in Fig. 10.40? The point A rotates about the fixed point L. The point B is guided along a circular arc with the center M . Therefore, M B is constant, as is AB. Point C is rigidly connected to AB. The mechanism is obviously a four-bar linkage.

M

Fig. 10.40 Film gripper versions by Leo Mühlfeld (above) and Alan Schiegl (below)

The position of C is chosen in a way that the lower part of its path is almost straight. The hook connected to C can, therefore, grip something like a film or balls (like in the bottom image of Fig. 10.40). ◂◂◂ ▸▸▸ A useful fixing mechanism (“Mole grips” or “Vise-Grips”) Pliers are a hand tool used to hold objects firmly. Locking pliers can be locked into position by means of an over-center toggle action. A lever is used to aid release from the locked position (Fig. 10.41). Due to the toggle mechanism, very high forces can be applied with this type of pliers. Grip pliers can be released by pushing back a lever that overcomes the “dead center” and in turn releases the workpiece. Applications include, for example, the loosening of very tight screw connections, the fixation of workpieces, and the use of pliers as a “third hand”. The series of images in Fig. 10.41 (left) show how the fixed position can be adapted to the diameter of the object that has to be fixed. For this purpose,

10.2 Different mechanisms

435

Fig. 10.41 Pliers with a four-bar linkage and a fixing mechanism

a screw is used. When in the fixed position, there are maximal forces at play. If the screw is correctly adjusted, the fixation process will require hardly any exertion of force, and the force necessary to hold the workpiece in place is ◂◂◂ thus even more impressive. ▸▸▸ The front tires have to be rotated asynchronously! What happens if we turn the steering wheel of a car? First, the rotation is transferred onto a horizontal axis by a Cardan shaft, where it is converted into a translation by a gear rack (Fig. 10.42). This propels a hinge trapezoid, which rotates the front wheels – and quite ingeniously at that!

Fig. 10.42 Different rotations of the front wheels. Each tire has a different instantaneous speed proportional to its distance from the instantaneous pole.

Let us now literally “track back” the process: In order to ensure optimal steering, the path normals of the wheels’ four contact points must pass through a

436

Kinematics: Geometry in motion

single point – the instantaneous pole. Pairs of wheels are mounted on an axis, and thus, all wheels must be perpendicular to the straight lines that connect their centers with P . This can be accomplished with a four-bar linkage. ◂◂◂ ▸▸▸ Cognate linkages Cognate linkages are linkages that allow to generate a coupler curve in different ways. In case of four-bar linkage coupler cognates, the RobertsChebyschev Theorem states that each coupler curve can be generated by three different four-bar linkages (Fig. 10.43). These four-bar linkages can be constructed using similar triangles and parallelograms (left image). N∗ F∗

N H∗

F

H G

E∗

E

G∗

C

C∗

L L∗

A∗

B∗

M

A

M∗

B

Fig. 10.43 One and the same coupler curve can be generated in three different ways (construction and different positions). The triangles LM N and ABC are similar.

The possibility of generating a coupler curve in multiple different ways has one big advantage: there are three distinct ways to find a desired mechanism that are most suitable to fulfill the requirements. In technology, it is often necessary to use straight line guidances. The linkages, however, must run smoothly or must not require space at certain positions. F A B L

L M E

G

M N

N

H Fig. 10.44 The search for an alternate mechanism for a “stepper” fitness machine. The construction also works when the triangles LM N and ABC are degenerate.

10.2 Different mechanisms

437

Fig. 10.44 illustrates how one can replace the black fourbar linkage by either a green or a blue one. Consider a “stepper” in a fitness center where the trainee needs to move their legs in the given way. The black linkage does not quite as smoothly as desired (Fig. 10.44 to the right) since there might not even be enough space left for the movement. Consequently, one of the two other linkages might be better suited to the task. In this special case, the triangle ABC degenerates: C lies on the prolongation of AB. Then N has to lie on the prolongation of LM in the same ratio. ◂◂◂ ▸▸▸ A sugar bowl and a four-bar linkage The sugar bowl pictured in Fig. 10.45 implements a classical, though barely recognizable, planar four-bar linkage.

Fig. 10.45 The second image from the left shows which points remain fixed (L and M ) and which have circular paths: A and B, and thus, also D.

Let us consider the three points M , A, and B, which determine the vertical symmetry plane of the hinge. Now, let us further consider the fourth point L of this plane (it lies at the center of the imagined, horizontal axis of the mechanism, which appears almost projecting in the photo). A hinge quadrangle LM AB is thus defined. In order to fulfill the condition that the lid should be closed in the stretched position on the left, an imaginary, rigid triangle M BD is also moved. The segment BD materializes through the circular lid, and the segment AB is likewise curved for aesthetic reasons. The designers of the Biedermeier period ◂◂◂ apparently had a penchant for hinge quadrangles. ▸▸▸ How to translate a continuous rotation into an intermittent rotation In technology, one task that needs to be performed very frequently is a version of “stop and go”, or rather “stop and rotate”. This mechanism is used, for example, in money counting machines, film projectors, tool changers in CNC machines, and many more. The so-called Maltesian gear (also known as Geneva drive) accomplishes this quite efficiently. Fig. 10.46 illustrates how a rotating dark blue disk drives a light blue cross in such a way that 3/4 of the time nothing happens: The rotating pin E is not

438

Kinematics: Geometry in motion

E1 E2

E5 E3

C1

C2

C4

E4

C5

C3

Fig. 10.46 The driven cross rotates 90○ and then stands still for a while.

in contact with the driven system (left). In the center image, E hooks into the slot, drives the cross (positions E2 to E5 ), and leaves the driven system. A point C of the driven system rotates 90○ during a full opposite rotation of the blue disk and then then rests three times as long. ◂◂◂

If the arms could change their length We have thus far discussed mechanisms with fixed arm lengths, which have obvious advantages with regard to stability under heavy load. ▸▸▸ A hinge quadrangle with a single variable

Fig. 10.47 Hammer mill after Leonardo da Vinci

After the example of the robot arms, the mechanism behind Leonardo da Vinci’s hammer mill appears to be especially interesting. The simulation in Fig. 10.47 shows the propulsion of a hammer by the rotation of a spiral attached to a shaft. In each position, we are dealing with a quadrangle (A∗ , A, B, B ∗ ) with three constant rod lengths and a variable one (BB ∗ ). The angle ∢AA∗ B may be rigid. ◂◂◂ ▸▸▸ The Stewart platform Contemporary robotics allows us to control any arbitrary motion of a plane

10.2 Different mechanisms

439

Fig. 10.48 A triangular platform ABC which is controlled by three robotic arms of variable length with the fixed points L, M , and N . In the top left corner: “zero position”. On the right: Certain triangle positions are “dangerous” due to the indeterminacy of their robotic motion.

by the use of three arms of varying length (Fig. 10.48). Despite the state-ofthe-art technologies involved, there still exist “unsafe positions”, such as the ones pictured on the right. ◂◂◂

440

Kinematics: Geometry in motion

10.3 Ellipse motion If a rod of fixed length is directed in such a way that its endpoints U and V follow two straight lines u and v, it undergoes an ellipse motion.

Fig. 10.49 Three closely related ellipse constructions

Such a motion is pictured in Fig. 10.49. Both guiding straight lines u and v are orthogonal in this case. We are concerned with the path curve of an arbitrary intermediate point C with V C = a, U C = b. Let F = u ∩ v be the origin of a Cartesian coordinate system and ϕ the rod’s angle of inclination. Thus, C is located at x = b cos ϕ, y = a sin ϕ. This is the parameter representation of an ellipse with axis lengths 2a and 2b. Remarkably, the midpoint R of the segment U V (a = b) describes a circle. ▸▸▸ Construction of paper strips Ellipse motion, by its classical definition, can be accomplished by two orthogonally intersecting guidance rails even though the mechanism is only partially practicable: The motion is jerky, and the stretched positions are undefined, which is why the use of this “ellipse compass” has never really become widespread. The actual significance of this mechanism lies in its easy illustration of the socalled reverse paper strip construction: If an ellipse’s principal vertex (major axis 2a) and a general point P are given, then half of the principal axis a of P needs to be inscribed onto the auxiliary axis (the perpendicular bisector of the principal vertices) in order to get V – though this is possible in two ways. The straight line connecting P and V yields U and thus b. ◂◂◂ We can find the instantaneous pole P of the motion by intersecting the path normals at U and V that are parallel to the axis. Compared to R, P is always at twice the distance from the origin, and thus, lies on a circle about F with

10.3 Ellipse motion

441

Fig. 10.50 Ellipse motion and reverse paper strip construction

a radius U V = a + b and, at the same time, on a circle about R with half the radius (Fig. 10.49 in the middle). The motion of the rod U V could also be forced by letting the Thales circle roll over U V within a circle of double radius. Both circles are named Cardan circles after their discoverer Geronimo Cardano (1501–1576). Cardan circles roll on each other without gliding. Each arbitrary point on the smaller circle becomes, at some instant, the instantaneous pole – the point V , for example, does so in the point V0 on the y-axis (Fig. 10.49 at the center) once R has rotated by an angle of ψ. Following an adaptation of the angle-at-circumference-theorem (p. 10), V has moved on a circle of half the size by an angle of 2 ⋅ ψ. Therefore, we always correlate circular arcs of ̂ equal length – P V on the smaller circle and P̂ V0 on the larger circle – which requires a rolling motion. ▸▸▸ Ellipses as hypotrochoids The rolling motion of the smaller Cardan

Fig. 10.51 Practical realization of the “inner circle rolling”

circle within a second circle that is twice as large can be well simulated by a hollow wheel.(Fig. 10.51) ◂◂◂ ▸▸▸ Gliding or rolling along straight lines In Fig. 10.52 on the left, two circles with constant distance glide along straight lines. Thus, their centers U and V move on straight lines u and v, and we can see an ellipse motion: Every point that is rigidly connected to the moving system has an ellipse as path curve.

442

Kinematics: Geometry in motion

Fig. 10.52 Ellipse motion, not immediately apparent: Two circles (or wheels) are moved along two straight lines. The lengths of the (green) velocity-vectors are proportional to the distance from the instantaneous pole P .

It does not make a difference whether the circles glide or roll: When a cyclist moves from one plane to another like in Fig. 10.52 on the right, every point on the bicycle’s frame is undergoing an ellipse motion. The guiding lines u and v are the parallels to the given planes through the centers of the rolling wheels (or gliding circles), the center O = u ∩ v of the ellipse is their intersection. ◂◂◂ ▸▸▸ Revolving a Reuleaux triangle inside a square Consider a regular triangle ABC (side length r). It can be “rounded of” by means of three circular arcs (radius r = side length), and then has a “constant thickness” r. Thus, it is possible to revolve it inside a square with side length r. There are always two vertices that glide along two perpendicular sides of the square.

Fig. 10.53 A Reuleaux triangle ABC is revolved inside a square: The edges are rounded off “almost circularly” by elliptic arcs.

Fig. 10.53 shows three subsequent positions of ABC when revolving clockwise. Subsequent ellipse motions (axes u, v, center F , Cardan circles p and q)

10.3 Ellipse motion

443

“shake hands” periodically. The center R of the triangle has an almost circular orbit, consisting of four elliptic arcs. Compare also application p. 449. ◂◂◂ ▸▸▸ Drilling quadratic holes in practice Since a Reuleaux triangle can be revolved in a square, one can extend this idea further when thinking about how to drill quadratic holes.

Fig. 10.54 An ordinary drilling machine can be extended by two Cardan shafts . A template of the quadratic hole guides the drill bit.

Fig. 10.54 illustrates in a convincing way how this can be done by using a template. The drill bit, however, has to be moved along an almost circular curve consisting of quarter ellipses (Fig. 10.53). This can be achieved by a combination of two Cardan shafts (explained in Chapter 11, Fig. 11.6).1 ◂◂◂

Fig. 10.55 Rolling of the outer circle instead of the inner circle, realization of the pole ray . . .

▸▸▸ Milling machine for ellipses (Fig. 10.55, Fig. 10.56) The “inner circle rolling” (hypotrochoid motion) with the given radial ratio 1 The

corresponding animation was done by Franz Gruber, inspired by the remarkable website https://www.etudes.ru/ru/etudes/drilling-square-hole.

444

Kinematics: Geometry in motion

(the smaller wheel about R with a radius of 1 rolls within the larger wheel with a radius of 2) can be replaced by a much simpler “outer circle rolling” (epitrochoid motion) by inserting an arbitrary auxiliary gear (midpoint H) which reverses the outer wheel’s direction of rotation. The most important aspect remains the radius of the large wheel, which is twice as large as that of the smaller wheel about R. For the pole P , the relationship F P = 2 RP still applies.

Fig. 10.56 . . . and a practical application

If we fix the centers of the wheels, then a point C on the diagonal of the wheel about R describes, of course, a circle about R – but that is only the case when we refer to the fixed system. However, relative to the rotating larger circle, C moves on an ellipse. The respective tangent to the ellipse is always orthogonal to the pole ray CP . It follows that an arbitrarily-sized circle through C about a point D on the pole ray always touches the ellipse. Wilhelm Fuhs has designed a mechanism (Fig. 10.55, 10.56) capable of realizing the pole ray on which the cylindrical mill rotates about a vertical axis through D. If a sheet were to be mounted onto the large wheel, the milling process would turn it into an exact ellipse. ◂◂◂ ▸▸▸ Oval mill by Leonardo Leonardo da Vinci solved the problem of milling an ellipse in his own way and thus invented the oval mill, which is also a beautiful example of relative motion (reverse ellipse motion):

Fig. 10.57 Oval mill for the milling of ellipses

10.3 Ellipse motion

445

⊕ Remark : The lathe tool remains fixed. The “rotary table” consists of two plates (indicated in green and red). The red plate rotates about its center P . The green plate rotates along with the red one, but is meanwhile translated so that two synchronously moved rails (blue in the picture) always touch a circle through P (also blue in the picture). This causes the center of the green plate to move along a Thales circle with half the radius of the blue circle. We shall now interpret the Thales circle and the doubly-sized circle as the pair of Cardan circles. The green plate, which is connected to the small Cardan circle, then performs an ellipse motion relative to the fixed blue circle: Each point of the green table, thus, has an ellipse as a path curve from the perspective of the fixed system. All that remains is to position a lathe tool “anywhere”, which would cut an ellipse out of the raw material attached to the green plate. ⊕ ◂◂◂

▸▸▸ A compact coupling If we have parallel axes and want to transform the rotation of one axis to the other, we can use John Oldham’s idea to use three disks as in Fig. 10.58.

Fig. 10.58 Oldham coupling: Three discs, one coupled to the input, one coupled to the output, and a middle disc joined in between by tongue and groove.

The tongue and groove on one side is perpendicular to the tongue and groove on the other. The middle disc rotates around its center at the same speed as the other axes. Fig. 10.58 shows that in a projection parallel to the axes, the orbit of the center is a Thales circle with the projection of both axes as diameter points.

Fig. 10.59 Oldham coupling as seen from the middle disk

446

Kinematics: Geometry in motion

In Fig. 10.59, the middle disk stays fixed in the “main position”, whereas the axes sweep harmonically in vertical and horizontal direction. Since the distance between the axes is constant, we deal with an ellipse motion. This is graphically indicated by showing an orbit of an arbitrary in-between point on the connecting line. Therefore, the motion of the middle disk is also a reverse ellipse motion. ◂◂◂ ▸▸▸ Ellipses produced by a crank shaft gear Fig. 10.49 on the right shows a third possibility of producing an ellipse motion – by making use of a special crank shaft: If the shaft F R rotates about F and propels the crank RU along so that U is moved along the straight line u, then a point C on the crank describes an ellipse.

Fig. 10.60 Practical realization of the crank shaft gear

Fig. 10.60 shows a practical realization of this idea. The shaft is actuated over a table surface. The lengths of the shaft and the crank, as well as the distance from the gib, are adjustable. ◂◂◂ ▸▸▸ Ellipse compass according to Hoecken In the pictured mechanism (Fig. 10.61), two (yellow) rods are directed so that their end points move along circles with the adjustable radii a and b. After rotation about the angle ϕ, the intersection point has the coordinates (a ⋅ cos ϕ, b ⋅ sin ϕ), and thus, lies on an ellipse.

Fig. 10.61 Ellipse compass by Hoecken

In this case, the mathematical explanation is easier than the geometrical one, because the intersection point of the rods is, from a kinematic point of view, not so easy to capture. ◂◂◂

10.3 Ellipse motion

447

▸▸▸ Another ellipse compass Another beautiful ellipse compass (the last one to be discussed here) can be seen in Fig. 10.62. It realizes the classical two-point guidance, though this is only apparent upon closer inspection.

Fig. 10.62 Ellipse compass with “hidden” straight line guidance

A big (red) circular disk is moved parallel within a rectangular boundary. Thus, its midpoint moves on the perpendicular bisector of the shorter side of the boundary. A smaller (blue) circular disk is moved analogously, so that its midpoint remains on the perpendicular bisector of the longer side of the boundary. The distance of the centers of the circle is adjustable by slot guides, just as the distance of the drawing pen may be varied. ◂◂◂

General ellipse motion Up to this point, the guiding straight lines of the ellipse motion were always mutually orthogonal. In the general case, however, it can be said that: If a rod of fixed length is directed such that its end points U and V are moved along the arbitrary intersecting straight lines u and v, then each point which is rigidly connected to the rod describes an ellipse. Proof : The intersection F = u ∩ v is the midpoint of the path curve. The circle q through U , V , and F (midpoint R) can be interpreted as the peripheral circle over the segment U V due to the fact that the angle ∢U F V is constant (see also Fig. 1.7). The radius of q is, thus, likewise constant. The instantaneous pole P is given as the intersection of the path normals in U and V , according to Thales’s theorem it also lies on q, namely opposite F . Thus, F P is constant, and P moves on a circle p about F . The radius proportion of the circles p and q is 2 ∶ 1, which means that the circles p and q are the Cardan circles of an ellipse motion. Let us now consider the elliptical path of a point C which is rigidly connected to U V . The diameter CR of q intersects q at the points X, Y . These points describe “infinitely thin” ellipses through F and thus segments. According to Thales’s the-

448

Kinematics: Geometry in motion

Fig. 10.63 General ellipse motion

orem, the straight lines F X and F Y are orthogonal. The given motion is, thus, also forced if the rod XY of fixed length is moved along two straight lines which intersect orthogonally. These are, therefore, the axes of the path ellipse of C. ⊙ ⊕ Remark : The point C might, for instance, be given through its distances to U and V . The triangle U V C can then be positioned onto U V in two ways, which, in turn, yields two different results (Fig. 10.63 left and right). ⊕

Fig. 10.64 Revolution within a triangle

▸▸▸ Revolution within a triangle or a pentagram Fig. 10.64 shows the revolution of a square (or “digon”) bounded by circular arcs within an equilateral triangle. The circular arcs have their centers on the opposite arc, producing a “curve of constant width.” During revolution, an alternation between three different ellipse motions occurs. The digon, in particular, produces traces of metal due to the frequent revolutions. They are the elliptical path curves of the vertices. Fig. 10.65 shows the revolution of a three-leaved curve of constant width within a pentagram. ◂◂◂ Fig. 10.66 illustrates the revolution of a curve of constant width within a parallel strip. The path curves of the corners consist of pieces of straight lines and cycloids. The path of the midpoint resembles a sine curve. Compare also application p. 442.

449

10.3 Ellipse motion

Fig. 10.65 Revolution within a pentagram

Fig. 10.66 Revolution of a curve of constant width within a parallel strip

▸▸▸ The world’s first seven-sided coin The British 50p coin (Fig. 10.67) was first issued in 1969. Since then, several heptagonal coins have been introduced to the market worldwide.

Fig. 10.67 Reulaux heptagon

A geometer will immediately think of a way to construct such a curved regular polygon when the circumcircle is given. This is, in fact, quite easy and there are several video tutorials on the Internet that give helpful instructions. The task of finding the correct radius for the rounding circles will be left to the ◂◂◂ reader. The result should be a curve of constant thickness . . .

450

Kinematics: Geometry in motion

10.4 Trochoid motion The name comes from the Greek word for wheel, “trochos”. We have seen how an ellipse motion can be forced by the revolution of a circle as long as the radii of both Cardan circles define the ratio 2 ∶ 1. However, what happens if this ratio is changed?

Fig. 10.68 Gardeners often exhibit an inclination towards geometry: The pictured rose patch in Schönbrunn is a good example of that (see also Fig. 10.69 on the right).

If a circle with an arbitrary radius rolls within a fixed circle, then each point connected to the rolling circle describes a hypotrochoid.

Fig. 10.69 Hypotrochoid motion as a generalization of ellipse motion

Fig. 10.69 shows this generalization with the ratios 2 ∶ 1, 3 ∶ 2, and 5 ∶ 1 for the radii. The instantaneous pole is located at the point where the rolling circles touch and has an instantaneous speed zero. The corresponding path normal of a point’s path curve passes through it. If the radius of the rolling circle exceeds the radius of the fixed circle, then the rolling circle encompasses the fixed circle, and the point of contact is located on the outside. (This situation is sometimes referred to as a epitrochoid.)

10.4 Trochoid motion

451

Fig. 10.70 Hypotrochoid or epitrochoid motion?

Fig. 10.70 illustrates this case for three different ratios of radii. The path curves of points attached to the moving circle are stretched, have cusps, or are engulfed, depending on whether the point lies inside, on, or outside the rolling circle.

Fig. 10.71 Outside rolling for different radius proportions

A further generalization is given if the moving circle is definitively rolled on the fixed circle. Fig. 10.71 shows the corresponding path curves for the same radius proportions as before. If a circle with an arbitrary radius rolls on a fixed circle, then any point connected to the rolling circle describes an epitrochoid. Trochoids are often found in geometry. If the ratio of the radii is a rational number, then the curves are algebraic and closed. The curves are even rational, i. e., they admit a rational parametrization. Examples include the ellipse (of degree two) and Pascal ’s limaçon (of degree four), which often occurs as the locus (Fig. 1.23) or normal view of a space curve (Fig. 11.3 on the right). Fig. 10.72 and Fig. 10.73 show some more algebraic examples of trochoids. When the moving Cardan circle is rolling on the fixed Cardan circle, the ratio of the radii determines the algebraic degree of the path curves. Among the path curves of moving points we always have curves with loops, cusps and

452

Kinematics: Geometry in motion

stretched curves (depending on whether the point is outside, on, or inside the rolling circle).

Fig. 10.72 Epitrochoids: The green Cardan circle is rolling on the outside of the fixed red Cardan circle. From left to right the ratio between the radii (red:green) is −1 ∶ 1, −2 ∶ 1, and −5 ∶ 1.

Fig. 10.73 Hypotrochoids: The green Cardan circle is rolling on the inside of the fixed red Cardan circle. From left to right the ratio between the radii (red:green) is 4 ∶ 3, 3 ∶ 2, and 5 ∶ 2.

The black curves in Fig. 10.72 and Fig. 10.73 are multicuspidal curves. In Fig. 10.72 on the left one can see once more the cardioid (a limaçon of Pascal, degree 4), in the middle we have the two-cuspidal nephroid (degree 6). In Fig. 10.73 one can see the astroid (degree 6) on the left and Steiners tricuspidal hypotrochoid (degree 4) in the middle. ▸▸▸ Wankel’s engine A classical technological application of trochoids is the Wankel engine. The section of the piston chamber (Fig. 10.74) is an epitrochoid, which is thrice traced by the vertices of the synchronously moved equilateral triangle. Note that this epitrochoid also occurred in Fig. 10.70 in the middle. It can be proven that epicycloids can always be generated in two different ways ([28]). The envelopes of the triangle sides fit easily into the piston chamber. In order to accomplish a greater compression, the central piece is thickened such that the envelopes are as large as possible while still fitting in the chamber. ◂◂◂

453

10.4 Trochoid motion

Fig. 10.74 Wankel engine

Fig. 10.75 Relative motion of an inner planet on the celestial sphere

▸▸▸ Planetary motion The trochoid motion was originally called planetary motion. An astronomer observing the path curves of our neighboring planets eventually discovered curves which are nearly trochoidal: Due to our own revolution around the Sun, the rotation of both planets is superimposed.

Fig. 10.76 Relative motion of the inner planets

Fig. 10.76 illustrates the rotation of the planets about the Sun – in slightly deviating planes but with highly varying velocities. If, at a specific time of day, we mark the position in the sky at which such a planet is seen, we will notice that it essentially moves on a great circle: the equinoctial line. If the planet’s path plane is additionally inclined relative to the path plane of the

454

Kinematics: Geometry in motion

Earth (in the case of Mercury, this inclination equals 7○ ), then the motion of the planet diverges from the equinoctial line. In Fig. 10.75, Mercury’s orbit was simulated, but it was done with a threefold inclination of its path in order to emphasize the effect. We can see that these cases may, indeed, have something to do with trochoid motions, but certainly not precisely so.

Fig. 10.77 The four biggest moons of Jupiter. The photo to the left shows how one can see them with a good eye, the photo to the right was taken with a 3,000 mm lens and 1 second aperture time. During that second, the whole system rotates relatively to the observer on Earth in such a way that it is hard to get a sharp image without tracking the system.

Fig. 10.78 A simulation of different relative positions of the four moons

Fig. 10.77 shows a famous situation in the sky: Jupiter with his biggest moons (Io, Europa, Ganymed, and Callisto) – almost in a row. After the telescope was invented, these moons were discovered at the same time (1610) by Galileo Galilei in Padua and Simon Marius (Mayr) in Ansbach. This discovery expedited the establishment of Copernicus’ heliocentric system,

10.4 Trochoid motion

455

since it is as direct evidence for the fact that celestial bodies not only move around the Earth but also around other celestial bodies. The four moons align in a row. This is not particularly surprising, since they more or less move in the so-called ecliptic, which locally appears as a line. The order of their appearance on the line, however, is not trivial at all: Their path curves very closely resemble circles, and since the path circles with radius r1 , r2 , r3 , r4 appear as a straight line, each moon can be “everywhere” in between the extreme positions ±ri . Thus, a case may arise in which Callisto seems to be closest to Jupiter (or even behind the planet) (compare Fig. 10.78). ◂◂◂ ▸▸▸ Planetary gears: plenty of angular momentum A screwdriver is powered by electricity from an unassuming 3.6-Volt battery (Fig. 10.79). A small electric motor with about 3500 revolutions per minute turns the screwdriver’s blade indirectly. The power transmission via gears shall be analyzed.

Fig. 10.79 Left: A screwdriver is powered by a single battery. Middle: The first stage (there is a second stage behind it). Right: The whole gear system as a “tangible” model.

Solution: The shaft of the electric motor propels a small gear with only six teeth (Fig. 10.79 middle). This so-called “sun gear” transfers its rotational momentum to three equilaterally positioned “planetary gears”, whose 19 teeth are not significant but simply “a byproduct”. The planetary gears are dimensioned such that they are in mesh with a fixed outer gear with 48 teeth. This causes the centers of the planet gears to rotate with one eighth (6 : 48) of the shaft’s angular velocity. The centers of the planet gear form a fixed equilateral triangle. Right behind it, in a second stage, there is another 6teethed sun gear. This gear as well propels three planetary gears (also with a translation ratio of 6 : 48). Finally, the connecting triangle between the planetary gears in the second stage is connected to the axis of the screw-

456

Kinematics: Geometry in motion

driver. Rotations of the electric motor thus cause a single rotation of the screw (about 3500/64 = 55 revolutions per minute). This explains the large angular momentum M , because for a constant power P of the motor, the following applies: P = M ⋅ ω (ω is the angular velocity).

Fig. 10.80 Some more planetary gears. Here it is even better to see how small gears mate with larger ones several times.

Planetary gears have many applications in technology, for example in gear manufacturing, cable winches, and bicycle hub gears (Fig. 10.80). In these applications, we can find a variation that is worth highlighting: If the axes of the planetary gears are fixed and the outer gear is allowed to rotate (the photo of the model in Fig. 10.79 was taken at the German Museum in Munich), then the outer gear rotates significantly slower than the shaft. ◂◂◂ ▸▸▸ Involute gears The following paragraph contains a short overview on the theory of gearing. First of all, the angular velocity ratio between two gears of a gear set must remain constant (fundamental law of gearing), making the transmission of power smooth and the speed variation negligible. Furthermore, it is of great advantage when the profile of a gear does not depend on the gear it mates with (Fig. 10.81 and Fig. 10.82). This is achieved by utilizing involute gearing. Here the profile curves are involutes of a circle: For each tooth flank the points of contact (“line of action”) lie on a tangent shared by both base circles. The contact between a pair of gear teeth occurs at a single instantaneous point. Involute gears also work well when a circular pinion gear is mating with a linear rack gear (Fig. 10.82). Fig. 10.83 shows some other gears, probably so-called cycloid gears. ◂◂◂

457

10.4 Trochoid motion

Fig. 10.81 Involute gears

Fig. 10.82 Rack and pinion gear

Fig. 10.83 Cycloid gears

Cycloids (trochoids) at a higher level The trochoid motion can be generalized by letting a third rod rotate at a constant angular velocity about the endpoint of the second rotating rod. This approach produces a third-level cycloid with a much greater number of de-

458

Kinematics: Geometry in motion

grees of freedom, permitting the construction of many new curves. Fig. 10.84 shows two third-level cycloids from this infinite multitude.

Fig. 10.84 Third-level cycloids with the rod lengths 2, 2, 1 and angular velocities with ratio 1 ∶ 3 ∶ 4 (left curve) and 3 ∶ 2 ∶ 4 (right curve).

If k rods rotate, we speak of k th -level cycloids. Fig. 10.84 shows two thirdlevel cycloids. In general, it can be said that any curve can be approximated to any desired level by higher level cycloids.

Fig. 10.85 Relation to Fourier series expansion

Without going into further detail, Fig. 10.85 illustrates how Fourier series expansion may be simulated by the mere consideration of the y-values of a higher-level. With such decompositions, any periodic function graph can be approximated to any desired level.

11

Spatial motions

Planar kinematics is the basis for kinematics on the sphere. In a way, spherical kinematics can be conducted similarly to planar kinematics. In the spherical variant, everything rotates about straight lines through the center of the sphere. Purely spatial motions, however, make these matters much more difficult. In this chapter, both possibilities will be explored on the basis of certain examples. Two general positions of a spatial Cartesian coordinate system can only be transferred into each other by a helical motion (including the special cases of a rotation or a translation). Kinematics often deals with the transmission of motions from one axis to another. If these axes are parallel, then a two-dimensional problem is given. If these axes intersect, then we are dealing with geometry on the sphere. If these axes are skew (as in the image above), then the problem is “truly three-dimensional”. Besides a number of technical applications, we will try to shed light on the motion of the Earth around the Sun, where two rotations with skew axes are performed. To make matters even more complicated, these rotations are only approximately proportional. Important questions arise relating to the theory of the position of the Sun, such as at what angles of elevation the Sun appears during sunrise and at what position on the firmament it can be found at a given date and time. We will learn about the equation of time and become capable of analyzing sundials with a precision of mere minutes. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_11

459

460

Spatial motions

11.1 Motions on the sphere Each motion in space with one fixed point M is a rotation about an axis f through M (see Fig. 11.1). The path curve c of each point P within the moving system lies on a sphere.

Fig. 11.1 The composition of two rotations about intersecting axes

In order to improve our understanding of this relation, let us consider the pedal point N of the normal from P to r. Both P N and M N remain constant in the course of the motion.

Fig. 11.2 Blender (including its enveloping surface): composition of rotations about intersecting axes. On the right: Something comparable; This analogy, no doubt, contributes to a feeling of dizziness that is felt when trying to wrap one’s head around spherical kinematics.

⊕ Remark : The path curves of the blender pictured in Fig. 11.2 are far less interesting than the enveloped surface that is generated by the curved rod. ⊕

Let us focus our attention on spherical motions, where two rotations about intersecting axes r and f (intersecting at M ) are composed. In that situation, we do not even have to prove the following assertion: Two composed rotations can always be replaced by a single rotation.

11.1 Motions on the sphere

461

Spacial motions differ greatly from planar motions. Instead of an instantaneous pole, we find an instantaneous axis a, provided that the transformation is not a pure translation at this moment. In general, each motion behaves instantaneously like a helical motion with a as its axis. Things become simpler if the motion behaves like a rotation at each instant as shall be the case in the following. The new instantaneous axis p lies in the plane spanned by r and f and passes through M (Fig. 11.3 at the center). If the composed rotations are proportional, then the instantaneous axis forms a constant angle with the fixed axis, thus lying on a cone of revolution ∆f with its apex at M . In the moving system, too, the angle enclosed by p and r remains fixed, and thus, p generates a cone of revolution ∆r which always touches ∆f . It can be shown that both cones perform a mutual glide-free rolling. The path curves of single points are called spherical cycloids.

Fig. 11.3 Cone rolling, including path curves (principal views)

Fig. 11.3 shows a very special cone-rolling situation: The axes r and f intersect orthogonally, and both cones have the same aperture.

462

Spatial motions

The following theorems (without proof) are important for many considerations relating to spherical kinematics: First theorem of spherical kinematics: Two positions of a shape that is moved on a sphere can be transferred into each other by a rotation about an axis through the center of the sphere.

At each moment, a fixed system undergoing arbitrary motion on the sphere acts as if it were subject to a well-defined rotation about an instantaneous axis through the center of the sphere. The spherical path normals thus pass through a momentary pole on the sphere. ▸▸▸ The star handle in motion (a rotation about a general axis)

Fig. 11.4 Star handle in motion (Rotation about an arbitrary axis)

The star handle (Fig. 11.4) is an example of a very simple spherical motion. The end points of the three equally long bars move on a sphere with a fixed radius – the bars’ length. The motion itself, however, is a fixed rotation about a likewise fixed (oblique) axis. The endpoints of the rods share their ◂◂◂ path circle! Spherical motion can also occur as relative motion – as the following example demonstrates. ▸▸▸ The Cardan shaft

Fig. 11.5 Cardan shaft (non-uniform transmission)

11.1 Motions on the sphere

463

By using a Cardan shaft, it is possible to transfer rotations about an axis f onto a second, intersecting axis r. Fig. 11.5 demonstrates this technique in a star handle, which is connected to one axis via one fork (in the shape of a half-circle) at f and to another axis at r.

Fig. 11.6 A combination of two Cardan shafts allows a uniform transfer of the rotation.

The transfer of the rotation, however, is not uniform. In a uniform powertrain, this produces a “wobbling” of the driveshaft, which increases in magnitude relative to an increasing axis angle γ. A combination of two Cardan shafts (Fig. 11.6 and Fig. 11.5 on the right) resolves this problem.

Fig. 11.7 A more sophisticated combination of two times two Cardan shafts enables a uniform transfer of the rotation in merely any direction.

Fig. 11.7 shows how two pairs of Cardan shafts can be connected, which then enables uniform rotations from one axis to another skew axis. ◂◂◂

464

Spatial motions

Fig. 11.8 Bevel wheels

The uniform transmission of a rotation to a rotation about an orthogonal axis is a recurring problem in technology. In the simplest case, it can be solved by letting two rubber-coated cones of revolution with aperture angles of 90○ roll on each other, as in Fig. 11.3. If greater forces are involved, then the use of cogwheels will be required. Fig. 11.8 shows a possible solution to this problem. In practice, worm gears are often employed, as in Fig. 7.34. ▸▸▸ A sophisticated ball joint If the axes f and r are positioned at a variable angle and the use of a Cardan shaft is not desired (presumably because the transmission of rotation has to be proportional), then the ball joint pictured in Fig. 11.9 may be employed. This particular ball joint has been the subject of detailed research by Hellmuth Stachel.

Fig. 11.9 An efficient ball joint, which could replace many bevel wheels.

⊕ Remark : Further details can be found at http://www.geometrie.tuwien.ac. at/stachel/dres.pdf ⊕ ◂◂◂

▸▸▸ “Mad House” A (red) circle rotates about a vertical axis. A second (blue) circle hangs horizontally within the first circle and rotates proportionally about this horizontal axis. Within the second circle, a third (black) circle hangs vertically to the horizontal axis of rotation. It also rotates proportionally about this

11.1 Motions on the sphere

465

third axis (Fig. 11.10, see also Fig. 5.94). Which path curves are described by points on these circles?

Fig. 11.10 Compound rotations about intersecting axes are always spherical. The shape on the right, however, is slightly eccentric and possesses no constant gear transmission ratios.

Naturally, each rotation produces circles as path curves of points off the axis. Superimposing the first rotation with a second one about an axis that intersects the first results in spherical path curves, since the distance of each point in the moving system to the common point of the axes is constant. Each point moves on a particular sphere about the intersection of the axes. If the angles of rotation are proportional, then (as in the case of the cone rolling in Fig. 11.3) we get spherical cycloids with top views that are planar cycloids of second or third level (p. 457). Fig. 11.10 on the left illustrates this motion for three equal angular velocities. In Fig. 11.10 at the center, the respective top view is visible. A variant by Maria Walcher is visible on the right. It is, however, slightly eccentric and thus does not resemble an exact spherical motion despite the spheres involved. Due to the absence of propulsion (the outer sphere hangs like a puppet and can be moved in much the same way), the angular velocities are not proportional. Walcher was inspired by the motion of the eyeball. ◂◂◂

Fig. 11.11 On the left: spherically positioned “compass” on a speedboat. On the right: another spherical motion – with appropriate lateral accelerations.

466

Spatial motions

Construction on the sphere We live on a sphere, even though we may not recognize this at first sight: Therefore, we also construct on a sphere whenever we construct on the surface of the Earth. Thus, it might be said that our planar kinematics are actually “slightly spherical”. What happens if we actually let certain simple things happen on the sphere, such as the string construction of an ellipse (Fig. 1.29) or its construction according to de la Hire (Fig. 3.65)?

Fig. 11.12 Spherical conic section: Some planar constructions can be carried over onto the sphere. On the left: string construction. On the right: construction according to de la Hire.

The result is a “spherical ellipse,” or rather a “spherical conic section.” It turns out that it makes no sense to distinguish between an ellipse and a hyperbola on a sphere (as seen in Fig. 11.13 on the left). The spherical parabola, defined as the locus of all points which are equidistant to a given “straight line” (= great circle) and a fixed point, is not an exception (and looks rather like Fig. 11.13 at the center left, where, however, a small circle is touched): All spherical conic sections are intersection curves of the sphere with certain quadratic cones that are concentric with the sphere. (More information can be found in [16].)

Fig. 11.13 Spherical conic sections and intersection curves of quadratic cones and spheres around the apex: It is impossible to make any further type differentiations.

11.1 Motions on the sphere

467

Fig. 11.14 Spherical conic sections and intersection curves of quadratic cones and spheres around the apex: It is impossible to make any further type differentiations.

Fig. 11.15 A combination of two Cardan shafts allows a uniform transfer of the rotation.

468

Spatial motions

11.2 General spatial motion If a system moves in space in any shape or form, then it naturally becomes difficult to imagine. The main theorem of spatial kinematics is applicable here (a proof may be found in [9]). It states that any spatial motion – no matter how complicated – can be approximated at each point by an infinitesimal helical motion about a well-defined instantaneous axis, as mentioned earlier.

Fig. 11.16 A sphere with a variable radius

⊕ Remark : Fig. 11.16 depicts a very interesting and sophisticated “gimmick” – a “sphere with a variable radius.” Due to an ingenious system of joints, the object is flexible in such a way that all points on the rays pass through the center of the circumsphere. ⊕

Two rotations about skew axes

If rotations about skew axes are composed, then certain assertions about path curves and enveloped surfaces may be attempted.

Fig. 11.17 Two composed rotations about skew axes

If the rotations are proportional, then the problem is further simplified. We have already pointed towards the one-sheeted hyperboloid of revolution: By using two hypoid gear s, a rotation about an axis can be converted into a proportional rotation about another axis (Fig. 6.35).

11.2 General spatial motion

469

▸▸▸ An earnest effort on a tiny scale

Fig. 11.18 The inside of a very efficient pencil sharpener: A cylindrical mill rotates about an oblique axis.

Fig. 11.18 shows the complicated inner life of a very efficient pencil sharpener. The axis on which the pencil is centered stays fixed: In contrast to simpler pencil sharpeners, the pencil itself does not undergo any rotation! Instead, a cylindrical mill with a skew axis is rotated and moves around the pencil. First, a crank turns the cylindrical mill by moving along two points of the axis. On the top of the mill, there are gear flanks which force its relatively ◂◂◂ quick self-rotation by means of a fixed, hollow gear. ▸▸▸ The Stewart platform in space In three-dimensional space, robotics allows us to control any motion of a plane by six arms of variable length (Fig. 11.19). The points of these arms lie on a regular three-sided prism.

Fig. 11.19 Triangular platform ABC controlled by six robot arms of variable length with the fixed points L, M , N , and L∗ , M ∗ , N ∗ . On the left: “zero position”. At the center: The triangle was translated horizontally. A rotation about the inscribed axis (about the center of gravity) can easily be done. On the right: This time, the triangle was tilted, and the instantaneous axis of rotation is inscribed (images: Georg Nawratil).

Such platforms are used, among other areas, in flight simulators. Fig. 11.20 shows something similar in an amusement park, where the “platform” consists of a row of seats in which the hapless victims have a chance to get sick for small change. ◂◂◂

470

Spatial motions

Fig. 11.20 An amusement park “3D shaking machine” with arms of fixed length and robot arms of variable length for precise and safe control

Fig. 11.21 Flywheel according to Leonardo da Vinci , and a large-scale modern application. During uniform rotation, the path curves of all points naturally describe circles. Acceleration or deceleration brings about spatial spirals which approximately lie on a torus.

▸▸▸ And yet it moves! Take a cube and cut off the corners, as shown in Fig. 11.22 left (note the orientation). It is not difficult to show that each triangle 123 thus obtained is tangent at a point N to the sphere inscribed in the cube. Now drop the perpendiculars from N to the sides of the triangle and consider the eight blue triangles that result.

Fig. 11.22 A surprisingly flexible (“overclosed”) mechanism by Otto Röschel

11.2 General spatial motion

471

We now proceed as follows: The eight red triangles also define two squares in the bottom and top surfaces of the cube as well as four congruent parallelograms. We now erect prisms of arbitrary but equal height above the defined polygons. We join the prisms with “spherical double hinges”, as shown, for example, in the picture above in the form of circular arcs. Normally, such a multilinkage mechanism is rigid, which means it has no degree of freedom. Because of its particular dimensions, this special mechanism is surprisingly flexible (“overclosed”). It can move with no difficulty until the edges of the prisms collide. The mechanism was discovered by Otto Röschel in 2002 ([15]). ◂◂◂ ▸▸▸ Non-rigid connections The construction in Fig. 11.21 on the right serves a similar purpose as the “3D shaking machine”. During uniform rotations, an equilibrium between centrifugal and gravitational forces is quickly established. Phases of acceleration and deceleration are especially interesting from the perspective of physics due to the pronounced effects of inertia that occur. Once again, it was the proverbial Renaissance Man who already investigated issues of a similar kind. (In the computer simulation pictured in Fig. 11.21 on the left, the corresponding sketches are overlaid transparently.) The blueprint for a flying machine (Fig. 11.23 on the left) provides one further example of Leonardo’s tremendous imagination. From a purely geometric point of view, it is entirely correct and was probably derived from the observation of bat flight.

Fig. 11.23 Flying in the manner of Leonardo da Vinci : In theory, this model works perfectly fine. It can be animated and verified by methods of computer geometry. There is no doubt that its weakest link is the human passenger, who would have no chance of generating the necessary uplift by pulley-induced wingflaps (not to speak of maintaining it). Bats and birds are capable of flight due to their small size, which automatically increases their relative muscle power (see [9]).

◂◂◂ ▸▸▸ “As if it were turned by gears” What happens in the above example on a tiny scale occurs in nature on a tremendous scale: The Earth rotates about an axis of fixed direction while

472

Spatial motions

it also rotates about the Sun. The axis of the latter rotation is skew to the Earth’s axis. For an observer in outer space, the motion of the Earth is akin to the motion of the mill about the pencil. Spatial kinematics at its finest! (For those interested: The Sun itself has a self-rotation, and its midpoint describes an elliptical path about the gravitational center of the entire solar system.) Of course, the motion of the Earth is not caused by gears, but essentially by a constant reaction towards gravitational and centrifugal forces. Gravity is of particular significance in outer space – and this significance is perhaps best exemplified by the observation that due to self-gravity, virtually every solid object with a diameter greater than 500 km is spherical. ◂◂◂

11.3 What is the position of the Sun?

473

11.3 What is the position of the Sun? In this section, we shall employ geometrical methods to illuminate the relative position of the Sun in the course of the calendar year, as well as during a whole solar day. Certain simplifications allow us to get an easy grip on the issue and answer not only every day questions but also several important ones from the field of architecture: • When and where does the Sun rise and set? • At a given day and time, from where does the sunlight come? • How can a wristwatch be used for an exact determination of the cardinal directions on a sunny day? • When is the Sun exactly in the west? As it turns out, the first and the last questions are completely equivalent. For the mathematically inclined readers, the results will be described by approximate equations. The quality of these approximations can be checked by comparing them with astronomical tables.

Does the Sun not rise in the east and set in the west? The Sun famously sets precisely in the west on only two days of the year. During the winter half-year (and in northern latitudes), it disappears somewhere between the south west and the west – during the summer half-year, between the west and the northwest. Let a living room be precisely directed towards the north. At which time of the year, and for how many minutes or hours, is the room illuminated by the morning or evening Sun? This problem leads to precisely the same question. The naive assumption that the Sun stands at exactly 18h “of true apparent time” in the west – in Vienna at about 19h of Central European Summer Time – is revealed to be false. Let us, therefore, get to the bottom of the matter using the methods of descriptive geometry.

First of all, the facts The Earth takes a year (365.24 days) to revolve around the Sun and continuously rotates about an axis of fixed direction, which currently points approximately to the North star. The time for a full revolution is a little less than 24 hours (about 23h 56m ). Four further minutes are required to compensate for the Earth’s rotation about the Sun (“revolution”). The path curve of the Earth is a near-circular ellipse. The relation e ≈ a/60 holds for the great half-axis a and the ellipse’s linear eccentricity e. Along with the axis of the Earth, the normal of the ecliptic (carrier plane of the

474

Spatial motions

ellipse) defines a constant angle ε = 23.44○ . Due to the precession motion (gyroscopic motion) of the Earth, this value changes slightly over the course of the decades. Thus, in older books, this value is sometimes given as 23.50○ . The idealized Earth’s surface is well approximated by a sphere. The flattening at the poles measures only about 1/300 of its radius. A point on the surface can be precisely given by its geographical longitude λ and latitude ϕ (Vienna, for instance, is located at λ = 16.3○ , ϕ = 48.2○ ).

Let us now simplify several things

In order to decrease the difficulty of our problem, let us assume the following – wholly acceptable – simplifications: 1. Time designations generally refer to the apparent time. It is defined such that the Sun reaches its culmination point (highest point on its apparent path on the celestial sphere) at exactly 12h noon. The time difference between the culmination points always varies and does not amount to exactly 24 hours. In order to see the Sun culminate at 12h on each day, we would need to adjust our clocks all the time. The daily errors accumulate, which leads to deviations of about ±15 minutes over the course of weeks. This is caused by Kepler’s second law, the law of planetary motion: The ray from the Sun to the Earth generates equal areas at equal times.

Fig. 11.24 Shadows become continuously more blurry from left to right – the Sun is not point-shaped.

2. Earth’s orbit can be approximated by a circle (the maximum deviation of the path ellipse measures below 1.5% of the circle diameter). 3. The Sun’s rays are parallel due to the Sun’s great distance. In the approximate model, it is, therefore, enough to calculate by using the Sun midpoint. However, it should be kept in mind that despite its distance of ≈ 150 million kilometers, it still appears on our firmament – due to

475

11.3 What is the position of the Sun?

its enormous diameter of ≈ 1.4 million kilometers – at a viewing angle of ≈ 0.5○ . 4. If each month is assumed to be 30 days long (and thus, each year to have 360 days), then the Earth rotates roughly 1○ about the Sun each day. This value, too, is subject to Kepler’s second law, and thus, varies slightly. During its north winter, the Earth has a higher rotational velocity than during summer. On the northern hemisphere, this causes the winter half-year to be about six days shorter than the summer half-year! For observations that only last for a single day, however, this relatively tiny change of position is disregarded. When compared to the actual values (e.g., without the various simplifications), it can be shown that, for latitudes that are not too extreme (ϕ < 52○ ), all values will be correct to a maximum deviation of 4 minutes (though usually not more than 2 minutes). Given an average day length of 12h = 720m , this amounts to a negligible maximal error of about 0.5% – and this even though we have applied several simplifications! a Z

N

ϕ

S h

V

c

N . . . north celestial pole V . . . vernal equinox c . . . celestial equator

sun

Z . . . zenith h . . . horizon Fig. 11.25 The axis through the celestial poles is parallel to the Earth’s axis a and inclined under the elevation angle ϕ.

476

Spatial motions

Two important auxiliary theorems For an observer on the Earth’s surface, the following first auxiliary theorem can be applied: The north celestial pole (≈ North Star) can be found in northern direction at the elevation angle that equals the latitude ϕ (Fig. 11.25). Proof : The normal projection of the Earth’s axis a on the horizontal base plane γ – the sphere’s tangential plane at the vantage point B – points towards the geographic North Pole. The inclination of the axis corresponds to the geographic latitude ϕ of the observer (Fig. 11.26). ⊙

Fig. 11.26 The North Star, around which everything revolves (on the right: Kepler )

From now on, when we – somewhat imprecisely – refer to the “North Star”, we mean the north celestial pole – the point on the firmament that defines the direction of the Earth’s axis. There may not be a prominently visible star at this precise position, but the actual North Star is only offset by about 0.9○ . This star, the α Ursae Minoris (main star of Ursa Minor), is the current North Star. Due to the precession motion of the Earth, the direction of the Earth’s axis continuously changes, and so does the celestial pole. In a few hundred years, another star will assume the function of today’s North Star. The ancient Egyptians even spoke of multiple circumpolar stars, which were visible at the time of the great pyramids (4500 years ago) in northern direction at an elevation angle of ϕ. The auxiliary theorem may even be of some use in daily life. From our perspective, the whole of outer space rotates about the axis through the North Star. All stars, including the Sun, describe circles about this axis. From a heliocentric perspective, due to the daily relative motion of the Earth about the Sun (which is negligible due to its small impact), the direction of the Sun’s rays s stays constant during the course of a day. Geocentrically speaking, we can thus derive a second auxiliary theorem:

477

11.3 What is the position of the Sun?

a

N . . . north celestial pole

n ⊥ π1

V . . . vernal equinox c . . . celestial equator

E

E . . . pole of π1

N

π1

V

S c sun

Fig. 11.27 When investigating Stone Age celestial geometry, we have to take the precession motion of the Earth into account.

The direction of the Sun’s rays s rotates almost uniformly about the Earth’s axis a during the day and in due course generates a cone of revolution Σ with the axis a. The half angle of aperture σ of Σ is independent of the geographic position and varies according to the dates in the interval by 90○ −ε ≤ σ ≤ 90○ +ε (ε = 23.44○ ). ⊕ Remark : In astronomy, we mostly speak of the complementary angle of σ, which is called the “sun declination.” The value of σ changes slightly during the course of 24 hours, but never more than by 0.4○ (close to the equinox). ⊕

Fig. 11.28 illustrates the change of the cone of revolution during the four seasons (summer is on the left, equinox at the center, and winter on the right). The aperture of the cone is, as already indicated, independent of the geographical latitude ϕ. However, the inclination of the cone’s axis (geographical latitude ϕ) significantly affects the inclination angle of the Sun’s rays.

478

Spatial motions

Fig. 11.28 The “sun-cone-of-revolution” at northern latitudes

⊕ Remark : Within the tropics (ϕ = ±23.44○ ), the Sun alternates between north and south at noon. In this area, if σ = 90○ − ϕ, it is precisely vertical at noon (at the zenith). At the moment of the equinox (σ = 90○ ), the cone of revolution “degenerates” to a plane orthogonal to the axis a. On this day, the shadow of a point on the horizontal base plane moves on a straight line. On all other days, the shadow point moves on a cone of revolution. With the exception of the vicinity of the poles, this conic section is always a hyperbola. This situation is particularly transparent at the North Pole and the South Pole, where, during the day, the Sun simply moves about a perpendicular cone axis. For 24 hours, it is located at the same angle of elevation (a maximum of ε). During winter (north winter or south winter), the Sun does not appear at all. ⊕

▸▸▸ The locus of all possible sun positions The Sun may occupy many positions in the sky during the course of the year, but the totality of all these positions covers only a part of the visible sky. If one imagines all cones of revolution with the half angle of aperture σ intersected with a huge sphere centered at the viewer, one gets a set of circles on the sphere which form a sphere layer. This layer is symmetric with respect to the normal plane of the direction of the North Star.

Fig. 11.29 Locus of all sun positions on the equator and on the northern polar circle

All parts of the layer above the base plane (the sphere’s tangent plane at the viewer’s position) belong to positions above the horizon. It is, therefore,

479

11.3 What is the position of the Sun?

possible to derive a lot of information about the length of days from Fig. 11.29 (see also Fig. 11.56). ⊕ Remark : Fig. 11.29 shows the sphere layer on the equator and on the northern polar circle. It is immediately apparent that, on the equator, all days have a duration of 12 hours. Even on the equator, the Sun is only at the zenith twice per year. On the northern polar circle, the sphere layer clearly touches the base plane twice – on the 21st of June (the only 24-hour day) and on the 21st of December (the only polar night). Fig. 11.33 shows a common day-length-diagram. ⊕ ◂◂◂

▸▸▸ Determination of the angle between the Earth’s axis and the sunrays As we have seen, the size of the date-dependent angle σ is important. We now want to determine it by a simple of construction, to an accuracy of half a degree.

Fig. 11.30 Construction of σ

Fig. 11.31 The main orientations of the Earth

Let us imagine the path circle k of the Earth E in the base plane π1 and the Earth’s axis a parallel to the front view plane π2 . The “zero position” of the light ray direction may be reached at the beginning of spring (around the 21st of March) and is assumed to appear as a point in the front view. At any given date – on the 21st of May, for instance – there is a well-defined angle of aperture for the cone of revolution Σ. Let this date be α days after the onset of spring (in this particular example, it is 60 days). The Earth E is then located about α○ after the zero position. ⊕ Remark : For the sake of simplicity, let us now assume all months to be 30 days long, and thereby, kill two birds with one stone: Firstly, we get 360 days in a year so that each day corresponds to one degree. Secondly, the days are “weighted” in accordance with Kepler’s law of equal areas. Our supposedly arbitrary calendar, where February only has 28 days and both July and August have 31, roughly compensates for the differences between the summer and winter half-years. ⊕

According to the terms of descriptive geometry, the half of Σ’s angle aperture equals σ and results from a parallel rotation of the light ray direction s = ES about the Earth’s axis a until an orientation parallel to the front view has

480

Spatial motions

been reached: The axis of rotation is a frontal line, and from this it follows that the circle of rotation of S appears as one of its diameters. The length r of the segment ES appears undistorted in the top view (⇒ E○ ′′ S○ ′′ = E○ ′ S○ ′ = r). ⊕ Remark : Compared to the exact value of σ on the 20th of May, the error measures only about one fourth of a degree, which we shall gladly accept in this case. During the course of the year, this error never exceeds half a degree, and it is usually substantially lower than that. ⊕ ◂◂◂

▸▸▸ Sunrise and sunset Let us now determine the lenght of a day, or equally, the moment of sunrise and sunset for our given date at a location with a geographical latitude of ϕ (for instance ϕ = 48.2○ ). Fig. 11.32 shows how this calculation may proceed in the simplest of terms: The axis a of the cone of revolution Σ is assumed to be perpendicular. The parallel circles of Σ then appear undistorted in top view. The horizontal base plane γ, if set against a, comprises an angle ϕ. It cuts out two points S1 and S2 from an arbitrary parallel circle (such as the one with the unit length for its radius), and these points represent sunrise and sunset. The corresponding circular arcs can be interpreted as the lengths of day and night. By inscribing a 24-hour “clock-face” on the “unit circle”, the points in time corresponding to S1 and S2 can be read off directly.

Fig. 11.32 Sunrise

Fig. 11.33 Lenghts of day on Earth

⊕ Remark : In reference tables, day lengths are usually described as being about 15 minutes longer than their theoretical values. This is because sunrise and sunset are defined such that they correspond to the subjective impression of an observer. Thus, the Sun is already said to rise as soon as the first light rays – and not the center of the Sun – reach the horizon plane. The same is also true for the setting of the Sun. During the transition from the vacuum of outer space, the sunrays are always refracted into the gradually densifying atmosphere towards the perpendicular so that the Sun (which appears to increase in redness as it approaches the horizon because the non-red color components are scattered more strongly) remains visible on the horizon, even though it should, in theory, have already set. ⊕ ◂◂◂

11.3 What is the position of the Sun?

481

▸▸▸ At which angle of elevation does the Sun culminate?

Fig. 11.34 How high does the Sun make it on the 21st of December? By the way, the angle measurement on the left is a relatively simple way to verify some of our conclusions quickly.

From Fig. 11.32, we can immediately conclude the following: The Sun reaches its maximum angle of elevation of 180○ − ϕ − σ at noon. This angle reaches its minimum on the 21st of December. On this day, the Sun on the 50th degree of latitude reaches a mere angle of elevation of 180○ − 50○ − (90○ + 23.44○ ) ≈ 16.5○ (Fig. 11.34). On the same day, it merely touches the horizon on the northern polar circle (ϕ = 90○ − 23, 44○ ≈ 66.5○ ).

⊕ Remark : On the northern polar circle, the Sun rises during its summer solstice to an angle of elevation of 2ε ≈ 47○ . If one considers that the Sun never sets on that day, one can imagine the gargantuan quantities of solar energy which are induced into the Earth. Under ideal conditions (on a clear sky day), this amount is greater than the induced solar energy on the same day in equatorial areas! It stands to reason that an incredible amount of pack ice must thaw on that day – especially on the southern hemisphere. ⊕ ◂◂◂

The incidence of light at a given moment Once we are equipped with the aforementioned knowledge, it should be a small step to determine the direction of light for any given time of any given date. This time, we draw the cone Σ(a; σ), not in a special orientation (a ⊥ π1 ) but adjusted to the direction of the North Star: let the north direction be the y-direction of our coordinate system. Fig. 11.35 shows how the situation in Fig. 11.32 can be restored by employing a side view. In this view, the given time (auxilary point H ′′′ on the light ray s′′′ ) can be inscribed on the clockface and also transferred into front and top view by the rules of descriptive geometry (→ H ′′ ∈ s′′ and H ′ ∈ s′ ). We are already well-equipped to solve the questions raised in Fig. 11.36: From the photo, it is apparent that it must have been sunrise. The geographical latitude of the Northern Tropic is ϕ = 23.5○ . On the 21st of December on the northern hemisphere, σ = 90○ + 23.5○ . A construction analogous to Fig. 11.32

482

Fig. 11.35 Let the geographical latitude, the date, and the time be given: From which direction does the sunlight incide?

Spatial motions

Fig. 11.36 This picture was taken on the morning of December 21st at the Northern Tropic. How late was it, and what was the position of the Sun at midnight?

yields about 7h in the morning for the sunrise. The construction in Fig. 11.35 for midnight shows that the Sun was located precisely at the nadir at the moment the picture was taken – the opposite of the zenith. On the same day in the Southern Tropic, the Sun stands at the zenith (σ = 90○ − 23.5○ ) at noon. It is also apparent from this construction that the Sun stands exactly in the west (or in the east) whenever the y-value of the helping point H disappears. (In the drawing, the western direction is labeled as W .) Let us now imagine the cone Σ rotated by −90○ about the x-axis so that it corresponds to the geographical latitude of ϕ − 90○ . For the new cone, the synchronously rotated point W assumes the role of the point S2 , which marks the moment of sundown. Thus: The Sun stands on a circle of latitude with the geographical latitude of ϕ in the precise east and west whenever it rises or sets on the “complementary circle of latitude” ϕ − 90○ on the other hemisphere (provided that it does the latter at all). ▸▸▸ Where is south? Fig. 11.35 can be read in an interesting way. If we interpret the 24-hour clock-face as a clock, then we notice that its hour hand (corresponding to the central angle ω) is the normal projection of the light direction onto the clock-face, provided that the 12h -marking (central angle 0○ ) points towards the normal projection of the south direction. If we imagine the usual 12-hour clock-face on the clock, then the central angle ω of the current time towards the 12-hour marking is twice as large as on the 24-hour clock-face in Fig. 11.35 (ω = 2ω). The southern direction is, thus, marked by the moment which lies precisely between the current time and 12 o’clock.

11.3 What is the position of the Sun?

483

Thus, by using any analogue watch, the southern direction can be derived from the sunlight in the following way: First, one proceeds according to the commonly known “boy-scout rule”: One imagines the moment S that lies between the current time and the culmination point of the Sun (around 12 o’clock, or 13 o’clock during summer time). We also have to consider the geographical longitude: For each degree of longitude, the culmination point moves by 4 minutes so that on the Greenwich meridian in France or Spain, 60 minutes would have to be added! Neither must we forget the deviation of the culmination point from 12 o’clock caused by Kepler’s law of equal areas (equation of time), which affects the calculation by up to ±15 minutes. Now, we take off our watch and turn it around so that the hour hand points to the Sun. The marked position then points pretty accurately towards the south. For a more exact determination of the south direction, we would now have to tilt the watch: We should be oriented towards the currently determined south and position the hour hand at the time S so that it points in the same direction. Now, we must merely tilt the clock-face towards the body by 90○ −ϕ (in our latitudes about 42○ ) and repeat the procedure. The tilting action yields a slightly modified south direction. The error, without subsequent correction by tilting, is the greater, the earlier in the morning or the later in the evening we make use of the boy-scout rule, or the farther south we are. By this rule alone, the Sun would always be located precisely in the west at ◂◂◂ 6 o’clock p.m.!

Fig. 11.37 A very small and versatile gem. It can be used in a similar way to the boy scout rule, either to determine the south direction (if you know the time) or to find out what time it is (if you know the south direction).

484

Spatial motions

▸▸▸ A tiny and versatile gem on your necklace The gem mainly consists of a refracting semi-sphere placed on a 24-hour time scale. Let us assume you know what time it is. Now try to get the focused sunrays onto the adjacent point on the time scale (you usually have to tilt the “tool”). The letter “S” then already points to the south. If you do not know what time it is, but you know the south direction: Turn southwards and try to get the focus onto the time scale (tilt the tool again). Then you read the (true) time on the time scale. In Fig. 11.37, the focus shows that it is 8 a.m. true solar time. With daylight saving time, you have to add an hour. ◂◂◂

A constant and a varying angular velocity All our previous deliberations referred to the apparent solar time, which is defined as the time when the Sun reaches its culmination point precisely at noon. We now have to consider that the path of the Earth about the Sun is an ellipse, and the Sun’s angular velocity on its path about the Sun is, therefore, not constant. On the other hand, the angular velocity during its rotation about its own axis is not affected: The time for a whole revolution about the Earth’s axis is about 23 hours and 56 minutes.

The equation of time In the remaining four minutes (which would complete the full 24 hours), the Earth rotates one degree more, which causes the Sun’s culmination point to occur at a slightly different time than on the previous day – during these 24 hours, the Earth has moved by another degree about the Sun, but only approximately due to its constantly changing angular velocity. Each day, several seconds of error are added or subtracted, culminating in a deviation of about ±15 minutes.

⊕ Remark : A precise calculation of this phenomenon is very elaborate. There exists no precise equation for it – rather, one always has to fall back on Kepler ’s nonalgebraic equation of time and try to solve it approximately, see [9]. ⊕

▸▸▸ Detective games If we are faced with a picture of a well-known object (such as a building) on which the Sun’s shadows are visible, then we can determine the date and the time at which the picture was taken. The date, however, is dually ambiguous, as we shall soon discover. In order to succeed, we must know the north direction and the geographical latitude of our scene. Actually, we only have to do “reverse engineer” the light ray construction at a given date and time. (Fig. 11.38): Let s be the light ray that is given in a top view and front view. Let us now consider the plane which appears as a line in the top view and contains the Earth’s axis a (points towards the north). In a side view, the geographical latitude ϕ appears undistorted (auxiliary point H ∈ s → H ′′′ ∈ s′′′ → a′′′ ∋ O′′′ ).

11.3 What is the position of the Sun?

485

In a second step, let us rotate the light ray s about a such that it becomes undistorted (H ′′′ → H0 ∈ s0 ). Let us then rotate the projecting path circle of H so that its axis a appears projecting in a fourth view. We have now achieved two things: In the third view, we can see the date-characteristic angle σ, from which we can derive the date by reversing the construction of σ. The angle ω of rotation appears undistorted in the fourth view, which gives us the time (15○ correspond to an hour). From the indication, we can see whether or not the Sun is still largely in the east. The time difference from 12 o’clock is to be subtracted or added accordingly.

Fig. 11.38 The date (σ) and the time (ω) for a given light direction s

The 53th degree of latitude was chosen in this example (Berlin, for instance, lies on it). The construction produces σ ≈ 77○ , ω ≈ 53○ . The angle α is to be determined via Fig. 11.30: In the front view, we draw a cone of revolution with the axis direction towards the North Star, half of the aperture σ, and the base circle of radius r. It is to be fitted into the scene so that its apex E lies on the path circle k and the base circle of the cone includes the Sun S. The top view of E leads to α (α ≈ 34○ ). The situation then unfolds either 34 days after the onset of spring (25th of April) or 34 days before the onset of autumn (19th of August). The angle ω corresponds to about 3.5 hours. This makes the actual time 15 ∶ 30. Both possible dates occur in central Europe during summer time, which means that we need to add another hour. We must not forget the deviation from the 15th degree of longitude, to which central European time refers. Berlin lies about 1.5○ westwards from the reference circle, which produces a further delay of 6 minutes. A public clock which may have accidentally been included in the photograph would indicate about 16 ∶ 36. The clothing of the people in the picture would provide us with further clues about the time of year: If many people are pictured in summer clothes, it would probably have to be the 19th of August. ◂◂◂

486

Spatial motions

▸▸▸ Two comparable and yet slightly different photographs It takes a while to understand why in the photos in Fig. 11.39, the Sun ap-

Fig. 11.39 Same position, same time, same camera data – but different target points. The camera was only rotated horizontally such that the Sun is depicted on the left. Now it seems to be elliptical – and higher!

pears so differently (both in the sky and in the reflection). The pictures were taken at the same time from the same position without changing anything in the camera settings. Still, the Sun seems to be at a higher elevation in the right image. The “Sun disk” also appears much more distorted in the right image. The answer is not trivial. In order to fully understand what is hap-

s Σ π C Fig. 11.40 With respect to the rotating image plane π, the Sun is rotating about the vertical axis with the lens center C. Thus, the adjacent image of the Sun is moving along the section hyperbola s of a cone of revolution Σ and π.

pening, we need, like we do so often, a good geometrical sketch (Fig. 11.40). If we take several photos at the same time, the Sun will always be in the same location on the sky. Now we rotate the camera horizontally about an

11.3 What is the position of the Sun?

487

angle ω, i. e., about the vertical axis through the center C of the lens. With respect to the sensor plane (or an image plane π which is parallel to it), the Sun then rotates about the vertical axis through the angle −ω. The orbit of the Sun during this relative motion is a circle on an upright cone of revolution Σ. It does not actually matter whether the Sun is “infinitely far away” or not, the image of the Sun is always on the intersection hyperbola s of Σ with π. The contour of the Sun becomes more and more elliptical when the Sun is further away from the center of the image. Also, the height of the Sun will be the larger, the further to the left or to the right it appears. ◂◂◂ ▸▸▸ When are we allowed to measure an angle in a perspective image?

Fig. 11.41 Two photos of vertical objects with shadows, taken at noon time. Only one will allow you to measure the altitude of the solar noon.

As we know already (p. 481), the altitude of solar noon varies between 90○ − ϕ−δ and 90○ −ϕ+δ, where ϕ is the latitude of the location and δ ≈ 23, 4○ is the inclination of the Earth’s axis. Fig. 11.41 shows two photos taken at the same location at noon. Even though it might look better, the picture on the left is not good for measuring angles, as opposed to the wide-angle photograph on the right: One can see that both the images and the shadows of the two ski sticks appear parallel (side light with vertical image plane). One can also check that the light rays (drawn in yellow) through the tips of the ski sticks are parallel. Thus, the whole light plane through a stick is parallel to the image plane (sensor), and all angles in this plane appear undistorted. Let us say that the measured angle of the altitude of solar noon is approximately 20○ . Sherlock Holmes would now be able to determine either the date if the latitude of the location was given, or vice versa, determine the latitude if the date was given. ⊕ Remark : The fact that the camera was held in such a way that the sensor plane was kept vertical, made the task easier. Otherwise, we would have to invest a lot of geometrical knowledge and would need more geometrical objects in the environment to arrive at the same result. Fig. 11.42 (a panorama photo that mainly measures angles) would then be helpful. It would probably even be possible to reconstruct the mountain hut and the exact relative position of the photographer. ⊕ ◂◂◂

488

Spatial motions

Fig. 11.42 A panorama photo, taken a few minutes later

The path of the Moon on the firmament ▸▸▸ The path of the Moon in the solar system M0 E0

◂◂◂ full moon

waxing (1/2) M3 E2 new moon

E3 M2

M1 29.5 days = 4 × 7 days 9 hours Sun

E1

E0

waning (1/2) M0 full moon

Fig. 11.43 The Earth moves 29.5 days around the Sun and – in the average – sweeps ≈ 29○ . The moon needs 27.32 days to rotate 360○ about the Earth, but 2.18 more days to compensate the rotation of the Earth.

The interplay of Sun and Moon has been an object of constant fascination for all cultures. Like essentially all planets, the Moon moves on the same path plane as the Earth, give or take periodic fluctuations of ±5.2○ and a period duration of 18.2 years. It may be tempting to conclude that the path of the Moon – just as the paths of the planets – essentially overlaps with that of the Sun. This may approximately be true during the equinox or new moon, but the full moon’s much higher angle of elevation during winter is still noticeable. Whenever one talks to an astronomer about the Moon’s path, one is inevitably met with a smirk and a suggestion that the whole issue is not quite as simple and that it, therefore, has to be calculated with a much greater degree of accuracy. We shall, nevertheless, attempt to solve the problem qualitatively and geometrically.

11.3 What is the position of the Sun?

489

Fig. 11.44 The full moon rises at sunset and disappears at sunrise. Close to the horizon, the two spheres can be “compared” with the size of trees and buildings which is of course misleading.

Fig. 11.45 Whenever the days or nights are at their longest, the path of the full moon deviates considerably from the path of the Sun. The full moon stands very high at the onset of winter.

Let us have a look at Fig. 11.45 on the left: It is north winter – the southern hemisphere is much more strongly illuminated – and we have new moon. Only the dark side of the Moon is visible from the Earth. In the following 24 hours, the Earth rotates about its axis while the Moon always points its same side towards Earth. It takes 4 weeks to rotate about the Earth. When considered from the perspective of the Earth, the sunrays and their reflections from the Moon overcoat the same half cone of revolution. It seems that the new moon, indeed, follows the path of the Sun (see also Fig. 11.26 on the left). The situation is completely different during full moon (Fig. 11.45 on the right): The Moon is now opposite the Sun, and the half cone generated by the reflecting rays is now practically the elongation of the Sun cone. During the self-rotation of the Earth, the full moon rises to the same height that was essentially accomplished by the Sun at the start of summer. This explains why, during long and clear winter nights, the full moon is a considerable source of light from sunrise to sunset. According to the theorem about the Sun’s culminating point on p. 481, the Sun on the 50th circle of latitude is visible at a maximum angle of elevation of 90○ − 50○ + 23.45○ ≈ 63.5○ . If we now apply the maximal deviation of the Moon’s path, as it was in the winter of 2005/06, then we have almost

490

Spatial motions

reached 69○ . Such an angle of elevation is subjectively almost interpreted as “perpendicular”. During the day, however, the Sun moves at a maximum of 90○ − 50○ − 23.45○ ≈ 16.5○ .

On the poles, the Sun is not visible for the winter half of the year. Every few weeks, however, the Moon shows up as the half moon and reaches its culmination point as the full moon at up to 23.45○ . This happens whenever the full moon occurs precisely on the 21st of June or the 21st of December. According to our previous considerations, it should be clear that the paths of Mercury and Venus on the firmament should always be approximate to the path of the Sun to a certain degree (see also [9]): Both planets are significantly closer to the Sun than the Earth and are, thus, to be treated geometrically like the new moon. Mars and Jupiter, however, can “change sides” on the days surrounding the full moon, and their path on the firmament can, thus, significantly deviate from the Sun’s path. ▸▸▸ What is different on the southern hemisphere? Inhabitants of the northern hemisphere unconsciously tend to privilege the northern hemisphere geometrical statements and examples. On the northern hemisphere, the stars are turning counter-clockwise when we look towards the North Star, and clockwise when we look toward the south. What is different on the southern hemisphere? One of the first things a traveler should do when arriving on the southern hemisphere is to sit down in a park and verify whether the shadow of a tree does indeed go “the other way round.” The Sun still rises in the eastern direction and sets in the western direction, but in general, it reaches its culmination point in the north. Due to the fact that our traveler from the northern hemisphere is “standing on their head”, compared to their homeland, the direction of the Sun’s rotation appears inverted. (In space, there is, in fact, no orientation in rotations, because it all depends on the direction from which one is looking towards the rotation axis). On the southern hemisphere, the direction of the Sun’s rotation is inverted, and the Sun moves counterclockwise across the horizon when we intuitively turn towards the north in order to observe it. If we, however, look towards the south by night, the stars rotate clockwise around a fictive point, the south celestial pole (Fig. 11.46). Fig. 11.47 shows how the night sky at the Cape of Good Hope (South Africa) moves clockwise a little more than 90○ within more than 6 hours (≈ 15○ per hour). There is no star around the south celestial pole that could be used for orientation the way the North Star is employed on the northern hemisphere. Therefore, one tries to find the Southern Cross or Crux. It is so popular that it is featured on several flags representing states on the southern hemisphere, including Brazil, Australia, New Zealand, or Papua New Guinea. Once we have made out the constellation, the south celestial pole can be found by elongating the axis of the deltoid by a factor of 4.2 (see Fig. 11.47). ◂◂◂

491

11.3 What is the position of the Sun?

I am looking northwards towards the North Star: The stars rotate ccw.

I am looking southwards towards the southern cross: The stars rotate clockwise.

I am looking southwards towards the Sun: The Sun rotates clockwise.

I am looking northwards towards the Sun: The Sun rotates ccw.

Fig. 11.46 Clockwise or counter-clockwise?

Fig. 11.47 The southern cross rotates clockwise about the south celestial pole (where, unfortunately, no star can be made out with the naked eye). The yellow marking shows how the south celestial pole may be found. The two pictures were taken more or less from the same viewpoint.

▸▸▸ Multiple circuits around Antarctica Although it does not quite tie in with the theory of sun positions, the following example still fits here (and, to some extent, additionally qualifies as an example of a spherical motion):

492

Spatial motions

Fig. 11.48 Antarctic Circumpolar Current (ACC) – on the left: depicted in a comprehensible way; on the right: only readable for people with extremely well-developed spatial imagination.

The Antarctic continent appears completely distorted on maps like the one in Fig. 11.48 on the right. One either needs to apply a stereographic projection from the North Pole or display a “bottom view” (or “top view,” if you are on the southern hemisphere) of the globe. As a matter of fact, this global current flows entirely on a sphere, which means that we need an interactively twistable model of a sphere in order to be able to imagine everything accurately! ◂◂◂

11.4 Minute-precise sundials for identifying the mean time

493

11.4 Minute-precise sundials for identifying the mean time In this section, we shall introduce sundials for the determination of the mean time. Two types function with shadows of curved surfaces on the indicators. Another sundial does its job by means of an intricate mechanism – the sundial introduced by Oliver and Bernhardt, a variation by Riegler , an idea for a sundial by Hofmann and another by Pilkington and Gibbs. All sundials make use of the equation of time and are exact to the minute, given a careful enough construction and a sufficient size. The calculations of the arrows and of the described mechanisms will now be discussed.

True and mean time Sundials used to be instruments for the measurement of time, and today they still exert a great degree of fascination. Their history dates back to antiquity, when the duration between sunrise and sunset was divided into twelve approximately equal parts with the help of sundials. The position of the Sun was projected onto a surface where a grid of date and hour lines was drawn by means of a shadow cast by a rod or by a circular aperture (Fig. 11.49). An hour used to be a variable unit of measurement that was dependent on the time of year – a temporal hour. In the modern division of hours, the duration between the Sun’s two consecutive meridian passes is divided into 24 equal parts. The meridian of a point of observation is (with the exception of the poles) the great circle on the celestial sphere that passes through the zenith, the north point, and the south point of the horizon. The midpoint of the celestial sphere can be assumed at the point of observation due to its “unimaginably great” radius. As will be shown, these lengths of days vary during the course of the year – this is the true local time. Today, a mean time is employed, constituting a uniform unit of time. It is measured most precisely by atomic clocks. In harmony with the revolution of the Earth about the Sun, a second of mean time is defined by the duration period of 133 Cs light. Next to the true time of a location, the mean location time was first observed. The railroad industry required the introduction of time zones and of mean times for greater areas. Central European Time, for instance, is the mean location time for locations at 15○ of eastern longitude. Our summer time corresponds to Eastern European time (30○ eastern longitude). Sundials – truly analogue clocks – measure true local time. We speak of true noon whenever the Sun is precisely in the south. Mean time and true time correspond to each other on four days a year (mid-April, beginning of June, beginning of September, and the end of December). The mean noon deviates

494

Spatial motions

Fig. 11.49 Ancient clock

Fig. 11.50 Tower clock

from true noon during the course of the year by the equation of time, which we shall soon discuss – this can amount to up to 16 minutes.

Simple sundials From the perspective of a location on the Earth’s surface, the sky seems to rotate about a celestial pole. On the northern celestial sphere, the North Star is located at that point at a distance of under one degree. The axis of the firmament’s apparent rotation points towards the celestial pole. It lies in the vertical north-south-plane and is tilted against the horizontal at the angle of the respective geographical latitude ϕ. The axes of many sundials point in that direction (Fig. 11.50).

Fig. 11.51 Date lines . . .

Fig. 11.52 . . . and hour lines

The planar and horizontal trace of the cone (with half aperture σ) overcoated by the light rays through a fixed point is a conic section, a hyperbola in nonpolar regions, and a straight line during equinox (Fig. 11.51). Path curves of this kind are called date lines. If we wish to construct a simple sundial, we must – for the full-hour moments – intersect a pencil of planes with planes of 15○ to 15○ through a straight line parallel to the celestial axis with the carrier surface of our clock-face (Fig. 11.52). The intersection lines are the hour lines: The Earth rotates by 360○ during 24 hours. Equatorial clocks are special sundials with planar, equator-parallel clockfaces or with clock-faces shaped like cylinders of revolution whose generators are parallel to the celestial axis. In both cases, hour lines are distributed evenly.

11.4 Minute-precise sundials for identifying the mean time

495

The equation of time The motion of the Earth about the Sun is complicated. In order to accomplish a sundial that is exact to the minute, we have to work with tables, or better yet, with a computer simulation. The Earth’s precession motion (the rotation of its axis during the course of 26000 years, Fig. 11.27) and the nutation (small disturbances in the precession motion) are not significant for sundials. Fig. 11.53 shows a “caricatured depiction” of the Earth’s positions during the equinoxes and the solstices (see also Fig. 11.27). The precession motion is visualized on the great sphere (the Earth’s axis generates a cone of revolution).

Fig. 11.53 Precession motion

Fig. 11.54 Kepler equation

In order to achieve a computer simulation, we must explore the issue geometrically with a certain foreknowledge in physics. A mere application of Kepler’s laws is possible, but not easy to implement: The path ellipse of the Earth must be parametrized by time, which requires the solution of the transcendental Kepler equation. By using the nomenclature from Fig. 11.54, this equation is given as √ f (α) = α − ε ⋅ sin α − t = 0 with ε = 1 − (b/a)2 , where this time ε is the numerical eccentricity of the ellipse. One would do better to employ the theorem of the conservation of angular momentum, from which Kepler’s laws necessarily derive. From the perspective of differential geometry, the path curve with its physical properties may be deduced from the knowledge of the initial velocity and the corresponding direction of motion. The angular momentum is calculated with respect to the Earth’s axis through the Sun which is orthogonal to the Earth’s path plane. The Earth moves on an elliptical orbit about the Sun, according to the theorem about the conservation of angular momentum (Kepler’s first law). The numerical eccentricity of the path ellipse is rather small (ε=0.017). By the same principle, the Earth must constantly be changing its orbital or angular velocity about the Sun. A diminution of the distance from the Sun leads to a square increase of the angular velocity with respect to the diminution factor (Kepler’s second law: equal times – equal areas). 1. The “physical” component While the Earth moves non-uniformly about the Sun, it also rotates with

496

Spatial motions

a uniform angular velocity about its own axis. This leads to a small daily deviation, until the Sun once again returns to the south. This deviation contributes to the equation of time as the daily difference “real time minus the mean location time.” 2. The “geometrical” component: The equation of time includes another substantial component produced by the tilt of the Earth’s axis. The rotation about the Sun and the self-rotation have mutually oblique axes of rotation. Thus, it is impossible to imagine both rotations in one plane! A circular clock-face whose plane is parallel to the equator plane with a uniform division of hours appears slightly distorted if projected orthogonally on the path plane of the Earth. Thus, in this normal projection, the clock-hand’s shadow on the clock-face does not rotate at uniform angular velocity! Let us assume, for the sake of simplicity, that the Earth rotates about the Sun at a constant daily angular velocity of 1○ . Thus, every single day, an angle of 1○ would have to be compensated on the elliptically distorted hour index in order to reach the Sun’s relative position. The revolution of the shadow on a circular clock would not be uniform! 3. “Equinox line” and path ellipse At both equinoxes, the Earth’s self-shadow boundary passes through both poles. Sunlight incides the Earth’s axis orthogonally. The connecting straight line of both positions on the Earth’s path – the equinox line – encloses an angle with the principal axis of the path ellipse. This angle changes slightly due to the precession motion and the perihelion precession (the rotation of the ellipse apices) – though this change has been negligible during recorded history. It also affects the values of the equation of time, though not to a great degree.

Fig. 11.55 The eight-shaped loop of the equation of time

In Fig. 11.55, the equation of time was solved for the Earth’s data. Each position of the Sun at midday corresponds to a point on the eight-shaped loop. If the angle between the equinox line and the principal axis of the path

11.4 Minute-precise sundials for identifying the mean time

497

ellipse is 90○ , then the eight-shaped loop is axially symmetric. Fig. 11.55 also shows the self-shadow boundaries of the Earth.

Fig. 11.56 Eight-shaped loops on the celestial sphere

Fig. 11.56 shows an image of the celestial sphere on which the stars were projected. The horizon plane for 48○ of northern latitude (Vienna), the zenith Z, the celestial axis, the plane of the local meridian, the celestial equator (double line), and both tropics are all inscribed. The eight-shaped spherical curves for the full hours of mean local time are also visible. They are produced by a rotation of the hour line for the mean midday by a multiple of 15○ . By the way: Computer simulation allows us to solve the equation of time for any location of any planetary system, any numerical eccentricities, and any axial tilts. This produces many varying loop shapes, which may also be symmetric and do not necessarily have to possess a double point.

The Bernhardt sundial

Fig. 11.57 The creation of the curved clock-hand

The 365 sunrays through a fixed point on the Earth throughout all precise middays of the year lie on a cone – a director of this cone is the eight-shaped loop on the celestial sphere derived from the equation of time (“eight-shaped cone”).

498

Spatial motions

Let us now consider a circle in an equator-parallel plane (Fig. 11.57). Its axis passes through the celestial pole. Let us now mark 24 points on the circle separated by 15○ each and label them 0, 1, . . . , 23, 24=0. Let us now inscribe rays towards the eight-shaped loop on the celestial sphere through point 12 for the mean midday. In order to prevent an intersection of this cone with the axis of the circle, point 12 is rotated from its deepest position slightly towards the east (the directions towards the eight-shaped loop are preserved). During the day, a light ray which belongs to the eight-shaped cone through 12 rotates uniformly about the axis of the circle and in due course generally envelops a hyperboloid of revolution1 . The surface of rotation enveloped by the rotating eight-shaped cone (or by all hyperboloids) can be employed as a curved clock-hand of a sundial for mean time. The surface of rotation is the focal surface of the congruence of rays formed by all light rays meeting the circle. The circle itself is a focal curve of this congruence. According to the laws of construction, all light rays which touch the clockhand at mean midday and meet the circle pass through point 12. The equation of time is thus considered. In order to read a zone time on the sundial (instead of local time), the circular hour index is rotated by the difference angle between the respective location’s geographical longitude and that of the zone meridian. The described idea dates back to Oliver in 1892 and was improved by Bernhardt in 1964. The problem that the occurring envelope surface of revolution is composed of two sheets due to its construction from an eight-shaped cone is solved in this sundial by means of two different surfaces of revolution, which are simply swapped at the solstices. Each surface is employed as a clock-hand for a half-year. The boundary areas of the surfaces of revolution are especially critical at the solstices, because the enveloping hyperboloids overlap. At those moments of the year, the time can no longer be read to minute accuracy.

Fig. 11.58 Riegler sundial

Riegler adapted the idea by Oliver (Bernhardt) by rigidly connecting both envelopes of the surface of revolution to the plate of both clock-faces (Fig. 11.58 1 Rolf

Wieland: Equatorial sundials with automatic time compensation. Newsletter 26 and 27 of the workgroup concerning sundials of the Austrian Astronomical Society 2003/04

11.4 Minute-precise sundials for identifying the mean time

499

on the left). The outer sheet is pictured as a grid, the inner as a closed surface. Depending on the half-year in which one reads the time (each running from solstice to solstice), the shadow on the inner sheet or outer sheet is employed for the determination of time (Fig. 11.58 on the right). The shadow of the clock-face pane on the grid of the outer sheet further indicates the respective date.

Cycloid sundial for mean time We received a question online from somebody in the U.S.A. about the existence of a sundial whose shadows on a clock-face parallel to the celestial axis display the mean time by straight hour lines. If date lines and eight-shaped hour lines are drawn on such a plane, the mean time might be read by means of a circular aperture – though this detail was not asked by the questioner. A beautiful sundial that displays real time is described by Fred Sawyer .2 If a circle rolls in a plane on a straight line, then a diameter of the circle envelops a cycloid (Fig. 11.59). A cylinder with a generatrix that is parallel to the celestial axis and touches a hump of a common cycloid in an equator-parallel plane can, thus, serve as the clock-hand for real time if the hour index lies on the apex tangent of the cycloid hump.

Fig. 11.59 Diameter . . .

Fig. 11.60 . . . of cycloids and the consequences

A sundial can be positioned so that the apex tangent is directed from the east towards the west. The true local time between 6 o’clock in the morning to 12 o’clock noon can then be read on one half-tangent. The true local time between 12 o’clock noon to 6 o’clock in the evening can be read from the other half-tangent (Fig. 11.60). The hour points are placed at equal distances. This allows the sundial to be adapted to the real local time of a zone meridian by simple translation of the hour index on its carrier straight line. Now, one of both sunray cones (as they have been considered for the Bernhardt-sundial) are directed as follows: Their tip is moved along the hour scale of the cycloid sundial, its generatrices for the equation of time zero touch the envelope of the cycloid cylinder, and the ray of the equinox retains its declination of 0○ . 2 The

Cycloid Polar Sundial. Compendium, North American Sundial Society, Volume 5, No. 4, pp. 21–24, 1998)

500

Fig. 11.61 Construction and appearance. . .

Spatial motions

Fig. 11.62 . . . according to Hofmann

The result is an envelope (Fig. 11.61, Fig. 11.62) which may be employed as the clock-hand for mean time. Self-intersections occur in the areas near the solstices, as well as near the cusps of the cycloid. A reading of the sundial is especially precise between 7 and 17 o’clock mean time. The intermediate area of the clock-hand does not have to be especially adapted for this reading – in fact, the clock-hand and the clock-face may be connected. Translations of the hour index allow a reading of zone times, especially during summer time. As with the Bernhardt sundial, there are two clock-hand surfaces which are interchanged at the moments of the solstices. The calculation of this sundial was accomplished by using the software Open Geometry. The characteristics of the surface were calculated at uniform intervals by intersecting two adjacent eight-shaped cones – for instance, at one-minute intervals. The surface was, thus, determined by a family of characteristics, and the connecting surface of two neighboring characteristics was interpolated. While the sundial may be visually impressive, its plan for construction may only be provided as the answer to a given initial question. The construction would in any case be very expensive, and the mean times would be better displayed on other sundials.

The Pilkington-Gibbs sundials Another approach to a heliochronometer that is exact to the minute was given in 1906 by Pilkington and Gibbs – Gibbs was the inventor and Pilkington the manufacturer. They equipped a pivotable circular disc so that, in areas outside of the horse latitudes bounded by the tropics, it can be rotated parallel to the equator immediately after it is brought into line (Fig. 11.63). Near the equator, the carrier half-sphere must be positioned along a slope. The circular disk C (gray) that functions as the clock-face of a 24-hour clock can be rotated into itself (Fig. 11.64). An attachment A with a (red) reading mark is fixed to it. A second attachment B (yellow) is also fixed, but in a movable way: It can be restricted towards a circular arc (realized by a slot guide within the disk), whose center is the normal projection of the

11.4 Minute-precise sundials for identifying the mean time

501

reading mark A on the circular disk (see also the exploded-view drawing in Fig. 11.65). Two small drilled holes in the attachment B allow light rays to reach the reading mark. The attachments are dimensioned so that light may enter onto the reading mark through at least one of the two drilled holes regardless of the time of year.

Fig. 11.63 Adjustment of the geographical latitude . . .

Fig. 11.64 . . . and the time

The sundial is adjusted on location to its geographical latitude ϕ. A very simple instruction manual may now be given as follows: One may first adjust the current date on the small (green) wheel D (Fig. 11.64 center, for instance November 4th ) and rotate the circular disk until one of the light rays hits the reading mark (Fig. 11.64 on the right). Now, the exact time may be read on the hour index (in the particular example, it is 09:44 – without the equation of time, it would merely indicate 10:00). If both attachments were diametrical, then the equation of time would be disregarded, but if the circular disk is rotated far enough so that the incident light hits the reading mark, then the displayed time is pretty accurate: The

502

Spatial motions

deviation of each hour from the true midday corresponds to a rotation of the disk by 15○ . In order to take into account the equation of time, the attachment B (with both drilling holes) must be slightly rotated – depending on the date. This occurs, as pictured in the above example, by means of an eccentric dial inside the half-sphere. Both attachments are connected by a rod (straight line). The rod is pressed towards the eccentric disk by a spring. A rotation of this disk causes the rod to be pressed in one or the other direction (Fig. 11.65 to the right).

Fig. 11.65 Exploded-view drawing and the eccentric date dial

The dimensioning of the disk must be calculated so that the rotation angle corresponds to the required position with the corresponding date. This used to be done with the assistance of tables, and can nowadays be calculated by using computers. Given an infinitely thin rod, the profile is the envelope of a family of straight lines – and the actual profile is a curve which is an offset (Fig. 11.65 to the right).

11.5 Kinematics in the animal kingdom

503

11.5 Kinematics in the animal kingdom ▸▸▸ Inverse kinematics

Fig. 11.66 Young cat in action, that uses its tail for counterbalance.

Over thousands of years of evolution, nature has perfected the movement of animals. Be it a small cat that already moves its body perfectly to catch bait (Fig. 11.66) or a dear that, in full speed, jumps through rough terrain (Fig. 11.67).

Fig. 11.67 Leaping dear. Most terrestrial mammals can jump or leap, but some use this form of locomotion more often than others.

There is no doubt that nature has already more or less optimized motion. Otherwise, evolution will find a better solution via mutation, and individuals that exhibit an even better way of moving, will reproduce more frequently and, thus, spread their mutated genes. The question for a computer programmer is: How can such a perfect motion be simulated? One possible solution for the problem is the following: First, gather reference images and/or videos, preferably of exact side and front views (therefore, Fig. 11.68 is not 100% ideal, even though the sequence is quite spectacular). Next, load the model of a skeleton into professional programs that provide modules for inverse kinematics (e. g., the free modeling and animation software Blender ). Ideally, the model should be in a symmetrical resting pose.

504

Spatial motions

Fig. 11.68 Sprinting lion. Cats mostly use their back legs for jumping. The front legs leave the ground before the back legs do.

Next up is the rigging process, where a bone-like structure is created that represents the moveable joints and that will serve as a guideline for the model to follow. After the overall structure is complete and the individual parts of the model are assigned to the joints, inverse kinematic is applied to the limbs and the head. In this way, just one of the joints is positioned by hand and all others further up the joint hierarchy will be calculated by the program automatically. After adding keyframes to the animation, which are snapshots of the joint positions and rotations, they will be interpolated in the final animation to create continuous motion.

Fig. 11.69 Walking cat

The results can be quite spectacular: Fig. 11.69 shows the typical movement of a larger cat. The skeleton was also used to simulate the leopard’s jump in Fig. 3.11 (skeleton source by Florian Croquet https://floriancroquet. ◂◂◂ com/). ▸▸▸ Locomotion in mammals and large birds Even though this is not a book about biology, the geometry explained in this book can facilitate a better understanding of biology. A mammal moves its legs backwards and forwards beneath its body (in contrast to a reptile which has legs that are stuck out to the side). The most common four-

11.5 Kinematics in the animal kingdom

505

legged locomotion is the diagonal walk, being used by most hoofed animals (Fig. 11.70) and their predators (Fig. 11.68)3 . Giraffes and a few other animals, such as brown bears and camels, move both legs on one side together and then both legs on the other side. When they accelerate, there is a moment in each stride when all four legs do not touch the ground anymore (Fig. 11.71).

Fig. 11.70 Running oryx (diagonal)

Fig. 11.71 Running giraffe: Both legs on one side together and then both legs on the other side.

Fig. 11.72 Sprinting ostrich: Outrun predators . . .

3 https://www.earthlife.net/mammals/locomotion-2.html

506

Spatial motions

Running on two legs, like humans or the ostrich (Fig. 11.72), is obviously less complicated (ostriches are among the fastest runners and can easily outrun their predators; it therefore does not pay off to develop “expensive” wings for flying – the wings are only used for steering).

Fig. 11.73 Giraffe running

Fig. 11.74 Sprinting ostrich in a simulation.

The two animation sequences (Fig. 11.73 and Fig. 11.74)4 shall demonstrate how inverse kinematics leads to practically the same results as nature has come up with by itself. It is not surprising, since, in between the given positions, only those poses are calculated that lead to the smoothest and fastest motion. Mathematics – originally a “self-contained microcosm” – is a science that has always been oriented towards nature, and, thus, has “evolved” in a direction that now enables this science to pre-calculate and simulate natural processes. As a final example, Fig. B.44 shows how the locomotion of frog legs (Fig. 11.75) can be simulated by means of a simple kinematic mechanism. The inspira4

Giraffe: https:www.cgtrader.com/3d-models/animals/mammal/realistic-giraffe-skeleton Ostrich: Idaho Virtualization Laboratory (IVL), https://sketchfab.com/ivlpaleontology

11.5 Kinematics in the animal kingdom

507

Fig. 11.75 Frog legs in practice

Fig. 11.76 Frog legs are being moved by a mechanism.

tion for this computer simulation came from a model exhibited in the zoo of Vienna (Schönbrunn). ◂◂◂ ▸▸▸ Gripping, biting, and shredding Fig. 11.77 and Fig. 11.78 show three types of devices for gripping, biting, and shredding, that can be found among arthropods.

Fig. 11.77 A tiny pseudoscorpion (≪ 5 mm). The pedipalps generally consist of an immobile “hand” and “finger”, with a separate movable finger controlled by an adductor muscle.

508

Spatial motions

Fig. 11.78 Mighty mouths: On the left an ant, on the right a tiger beetle

The mandibles of ants are thick at the base and covered in thorns. They can be opened to a degree of slightly over 90○ . The mandibles of tiger beetles (genus Cicindela) differ considerably in form and function. They terminate in dagger-like tips to cage their prey. These mandibles cannot be used as transport devices, but they are a powerful apparatus when it comes to catching, handling, and shredding prey. ◂◂◂ ▸▸▸ Kinematic four-link chain in the monitor lizard head Kinematic chains are frequently found in the animal world. The benefit of this mechanism is, once again, that it enables the animal to move the parts of its jaws against each other like a pair of scissors.

Fig. 11.79 Monitor lizards have a built in four-bar-link.

Such a kinematic chain can be found in the heads of monitor lizards (Fig. 11.79). Note that both jaws open at the same time, since the red bone stays fixed. ◂◂◂ ▸▸▸ How to extend the mouth to a long tube? The sling-jaw wrasse (Epibulus insidiator) has developed a cunning hunting trick: While catching prey, it rapidly extends its mouth into a long tube with which it sucks up small fish.

11.5 Kinematics in the animal kingdom

509

Fig. 11.80 The sling-jaw wrasses ambush their prey with an astonishing kinematic apparatus which contains multiple joints.

Fish estimate the level of danger by a predator’s size, speed, and distance to them. The slingjaw wrasse is a seemingly inconspicuous, and therefore, prey approaches without fear. The underlying kinematic mechanism, which contains multiple joints, is very sensitive due to the length of the movable bone structures. ◂◂◂ ▸▸▸ Unfolding the wings In beetles, the membranous hindwings are folded under heavily chitinized, stiff forewings, the elytra. On the wing blade, beetles have several joints that allow them to fold their wings in a characteristic way.

Fig. 11.81 Wing cases of chock3

Fig. 11.81 shows the different stages of a cockchafer (Melolontha melolontha) unfolding its wings as it launches itself into flight. The elytra are lifted first. Then then membranous wings, which are folded several times, are gradually unfolded. The whole process lasts about half a second. Once the stabilizing joints are fully extended, the wings are absolutely rigid and impervious against aerodynamic forces that occur during flight (Fig. 11.82).

510

Spatial motions

Fig. 11.82 A cockchafer in flight

Fig. 11.83 Wing cases of flower chafers

A distinctive feature of flower chafers (Cetoniidae, Fig. 11.83) or also scarab beetles (Scarabaeidae, Fig. 2.14) is that they do not open their wing cases during flight. Their wings slide out from slots on the beetle’s sides and flap in the open air, while the wing cases remain closed. By not having to lift and position its wing cases, the flower chafer saves time and can launch into flight very rapidly. ◂◂◂

12

A variety of filling patterns

A planar tiling is a gap- and overlap-less coverage of a plane with specially formed panels or tiles. The simplest forms are triangles and quadrangles, which may be regular or irregular. Regular pentagons already cause problems, because a plane cannot be gaplessly covered by such shapes. This is due to the violation of a basic condition: In each apex point, k ngons coincide, which means that the sum of interior angles in the n-gon must be n ⋅ 360○ /k. However, the sum of interior angles of an n-gon equals (n − 2) ⋅ 180○ (which can be proven inductively by decomposing the n-gon into triangles). An equalization yields the condition 1/n + 1/k = 1/2. This is impossible for regular pentagons, as there exists no natural number k for which this condition is met. Nevertheless, there are many possibilities of covering the plane with irregular pentagons. The regular hexagon does not cause such problems – the cells of honeycombs are a classical example of a hexagon tiling. However, this already exhausts all regular n-gons where tilings are possible. There are tilings with only one basic form (monohedral) or with many different basic forms (n-hedral). However, the most important distinction is whether or not the tiling is periodical or non-periodical. Coverage is periodical if there exists a translation in the plane that would move the pattern into itself. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_12

511

512

A variety of filling patterns

12.1 Ornaments and symmetry groups Frieze ornaments Two congruent figures with the same orientation can be brought into alignment through rotation and translation, while two congruent figures with opposite orientations require a reflection or a glide reflection (i.e., a reflection followed by a translation along the axis of reflection).

Fig. 12.1 Seven types of frieze ornaments (singly periodic patterns)

A frieze ornament is a singly periodic pattern whose basic design arises from elementary copies of single primary cell. To create such ornaments, we consider a basic figure (inscribed in a square “fundamental cell”) and subject it to one of these transformations (Fig. 12.1, Fig. 12.2). From the primary cell, an ornament can be created through ● translation along the main direction or a diagonal direction, ● rotations about the midpoint through multiples of 90○ , and ● reflections in both central axes and the two diagonals (Fig. 12.3).

12.1 Ornaments and symmetry groups

513

Let us ignore pure translation along the main direction, which yields a simple, trivial ornament, which is of no particular interest. We can now arrange two or four congruent primary cells, either with the same or opposite orientation, so that a frieze ornament results from repeating this enlarged pattern.

Fig. 12.2 Flowchart for the seven different ornaments created from a primary cell

Fig. 12.3 Two more examples for the seven different ornament that are cerated by a primary “fundamental” cell.

514

A variety of filling patterns

Plane symmetry groups One can attempt to bring some systematization to the not so obvious multiplicity of ways in which the plane can be tiled.

Fig. 12.4

The flowchart shown in Fig. 12.4 allows for the assignment of any tiling to one of the seventeen possibilities shown. In the Alhambra, in Granada, all seventeen patterns appear among the wall tiles, and these were created long before this geometrical classification.

12.2 Periodical tilings

515

12.2 Periodical tilings Regular n-gons as basic building blocks Everybody knows the pattern of honeycombs (Fig. 12.5), which is based on regular hexagons. Since every such hexagon can be subdivided into equilateral triangles, this type of tiling also works with equilateral triangles.

Fig. 12.5 Classic tiling with hexagons (wasps and bees)

It is also possible to tile a floor more trivially, using regular quadrangles (or squares). Other tilings with regular n-gons are impossible. In this case, nature proves to be generous and pragmatic, as it often is (Fig. 12.6). In the left image, the elongated plates on the bottom side of the rattle snake’s neck appear to be considerably shortened. They barely appear to disrupt the planar tiling that is pictured.

Fig. 12.6 On the left: hexagonal tiling (at least on the top side). On the right: Certain modifications can be discerned on the bottom side.

▸▸▸ From shark skin to flow-optimized architecture The arrangement of the scales on the skin of fish and reptiles is of practical importance to these animals. Investigations of shark skin have shown that water undergoes tiny turbulences as it moves across it – an impressive achievement in streamlining.

516

A variety of filling patterns

Fig. 12.7 Analysis and architectural construction of shark skin tiling. The turbulences are produced deliberately for the purpose of ventilation.

At Studio Hadid, Mario Gasser, Peter Schamberger, and Sebastian Gallnbrunner used these insights in architecture – an idea that won them the Austrian construction prize in 2005. ◂◂◂ Inspired by such pictures, one may immediately think of interpreting tilings as projections of spatial manifolds. A software developed for this purpose permits the interactive construction of shapes based on magnetic repulsion which, for instance, may very well be composed of regular pentagons, but which may, nevertheless, diverge into a rhombic structure. Otherwise, the result would always be a pentagondodecahedron (Fig. 12.8).

Fig. 12.8 Left and right: planar “half-regular” shapes which are essentially composed of regular pentagons but which, nevertheless, partially diverge. At the center: Thus, bending allows tilings of surfaces. The left – non-symmetrical – tiling by Franz Gruber seems to be unknown, and the right one was invented by no less a figure than Albrecht Dürer.

▸▸▸ Tiling with paintings An interesting “two-and-a-half-dimensional” tiling based on squares goes back to Robert Lettner: He interprets square paintings as function graphs, and thus, creates artificial “artistic landscapes” (Fig. 12.9). The color does give the tiling an extra dimension. A color value (red-greenblue) is assigned to each point in the plane, which is then somehow translated into a height value. A clever coloring of the corresponding spatial points produces interesting and often unintentional effects. ◂◂◂

517

12.2 Periodical tilings

Fig. 12.9 Tiling with squares

▸▸▸ Alteration of the sides of a basic building block Tiling with squares or rectangles seems to be trivial. By changing border lines, however, it can be varied such that the result is not trivial any more. Fig. 12.11 shows how the sides of the squares of Florentine patterns are replaced by line strips which are centrically similar with respect to the square side.

Fig. 12.10 Simple tilings

Fig. 12.11 Tiling using squares

◂◂◂

Fig. 12.12 Rhombus patterns with 3D effects (see also Fig. 2.16)

Irregular polygons as basic building blocks Every triangle can be used to tile a plane: For any arbitrary triangle, a reflection in a side’s midpoint produces a parallelogram from which entire strips can be built. Such strips, laid next to each other, can cover the entire plane.

518

A variety of filling patterns

Fig. 12.13 Non-trivial tilings using rhombuses, rectangles, and parallelograms

Tiling based on an arbitrary n-gon

Fig. 12.14 No longer trivial, but still somewhat Fig. 12.15 A square and a dodecagon as the simple basic forms

Let an arbitrary quadrangle be reflected in a side’s midpoint. Now arrange the quadrangle and the reflected quadrangle alternatingly side by side (Fig. 12.10) to produce a strip. Multiple such strips can be seamlessly arranged (this is best visualized by a color labelling of the quadrangle’s interior angles). This method also works for non-convex quadrangles (Fig. 12.10 bottom left). A special case is a rhombus made up of two equilateral triangles. With such a rhombus, we can produce beautiful patterns, like one that looks like stacked cubes (for instance, in the Basilica di Santa Prassede in Rome). Tiling with an arbitrary pentagon Fourteen types of convex pentagons that tile the plane are known today, and they were all discovered from 1918 to 1985. However, there may still be

519

12.2 Periodical tilings

further undiscovered variants of convex tiling pentagons – it has not been proven that the search is complete.

Fig. 12.16 Tiling with convex . . .

Fig. 12.17 . . . and non-convex pentagons

Another way of classifying irregular tiling pentagons is one in which side lengths are kept constant (convex and concave pentagons). Fig. 12.17 shows instructions by Walter Jank on how to best pack skiing boots into the trunk of a car, provided that the trunk is large enough. Tiling with an arbitrary hexagon

Fig. 12.18

Three types of irregular convex tiling hexagons are known today. Fig. 12.19 shows a tessellation instruction which leads to irregular convex hexagons.

520

A variety of filling patterns

Fig. 12.19 Irregular hexagons

It is impossible to find tilings with n-gons, where n ≥ 7 based on a single basic form (a proof can be found in Reimann: Tilings, geometrically considered, in “Mathematical Mosaic”, Cologne 1977).

Periodical tilings with multiple basic forms

Fig. 12.20 Archimedean tiling with regular hexagons, equilateral triangles and squares

If all utilized basic forms are regular, one speaks of a semi-regular or Archimedean tiling.

Fig. 12.21 Archimedean tilings: regular hexagon and equilateral triangle (to the left), regular dodecagon and equilateral triangle (to the right)

12.2 Periodical tilings

521

There are several different types: Square and equilateral triangle (two variants), square and regular octagon (to be seen in Fig. 12.22), regular hexagon and equilateral triangle (two variants, one to be seen in Fig. 12.21 to the left), a triplet of regular hexagon, equilateral triangle and square (Fig. 12.20), regular dodecagon and square, and finally, regular hexagon, regular dodecagon and equilateral triangle (Fig. 12.21 to the right).

Fig. 12.22 Two congruent Archimedean tilings are “connected” via symmetric polyhedra.

Fig. 12.22 and Fig. 12.23 show a spatial interpretation of the “connection” of two Archimedian tilings by means of congruent truncated frustums (these shapes belong to the so-called scutoids, see https://en.wikipedia.org/ wiki/Scutoid). In Fig. 12.23, the three-dimensional scene is viewed from above, again showing an interesting tiling which this time consists out of squares and non-regular symmetric hexagons.

Fig. 12.23 Continuation of the above image; to the right a top view is displayed, revealing another tiling with squares and hexagons.

522

A variety of filling patterns

12.3 Non-periodical tilings We can distinguish between two types of non-periodical tilings: Aperiodical tilings, where the basic forms are suited for periodical as well as nonperiodical tilings, and quasi-periodical tilings, whose basic form is only suited for non-periodical tilings (and then only if it adheres to certain rules).

Self-similar aperiodical tilings If many instances of a basic form can be fitted together so that an enlarged version of the basic form is produced, we speak of inflation. The inversion of this procedure – the decomposition of a form into scaled-down but otherwise equal versions – is called deflation. This pattern may then repeat itself at multiple scales, which is called self-similarity or scale invariance.

Fig. 12.24 Chair tiling

Some examples include the chair tiling (Fig. 12.24) or the Sphinx pattern (Fig. 12.25). From a single initial figure, the pattern is constructed by repeated deflation. The aperiodicity of the Sphinx pattern is caused by the greater form being composed of many mirrored and unmirrored smaller forms.

Central aperiodical tiling Certain basic figures can be arranged radially, or as a spiral, about a center. The resulting tiling is non-periodical. A simple example is an equilateral triangle with an angle of 30○ at the tip. It is then positioned 12 times about

523

12.3 Non-periodical tilings

Fig. 12.25 Sphinx pattern

a center where the tips are located, and it may, thus, be continued radially. If this pattern is cut into two halves and translated by one or many steps, then a spirally arranged aperiodical tiling from equilateral triangles is created. The legs of the triangle can be replaced by congruent polygonal strips, which produces an infinite amount of central tilings.

Quasiperiodical tilings Each periodical tiling possesses a basic form comprising a finite number of elements from which the whole may be patterned: but do quasiperiodical tilings also have a basic form? In 1966, Robert Berger proved that there exists a finite number of basic elements which can tile the Euclidean plane only non-periodically. Berger, thus, embarked on a search and first found a set of 20426 generating elements for a quasiperiodical tiling. This number was greatly diminished in the following years until finally, in 1973, Roger Penrose came upon a quasiperiodical tiling that is based on only two elements. One of these pairs of generators is renowned for its shapeliness and is known as kite and dart. Another pair of generators is given by two rhombuses with equal side lengths. The thin rhombus has an interior angle of 36○ and 144○ – the thick rhombus is likewise defined by 72○ and 108○ . Tilings of this type are called Penrose patterns.

Fig. 12.26 Penrose patterns

The secret behind Penrose’s pair of generators lies in the golden ratio. The kite and the dart are created from a rhombus with the angles 72○ and 108○

524

A variety of filling patterns

√ by subdividing the main diagonal at a ratio of Φ ∶ 1, Φ ∶= (1 + 5)/2 and connecting the subdivision point to the blunt vertices. Then, all sides of the kite have either a length of Φ or 1. If the respective edges of both shapes are connected by two circular arcs with the radii 1/Φ (orange) and 1 (yellow) for the kite and the radii 1/Φ (yellow) and 1/Φ2 (orange) for the dart (Fig. 12.27), then the following rule has to be obeyed during the construction of a quasiperiodical tiling: Adjacent edges have to connect circular arcs of the same color.

Fig. 12.27 Inflationary kite

Penrose patterns may also be created by deflation or inflation (see Fig. 12.26, Fig. 12.27, Fig. 12.28): A kite deflates into two small kites and a small dart: 1K → 2K + 1D. A dart deflates into a small kite and a small dart: 1D → 1K + 1D. (The inversion of this procedure is inflation.) In matrix notation, we have K D 2, 1 ( )→M ∗( ), where M = ( ) D P 1, 1 Thus, the iteration of this process yields M n = (

is the n-th Fibonacci number.

f2n+1 f2n ), where fn f2n , f2n−1

1 1 ) → M n ⋅( ) = 0 0 (f2n+1 , f2n ), then the ratio of the number of kites to the number of darts converges against Φ. If an entire plane is completely covered, this ratio is irrational. This is impossible for periodical patterns – and the quasi-periodicity of the Penrose patterns directly follows from that observation.

If one starts with a kite shape and deflates it n times, or (

It can be shown that there exists an uncountable number of Penrose patterns made of kites and darts! The same holds true for all other Penrose patterns, which, nevertheless, have the following bizarre characteristic: All patterns are locally isomorphic: Each neighborhood of a pattern is also present at an infinite number of other places! How far away are the copies of a Penrose pattern’s finite neighborhood? The answer to this question is also surprising: If a circular neighborhood with a diameter of d is considered, then the distance between the boundary of the neighborhood and its next exact copy is never farther away than d ⋅ Φ3 /2 ∼ 2.12 ⋅ d.

525

12.3 Non-periodical tilings

Fig. 12.28 Inflationary rhombuses

A connection to physics: Up until 1984, only two forms of solid matter were known – amorphous solid bodies and periodically ordered crystals. However, in the same year Dan Shechtman and his colleagues discovered a quasiperiodical crystal formation in an aluminum-manganese alloy! Several hundreds of such alloys are known today, and this third form of solid matter is now known as a quasicrystal. The above-described Penrose pattern can be seen as a model for “two-dimensional” quasicrystals if we imagine a crystal through periodically layered Penrose planes. The great surprise of Shechtman’s discovery was that until then, a crystal was known as a solid body constructed from a periodically repeated initial cell, but this conception turned out to be too narrow. Now, a crystal does not merely have to exhibit 2-, 3-, 4-, or 6-fold rotational symmetry, but also has to possess a discrete diffraction diagram (X-ray spectrum) with sharp reflections. It may also, for instance, exhibit 5-fold rotational symmetry, which is the case with Penrose patterns. There exist many other tilings that permit the construction of quasisperiodical structures (e.g., the Ammann grid, octagon patterns, etc.). With these patterns, real solid bodies may be modeled, and questions concerning the stable arrangement of the atoms into these crystal symmetries may be researched. ▸▸▸ Semi-regular pentagons

Fig. 12.29 Semi-regular pentagons and tiling with pentagons and semi-regular pentagons

526

A variety of filling patterns

In his paper Semi-regular figures between beauty and regularity ([26]) Hans Walser defines a “semi-regular pentagon” as follows: When a rhombus is cut off a regular pentagon (Fig. 12.29), the leftover will be a semi-regular pentagon. Using this new element as tile, Walser builds various ornaments, tilings (Fig. 12.30), crystallographic patterns, and spirals (Fig. 12.31).

Fig. 12.30 More tilings with semi-regular pentagons

Fig. 12.31 Concentric rings and spirals

Inspired by this work, Franz Gruber subsequently created Fig. 12.32 and Fig. 12.33.

Fig. 12.32 Fivefold rotational symmetry

The combination of regular and semi-regular pentagons proved to be a “fruitful” source for new types of patterns. ◂◂◂

12.3 Non-periodical tilings

527

Fig. 12.33 Iterations with an increasing number of regular and semi-regular pentagons

▸▸▸ Semi-regular dodecahedrons Walser took the next step and generalized the idea into 3-space. He defined a semi-regular non-convex dodecahedron.

Fig. 12.34 Iterations with more and more regular and semi-regular pentagons

The regular dodecahedron may be seen as a compound of a cube with a hip roof on every face (Fig. 12.34, upper left). When the cube has a side length 1 a singular hip roof has a roof length a = 1/ϕ and a roof height a/2 (where ϕ = 1.61828 . . . is the golden ratio). The semi-regular dodecahedron remains when we cut off such a hip roof at every side of the cube. Walser describes these related construction principles as follows: The regular dodecahedron is positive, the semi-regular dodecahedron negative. The hip roof excess of the regular dodecahedron corresponds to the hip roof deficit of the semi-regular dodecahedron. Because of the relative situation between the two dodecahedra

528

A variety of filling patterns

the regular dodecahedron can sit on the semi-regular dodecahedron like the egg on an egg cup (Fig. 12.34, second from the left).

Fig. 12.35 Regular and semi-regular dodecahedrons

Fig. 12.36 The space is filled by putting regular and semi-regular dodecahedrons together.

Since the cube is a “space filler”, the regular and the semi-regular dodecahedron together can fill the space without gaps or overlapping.

Fig. 12.37 What you can create from a cube with positive and negative hips: rhombic dodecahedron, regular pentagondodecahedron, cube, semi-regular dodecahedron and great stellated dodecahedron.

Fig. 12.37 shows all the possible outcomes, if the hip roof’s planes are at varying inclination. Besides the cube the rhombic dodecahedron is also a “space filler”! ◂◂◂

12.3 Non-periodical tilings

529

▸▸▸ Filling the gaps with scutoids Fig. 12.38 and Fig. 12.39 show the “connection” between two aperiodic tilings by means of scutoids (p. 521).

Fig. 12.38 Two aperiodic tilings are connected by means of scutoids. Note that the single scutoids need not have planar faces: If two connected sides of the generating polygons are not parallel, the face is a hyperbolic paraboloid.

Fig. 12.39 Same arrangement as above, different only because of the changed distance between the carrier planes.

Per definition, a scutoid has two parallel boundary polygons, and the vertices of those two polygons are joined by either a curve or a Y-shaped connection. In contrary to prisms, frustums and prismatoids, a scutoid has at least one vertex between the two parallel boundary planes. The name “scutoid” was coined by the authors of https://www.nature.com/articles/ s41467-018-05376-1.epdf, who claim that “scutoids are a geometrical solution to threedimensional packing of epithelia”. ◂◂◂

530

A variety of filling patterns

12.4 Non-Euclidean tilings Several models of the hyperbolic plane exist, such as the Poincaré disk model and the Poincaré half-space model. Let us choose the disk model here, which has the advantage that measuring hyperbolic angles is equivalent to measuring Euclidean angles. However, the metric is altogether different: Distances steadily increase towards the boundary of the circle. The circular edge itself is the set of all infinitely far-away points (horizon). The disk is produced by stereographic projection of the sphere model into the hyperbolic plane (Fig. 1.56). Axiomatically, the hyperbolic plane differs from the Euclidean plane in that there exists an infinite number of parallels to a straight line through a point which does not lie on it. Another characterization may be given based on the property that the sum of interior angles of any triangle is less than 180○ . In the disk model, straight lines (the shortest distance between two points) are circles which intersect the horizon orthogonally. The circles may look like circles – however, the circle midpoint is generally not at the (Euclidean) center. Equilateral polygons (bounded by orthogonal arcs) do not appear to be equilateral, but are, instead, distorted due to a motion in the Poincaré disk.

Fig. 12.40 Hyperbolical tilings by Jos Leys (www.josleys.com)

Which tilings with regular n-gons are possible? Contrary to the situation in the Euclidean plane, the sum of angles of an n-gon is not equal to but smaller than (n − 2) ⋅ 180○ . If k is the number of n-gons adjacent to a vertex, then the following must be true for a regular tiling with n-gons: n ⋅ 360/k < (n − 2) ⋅ 180 or 1/n + 1/k < 1/2. This is given for all n ≥ 3 with an appropriate k, which means that there is an infinite number of regular tilings in the hyperbolic plane. For each regular n-gon, there is also a minimal value of k: (n, kmin ) = (3, 7), (4, 5), (5, 4), (6, 4), (7, 3), and (n, 3) for each n > 7. Fig. 12.40 and Fig. 12.41 show beautiful tilings of the hyperbolic plane. The figure in Fig. 12.41 is defined by Bézier curves.

12.4 Non-Euclidean tilings

531

Fig. 12.41 Hyperbolic tilings with a swordfish by Johannes Wallner

What is the situation on the sphere? Let us remember that tiling a sphere is, indeed, possible in certain special cases. It primarily applies to the Platonic solids, see application p. 140. ▸▸▸ From a dodecahedron to an original and easily manufacturable lamp Fig. 12.42 shows a remarkable patent (probably from the Asian region – though the patent owner is unknown) inspired by such a tiling.

Fig. 12.42 Tiling of the sphere produces an aesthetically pleasing lamp.

In order to understand the issue, we must first abstract it. Let us consider a regular dodecahedron and subdivide the faces, as in Fig. 12.43, into five equilateral triangles. Pairs of triangles connected by a dodecahedron edge form an “skew rhombus,” which is easy to manufacture. The 5 × 12 = 60 equilateral triangles are thus converted into 60/2 = 30 congruent rhombuses. All that is now required is a bit of imagination in order to make the rhombuses ◂◂◂ attach to each other (Fig. 12.42 at the center) – and we are done! ▸▸▸ Puzzles in space The toy industry has also undertaken geometric deliberations and invented puzzle games which produce spheres. The fact that the building blocks are similar but not quite congruent lies at the heart of any good puzzle game. Take the triangulation of a sphere, as in application p. 140, combine two

532

A variety of filling patterns

Fig. 12.43 From a dodecahedron to tiling with triangles and “skew rhombuses.” It was also the basis of patents describing a novel football and an original lamp.

triangles into skew quadrangles, and then construct an entire puzzle using this approach.

Fig. 12.44 Tiling a sphere with nearly-congruent puzzle pieces is quite a challenge.

⊕ Remark : To simplify matters for the frustrated player, the manufacturer provided a cylinder model of the result, which is composed of a rectangular strip and two circular caps in its developed form (see Fig. 12.44 on the right). ⊕ ◂◂◂

13 The nature of geometry and the geometry of nature

The title’s wordplay is perhaps an indication of this chapter’s intentions – namely, to bridge the gap between nature and geometry. It is well-known that many of the surfaces or solids described by geometry can be found in nature, in both the macrocosm and the microcosm. The following question arises: Is geometry a mere “plagiarism” of nature, or has it developed independently, with coincidental parallels to the results of evolution? Geometry helps us to understand, for example, why Platonic solids are “obvious” solutions to many problems in nature and that if certain conditions are given (such as regularity or symmetry), no other solutions actually exist. Nature usually produces regularity or symmetry if an equilibrium of forces or an optimal packing surface is sought. Evolution finds optimal forms on its own. More than two thousand years ago, the ancient Greeks Plato and Archimedes could not have known that “their” solids are so frequently found on a molecular scale. Pythagoras, on the other hand, defined music by means of proportions. Therefore, it is no wonder that musical rules can be beautifully visualized geometrically. Another valid question may be: Is music, as defined by Pythagoras, rooted in “natural phenomena”? Stanislaw Ulam [21] calls mathematics a self-contained microcosm which nevertheless possesses a strong capability of capturing and modeling not only any kind of thought process but perhaps the entire scientific process. To some degree, this probably also applies to geometry as it is a subdiscipline of mathematics. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_13

533

534

The nature of geometry and the geometry of nature

13.1 Basic geometric forms in nature We have already seen it throughout this book: Nature is full of certain basic forms. They are sometimes immediately apparent, as in snail shells, and at other times rather “imprecise”. Although we may not have an immediate answer for every case, we shall nevertheless attempt to get to the bottom of these issues.

Symmetry

Fig. 13.1 Antennae of a moth, a mosquito, and a beetle (all males)

In nature, symmetry is an essential design element. Biologists refer to bilateral symmetry when describing the regular arrangement of the parts of an organism – but only if it is symmetric with respect to a central plane (Fig. 13.1).

Fig. 13.2 Left: radial symmetry; right: only supposedly radial

If certain parts are arranged about an axis, then biologists speak of radial symmetry (Fig. 13.2). This way, the animal kingdom can be subdivided into Radiata (jellyfish, starfish, radiolaria, etc.) and Bilateria (bilaterally symmetric classes of animals). In the kingdom of plants, blossoms exhibit radial symmetry (Fig. 13.17) much more often than bilateral symmetry (Fig. 13.3).

13.1 Basic geometric forms in nature

535

Fig. 13.3 Simple symmetry in the kingdom of plants

Fig. 13.4 shows the imitation of a bilaterally symmetrical plant by a tropical orb-weaver spider – a tactic that serves to attract insects (on the left: view from above, on the right: view from below).

Fig. 13.4 Simple symmetry in the animal kingdom

Circles as distance curves and path curves We have already explained that the most elementary and simplest curve in nature is not the straight line (which, indeed, almost never occurs in life forms) but the circle. These shapes are especially noticeable in the way waves spread. If we attempt to venture into the desert without being armed with either a compass or ancient Bedouin tricks, we will inevitably end up running in circles. One reason for this is that the length of our left step is never exactly equal to the right one; another one is our inability to take into account minute changes to the Sun’s position without making mistakes (ants and bees have this capability, which has been proven by many interesting experiments). When a wasp cuts a circular hole into a leaf (Fig. 13.5), it applies its jaws at constant angles (analogous to a piece of ham being cut on the breakfast table). Described more precisely, the jaws are always orthogonal to a pencil of rays through the center of the circle. The circle is naturally the orthogonal trajectory of this pencil of rays.

536

The nature of geometry and the geometry of nature

Fig. 13.5 The crime and the “culprit”. . .

The wasp does not seem to follow this pencil of rays, which – after all – only exists in theory. It repeatedly cuts short segments of constant length into the leaf. These segments form an angle of slightly less than 90○ to the moving direction, and the procedure is repeated until the wasp reaches its starting point. Thus, it does not actually cut out a circle, but a regular polygon with so many vertices that it can hardly be distinguished from a circle. Both the journey in the desert and the cutting of the hole produce circles by a combination of motion and “work angle”. Circles are also distance curves: All points are equidistant from a center.

Fig. 13.6 The “building of a fortress” by a tiny crab in tidal times

This must be how the wonderful ring-like constructions of the tiny carcinus maenas (Fig. 13.6) are produced. The animal rolls the excavated sand (which contains its food) into balls and moves it some steps away from the center. Once a single ring is finished, another concentric ring is made. This tedious work is all undone when the next tide sweeps it away. When plants such as the circular lichen grow on the surface of a stone, it makes sense that they should try to “augment mass” at their outer boundary. If this happens regularly, then circular contours are automatically produced (Fig. 13.7, Fig. 13.8). The speed at which this lichen grows is not important for the geometrical principle. For a layperson, it would be difficult to detect whether the lichen

13.1 Basic geometric forms in nature

537

Fig. 13.7 Linear growth (I)

Fig. 13.8 Linear growth (II)

stops expanding every few years. This is far easier to detect in trees: The tree produces new layers around the central trunk (Fig. 13.7). The coloring or the hardness of the cross-section suggests that, while this growth is periodical, it does not proceed at the same rate throughout the year. In tropical woods, these tree rings are not as pronounced, because the growth is more regular than in colder latitudes. Although the tree’s increase in thickness is more or less linear, it has no influence on the form of the cross-section.

Spheres and other convex basic forms The circles in the plane correspond to spheres in three-dimensional space. If the carrier medium permits it, then the waves or impulses always expand spherically. Natural objects (whether living or dead) also tend to expand spherically at first, but a change in strategy usually occurs after an initial growth phase. The reasons for this are manifold, though one particularly important reason may be the following: The surface of a sphere increases at a square of its radius, which is why for sonic strength or brightness, for instance, decrease by the square of the distance. However, the volume that is included inside the spherical surface increases cubically with the radius. If a sphere has reached twice its initial radius, then its volume, as well as its mass, has increased eightfold, whereas its surface has only increased fourfold.

538

The nature of geometry and the geometry of nature

Minimal and maximal packets

Fig. 13.9 Half-spherical water droplets

The water droplets in Fig. 13.9 are forced into a spherical shape by the surface tension of the water (cohesion), in opposition to the rules of gravity, it would seem. In order for such a droplet to remain on the leaf, the contact surface with the leaf should be as large as possible. This makes it possible for adhesion to balance out the gravitational pull. This aforementioned subtle equilibrium only works up to a certain scale. At some point, either cohesion or adhesion are too small to “counteract” the increasing mass.

A maximum of food for the offspring. . .

Fig. 13.10 Oval insect eggs (egg-shaped ellipsoids of revolution)

The shape of insect or bird eggs is interesting from a geometrical perspective. Without going too much into detail, it may be said that bird eggs are neither spherical nor ellipsoidal – we know this not least because of our daily breakfast experience. The insect eggs in Fig. 13.10 are most likely not entirely perfect geometrical surfaces either, though they do seem to approximate spheres and ellipsoids of revolution much better than their chicken counterparts.

13.1 Basic geometric forms in nature

539

Fig. 13.11 Ants love their plant lice.

⊕ Remark : The “cute” ladybird in Fig. 13.10 on the left is, interestingly enough, almost shaped like half an ellipsoid. It is thereby optimally protected against agitated ants, which tend to protect “their” herds of aphides – from which they extract a valuable sugary syrup – with great ferocity (Fig. 13.11). Plant lice are a favorite dish of the ladybird and its larvae. ⊕

Don’t roll away!

The reason why eggs have a peculiar shape is to make sure that they contain a maximum of food for the offspring in the smallest amount of space. Bird eggs have the additional difficulty that they tend to roll out of their nests, whereas insect eggs mostly stick to one spot.

Fig. 13.12 “Laboratory experiment”: An egg is rolled on a wooden floor (“short distance”).

In order to minimize this effect, nature simply deviates from the spherical form, and thus, eggs simply wobble around – if they move at all. Fig. 13.12 shows an experiment in which the rolling behavior of a chicken egg with an angular momentum is tested. It is clearly visible that the egg moves in a very specific swerving motion, which may prevent it from rolling too far away. (However, this also has to do with the fluid contents of the egg).

Unrolling and development As we have already seen, developable surfaces play a big role in technology, being so easy to manufacture. Whenever nature “goes to work” on leaves or blossoms, they are usually unrolled which is the geometrical equivalent to a development.

540

The nature of geometry and the geometry of nature

Fig. 13.13 The many phases in the growth of a blossom (I)

Fig. 13.14 The many phases in the growth of a blossom (II)

The process of unrolling often happens over a longer period of time. In the meantime, the leaf may slightly alter its shape before partially hardening. Thus, the result is not necessarily a developable surface anymore. The many phases in the growth of a blossom in Fig. 13.13 and 13.14 show this quite well.

Fig. 13.15 On the left: The cross-section of a dried willow branch, on the right: coral colony

13.2 Evolution and geometry

541

13.2 Evolution and geometry We have previously touched on the geometry of bird eggs. However, how do birds “know” that non-spherical eggs are better for their offspring (assuming that spherical eggs roll away more often, and thus, break more frequently)? If a bird were to lay spherical eggs in inclined or otherwise unstable circumstances, then it might discover that an elliptical form would be more practical if only the animal had the mental capacity for this analysis. If it had that capacity and could somehow affect the shapes of its own eggs, it would certainly do so in the next attempt. While the individual may be incapable of such a feat, the species as a whole is able to surmount this challenge given evolutionary timescales. Evolution is as ingenious as it is simple. We must now deviate slightly from the main topic of this book – for a good reason, as a solid understanding of evolutionary principles is essential for the section that follows. Biologists are hereby asked for their indulgence with regard to my generalizations, but since evolutionary thinking does not yet enjoy widespread awareness, even 150 years after its landmark introduction, and is even the target of some hostility, an attempt to clarify some of the basic issues cannot hurt.

Mutation We shall first and foremost consider the principle of “inexact replication” (mutation): No animal in nature produces offspring that are completely identical to itself, and no lifeform produces identical offspring all the time. This may in part be influenced by the physical difficulty of “repeating” a complicated genetic code without any error. (As a point of comparison, one may try to memorize the first 250 decimal places of π.) The act of exact replication is further complicated by the varying states of the environment where such copying takes place. However, it stands to reason that even perfectly identical laboratory conditions would, sooner or later, be host to imprecise copying procedures. The ancestors of reptiles and birds may at some point have “started” the colonization of land with eggs that were spherical, like those of fish. If that was the case, then many of these eggs must have rolled away and were probably destroyed in the process. This waste may be compensated by a more prolific production of eggs, which of course costs more energy. However, due to the principle of inexact copying, some early reptiles may have produced more spherical eggs, while those of other reptiles were less so. Thus, the nonspherical eggs, being more stable on the ground, were more likely to produce healthy offspring.

542

The nature of geometry and the geometry of nature

Inheritance A second principle of nature applies now: Offspring usually inherit most of their phenotypic properties from their parents. If, therefore, more parents have been born from “less symmetric eggs,” then – depending on the strength of this selective pressure – the next generation should exhibit a higher proportion of individuals laying non-symmetric eggs. If the selective pressure is strong, then it does not require many generations before the kinds of reptiles which lay “classically shaped eggs” – and not those who lay spherical eggs – become dominant.

The sum is what matters It may now be argued – quite wrongly – that this principle should apply to every trait of the organism, and that it should take only a few generations before a perfect solution is found for every problem (which in the case of the eggs would be purely geometrical). However, this runs contrary to a third principle of nature: The best sum of adaptations is usually the successful one, and this also depends on a constantly changing environment. If some reptiles, for instance, continue to lay spherical eggs but, for reasons of another trait that is affected by the same genes, are “better at evading predators”, then this might turn out to be a more successful adaptive strategy than “not laying spherical eggs”. It may be the case that the individuals who are better at evading predators also adapt to lay non-symmetric eggs without any negative effects on their evasive strategies. For lack of a better term, this would kill two birds with one stone. It may simultaneously occur that other, “better evaders” acquire a new trick by way of mutations that somehow lessen the disadvantage of spherical eggs. Whatever the situation might actually have been like, it seems that the advantage of more or less non-spherical eggs was so significant that this trait is now shared by virtually all oviparous land-based animals.

Phyllotaxis, or: How easily are we deceived? What appears to be a simple explanation for the non-spherical shape of eggs may require more profound scrutiny in other cases. A typical example is the arrangement of sunflower seeds, which is also known as phyllotaxis. Much has been written and theorized about this topic – and despite all of that, the solution turns out to be as ingenious and simple as evolution itself.

A premature conclusion Let us briefly discuss the underlying theories: Looking at a sunflower long enough, one will inevitably find spirals in the pattern. In fact, two opposing spirals can be discovered! It may further be noticed that the number of spirals in a pencil is always a so-called Fibonacci number. (More on this topic can be found in [9].) The golden mean is closely linked to these famous numbers, as is exponential growth. (By repeatedly multiplying a number with itself, we get a geometrical sequence which – if displayed in a coordinate system

13.2 Evolution and geometry

543

– yields an exponential curve.) We might thus be easily impressed: It seems that sunflowers are “aware” of the golden mean and grow exponentially – while most other plants do not!

A completely different explanation Now on to the most likely explanation (claiming to know the definitive solution for such matters may be misguided): A sunflower multiplies by means of its seeds, which are usually eaten by birds and dispersed because the birds that pick them up tend to lose seeds from time to time. One thing is clear: For this strategy to work, a sunflower has to produce as many seeds as possible. This increases the probability that the species may survive in the long run. Let us imagine a plant species (a predecessor of the modern sunflower) which may have adopted the following successful growth strategy during the course of its evolution: “Grow your seeds by creating a principal seed at the approximate center, and position each further seed such that the direction is changed and that the position is translated slightly away from the center.” In order for this procedure to be quantifiable, the rotation angle would have to be constant, as would the translation distance. Up to a certain point, this strategy would, indeed, allow the flower to produce new seeds. The plant would reach its natural limit when there is no more space for a new seed because it is occupied by an already existing seed.

Fig. 13.16 Different translation distances

Among the infinite number of combinations of angles and distances, there is certainly an optimal one. Evolution would eventually find it over the course of many generations, as it did with the shape of eggs: Mutation is constantly at work, changing angles and distances ever so slightly, and those flowers who are lucky to have hit upon a good combination would carry more seeds for their reproduction. “Their” advantageous combination would be passed on to their progeny, which have a chance of “improving” it further. The result is quite impressive: a very “close” approximation of a modern sunflower (Fig. 13.16 on the left). The center is a little bit tight – the seeds there would have to be smaller than those at the outer edges. The fact still

544

The nature of geometry and the geometry of nature

remains that this is a remarkably effective method of packing seeds into a blossom. We can also detect the aforementioned spirals. Indeed, this method creates them entirely without the need for exponential growth! The angle of rotation is quite peculiar, dividing the whole revolution of 360○ at the golden mean. The images in Fig. 13.16 at the center and on the right show further possibilities if the translation distance is allowed to decrease by a certain percentage as the seeds move away from the center. However, this is mere “cosmetics”. If this procedure were to be “extrapolated” onto a sphere, as illustrated in Fig. 13.17, then the seed density would increase even further.

Fig. 13.17 Computer simulations. On the right: Optimization by an extrapolation onto the sphere or ellipsoid.

⊕ Remark : From a daisy to a meter-high sunflower, a common explanation for some of their specific proportions can often be found in the “golden mean”. A fact that has fascinated many numerologists. This is not meant to be derogatory: Even such deliberations may be mathematically valid. It can be shown that the golden mean is the “most irrational of all numbers”: Φ=1+

1 1+

1 1

1+ 1+

1 1+...

≈ 1.6180339887.

The flower “needs” this irrationality, which makes it possible to apply the rotationtranslation-step to the seeds as often as possible. ⊕

The development is not always clearly visible By changing the golden angle ever so slightly, we get patterns as in Fig. 13.18 on the right. Such figures are already familiar to us: For instance, the blossom in Fig. 13.18 on the left already resembles the pattern very closely. Let us

13.2 Evolution and geometry

545

Fig. 13.18 Changing the “golden angle” by tenths of degrees

leave it at that, without coming up with any further hypotheses: In geometry, spirals are relatively easy to produce: Even when they are defined quite differently, the may be very similar locally. The spiral pattern in Fig. 13.18 on the left might owe its appearance to a completely different principle than the filling pattern of the blossom.

Fig. 13.19 Snapshot of a low-pressure turbulence in the making

Turbulences caused by low-pressure areas are another class of phenomena where we should not be too hasty in inferring the precise reasons for their appearance. Several parameters apply here. Conservation of angular momentum must surely play a central role, but so must lateral acceleration, which is connected to the north-south-expansion of the turbulence (different path velocities depending on the geographical latitude!), as well as widespread pressure drops and several other factors. Given this complexity of cause and effect, it is an undeniably great accomplishment of modern meteorology that accurate predictions of such large-scale weather patterns can be made up to several days in advance.

546

The nature of geometry and the geometry of nature

13.3 Planetary paths and fish swarms The forms of galaxies may very well be inevitable: On a large scale, outer space is essentially dominated by only a few laws, primarily by gravitational attraction and the law of inertia.

Fig. 13.20 Galactic spirals including their carrier surfaces of revolution

Let us hypothetically consider a galaxy like our own Milky Way, which forms as a result of the compaction of interstellar mass and, according to the law of conservation of angular momentum, is finally left with a constant angular velocity or momentum. Due to gravity, the center of this system will gradually increase in density (and may eventually form a black hole which will continue to “accrue” mass until it evaporates). The clusters of stars in the system will continue to move towards the center and increase their angular velocity in the process.

Fig. 13.21 A cosmic catastrophe (devastating impact) . . .

No matter what parameters one applies, one can always find a galaxy that is similar to a snapshot of the corresponding simulation shown in these pictures – and this simulation will always contain spirals made of star clusters. The Moon seems to have been formed 4 to 5 billion years ago by a collision of the newly-formed volcanic Earth with another massive celestial body. Following the impact, glowing chunks abounded in our planet’s neighborhood. Each of these chunks possessed the Earth’s angular momentum and drifted along in spiral motion before being “caught” on a circular orbit around the

13.3 Planetary paths and fish swarms

547

Fig. 13.22 . . . and the subsequent consolidation (Moon)

planet. A gradual accretion of mass followed – probably due to the lack of space and gravitational forces – and the Moon was thus gradually formed.

Fig. 13.23 The explosion cloud of a supernova passes our Sun . . .

It may “only” have been hundreds of millions of years prior to those tumultuous events that the remains of a supernova passed our still very young Sun, which managed to catch part of this debris by means of its gravitational pull.

Fig. 13.24 . . . and “produces” a planet.

The laws of physics then acted their part, and it did not take long for the supernova remains (which mostly consist of metals) to circle our star on elliptical paths (with the Sun being at one focal point). Collisions of the orbiting matter caused its gradual accretion until the planets were born. Our asteroid belt is probably nothing more than a not-yet-consolidated “souvenir” of that long gone supernova. One may now argue that these topics do not have much to do with geometry and that such speculation is best left to physicists. On the other hand, one may also consider it a beautiful example of separate academic disciplines supporting one another: Without computer simulations, which depend on computer geometry, the outcomes would certainly not look as spectacular

548

The nature of geometry and the geometry of nature

as they do in the resulting image, and the layman who is not able to solve differential equations would have to take physicists at their word.

Fig. 13.25 “Spiral lawn sprinkler”

The following question is closer to home: When a lawn sprinkler rotates using the repulsion of the exiting water streams, spirals are formed which resemble their galactic counterparts: As the water moves away from the axis of rotation, its angular velocity decreases by the square of the distance according to the law of conservation of momentum. Other factors apply here, such as air resistance and gravity, but this need not concern us here, as so much of this phenomenon is simply the result of chance. Let us examine another water-based scenario, but from a different perspective: The seemingly chaotic developments in outer space are not that far removed from, for instance, the simulation of a swarm of fish. This time, let us focus on the discoveries of biology. Small fish often exhibit a very sophisticated swarming behavior, not unlike that of many bird species.

Fig. 13.26 Impending danger and escape

Interestingly enough, there is no alpha leader determining the direction of the swarm. This whole choreography is rather the product of many singular reactions. The goal of a single fish is only to remain close to its neighbors (about a single body length). When foraging, individuals tend to be more leisurely while they move in the direction of more food. When a predatory fish takes interest in the swarm, the individuals in its vicinity will naturally want to flee from the place of danger. Their neighbors

13.3 Planetary paths and fish swarms

549

Fig. 13.27 Back to the swarm . . . and immediately away from it!

may not even have realized the cause of disturbance, but they still reflexively follow their neighbors on their paths of escape. This leads to a chain reaction (shock wave), which may even involve individuals that are far away from the predator. Once the danger has passed, the fish which are farthest away will once again seek the close company of their relatives. After a certain amount of time, and possibly until the next predatory attack, “order” will have returned to the swarm.

Fig. 13.28 An everyday occurance under water: Some cormorants are hunting small fish. They try to encircle the fish, but this proves to be quite a challenge amidst all the chaos . . .

This supposed chaos is actually governed by only a few parameters, which hardly restrict the variety of shapes that a swarm can have at any given moment (see also Fig. 13.28). ▸▸▸ Geometry as nature’s artistic inspiration It is not be mere coincidence that the shapes in this very interesting avantgarde architectural sketch by Andreas Krainer (“the Emperor and the Queen,” Fig. 13.29) resemble jellyfish, since the sketch consistently follows a geometrical plan of construction that is often found in nature: This entire sketch is based on a single space curve, which defines both the position of the beams and girders as well as the form of the hull. Beams and girders in the traditional sense no longer exist, and the transition between them is completely smooth. By a multiplication and a deliberate positioning of the generating curves into a specific pattern (such as a hexagon whose

550

The nature of geometry and the geometry of nature

Fig. 13.29 Art and nature

center and corners contain one copy each), a radial system defining the tower is created. The relation between one tower and the next is the same as that between one supporting beam element and the next. This produces a repetition of the same principle of arrangement, only on a higher scale. A change of the generating space curve changes the whole sketch, which allows for an unimaginable variety of possibilities. ◂◂◂ ▸▸▸ Organic architecture

Fig. 13.30 Dome, rib vault, barrel vault

A geometrically interesting sketch was created by Matthäus Wasshuber. Proceeding from classical vault shapes (Fig. 13.30), which were themselves inspired by nature: He connected his vault-like modules following examples found in the plant kingdom (Fig. 13.31).

Fig. 13.31 Inspired by the shapes of plants

13.3 Planetary paths and fish swarms

551

After a longer process of experimentation, he produced the sketches shown in Fig. 13.32, which combine shapeliness with the capacity to carry large weights.

Fig. 13.32 New architectural formations

◂◂◂

552

The nature of geometry and the geometry of nature

13.4 Scaling behavior in nature To some degree, it is possible to deduce how big an animal is by “looking” at a neutral photograph (without the background or other objects in the vicinity being visible): An elephant’s legs are so massive because they need to be able to carry the animal’s own weight. The tiger, being the largest land predator, also needs to have characteristically large muscle diameters. (The tiger’s paw is famous for its sturdiness.)

Fig. 13.33 The largest herbivore and the largest carnivore on land: Proportionally speaking, both animals need higher muscle diameters.

Reducing the size by two orders of magnitude (Fig. 13.34) takes us to the world of insects and other articulate animals. Their muscle diameters need not be so large anymore: The weight of the animal has, in fact, diminished cubically in relation to the scaling factor, while the muscular force has only been reduced in square proportion to the diameter. Interestingly enough, both tigers and wasps bear striped patterns – as do many other animals. In the case of the wasp, this may be explained as a warning signal, but on the tiger it is a form of camouflage. Comparable geometrical patterns are employed in different ways here.

Fig. 13.34 Large herbivores and carnivores on the macro scale: Proportionally speaking, both animals need far smaller muscle diameters.

13.4 Scaling behavior in nature

553

It may be arguable to what degree a giraffe actually resembles the seahorse in Fig. 13.35, but consider the following: Geometrically speaking, there is a limited amount of possibilities of “fitting” volumes and functionality into a confined space. Given the immense variety of lifeforms, one should, therefore, expect to stumble upon certain similarities eventually. Apart from the curious shape of their heads, however, the giraffe and the seahorse have very little in common. They each live in completely different conditions, to say nothing of their different scales.

Fig. 13.35 There is certainly a geometrical resemblance, including the mane or the dorsal fin, but that is about it.

Geometrical similarities often give the misleading impression that the underlying laws that produced these shapes must have been comparable. This may not have been so. We do not even have to mention the strange laws that govern physics at the quantum scale to conclude that, from a mathematical and physical perspective, small-scale events do not have to proceed the same way on a large scale.

Fig. 13.36 Scaling behavior: It is difficult to determine the size of such a stone formation. This is why in the left image the stone formation looks like a big lizard being fed.

This scaling behavior is less obvious among inorganic objects: As in Fig. 13.36, it does not seem to matter for a weathered rock whether it measures several meters or just a few centimeters.

554

The nature of geometry and the geometry of nature

Fig. 13.37 Ice crystals – only slightly enlarged

Fractal forms – the “frayed silhouette” which seems to repeat itself over and over again – occur both on large and on small scales. It has been proven that it is virtually impossible to ascertain the approximate size of a cloud from a mere photograph.

Fig. 13.38 Glaciers and screws of ice crystals

When comparing Fig. 13.37 to Fig. 13.38, we may notice that frozen water tends to produce fractal contours of some aesthetic value at every scale. It is no wonder that such forms have always inspired artists to produce novel creations (Fig. 13.39).

Fig. 13.39 Art and nature: Zaha Hadid, Ice Storm

While modern architecture is certainly concerned with the creation of attractive forms whose variety is often taken from nature, the ideal case combines

13.4 Scaling behavior in nature

555

mere aesthetics with the implementation of certain useful insights. Fig. 13.40 shows the implementation of the “shark skin principle” (application p. 516) in the creation of an architectural structure – in this case, the forms of separate scales of shark skin have been taken as templates. Their advantages in aerodynamics have been proven by realistic simulations.

Fig. 13.40 Another creation from Studio Hadid: the scales of shark skin as the underlying principle which manifests itself both in detail (application p. 515) and in the building as a whole and which is supposed to yield aerodynamic advantages both on great and small scales.

In the architectural sketch by Martin Zangerl for the Centre for Digital and Media Technology in Los Angeles, a prototype of a spatial knot (a minimal surface) is used to transform a voluminous structure into a “bony,” open structure (Fig. 13.41, bottom left) by means of variation. This procedure occurs both on a small scale and on a large scale (top left, right), so that parts of buildings with either completely closed or highly open hulls may emerge.

Fig. 13.41 From voluminous museum halls to open offices

556

The nature of geometry and the geometry of nature

13.5 Musical harmony through the eyes of geometry Many mathematical and geometrical relations can be found in music. We shall focus on three particular examples here. Along with parts of the text itself, these examples are taken from [1]. An entire appendix of [9] is dedicated to the topic of music. The images were created with the programming library Open Geometry. Readers who do not possess any prior knowledge of music theory are simply invited to enjoy the mathematical balance inherent in music and the geometric visualizations that it enables.1 ▸▸▸ Displaying a tonal system on a torus A torus is cut into 12 slices (Fig. 13.42). On each slice there are 12 spaces (to keep it simple, these are identified only once in the image), which may either be interpreted as chromatic-enharmonic locations of the tonal system (12 major and minor keys) or as enharmonically changed tones.

Fig. 13.42 Displaying a tonal system on a torus

In 12 convolutions, the torus is entwined by a rotoid, which intersects the slides in every point, producing 12 enharmonically closing circles of fifths. ◂◂◂ ▸▸▸ The “grid of keys” By means of a grid of congruent circles, Fig. 13.43 visualizes a circle of fifths 1 There

is a significant difference between English and German notation (http://en.wikipedia. org/wiki/Key_signature_names_and_translations): C, D, E, F , G, A have the same signature in both languages. The letter H, however, is denoted by B in English; Instead of Cis, Dis, F is, Gis, Ais (German), one writes C ♯, D ♯, F ♯, G ♯, A ♯; instead of Ces, Des, Es, Ges, As, B (German), one writes C ♭, D ♭, E ♭, G ♭, A ♭, and B ♭.

557

13.5 Musical harmony through the eyes of geometry

with all notes and chords for the respective key, including the circle of the parallel key as well as the subdominant, tonic, and dominant scale degrees.

Fig. 13.43 Grid of keys in the plane

Enharmonic closure has been attempted in Fig. 13.44. Geometrically speaking, this involves the development of Fig. 13.43 on a cylinder of revolution. A transformation onto a torus or a sphere is also possible. ◂◂◂

Fig. 13.44 Closed grid of keys

Fig. 13.45 Tonal system

▸▸▸ Three-dimensional circle of fifths Fig. 13.45 shows an attempt at connecting the closed circle of fifths in equal temperament (red surface) with the “spiral of fifths,” which is open upwards and downwards (it is actually a helix, to be geometrically precise). The base tones lie on the central plane (red), as well as in the ascending spirals of the and areas (light beige, cream) above and in the descending spirals of the and areas (dark red).

558

The nature of geometry and the geometry of nature

The enharmonically changing tones lie on the vertical green lines. The connecting straight lines of corresponding tones form two skew closed helical ruled surfaces (see Fig. 7.30). ◂◂◂ ▸▸▸ Tonal centers

Fig. 13.46 A tonal system with columns. On the right: new tonal center

Fig. 13.46 shows the C-major tonality as an example of a tonal system. The columns in the inner circle display the triads which correspond to this scale. In the outer circle, the typical sounds of the extended C-major tonality can be found on top of the chromatic tones (D-flat-major as the Neapolitan chord, B-flat-major as the double subdominant, F-minor as the minor form of the subdominant, D-major as the double dominant, C-minor as a variation of the tonic, and B-major as the dominant of the dominant parallel E-minor). Every sound or tone represented by a column or a sphere may become the new tonal center (Fig. 13.46 on the right), which happens by a procedure of ◂◂◂ modulation. ▸▸▸ Inverted retrograde canons

Fig. 13.47 A canon by J.S. Bach which may be played forwards and backwards but also by inverting the notes on the central line. After one circulation, the notes have been inverted. The second melody nevertheless harmonizes with the first and should, in fact, be played simultaneously.

Fig. 13.47 shows a Möbius strip designed by Franz Gruber with the use of our own in-house software, with which a “marquee” displaying a canon by J.S. Bach has been visualized by means of a texture. An animation of this intriguing object can be found on the website to the book. ◂◂◂

14

More applications

In this chapter, we consider additional applications that may be interesting for the reader. Sometimes these applications are independent of the previous chapters, more often they use insights gained from previously discussed topics. First, we will deal with multiple reflections or refractions, with illusions, and with so-called “impossibles”. Then we go into further detail with inversions. Finally, we will return to the topic of mathematical patterns like Voronoi diagrams and fractals, which seem to be omnipresent in nature. The above picture is a close-up of a diatomeen that measures only some 1/20 mm in diameter. These tiny microalgae, which are found in the oceans, waterways and soils of the world generate a large amount of the oxygen produced on the planet. One can detect amazing patterns under a scanning electron microscope.

© Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3_14

559

560

More applications

14.1 Multiple reflections, illusions, and impossibles ▸▸▸ Multiple reflections in two orthogonal mirrors With multiple reflections in two perpendicular planes, we can create a remarkable effect, whereby left and right – and not, as in the ordinary mirror, the front and the back – are reversed. What exactly is happening here? For the sake of simplicity (Fig. 14.1), two planes ξ and η are assumed to be vertical coordinate planes with the equations x = 0 and y = 0. Each of the planes initially generates a virtual – usually reversed – counterpart Ωx (change of signs in the x-values) or Ωy (change of sign in the y-values). The two objects are indirectly congruent and – regarding the issue of perception – are of equal rank as the original Ω.

Ωyx

Ωxy

Ωx Ωy Ω

Fig. 14.1 Several images in two mutually per- Fig. 14.2 Several images in three mutually perpendicular mirror planes pendicular mirror planes

Consequently, Ωx has a virtual counterpart Ωxy through reflection in η, and Ωy has a virtual counterpart Ωyx through reflection in ξ. However, because of the special position of the mirror planes (ξ ⊥ η), the two new objects are identical: Ω∗ = Ωxy = Ωyx . Furthermore, we can only get a partial view of them in the respective “mirror window”. The part labeled with Ωyx is produced through reflection in the right mirror window of the visible virtual object Ωy in the left mirror window. The two mirror windows touch each other along the edge s = ξ ∪ η (according to our choice, the z-axis); so, they merge into a single window which consists of two mutually perpendicular rectangles. This allows us to see our object Ω∗ . It was created by double-reflection and is, therefore, directly congruent to Ω. The two directly congruent objects Ω and Ω∗ can be transformed into each other by a half-turn about the intersection s of the mirror planes or by an axial reflection in s. Thereby left and right are interchanged at first, and the characters are still readable as usual.

14.1 Multiple reflections, illusions, and impossibles

561

In the photo in Fig. 14.1, the “auxiliary objects” Ωx and Ωy are entirely visible. In human vision, one normally only sees Ω∗ in the image – comparable to an ordinary mirror image, but left and right are reversed. ◂◂◂ ▸▸▸ Reflection of a water wave Even though water waves do not have the exact same properties as light waves, we can tackle the problem of multiple reflections in a similar way:

Fig. 14.3 A water wave in a container propagates and hits a wall. From then on it is geometrically useful to take the virtual reflected wave into account.

Imagine a wave propagating in a pool. As long as it does not hit a wall, the simulation is easy (Fig. 14.3 to the left). Once the wave hits a wall, there will be interferences. They can easily be controlled when we consider a “virtual counter wave” emanating from the wall (Fig. 14.3 to the right).

Fig. 14.4 Two walls: Now we have to consider three “virtual counter waves”.

If there is a second wall perpendicular to the first one, considerations become more tricky. Clearly, the second wall will create an additional virtual counter wave which interferes with the wave pattern in the pool. Additionally, those parts of the wave that reach the rectangular corner will be doubly reflected (like a ball on a billiard table). The effect of this can be determined by considering a third virtual wave that is a secondary reflection of the reflected waves on both walls. ◂◂◂

562

More applications

▸▸▸ What exactly happens between two parallel mirrors? Consider the confusion that is created by two parallel mirrors in Fig. 14.5: By changing the distance settings, the photographer was able to focus on any of the available originals or reflections. Visually, the observer is unable to distinguish between original and virtual objects, so that it is not even guaranteed that the person depicted is actually seen as a real person and not just their mirror image – this depends on the focal length that is actually used. That is to say, it depends essentially on the aperture of the viewing cone.

Fig. 14.5 Three similar scenes, but in each of them, a different reflection is in focus. Can you see where “the original” is?

Let A be the position of the observer (Fig. 14.6) standing between two mirrors σ1 and σ2 (distance d apart). The camera, which is directed towards the axis a, can only capture those things that are within the cone of vision ∆. P3

2v ∆

a P1

σ1

u u

A

P0

v

d σ2

v P2 Fig. 14.6 For each virtual point, a new one arises at the “speed of light”.

Now, assume that there is another person (symbolized by a point P0 ) standing between the mirrors, at a distance u from σ1 and at a distance v from σ2 :

14.1 Multiple reflections, illusions, and impossibles

563

u + v = d. Thus, two virtual mirror images P1 and P2 arise at the distances u and v behind σ1 and behind σ2 . The two points are a distance 2u + 2v = 2d apart. P2 is visually indistinguishable from a real point and is reflected in σ1 to a point P3 . This lies at distance 2d from P0 . If one continues in that way, one obtains two congruent series of points P0 , P3 , . . . and P1 , P5 , . . . whose points are separated by a constant distance of 2d. In Fig. 14.5, these series are clearly visible. (In one of them, the person can be seen from the front, in another from behind.) In both Fig. 14.5 and Fig. 14.6, the observer and the multiple reflections are not contained in the cone of vision. It is noteworthy that the autofocus of the camera has no problem focusing on any reflection, which again demonstrates that a purely optical mirror image is indistinguishable from reality. The distance to which the autofocus adjusts equals exactly that of the “reflected” person in the room – and not the distance to the mirror. The repeated reflection causes a loss of brightness, so that reflections that are further away appear less clearly ◂◂◂ (darker). ▸▸▸ Analyzing a selfie (Fig. 14.7) Let us now look in detail at what can be seen in the photo inside an almost fully-mirrored elevator cabin.

Fig. 14.7 Can we now explain every single virtual image?

First of all, the photo does not show the real person but only virtual images of the person. Due to the design of the camera, the person pushes the trigger button of the camera with the right index finger. So, all the virtual images where the person appears to use the left index finger are reflections of order

564

More applications

1, 3, 5, . . . (red circles), and the other ones of are of order 2, 4, 6, . . . (blue circles). The mirror images that are circled in blue are actually composed of two partial reflections of even order: The edge of the cabin wall is the border line in between. However, note the following: This edge is acutally always a mirror image of the real edge behind the person. What about the image circled in yellow? According to what was previously said, it is a composition of three reflections, and in total it is a point reflection at the corner of the cabin. Even though the finger pushing the trigger cannot be seen, it will be on the right-hand side.

Fig. 14.8 Distorted mirror images in an amusement park

As “homework” you can try to analyze the residual reflections, e. g., those in the upper mirror. After that you could examine the selfies in Fig. 14.8, which were taken in an amusement park (Fig. 14.8). ◂◂◂ ▸▸▸ Vision underneath the surface (Fig. 14.9) In Chapter 9 (p. 403ff), we discussed Snell’s window and the total reflection at the water surface outside this window. Let us analyze the situation in Fig. 14.9, which is a drawing by my daughter Sophie: First of all, Fish A (a grouper) can clearly see all the other fishes around it. Additionally, due to the law of reflection, it will see – though in a distorted form – everything that is outside the water, which appears compressed into the circular Snell’s window. This circle is the base of a cone of revolution Γ with apex A. As a reflection on the surface, we get another cone of revolution Γ∗ with apex A∗ . Everything that is outside of Γ∗ will – for fish A – also be visible as a total reflection. Thus, the puffer fish C appears twice to our grouper. The third fish B swims mainly inside Γ∗ . However, its dorsal fin is partly outside. So, A will see B’s dorsal fin as a total reflection immediately outside the limiting circle c.

565

14.1 Multiple reflections, illusions, and impossibles

B∗ C∗

A∗ β0

Snell’s window

R

β0 C A

B

Fig. 14.9 Who sees whom? Fish A looks at its environment. What does it see? This question is by no means trivial!

Fig. 14.10 Photographic proof in the bath tub and another experiment with a fish whose dorsal fin is notoriously famous.

In Fig. 14.10, the situation with the dorsal fin is slightly different, since the fin is partly above the surface. The tip of the fin outside the water is, thus, visible in Snell’s window. The photo to the left was taken with an underwater camera. However, the fish was a plastic model and the situation was recreated in a bath tub. In a calm sea, sharks can also see clearly what is happening outside the water as they swim with their dorsal fin above the surface. When there are more waves, sharks have been observed poking their heads out of the water in order to get a better view (“spy hopping”). As a final task, we might ask ourselves what a backswimmer (Fig. 14.11) can see in its usual position “hanging” from the water surface. It must have an overview of the whole environment – both underneath and above the surface. ◂◂◂

566

More applications

Fig. 14.11 Backswimmers (Notonectidae) are powerful aquatic insects that hang upside down from the water surface.

▸▸▸ Winding to the left or winding to the right?

Fig. 14.12 This is a snail and its reflection. Viewed from above, the shell winds clockwise. In the mirror, however, it winds counter-clockwise.

Snail shells or mussel shells that “expand in three dimensions” can be either left- or right-handed. Almost all snail shells wind in the clockwise direction (mathematically negative) when viewed from above. This is not the case for the “snail king”. Its shell “winds to the right”.

14.1 Multiple reflections, illusions, and impossibles

567

Fig. 14.13 Spirula spirula (also named little post horn squid, a species of deep-water squid) has a shell inside its body. Drawing by Ewald Rübsamen.

For the shell of the little post horn squid in Fig. 14.13 – at least at first glance – there is no view from above or below, because the spiral of the shell is visible from both sides. Therefore, you cannot say in which direction the spiral is wound.

Fig. 14.14 Christmas tree worms have two “crowns” in mirror-symmetric forms.

Fig. 14.14 shows strange organisms that are part of the species Spirobranchus giganteus, which lives on corals. Here we see spiral surfaces that wind both in clockwise and counter-clockwise direction. ◂◂◂

568

More applications

Illusions and impossibles ▸▸▸ Hexagons and cubes

Fig. 14.15 Typical illusions with planar hexagons.

Fig. 14.15 shows a common illusion created with tilings of planar hexagons: Each hexagon is split into three rhombs that are painted in different colors. For the human brain, this creates the impression that we are looking at cubes or similar polyhedra.

Fig. 14.16 Planar pattern or a cube-packing?

In Fig. 14.16 a pattern was created by computer. The question whether the displayed object is two-dimensional or three-dimensional cannot be answered.

Fig. 14.17 Left: A photo of a reflecting polyhedron; middle: the explanation; right: look twice, or maybe even three times!

Fig. 14.17 shows a series of macro photos of reflecting polyhedra (cubes), which are arranged similarly to the ones in Fig. 14.16. Look closely at the

14.1 Multiple reflections, illusions, and impossibles

569

pictures from left to right. It is almost impossible to concentrate. Hint: The labeling in the rightmost photo is correct, even if you may think it is not. The depicted object is a reflector on the spokes of a bicycle (application p. 62). ◂◂◂ ▸▸▸ Zoetropes

Fig. 14.18 A disk with a number of equally distributed objects that display in-between motions of the object. When rotated at a certain angular speed, the brain is “fooled” and sees only one object in motion.

Fig. 14.19 Here a pile of intersecting cubes is rotated. The pile, however, is created with a system: Corresponding cubes are twisted slightly with each rotation. With the right angular speed of the disk, the cubes in the pile appear to revolve.

A zoetrope is a pre-film animation device that creates the illusion of motion. A sequence of still images depicting objects at different stages in motion is shown at such a high frequency that the human brain is led to believe that the object is moving. ◂◂◂ ▸▸▸ The Freemish crate, also called Escher’s cube An “impossible” is an object which implies an apparent contradiction with regard to the visibility of its constituent parts. A classic example can be seen in the left image of Fig. 14.20. The second image in Fig. 14.20 shows how such an object could actually be constructed, exhibiting the illusion of impossibility only from a certain well-defined perspective – in this case, only in a normal projection. If we had a perspective image (as a result of a central projection), we would need another opening in the object; otherwise, the trick would be revealed (Fig. 14.20, image to the right). ◂◂◂

570

More applications

Fig. 14.20 Left: a classic impossible. Middle: The underlying trick is revealed. Right: problems with a central projection.

▸▸▸ The Penrose triangle, also known as the Penrose tribar Fig. 14.21 shows how to create another impossible. Let us first look at a

Fig. 14.21 An impossible triangle (from left to right): (1) the underlying idea, (2) its secret is revealed, (3) removing one and a half cubes from one rod, (4) the trick is revealed again.

cube from a perspective that allows its diagonal to appear as a point. During normal projections, this produces a very regular shape. (The projections of the edges form an equilateral hexagon.) Let us now group additional cubes around three of the original cube’s edges (as in the picture to the left), so that they form three square rods, which together produce a sort of skewed triangle. If we now omit the upper cube and one half of the next cube, the entire structure will appear to be closed in normal projection (Fig. 14.21, third from the left). This is confusing, as it thwarts our expectations of the visibility of the object. The trick is revealed again when we change the direction of the projection ray (Fig. 14.21, image on the right). ◂◂◂ ▸▸▸ Does this work in perspective images, i.e., in photographs? The question is whether an object like the tribar in Fig. 14.22 could be photographed in such a way that the “error” would be impossible to detect. We have to be aware of the fact that a geometrically perfect normal projection cannot, to date, be simulated by a single photo. By employing an extremely telescopic lens (with a focal length exceeding 1,000 mm), we can approach

14.1 Multiple reflections, illusions, and impossibles

571

Fig. 14.22 This matter is even more difficult with a perspective image (sizes change!).

a normal projection relatively well. Still, we must change the sizes of the objects in order to avoid errors when taking pictures from a specific eye point. In the following applications, there will be an explanation as to how this can be achieved. ◂◂◂ ▸▸▸ Perspective illusions Fig. 14.23 shows a typical illusion. It only works perfectly from a certain position of the eye (in this case on the principal normal of the frame). In this case, a normal projection would be counter-productive (image in the middle). The spatial scene consists of a set of spheres. The further away the spheres are, the bigger they have to be for the illusion to work. The image on the right shows how the spheres are arranged. ◂◂◂

Fig. 14.23 Typical illusion (left to right): eye point in special position, normal projection, spatial situation. Note that the closer spheres have to be smaller when they are further away.

▸▸▸ Rolling upwards? On the Internet, one can find fascinating examples of optical illusions, like the one created by Kokichi Sugihara in which balls appear to roll uphill (https: //www.youtube.com/watch?v=hAXm0dIuyug). Fig. 14.24 shows a similar idea, which was programmed by Franz Gruber. How does it work? Everything depends on the fact that your eye point has to be forced in

572

More applications

Fig. 14.24 The sphere rolling uphill.

Fig. 14.25 Explanation for the “Kokichi Sugihara” illusion

a certain position. If, from this position, you think that you are looking at a “stable and balanced construction”, your brain will immediately interpret the heights of certain points in the construction and it will tell you: The platform in the middle has the highest position.

Fig. 14.26 Another comparable illusion and its explanation

However, the construction is not symmetric and stable. Its vertices lie somewhere on the projection rays through the vertices of the alleged construction. Among the infinitely many possibilities, you should now choose a nonsymmetric construction where the platform is in a lower position. With more complicated objects, one should employ spatial perspective collineation to calculate the corresponding object. ◂◂◂

14.1 Multiple reflections, illusions, and impossibles

573

▸▸▸ Inside or outside? In the course of the renovation of the Foundation of Francisco Giner de los Ríos in Madrid, Cristina Díaz Moreno and Efrén García Grinda created a remarkable environment: This garden is a space that is determined by and changes through the way someone is looking at it and participating in this space. The proposed spatial system consists of a series of rooms, some roofed and others open to the elements, which redefine the existing garden and combines the old buildings and the new ones.

Fig. 14.27 Varying views from different positions

Fig. 14.28 The overall concept (on the right) and detailed planning

This garden is not green but purple, coral and silver, resembling the Castilian plateau like Giner saw it. It is defined not only by the changing colors of the plants but by the changing filigree of the cladding and the overlapping succession of leafy envelopments – the vegetation, the outer wall, the reflections in the glass, the bearing structure, people in movement, the stairs and the permanent exhibition system. The size and position of the rooms is determined by our moving eyes, based on a precise study of the lines of sight of the new route inside the garden. If we regard our eyes as projectors, rather than screens for capturing information, then we can use them to shape the diagonals, the overlaps of the different planes of the garden. ◂◂◂

574

More applications

14.2 More about inversions in space Inversion in a sphere In Section 1.5, we have already discussed the inversion in a circle. When r is the radius of the inversion circle, then a point P with distance d to the inversion center C will be transformed into a point P ∗ on P C with distance r2 /d. We can also say: P P ∗ = r2 . We had the following main properties: The transformations works in both directions. Even though it is not linear, it preserves circles and angles. Straight lines have to be considered as generalized circles, so that in general, straight lines are transformed into circles through the center C. Conversely, circles through the center C are transformed into straight lines. When we generalize this transformation into 3-space, we replace the inversion circle by an inversion sphere. Again, the formula P P ∗ = r2 defines the transformation, and it is revealed that additionally to the already mentioned main properties, the transformation turns spheres into spheres and preserves angles in space. Planes can be considered as generalized spheres with infinitely large radius. So, planes are also transformed into spheres that contain the center C. Conversely, spheres that contain C are transformed into planes.

torus

cyclide

inversion sphere

Fig. 14.29 Inversion in a sphere: A ring torus is transformed into a ring cyclide.

14.2 More about inversions in space

575

▸▸▸ Inversion of a torus In Section 6.5, we considered Dupin cyclides, which are algebraic surfaces of degree four with special properties. By analogy with the ring torus, we introduced the “ring cyclide” as an inversion of a ring torus in a sphere (Fig. 14.29). A ring torus is – like any surface of revolution – enveloped by spheres of varying sizes centered on its axis. Two of those spheres that touch the torus along a parallel circle and contain the center of the torus are thus transformed into “infinitely large” spheres through the center C, i.e., into planes. As a nontrivial result, a ring cyclide has two exceptional tangent planes. If we invert a spindle torus or a thorn torus, we get the other types of cyclides (the needle cyclide and the double-horn). ◂◂◂ ▸▸▸ Inversion of cylinder and cone of revolution

Fig. 14.30 Inversion in a sphere: A cylinder of revolution is, in general, transformed into a needle cyclide.

Astonishingly, the needle cyclide and the double-horn can also be generated by inverting a cylinder of revolution or a cone of revolution, respectively. Fig. 14.30 shows that the needle cyclide occurs when we apply the inversion to a cylinder of revolution. The pinch point is the inversion of the infinitely far “apex” of the cylinder and is thus in the center of the sphere. The rulings of the cylinder are transformed into circles that lie in the connection plane of the line with the inversion center. Here it is again quite clear that the cyclide has two exceptional tangent planes (which are best seen in the upper-left image of Fig. 14.30). Inversion also works well with cones of revolution. In the general case, this will produce a double-horn (Fig. 14.31). One cusp is the center C of the sphere; the other one corresponds to the apex of the cone. ◂◂◂

576

More applications

Fig. 14.31 Inversion in a sphere: A cone of revolution is, in general, transformed into a double-horn cyclide.

▸▸▸ An almost extraterrestial figure By means of inversion, one can create a nice and non-trivial figure (Fig. 14.32): We start with a given number of congruent spheres and arrange them in a circular way. (Their centers are then vertices of a regular polygon.) Now they fit into a torus. When we apply an inversion, the two circles of the torus in the symmetry plane are transformed into two new circles. (One has a certain degree of freedom by choosing the center C of the inversion sphere.) The spheres are also transformed into non-congruent spheres which touch each other and form a chain. However, the centers of these spheres lie on an ellipse (compare Section 5.2). Without inversion, creating such a figure would be a very difficult task to accomplish.

Fig. 14.32 A non-trivially closed chain of spheres or circles

577

14.2 More about inversions in space

Fig. 14.33 Plausible generation of crop circles, courtesy of Franz Gruber

⊕ Remark : The figure was created after someone had shown the author photographs of crop circles like the one depicted in Fig. 14.33, upper left. Even though it has been repeatedly demonstrated how humans can produce this kind of hoax (https: //en.wikipedia.org/wiki/Crop_circle), many still believe that the patterns are messages from “aliens”. Fig. 14.33 shows sample screenshots from a simulation by Franz Gruber which shows how this pattern can be produced efficiently. A give-away clue are the – always present – tracks left by agricultural machines, because people who produce the patterns have to move across the wheat field along such tracks. ⊕

◂◂◂

▸▸▸ The loxodromes on a sphere

C

Σ∗

s∗

s Σ Fig. 14.34 Inversion of a logarithmic spiral s → (inversion center C), which is simultaneously a stereographic projection from C: The carrier plane Σ of s is transformed into the sphere Σ∗ through C. s∗

Another example illustrating the usefulness of the inversion in a sphere is the following: The famous logarithmic spiral intersects all rays emanating from

578

More applications

its center at a constant angle (Fig. 14.34). We choose the center C of the inversion sphere on the normal through the center of the spiral s. Then the carrier plane Σ of s is transformed into a sphere Σ∗ centered on the normal that goes through C. The points of the inverted spiral s∗ lie on rays through C and on Σ∗ . The rays are transformed into meridian circles of Σ∗ , and due to the angle-preserving property of the inversion, s∗ intersects all those meridian circles under a constant angle. We have already discussed such loxodromes at the end of Section 6.3. By means of inversion, we arrived at the result in a very efficient manner. The task also relates to the topic “stereographic projection” (Section 5.4): The center C of the inversion sphere is the North Pole of Σ∗ , so-to-speak, and this North Pole is now the projection center for the stereographic projection. ⊕ Remark : The inversion of a logarithmic spiral in a circle around the center of the spiral is again a logarithmic spiral: It is angle-preserving, and logarithmic spirals are loxodromes of all radial rays. ⊕ ◂◂◂

▸▸▸ Inversion of a clothoid c

c∗ e e∗

Fig. 14.35 A clothoid c (black) with evolute e (blue) is inverted in a circle around the inflection point, which generate pseudo spirals c∗ (red) and e∗ (green). A series of osculating circles of c∗ is drawn to show how evenly the circles are distributed.

A clothoid has the remarkable property that the curvature radius changes in proportion to the arc length (see also Fig. 4.5). The inversion of a clothoid c leads to a curve c∗ which is “optically similar” and may be called a “pseudo

14.2 More about inversions in space

579

spiral”. Moreover, the evolute e, which is the locus of the centers of all osculating circles, is another kind of pseudo spiral. When we invert e, we get another pseudo spiral e∗ that looks almost like a clothoid (Fig. 14.35). ◂◂◂ ▸▸▸ Sterographic projection of a clothoid

Fig. 14.36 A clothoid is stereographically projected onto a sphere.

One more example relating to the topic of stereograhic projection: As a consequence of the definition of a clothoid, all osculating circles are arranged such that they never overlap at least for one half of the curve. If we project the curve onto a sphere (e.g., above the inflection point), this remarkable pattern of circles is transformed into a non-trivial pattern of circles on the sphere without any overlapping (Fig. 14.36). ◂◂◂ ▸▸▸ Inversion in a cylinder (axial involution) Let us once more go back to the inversion in a circle. With the radius r of the inversion circle, a point P with distance d to the inversion center C will be transformed into a point P ∗ on P C with distance r2 /d (P P ∗ = r2 ). Now we generalize this transformation into 3-space in another fairly natural way: We replace the inversion circle by an upright cylinder of revolution (Fig. 14.37 to the left). A space point P is inverted in the cylinder as follows: We consider the top view P ′ of P , invert it in the base circle of the cylinder, and go back in the same height as P . Let us determine the properties of this kind of inversion. Clearly, straight lines and planes perpendicular to the axis are fixed as a whole. A coaxial

580

More applications

Fig. 14.37 Left: The axial inversion of a straight line is a cubic circle. Right: A helispiral with an Archimedian spiral as top view is transformed into a spiral with a hyperbolic spiral as top view. Its carrier surface of revolution is of degree four.

cone Ψ (apex C) with meridian with z = kx is mapped to a surface of revor2 lution Ψ∗ with the regular hyperbola z = kx (Fig. 14.37 on the right). However, what is, for instance, the image s∗ of a straight line s? The top view s′ is transformed into a circle through C, and s∗ lies on a cylinder of revolution that contains the axis of the inversion cylinder. The curve itself can be identified as an upright cubic curve. Generic planes are “even worse”. Whereas, in the case of an inversion in the sphere, the image is a sphere through C, the plane transforms into a surface that is far more complicated, namely a surface of degree three. We see: The axial involution is not nearly as useful as the involution in a sphere. Still, one can produce nice images like the one in Fig. 14.37 on the right, where a helispiral is transformed into a spiral winding up the afore mentioned surface of revolution Ψ∗ . The top view is inverse to an Archimedean spiral, and therefore, a hyperbolic spiral. ◂◂◂

581

14.3 Voronoi structures

14.3 Voronoi structures

Fig. 14.38 A leaf under the magnifying glass

Fig. 14.39 The wings of a dragonfly

Fig. 14.40 Cracks in dried mud

Let us assume a plane on which a set of points has been scattered. Our task is to subdivide the plane into convex regions (whose centers are de-

582

More applications

fined by the given points) such that the closest point of any location within a convex region is always the centre of the same region. This can be accomplished by calculating the perpendicular bisectors of all possible pairs of points (Fig. 14.41 left). For each point, the perpendicular bisectors to all adjacent points produce a convex region. If all convex regions are combined, a so-called Voronoi diagram is produced (Fig. 14.41 middle).

Fig. 14.41 Tesselation of the plane with convex polygons, starting from an arbitrarily chosen point cloud. Right: the surface of the fruit of a philodendron.

▸▸▸ Iterative Voronoi structures

Fig. 14.42 Optimization of the tesselation: The random point set is iteratively improved by replacing the original centers with the barycenter of the adjacent convex polygon.

In Fig. 14.42 on the left, randomly distributed centers were first chosen, from these centers a Voronoi diagram was derived. It is noteworthy in this case that the sizes of the individual cells vary substantially. If one wanted to equalize the cell sizes iteratively, one could employ the following strategy: As the (red) centers do not precisely overlap the centroids (green) of their respective region, one could, in a next step, replace the red centers with green centroids (Lloyd’s algorithm) and re-calculate the Voronoi diagram. It would

583

14.3 Voronoi structures

have the same number of cells at roughly the same locations. However, the cell sizes would be significantly more balanced (Fig. 14.42 on the right). We can speak of “iterative Voronoi structures”.

Fig. 14.43 This photo shows the bottom side of a fungus whose structure strangely resembles an (iterated) Voronoi diagram.

Fig. 14.43 shows the bottom side of a fungus – associations with a Voronoi diagram are unavoidable. ◂◂◂ ▸▸▸ Some classic examples in nature

Fig. 14.44 Intriguing basalt formations

The pictures in Fig. 14.44 show intriguing basalt formations at the famous echo cliffs in Iceland. Basalt in its extrusive form is a volcanic rock formed by the cooling of extrusive basaltic lava at or very near the surface. The contractional fractures form during the cooling of thick lava flow. The topology of these columns’ lateral shapes forms a random cellular network closely resembling a Voronoi diagram. Hexagons appear to be dominant in the crosssection. However, one also frequently encounters pentagons, heptagons, and other polygons. The slower the cooling process, the larger these polygons are. ◂◂◂

584

More applications

▸▸▸ Voronoi diagrams on the sphere

Fig. 14.45 Voronoi diagrams on a sphere, starting with random points (left). Even with extremely unevenly distributed cells, each iteration “improves” the mesh, and eventually, the results almost always look astonishingly similar.

The recipe for the creation of Voronoi diagrams also works on curved surfaces, e.g., on a sphere. In the spherical case, the perpendicular bisectors of all possible pairs of points are great circles on the sphere, and the convex polygons are convex spherical polygons. Physically, one can always interpret such a diagram as the result of tensions within the surface, with the centers of the cells being the “attractors”. Fig. 14.45 on the left shows a diagram determined by a set of randomly chosen centers on the sphere. Even though it already looks natural, the geometrical quality of the mesh can be significantly improved by letting the centers float such that they become the spherical barycenters of the corresponding cells. After just a few iterations, the cells are distributed much more evenly on the sphere.

Fig. 14.46 Different results of iteration processes with different numbers of cells. For 60 random cells, e.g., the result usually comes close to a “soccer ball” (12 pentagons, 20 hexagons).

Fig. 14.46 shows three results of such an optimization process for three different numbers of attractors on the sphere. Even though they are still almost on the same location as the randomized starting position, some numbers produce meshes on the sphere that strongly resemble some well-known figures.

14.3 Voronoi structures

585

In the image to the right, the result comes very close to a “soccer ball” (a projection of the corresponding Archimedian solid). ◂◂◂ ▸▸▸ Iterated Voronoi diagrams as a tool to find good point distributions Obviously, this method is an extremely useful tool for the numerical determination of point distributions on curved surfaces. It is also likely to be a principle of nature, affecting, for instance, the distributing of macro structures on the skin of animals.

Fig. 14.47 A caterpillar. With some imagination we could recognize a cylindrical shape on the left and the shape of a torus on the right.

For example, the venomous hair of some caterpillars (Fig. 14.47) serves as a layer of protection against predators. The following principle is essential from the perspective of the caterpillar: How should the hair on its body be distributed to provide optimal protection?

Fig. 14.48 Randomly distributed points on a cylinder and final (non-trivial!) equilibrium

Let us approximate the caterpillar’s body using a cylinder of revolution (image on the left) and that of the rolled-up caterpillar with a torus (image to the right). Two further examples (Figure 14.50 and Fig. 14.51) shall illustrate that the conclusion “Voronoi is everywhere” is not far-fetched. ◂◂◂

586

More applications

Fig. 14.49 Randomly distributed points on a torus and final equilibrium

Fig. 14.50 Are meshes on an armadillo Voronoi diagrams?

Fig. 14.51 Does a sea star produce Voronoi diagrams?

14.3 Voronoi structures

587

▸▸▸ Voronoi diagrams in 3-space Finally, the concept of Voronoi diagrams can be extended to three-dimensional space: We choose a number of cell kernels (this may, for instance, happen by random chance), and let the faces of each cell (which are always convex) lie in the symmetry planes to the neighboring kernels (Fig. 14.52 on the left). Again, we can improve the “evenness” or “balance” of the diagram by replacing the originally chosen kernels with the barycenters of the generated cells. If we repeat this procedure a few times, the diagram converges towards an optimal result (Fig. 14.52 to the right). These diagrams, which are defined purely mathematically, come close to “real foam” – their structure merely depends on the first set of kernels that are selected.

Fig. 14.52 Creation of an optimized three-dimensional Voronoi diagram. Left: random start. Right: equilibrium after several iterations.

As part of an experiment, foam was generated within a plastic cube, which produced a structure reminiscent of a Voronoi diagram. First, the cell kernels were distributed unhomogeneously (Fig. 14.53 to the left), and after longer periods of time, the foam slowly reorganized itself into a larger and more stable mesh (Fig. 14.53 on the right).

Fig. 14.53 Foam in a small cube is reorganizing itself into a stable mesh.

588

More applications

Fig. 14.54 Sculpture in the Austrian Alps

◂◂◂ An alternative algorithm Even though these are less geometrical, it shall be mentioned that, besides the “iterative Voronoi algorithm”, there are other algorithms that can be used to solve distribution tasks. Fruchterman and Reingold, e.g., proposed an iterative force-directed algorithm for drawing graphs that exerts attractive and repulsive forces on the nodes in [2]: Nodes connected to each other through an edge attract each other, while repulsive forces are applied to all pairs of vertices. In each iteration the maximum displacement applied to a vertex is reduced such that the adjustment becomes finer over time. Since then forcedirected algorithms have found wide application in graph drawing (see [23]) and have also been adjusted for application in geometry (see, e.g., [25]).

14.4 Hexagons on a sphere

589

14.4 Hexagons on a sphere ▸▸▸ A compound eye under the magnifying glass

Fig. 14.55 Compound eye of a moth and an even closer look at it (REM photos, courtesy of Science Visualization, University of Applied Arts: Rudolf Erlach, Alfred Vendl).

Fig. 14.56 “Pro forma” compound eye of a millipede (left photo), a dragonfly’s highly developed compound eyes, which has thousands of facets (right photo). Note the different sizes of the facets: the denser they are, the better is the vision of the animal.

If we take a closer look at the compound eyes of insects (Fig. 14.55), we see a lot of hexagons. From a purely geometrical point of view, it is an impossible task to cover a sphere with exactly congruent hexagonal spherical tiles. As is so often the case, nature finds a pragmatic solution, where the condition

590

More applications

“exactly” is replaced by “as closely as possible”. Moreover, the surface that is covered is not always exactly spherical (Fig. 14.56). ◂◂◂ ▸▸▸ How to tile a sphere with hexagons and some pentagons Interestingly, if one is patient enough, it is possible to find pentagons on compound eyes (Fig. 14.57, circled in yellow).

Fig. 14.57 Detail of Fig. 14.55: There are a few pentagonally shaped facets on the compound of eye of an insect.

Fig. 14.58 Tiling the icosahedron recursively and then projecting the result on a sphere.

For an approximation of a compound eye, one can, therefore, work with refined Platonic solids like the icosahedron (Fig. 14.58): We place hexagonal grids over the twenty regular triangles of the icosahedron and project the result onto a concentric sphere. The result are “a lot of” hexagons on the sphere (with slightly different sizes) plus twelve pentagons that stem from the vertices of the icosahedron. A variation of this simulation (Fig. 14.59) additionally works with small spheres placed on the centers of the spherical polygons, and it looks quite convincing. ◂◂◂

14.4 Hexagons on a sphere

591

Fig. 14.59 From left to right, the tiling is refined, just as in Fig. 14.58. At the centers of the polygons, spheres are inserted, and these spheres intersect neighboring spheres.

Fig. 14.60 Hexagonal grids on a hemisphere

▸▸▸ How to tile a sphere exclusively with hexagons If we do not want to use pentagons, the task is more complicated. It is impossible to cover a sphere with hexagons of equal size, but what if we use different sizes? If this is possible, would the algorithm not only work on spheres but also on more general surfaces? Given the number of faces on a sphere (or hemisphere respectively), our approach may be the following: Find a set of more or less balanced distributions of the given points (this can be done via formulas or with the above mentioned algorithm), and then determine the spherical Voronoi diagram. We may draw our inspiration from a photo of a wasp’s honeycomb (Fig. 14.61). By interpreting the hexagons as pyramids with the center as apex (Fig. 14.62), we already get something that resembles a compound eye, or, if you prefer, a wasp’s honeycomb (Fig. 14.61). ◂◂◂ Fig. 14.64 shows a variation of Fig. 14.62, where the points are not chosen arbitrarily, but rather by means of mathematical functions. The result still looks quite natural and resembles Text ergänzen

592

More applications

Fig. 14.61 Wasp’s honeycombs.

Fig. 14.62 This image is reminiscent of compound eyes or wasps’ honeycombs.

Fig. 14.63 Remarkable variation of the centers of the cells

▸▸▸ How to cover a surface with squares or circles Singly curved surfaces can always be easily with meshes that result in an equilateral and orthogonal grid when the surface is developed. On doubly curved surfaces, however, we can never find a mesh consisting of “squares on the surface”. Nevertheless, modern geometry sometimes has to fulfill tasks that would have been considered as “unsolvable” in earlier times.

14.4 Hexagons on a sphere

593

Fig. 14.64 Remarkable variation of the centers of the cells

We want to find grids that fulfill the following two geometric conditions simultaneously: All lines (1) intersect orthogonally and (2) locally have an almost constant grid size in both directions. Principal curvature lines on doubly curved surfaces (Fig. 6.52, Fig. 14.66 on the left), e.g., fulfill the first condition, but not the second one. The forcedirected iterative algorithm that is used to find the solution shall only be sketched briefly. It is described in detail in [18].

Fig. 14.65 Surfaces on the left: no border rules. Surfaces on the right: grid closed “in one direction”

If the grid does not need to follow boundary rules, the degree of freedom allows the algorithm to produce meshes that almost precisely fulfill both orthogonality and aspect-ratio-preservation (Fig. 14.65, left). If the grid has to be closed “in one direction”, orthogonality can be fulfilled reasonably well, but the grid size varies considerably (Fig. 14.65, right and Fig. 14.66, center and right). Fig. 14.67 illustrates how well the algorithm works if there are no restictions to the border. In order to test the quality of the result, one can, for instance, inscribe circles into the grid of squares. In Fig. 14.68, the grid is not visible at all; only the circles are drawn.

594

More applications

Fig. 14.66 Left: the exact solution of the curvature lines on an ellipsoid; center and right: two orthogonal grids with fewer restrictions

Fig. 14.67 A doubly curved surface is covered by a near-othogonal grid.

Fig. 14.68 A doubly curved surface (in this case a cyclid) is covered by circles.

Fig. 14.69 Orthogonal grids are aesthetically pleasing.

Even though these are not geometrically perfect solutions, architects and designers might be happy with the result (Fig. 14.69). ◂◂◂

595

14.5 Fractals

14.5 Fractals The term fractal was coined in 1974 by the mathematician Benoît Mandelbrot, who uses it to label certain naturally occurring or artificial objects and geometrical patterns ([20]). Basic properties of fractals are “self-similarity” and “scale invariance” (that is, you can zoom in any number of times and the fractal still looks the same at each scale).

Fig. 14.70 Koch snowflakes and clouds

▸▸▸ The Koch snowflake The classic example of a fractal in the strictly mathematical sense is the so-called Koch snowflake (Fig. 14.70, Fig. 14.71).

Fig. 14.71 Fractal curves have a dimension somewhere between one and two. Here, the Koch snowflake (dimension 1.26) is becoming increasingly two-dimensional.

596

More applications

Fractal curves have a dimension somewhere between one and two (since their shape never fills the whole surface). Fig. 14.71 shall illustrate that. Just to give an example, which you need not understand: The Koch snowflake has a fractal dimension of 1.26, which is quite close to 1 but can still be difficult to grasp. ◂◂◂ ▸▸▸ Plane-filling curves of dimension two

Fig. 14.72 Hilbert curves increasingly fill the plane with each iteration step.

Fig. 14.73 Hilbert curves can be created with different patterns (but always using the same system).

In 1891, David Hilbert discovered a curve that will eventually fill 2-space completely through folding and bending (Fig. 14.72, Fig. 14.73), and therefore, has a “fractal dimension” 2. ◂◂◂ ▸▸▸ Soft coral (gorgonia) A biologist will immediately think of some soft corals (“sea fans”), where flat skeletons are formed from a flexible, horny substance called gorgonin.

597

14.5 Fractals

The skeleton provides space for polyps with tentacles, which catch plankton and particulate matter for consumption (filter feeding). Obviously, the more space-filling the skeleton is, the better the food supply is (Fig. 14.75).

Fig. 14.74 Soft coral (gorgonia) during the day

Fig. 14.75 Soft coral (gorgonia) at night: The polyps catch plankton with their tentacles.

It must be emphasized again that nature does not always obey perfect mathematical rules. Evolution develops its own rules which are very often reminiscent of what mathematicians come up with. The goal of the process, however, is the same for Hilbert curves and gorgonia fans. ◂◂◂ ▸▸▸ Camouflage in coral environments What might be the purpose of the fairly similar surface-covering lines on the tumphead wrasse (Fig. 14.76)? Well, as this fish is active by day and often hides within corals, the most probable explanation is camouflage. ◂◂◂ ▸▸▸ Fractals on spheres and similar surfaces The surface of the humphead wrasse is not entirely flat, but the concept of filling 2-space also works on curved surfaces, e.g., on a sphere (Fig. 14.77,

598

More applications

Fig. 14.76 In between the Gorgonia, a humphead wrasse is hiding. Maybe the fractal-like patterns on its skin serve to conceal the fish.

Fig. 14.77 Left: Hilbert curves on a sphere. Right: brain corals often possess spherical shapes. The similarity is undeniable.

Fig. 14.78 Increasing the depth of iteration on the sphere

left). Brain corals (some species of hard corals) have such patterns on them (Fig. 14.77, right).

14.5 Fractals

599

To provide, once again, an idea of how the iteration works, Fig. 14.78 shows the first four iteration steps. ◂◂◂ ▸▸▸ The Mandelbrot set (Fig. 14.79) It was only in the 1980s that fractals reached their current level of popularity with the impressive pictures by Benoît Mandelbrot. The first computers with the capacity to display graphics enabled the aesthetically fascinating visualization of hitherto unknown fractal worlds.

Fig. 14.79 The famous Mandelbrot set. Left: A bounded sequence leads to a “good point”. Right: Here the chosen sequence is not bounded.

Let us consider the complex function f (z) = z 2 +c. Then, we define a sequence of complex numbers z0 , z1 , z2 , . . . as follows: z0 = 0, z1 = f (z0 ) = c, . . . , zn+1 = f (zn ) = zn2 + c. If the sequence zn remains bounded (Fig. 14.79 left), then the number c is considered to be “good”, and we mark it with a black or blue point in the Gaussian plane. One can say that the Mandelbrot set is the set of all parameters c for which the recursion zn+1 = zn2 + c remains bounded if one chooses z0 = 0. ◂◂◂ ▸▸▸ Julia sets Julia sets (named after Gaston Julia, who investigated the behavior of those sets decades before the computer age)can be created with the same recursive formula as the Mandelbrot set. Instead of choosing z0 = 0, however, z0 can be any point in the Gaussian plane. When one chooses, for instance, a point z0 along the border of the Mandelbrot set (Fig. 14.80), the shape of the corresponding set changes rapidly. With some imagination, one may be reminded of the rapidly changing Julia sets when we look at the huge fire in Fig. 14.81 and the clouds in Fig. 14.82 – even though, of course, they are no mathematical structures. It is, furthermore, remarkable that such natural shapes often change permanently and there is no clearly recognizable contour. ◂◂◂

600

More applications

Fig. 14.80 Julia sets with starting points z0 close to the border of the Mandetbrot set. The shape of such a set somehow resembles the “local shape” of the Mandelbrot set.

Fig. 14.81 Solstice fire or Julia sets?

Fig. 14.82 Clouds or Julia sets?

601

14.5 Fractals

▸▸▸ Tree fractals

Fig. 14.83 Tree-branching in practice

Fig. 14.84 The Pythagorean figure is adapted and used for the generation of fractal tree-like figures.

In Fig. 14.84 on the left, the Pythagorean figure is repeated in fractal-like manner (recursive scaling). The resulting figure shows no sharp contour line as the depth of the recursion grows. Zooming in does not change this. A nice generalization can be found in the model Fig. 14.84 on the right, which was designed by F. Gruber and G. Wallner. Fig. 14.83 shows a “real tree” in all its beauty. ◂◂◂

602

More applications

Fig. 14.85 Trees and clouds

▸▸▸ Ferns The computer graphic in Fig. 14.86 on the left is based on an idea by Michael Barnsley according to which the algorithm repeatedly applies one of four (exactly defined) affine transformations to a single point. This iterative procedure moves the point continuously, producing a fractal of this kind (https://en.wikipedia.org/wiki/Barnsley_fern).

Fig. 14.86 Fern in theory and practice

A fern is a good example of a fractal-like structure in nature. Take a look at the computer-generated shape of Barnsley’s fern: Most botanically knowledgeable observers will correctly identify it as a fern and agree with its fractal designation, as the basic structure repeats itself over and over again at different scales. Let us now consider the photograph of an actual fern (Fig. 14.86 on the right). Here, the fractal nature is not as clear as in the computer simulation. After the second iterative step, the self-similarity is hardly recognizable. If the bottom side of the fern leaf is magnified many times over, it becomes clear that the fanning-out of the fractal-like leaf structure serves

14.5 Fractals

603

the purpose of covering the maximum possible area with sporangia. It is also a good strategy for optimizing photosynthesis. ◂◂◂ ▸▸▸ Fractal expansion

Fig. 14.87 Fractal expansion (“string of pearls”): algorithm filling the plane in a fractal manner.

Let us consider the following algorithm (Fig. 14.87): A circle is given at the start. We now create a second circle within a given rectangular boundary and keep moving the new circle towards the old one until they touch each other. Now, a third circle is introduced at a random location. If it is closer to the first circle, it is moved towards it by the same procedure as before. Otherwise, it is moved likewise towards the second circle. After many circle generations of this kind, a tattered sort of “string of pearls” is produced, which branches out at several points. This algorithm tends to fill the plane in a fractal manner. However, nature probably does not follow this exact recipe.

Fig. 14.88 The eye of a crocodilefish: A fractal pattern works as camouflage.

604

More applications

Areas that are filled in a non-regular manner are often encountered in the natural world. For instance, in the growth of lichen or in camouflage effects. Figure 14.88 shows the magnified eye of a crocodilefish (Cymbacephalus beauforti). ◂◂◂ ▸▸▸ The Menger sponge Fractals can also be created in 3-space: A simple example of that is the construction of a so-called Menger sponge, which can be described as follows (Fig. 14.89 and Fig. 14.90):

Fig. 14.89 Fractal in 3-space (Menger sponge): With each iteration, each existing cube is transformed into 20 smaller cubes.

Fig. 14.90 Next iteration: One can see that the space is not entirely filled. We will not provide an explanation, but mathematicians say that the sponge’s dimension converges to ≈ 2.73.

Take a cube C0 and divide it into 3 × 3 × 3 = 27 smaller cubes C1 of equal size (by dividing every face of C0 into 9 squares). From the cubes C1 , remove the six cubes in the middle of each face plus the one in the very center of C0 . Repeat this procedure for all the remaining 20 cubes C1 . You will get a new structure with 202 = 400 cubes C2 , etc. ◂◂◂

605

14.5 Fractals

▸▸▸ Sierpinski fractals

Fig. 14.91 Sierpinski pyramid (physical model). Right image: multiple reflections in the spheres, each of them is a fractal of its own.

The “Sierpinski pyramid” (Fig. 14.91) is 40 cm tall, weighs 25 kg, and was built by Christoph Pöppe from metal spheres with the help of the IWR (Heidelberg University). Four spheres that are strung together produce a tetrahedron.

Fig. 14.92 Several iterations of rounded Hilbert curves in space.

Waclaw Sierpinski (1882-1969) also discovered a recursively defined sequence of closed curves that fills the plane in the limit. The sequence of figures in ◂◂◂ Fig. 14.92 shows various recursion levels of rounded Hilbert curves.

606

More applications

▸▸▸ Percolation

Fig. 14.93 We divide a cube into tiny voxels and randomly “occupy” a certain percentage rate of those cubes. What is the threshold at which we get a closed random path from one side to the opposite one?

If we consider a cube, divide it into tiny cubes (voxels, i.e., the three-dimensional analogue of the two-dimensional pixel), and randomly “occupy” a certain percentage rate of those cubes, the others stay empty (Fig. 14.93). Finally, we just consider strings that are coherent. What percentage of the cube cells must be occupied on average so that there is a continuous path from one side of the cube to the other side? In other words, at what point is there a connected path of cells from the top of the cube to the bottom? This percentage is called the percolation threshold.

Fig. 14.94 Below the percolation threshold (image to the left) and above the threshold (image to the right).

If a cell is occupied with probability p, the size of the clusters increases with increasing p (Fig. 14.94). If p increases beyond a certain threshold, the largest cluster will permeate the entire system from top to bottom as well as from left to right and back to front. The sponge-like structures are reminiscent of voxel models of complex forms. ◂◂◂

A

Geometrical freehand drawing

This appendix is intended for people who believe – as I myself do – that, despite the quality of today’s computer “renderings”, correct freehand drawing is still of principal importance for geometric communication. I would even go a step further than that: Because perfect computer renderings are state of the art, great freehand drawings are becoming an increasingly rare and therefore, increasingly impressive skill! This appendix is written so that it may be read before acquiring the knowledge contained in the rest of the book. We will, from time to time, make reference to previous contents, but even without these references, the course is largely self-contained. This should permit a “geometric layperson” to produce qualitative correct drawings within a short period of time. There is a simple but useful saying that goes as follows: “When a problem takes till dawn, an auxiliary figure must be drawn!” As a first step, the solution should be inscribed into this auxiliary figure. The more useful this figure thus becomes (due to geometrical correctness), the easier it is to figure out which steps must be undertaken in order to reach the existing solution. Many drawings in this appendix were done by the participants of my course about “artistic perspective”. A lot of them received a final artistic finish by Christian Perrelli. An experienced eye may even detect slight errors in the drawings: This, too, contributes to the charm of freehand drawings, and owes much to their origin in our imperfect imagination – and besides, we have already seen enough perfect renderings anyway. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3

607

608

A course in freehand drawing

A.1 Normal view vs. oblique view In this appendix, we shall illuminate three types of visualization in more detail: the oblique view, the normal view, and the perspective view (central view) – the latter being far more difficult than the oblique and the normal views.

Why the oblique view is not our ultimate goal The section about the oblique view will be the shortest by far.

Fig. A.1 A house, a cube with inscribed circles, and a sphere in the oblique projection

Most people have drawn oblique views at some points in their lives. Most probably oblique projections, also called front views: Assuming a non-distorted frontal view, images of polyhedral forms are thus easy to construct. Straight lines proceeding towards the back are drawn at a constant angle α (such as α = 45○ ), and depths are always shortened by the same factor (e. g. by a half). Thus, the image of a house is quickly constructed by means of a cuboid (Fig. A.1 on the left). What’s more, it is easily possible to inscribe the images of circles into the images of squares, as in Fig. A.1 at the center. The images of the foremost and the backmost circles remain circles. The ellipses appearing as the images of the other circles are each defined by the four edge midpoints and the edges’ images are tangents there. However, it should be noted that the vertices of the ellipse are not known. It is further not easily possible to specify the contour of a sphere, and if we simply inscribe it without construction (Fig. A.1 on the right), then it is surely wrong! A second approach to producing visually transparent oblique views is based on building objects above their undistorted, oblique top views (for instance, with an angle α = 30○ ). The results of this method can be seen in Fig. A.2. The heights are either shortened (by half, for instance) or undistorted. This yields a bird’s-eye view. In the case of cubes with circles inscribed onto their faces, the lowest and the highest circles are undistorted, and the remaining ones are displayed as

A.1 Normal view vs. oblique view

609

Fig. A.2 A house, a cube with inscribed circles, and a sphere in bird’s-eye view

ellipses bounded by circumscribed parallelograms. As before, the axes of the ellipses are unknown. Spheres leave us with the same problem as before. As practical and as easily explicable as the above-mentioned approaches are, they all share a severe disadvantage: The usual oblique views (frontal projection and bird’s-eye view) yield undistorted images. Thus, they are ill-suited to visualize spheres and other surfaces of revolution.

Isometry In theory, given an oblique view, one may freely choose the images of the coordinate axes and the distortion ratios along them. These assumptions relatively successfully compensate the aforementioned disadvantage. Let us start with a special assumption which produces a normal view, the socalled isometry: Here, any pair of the axes’ images encloses an angle of 120○ , and all segments in the direction of the coordinate axes remain undistorted. (Actually they are equally distorted, since isometry literally means “equal metric”.)

Fig. A.3 A house, a cube with inscribed circles, and a sphere in isometry

610

A course in freehand drawing

In Fig. A.3, our test objects are displayed isometrically. The house now appears to be “more realistic,” and the sphere on the right now possesses a circular contour, which is obviously the most significant improvement. The depiction of the cube now has the disadvantage that the images of two opposite vertices of the cube coincide at the center of the image. The ellipses appearing as the images of circles are even congruent. The principal axes of the ellipses are orthogonal to the images of the coordinate axes, which gives the artist a great advantage during construction, because the symmetry axes of the ellipses are known. Due to the strict definition of the axis angles, isometry leaves no choice when depicting an object. The horizontal base plane is always seen at the same angle. Let us summarize: Isometric depictions are well-suited for quick and transparent sketches of polyhedral as well as round bodies, as long as they are not exactly like cubes. However, they permit little variation of the viewing angle.

Fig. A.4 Isometry of an icosahedron (on the right: Sophie’s spaghetti model)

As an exercise, let us draw the isometric view of an icosahedron. Without prior knowledge about its geometric construction, such a body is practically impossible to draw. However, If one is aware that an icosahedron may be defined by three mutually orthogonal “golden rectangles” (side ratios of ≈ 8 ∶ 5), then an optimal isometric view may finally be attempted with confidence.

The advantage of a normal projection From theory, we know that images of axes may be chosen (almost) freely. In this case, there always exist precisely defined distortion ratios for each axis direction, by which a normal view, and not just a general parallel view, may be accomplished. The advantage: Each normal projection depicts circles as ellipses which are symmetrical to the image of the circle axis and sphere contours are circles. This means that the objects in view appear natural.

A.1 Normal view vs. oblique view

611

In general, one deals with three different distortion ratios for the three axis directions. Apart from the increased difficulty of constructing objects in such a way, the determination of these ratios requires a construction which a freehand artist cannot do with an adequate enough amount of accuracy. We are already aware of a very special type of normal projection: isometry. There, all distortion ratios are identical (1 ∶ 1 ∶ 1) due to equal angles enclosed by the images of the axes. This makes the application of distortion ratios unnecessary, since the result would just be scaled. However, there exist other choices of angles between the images of the axes which correspond to very simple distortion ratios.

The engineer’s view – dimetrical and descriptive If one tries to find those angles between the axes where where the distortion ratios correspond to specific values, such as 1 ∶ 1/2 ∶ 1, then the image of the y-axis, for instance, must deviate from the horizontal axis by slightly less than 45○ – by about 42○ , to be precise. The image of the x-axis and that of the z-axis are symmetric to that of the y-axis due to identical distortion ratios along the x- and z-direction. The image of the x-axis thus deviates from the horizontal by about 7○ (Fig. A.5).

Fig. A.5 A house, a cube with inscribed circles, and a sphere in the engineer’s view

This configuration is known as the engineer’s view and offers similar advantages to isometry, but it is also well-suited for “cube”-shaped objects (Fig. A.5 at the center). Of course, there also exists a symmetric solution where the xaxis forms the aforementioned 42○ . The distortion ratio along the x-direction is thus about one half, while there is distortion at all in the y-direction.

The general solution The engineer’s view is also a well-defined normal view. Should neither isometry nor the engineer’s view provide a “useful impression” of a specific object, then there is also a general method that, even in freehand drawing, yields relatively accurate results. Prior to drawing, we can give good estimations of the results, which gives the artist an additional advantage: Our desire is not to determine what technique works best by “trial and error”, but to proceed towards our goal in an economic way. One starts with the image of a unit circle in the horizontal base plane (midpoint U , radius 1 unit). The principal axis of the ellipse that is the circle’s

612

A course in freehand drawing

Fig. A.6 Different images of the unit circle

image is orthogonal to the image of the z-axis according to the rules of normal projection (Fig. A.6). Depending on how “bulgy” the circle’s image is, the base plane is more or less oblique. In the next step, the image of the x-axis is chosen arbitrarily. The image of the y-axis is given automatically by the third step: There exists a circle tangent t where the x-axis intersects the unit circle (point X) – in the image, it is a tangent to the ellipse. Since the horizontal tangent t is orthogonal to the x-axis (both considered as lines in space), it is parallel to the y-axis. The y-axis intersects the unit circle at the point Y . The segments U X and U Y are the “unit segments” on the axes. This already makes it possible to inscribe arbitrary figures onto the base plane. If the images of a horizontal circle and one horizontal axis direction are given, then the image of the missing horizontal axis direction and the distortion of the top view are also defined. What still remains to be determined is the degree by which the heights are distorted. From a qualitative point of view, we can state the following: The more bulgy the ellipse (image of the base circle) is (axis lengths 2a = 2r and 2b), the more the z-values are shortened. This statement is instantly quantifiable, since we already know the silhouette of the unit sphere about U – it is the circle about U ’s image that touches the image of the unit circle in the principal vertices.

Fig. A.7 General views of the globe

A.1 Normal view vs. oblique view

613

The unit circle is the equator of the sphere. By analogy, we can inscribe the sphere’s zero meridian through the point X. Its axis is the y-axis, and the principal axis of its image is orthogonal to the image of its axis – as in the case of the equator. The position of the point X determines the “bulginess” of the ellipse that is the meridian’s image. The image of the North Pole Z can be found at the intersection of this image ellipse with the image of the z-axis. U Z is the unit segment for the y-coordinates. (For those interested: One can also find the image of the North Pole by pivoting a focal point of the image of the unit circle by 90○ or by intersecting the sphere’s silhouette with the parallels to the image of the z-axis at a distance of ±b (semiminor axis of the equator’s image) – the North Pole has the same height.) A general normal projection is best defined by the image of the unit sphere’s equator. By inscribing the sphere’s zero meridian, one can determine its north pole and thus, one has full control over all distortion ratios. In order to consolidate the aforementioned in our minds and improve our skill of drawing ellipses, we shall now sketch general views of the globe (Fig. A.7). This type of “construction”, which considers the right distortion ratios, has the advantage that we can specify the direction from which the drawn object is viewed. The images of the equator and the zero meridian of the unit sphere give a good impression of what the rest of the image looks like. Such a test sketch can also be drawn for the image of the “unit cube.” ▸▸▸ Circles with axes parallel to the coordinate axes Let us sketch a scene that consists of several cylinders of revolution (Fig. A.8).

Fig. A.8 Standing and lying cylinders of revolution

The images of the top circles of an upright cylinder of revolution are always ellipses whose principal axes are orthogonal to the image of the z-axis. Lying cylinders are to be depicted in the same way:

614

A course in freehand drawing

• The images of the boundary circles are ellipses whose principal axes are orthogonal to the image of the axis of the cylinder. • The diameter of the cylinder is equal to the length of the principal axis. • The search for another further image point will show how bulgy the circles’ images actually are. If, for instance, the bottom cap or the top cap lie in a plane parallel to the yz-plane, then such a point can be found by parallel translation of the images of the y- and z-axes through the principal vertices of the ellipse that appear as the circle’s image. ⊕ Remark : This construction is plausible: Let A and B be those endpoints of a diameter of the circle k whose images are the principal vertices of the ellipse k n . The two axes y and z are orthogonal lines in space, so that the intersection of the parallels through the endpoints A and B lies on k according to Thales’s theorem. We thus get a point on the ellipse that appears as the image of k. In cases of symmetric axis positions, we have also found the auxiliary vertices of the circle’s image. ⊕ ◂◂◂

A.2 Don’t be afraid of curved surfaces

615

A.2 Don’t be afraid of curved surfaces Unfamiliar at first. . . Freehand drawing is strange at first: Instead of employing a ruler at every turn, we force ourselves to draw straight lines by hand. No doubt, we would also feel more confident if our circles were made with the help of a compass. It does, in fact, require a considerable amount of experience to make a freehand drawing of a circle with a given radius.

. . . but soon highly advantageous! Except for sphere contours, perfect circles rarely occur in freehand drawing. One most often deals with ellipses and is thus, as a freehand artist, at a definitive advantage compared to those who have to rely on rulers and compasses. The true advantage lies in the fact that – with some spatial imagination and geometric aptitude – we can quickly surmount many obstacles that would needlessly occupy a “constructing” artist for a much longer time. Furthermore, it is often in in hindsight, only after the result has been “estimated” in a sketch, that an exact construction seems to be much easier. Freehand drawing that is based on geometric facts is an important aspect of the later derivation of exact solutions. In light of this, every person that deals with geometry should be trained in this craft even in the absence of any artistic aspirations.

It does not get any more difficult The next advantage is that the transition from polyhedral building blocks to elegant, curved surfaces can happen smoothly – no pun intended – without an apparent increase in the degree of difficulty. During construction with a ruler and a compass, we quickly hit a brick wall and usually fail due to our “tools”! During freehand drawing, however, we may concentrate on our geometrical thinking. ▸▸▸ One-sheeted hyperboloid of revolution The surface can be generated by the rotation of a straight line about a skew axis. There exists a second family of straight lines on the surface. The contour and the two families of straight lines are to be depicted. Let us start with a horizontal base circle, which we want to subdivide into eight equal parts. This may be done by first selecting an arbitrary x-axis. The orthogonal y-axis is parallel to the tangents of the x-axis points on the

616

A course in freehand drawing

base circle. The two axes define a square which is circumscribed to the circle. Along with the coordinate axes, its diagonals yield the evenly distributed points 1, . . . , 8 on the base circle.

Fig. A.9 Variations of a one-sheeted hyperboloid of revolution

Let us depict a congruent cap circle at an arbitrary height. Then let us keep the eight points but shift the labels by, for instance, three points. This yields eight straight lines on the surface and eight tangents of the contour hyperbola. By lifting the eight points into the other direction, we may derive eight further tangents. Thus, the contour seems to be adequately defined. During the final composition of the image, one should consider that a change of visibility occurs at the contour. A variation may be given by using the affine mapping of the base circle image with the undistorted circle position. A circle may easily be decomposed into equal parts. ◂◂◂ ▸▸▸ Beam connection Two recumbent cylinders of revolution with equal radii and orthogonally intersecting axes are to be depicted. (Fig. A.10) Let the x- and the y-axis be the axes of two cylinders. It helps if the images of the axes of the cylinder axes are chosen as unsymmetrical as possible relative to the image of the z-axis, just as in the engineer’s view. There is a sphere inscribed to both cylinders simultaneously, which is centered at U . We shall try to depict this sphere first. The contour generators of both cylinders touch the circular contour of the sphere. Let us cap them off with circles by picking their midpoints on the cylinder axes at arbitrary positions. The principal axes of the corresponding ellipses that represent circles in the image are orthogonal to the images of the cylinder axes. Further points may be derived by a parallel translation of the axes.

A.2 Don’t be afraid of curved surfaces

617

Fig. A.10 Beam connection

The intersection of the cylinders consists of two congruent ellipses. One must consider that an arbitrary (non-circular) ellipse in space may also be depicted as an ellipse, but that, in general, no axis of the ellipse will be orthogonal to the image of any coordinate axis. Thus, the objective will consist of determining as many points and tangents of the ellipse as possible. Let us consider the highest and the lowest generators of both cylinders. They intersect each other in two points, C and D. The generators which lie in the xy-plane intersect in the points A1 , A2 and B1 , B2 , which are symmetric with respect to the origin. At those locations, the ellipses which form the intersection of the cylinders possess z-parallel tangents. C and D belong to both ellipses. The corresponding tangents are parallel to A1 B1 and A2 B2 . As an additional information, it should be considered that the ellipses’ images touch the contour generators of the cylinder. The respective contact points are of great importance, because they mark the transition from the visible to the non-visible part of the curve. ◂◂◂ ▸▸▸ Pencil tip (Fig. A.11) A regular hexagonal prism is to be conically “tapered” (which happens when the pencil is sharpened). The vertical faces of the prism will intersect the cone of revolution along the hyperbolas. We shall, at the very least, locate the highest points of these hyperbolas. Let us choose the horizontal base circle of the cone of revolution, into which we shall inscribe a regular hexagon. The tip may be chosen arbitrarily on the z-axis. The tangents from the image of the tip to the image of the base circle are the contour generators of the cone. The choice of the x-axis (point X on the circle) entails the direction of the y-axis (parallel to the tangent in X). This time, the images of the axes may very well be symmetric. We can derive

618

A course in freehand drawing

Fig. A.11 Pencil tip

the neighboring points of the hexagon, relying on a well known property of the regular hexagon, by intersecting the y-parallel with the circle through the midpoint M of U X. The remaining points are given by mirror-symmetry with regard to U . In the yz-plane, the highest point H of the section hyperbola can be constructed directly: It lies precisely above the side midpoint and on the generator of the cone. All other vertices are located equally high above the remaining midpoints of the sides. The corresponding tangents are parallel to the hexagon sides. During sketching, one should take into account that two of the six arcs touch the contour of the cone and change from the visible to the non-visible part of the surface. The pencil lead shares a circle of intersection with the cone, which is located at the appropriate height and is coaxial with the base circle. ⊕ Remark : During freehand drawing, as well as during precise construction, one may always stumble upon inconvenient perspectives (such as projecting intersections). For instance, the drawing attempt in Fig. A.11 on the left may not be optimal. One may be consoled by the fact that freehand drawing tends to be quick. There is never a lot of time lost, and one can, therefore, easily start anew. ⊕ ◂◂◂

▸▸▸ Helical stairs (Fig. A.12) In a front view, a helix with an upright axis appears as a sine curve. It is easy to draw such a curve: It is created by means of a harmonic oscillation and a simultaneous uniform translation in an orthogonal direction. Let us draw such a curve. In order to simplify our task, let us also draw the contour generators of the carrier cylinder. The axis of the cylinder appears as the mid-parallel of the two contour generators (Fig. A.12 on the left). The curve’s period length equals the pitch of the helical motion. As an exercise, let us also depict a second helix, which is created by reducing the radius of the original helix to about a quarter. It appears as a sine curve with the same

A.2 Don’t be afraid of curved surfaces

619

Fig. A.12 Normal view and front view of varying helices (helical stairs)

frequency but a smaller amplitude. In Fig. A.12 at the center, a variation of the original is visible: a helical staircase appears on the right. In order to accomplish roughly 16 equally distributed points on the helix, we choose the planes that correspond to a height difference of 1/16 of the pitch. The 16-part subdivision can be found during construction by repeatedly halfing ◂◂◂ the pitch. ▸▸▸ Surfaces of revolution Surfaces of revolution may be produced by a rotation of the meridian during which the points on the meridian move on the circles of latitude. Tangents of the meridian circle generally generate cones of revolution with their apices on the axis of rotation. (In some cases, the cone degenerates to a cylinder of revolution which is coaxial with the surface of revolution. The cone may also collapse to a plane which is orthogonal to the axis of rotation.) In order to sketch the given surface of revolution in a visually accurate way, it is paramount to first inscribe the meridian along with the axis of rotation (Fig. A.13 on the left). Or, for the purpose of control, the symmetric meridian may be included. We denote special points on it: These include, above all, the points with axis-parallel tangents but also any inflection points which may arise. The tangents in the boundary points are also important. The normal views of the respective circles of latitude are now drawn in the normal projection (Fig. A.13 on the right). The respective heights are shortened in relation to the obliqueness of the axis. If the obliqueness is only slight, one may even use the same heights during freehand drawing. We use the images of the apices of the cones to draw the tangents at the ellipses that are the images of the corresponding circles of latitude. The contact points correspond to the contour of the surface of rotation – the tangents of the ellipses are also tangents of the outline of the surface. At the points with minimal

620

A course in freehand drawing

Fig. A.13 Surfaces of revolution: a torus can be seen on the right.

or maximal distance from the axis of rotation (where touching cylinders of revolution occur), the principal vertices of the image ellipse are the contour points of the surface. ◂◂◂ ▸▸▸ Blossom of a lily

Fig. A.14 Blossom of a lily

Advanced or the artistically ambitious may try their hand at the following example: A bell-shaped surface of revolution (Fig. A.14) should be “serrated” so that something similar to a bellflower or lily emerges – and since nature itself rarely produces absolutely perfect surfaces, we are allowed to be a little bit imprecise in our freehand drawing. Nevertheless, it is advantageous to first sketch the surface of revolution without the indentations and thus determine the silhouette. In another step, we subdivide the boundary curve into five approximately equal sections (nature seems to have a penchant for five-fold symmetry) and

A.2 Don’t be afraid of curved surfaces

621

estimate the corresponding meridian A through the points 1, . . . , 5 of the subdivision. In a last step, we inscribe the circle of latitude, which shall limit our indentations. The midpoints of the points defined by the intersections with the special meridian are the endpoints B of the section lines. These points are now carefully connected to the starting points A. The images of the section curves may touch the silhouette in some cases. If parts of the original silhouette of the surface of revolution remain, they may form the silhouette of the flower. ◂◂◂

622

A course in freehand drawing

A.3 Shadows In order to give our freehand sketches a realistic appearance, we may now add shadows, but we must proceed carefully: Shadow constructions are complicated and, therefore, “dangerous.” A realistically drawn false shadow can do more damage than good for a better understanding of the image. We shall thus limit ourselves to shadows of simple scenes. Furthermore, it is better to start one’s shadow exercises with sunlight (parallel shadows), rather than using light sources directly within the scene. Convex bodies possess neither ridges nor indentations. Thus, they do not cast shadows on themselves. Cuboids, cylinders of revolution, and cones of revolution are simple examples. For these three prototypes, we shall now attempt to sketch parallel shadows in simple scenes. ▸▸▸ Parallel shadows of a cuboid

Fig. A.15 Cuboid with shadow

Let us choose the light position, ideally, by choosing the shadow Ps of a point P of the top surface. Then, all light rays are parallel to the direction P Ps . Furthermore, all top views of the light rays are parallel to the connection of the top view P ′ of P with the shadow Ps in the base plane. Thus, we can construct the shadow of a further point Q of the cap surface by drawing the parallel to the light ray through Q and the parallel to the light ray’s top view through Q′ . The triangles P P ′ Ps and QQ′ Qs are similar in any case and even congruent in the special case of equal heights. P Q and Ps Qs should be parallel and of equal length, because P is parallel to the base plane. (The “light plane” through the edge is intersected by two parallel planes.) The shadow provides important information about the cuboid’s penumbra. We will try to rely on our spatial imagination during its construction.

623

A.3 Shadows

⊕ Remark : A little hint for the shading of a cuboid: Surfaces in penumbra are “slightly darker”, but they, nevertheless, exhibit surface texture (such as that of a building wall). Shadows, on the other hand, are “no longer aware” of their origin, exhibiting the texture of the surface on which they are cast (such as a lawn or asphalt). ⊕ ◂◂◂

▸▸▸ Parallel shadows of cylinders and cones Shadows of cylinders of revolution and cones of revolution are almost as easy to draw as those of cuboids: Their contour with regard to any projection (parallel or central) consists of straight parts. The direction of the light can

Fig. A.16 Cylinder and cone with shadow

be given by defining the shadow of the center M of the cap circle or the cone’s apex S. In this way, we once again obtain the characteristic triangle, which can be employed for the construction of further shadow points. In the case of the cylinder of revolution, the shadow of the cap circle should be centered at the shadow Ms of M : It is congruent to the image of the cap circle. The common tangents of the elliptic image of the base circle and of the shadow of the top surface provide the straight-line component of the shadow boundary. The penumbral shadows that are parallel to the axis start in the contact points with the base circle. In the case of the cone, one only needs to draw the tangents to the image of the base circle from the shadow Ss of the apex S in order to obtain the straight shadow boundaries. From the contact points, the straight penumbral boundaries then run towards the cone’s apex. ◂◂◂

624

A course in freehand drawing

A.4 Perspective sketching There is an entrance exam for the University of Applied Arts Vienna where, among other parameters of artistry, the drawing skills of the applicant is to be determined. Years ago, it used to include the following exercise: The applicants had to sketch a staircase inside the University. Fig. A.17 shows a fisheye photograph of this staircase (from above). Is it actually possible to sketch the staircase correctly?

Fig. A.17 Overview with the fisheye lens, general and special perspective image

Reducing the level of difficulty A wide-angle photograph can be seen in the middle. The task seems to be quite complex, and we may not even notice slight errors in the sketch. It would surely do no harm to simplify the view slightly (as in the picture on the right). No examiner would require that every point be geometrically transparent on a candidate’s first attempt. However, systematic considerations may well improve the result.

The method of Renaissance artists Perspective images are the result of a central projection from an eye point to the image plane. This serves to simulate the impression of natural sight. In a simple wood engraving, Albrecht Dürer showed his contemporaries, as well as the generations that would follow, how lines of sight may be intersected with the image plane: The viewing ray appears with the help of a taut thread through a loop E – the eye point. One person places the thread at the point that is to be displayed. Another person marks the intersection point with the image frame by means of a crosshair. By closing the lid for a short period of time, the image point may be fixed.

The most important terms In order to proceed with our analysis, we need to employ some special “terminology”: The eye point E is located at a distance d in front of the principal

A.4 Perspective sketching

625

Fig. A.18 Wood engraving for the intersection method

point H of the perspective image. The straight line EH is the viewing axis or principal ray. A straight line parallel to the image plane π is called the frontal line, and a straight line orthogonal to π (and thus, parallel to the viewing axis) is called the depth line. The following theorem is important for drawing and applicable here: Perspective images of parallel straight lines intersect, with the exception of frontal lines. Depth lines vanish in the principal point. Frontal lines are very practical in perspective images: Affine ratios are preserved on frontal lines. The angle between two frontal lines remains undistorted in the perspective image. The horizontal plane on which we stand is called base plane. Its intersection with the image plane is called base line. The location of our feet is called standpoint, and the height of the projection center is called eye height. The horizon is produced when all points at infinity of the base plane are projected to the image plane. Thus: The perspective images of horizontal parallel straight lines intersect at the horizon. In cases of a horizontal perspective image, the horizon contains the principal point.

Frontal perspective image Let us now connect the scene to a Cartesian coordinate system with three axis directions x, y, and z. The xy-plane shall serve as the base plane. The z-axis is then upright. If the principal ray (the viewing direction) has the direction of a coordinate axis, the image plane is parallel to the respective perpendicular coordinate plane. This is called a frontal perspective. Two axes are frontal lines and span a frontal plane, in which figures are undistorted (Fig. A.19). The third axis is

626

A course in freehand drawing

Fig. A.19 Special positions of the coordinate system. On the left a frontal perspective painted by M. K. Steiner (see also p. 607). In reality, the painting is more than 1.5 m2 tall. If you position yourself one or two meters in front of the principal point (the “intersection” of the railway tracks), your brain is tricked into believing that you are actually there – slightly above the ground.

the depth line and vanishes in the principal point. Aside from the “contents” of the frame, Fig. A.18 is a classic example of frontal perspective. ▸▸▸ The “square-grid method” A method that was popular in the Renaissance approximated a complex top view by means of a square grid. Let us tile the base plane with square tiles, starting at the base line. This makes the sides of the squares either parallel or orthogonal to the image plane. In a perspective image, the image of this grid of squares is to be drawn as follows: Firstly, the points on the base line equal their perspective images, and secondly, the depth lines all vanish in H. We may still choose an arbitrary vanishing point D1 in a diagonal direction. The other vanishing point D2 is symmetric with respect to the principal point H.

Fig. A.20 Square-grid method: The classical method from the Renaissance (left). A wide-angle photograph which clearly depicts the vanishing points of the square diagonals. The photo exhibits a slight “barrel distortion”, which often occurs in lenses of a very short focal length (right).

The distance of the points D1 and D2 from H is equal to the distance EH of the image plane’s eye point. (We have drawn parallels to all 45○ straight lines through the eye point E.) For this reason, these points are called distance points.

627

A.4 Perspective sketching

We may now “interpolate” the top views of arbitrary points. The appropriate height may be drawn as follows: The top view is to be translated orthogonally to the base line (which – in the perspective image – equals a projection from H to g). Above the top view that was projected to g in this way, we may now measure the undistorted height and finally project it back. ◂◂◂

Perspective images with a horizontal viewing axis We no longer wish to look in the direction of a coordinate axis, but nevertheless, let the viewing axis remain in a horizontal position. The upright straight lines still remain as frontal lines, and their images are mutually parallel. The x-axis and the y-axis vanish at two points F1 and F2 on the horizon.

Fig. A.21 Subdivision of segments (special multiples)

Fig. A.22 Cuboid objects

Cuboid objects, which are positioned with many edges parallel to one coordinate axis (Fig. A.22), are very easy to sketch. Vertical segments should be drawn, as previously described, with the use of orthogonal projection to the image plane. They can also be easily subdivided. Yet, the following wish is not easily attainable in freehand drawing: the desire for exact drawing of segments along the coordinate directions. However, since there are simple methods for drawing affine ratios in a perspective view, this need not be a showstopper. Fig. A.21 shows how fast midpoints or the doublings of horizontal segments may be derived by drawing diagonals into overlying vertical rectangles.

Fig. A.23 General subdivision of segments

The general method is illustrated in Fig. A.23: An arbitrary auxiliary vanishing point B is to be selected on the horizon, and the segment P Q is to be translated on a parallel to the base line. The result is a segment P0 Q0

628

A course in freehand drawing

which can generally not be seen in an undistorted state, but which may be employed to inscribe the desired affine ratio. One may afterwards move back again. (This method works because it can be interpreted as a parallel projection in space.) ⊕ Remark : Consider the following hint: P0 Q0 is more likely to appear undistorted the nearer B is to the so-called measurement point of the segment (which is the vanishing point of the rotational chords during parallel rotations with respect to the image plane). During sketching, one may approach the measurement point of the x-direction (with its vanishing point at F1 ) by bisecting the segment approximately between the principal point H and the vanishing point of the y-direction (F2 ). ⊕

Fig. A.24 Roman aqueduct and a variation by Zorica Nikolic Aigner

Fig. A.25 Catenaries everywhere

We are now at a point where we can draw images such as the one in Fig. A.24 on the right, though we should not be afraid of curved lines. The elliptic images of the circular arcs are well determined by their vertical starting tangents and the horizontal tangent at the highest point, which passes through a principal vanishing point in the image.

A.4 Perspective sketching

629

When sketching curves, one should take care to draw the tangents at endpoints as well as the tangents of special points (such as the highest, lowest, left-most and right-most point) first. In case that shadows have to be added to the perspective image, it is always an advantage to follow the directions that lead to the principal vanishing points. This strengthens the “vanishing-point appearance”, which is so crucial for our spatial understanding. The “suspension bridge” in Fig. A.25 was produced in the same way. For illustrative purposes, the tangents at the points P and Q of the catenary and its intersections T are inscribed exactly below the lowest point.

Scaffolding Capturing of curved lines by means of points and tangents (line elements) is an important and legitimate part of sketching. Whenever we wish to depict complicated objects, it is always advisable to imagine a sort of scaffolding that captures the locations of important points of the object.

Fig. A.26 On the left: An almost undistorted bicycle (frontal perspective). Center: the most common view from the front. On the right: strongly distorted (being photographed by a lens with very short focal length).

Fig. A.27 Freehand drawing of bicycles

Let us consider a bicycle (Fig. A.26), which (to be honest) is not even that complicated, since it essentially “lies in a single plane.” If the bicycle pole

630

A course in freehand drawing

is imagined to be horizontal, then its end points, along with the midpoints of the wheels, form an almost equilateral trapezoid. The pedals are located roughly halfway between the hubs. This is already a good starting point, and once it is sketched, the “rest” appears almost by itself. Fig. A.27 shows two bicycle variants by Stefan Wirnsperger and Otmar Öhlinger. The following must be considered when drawing the wheels:

Fig. A.28 Interior views of a tunnel

Rules for the depiction of circles in a perspective image: • The image of a circle is an ellipse (in general, and sometimes also part of a hyperbola), and thus, it possesses two symmetry axes. The center of the circle is not seen at the center of the image curve (ellipse or hyperbola). • One should, if possible, sketch the images of the foremost and backmost points of the circle, including their perpendicular tangents, as well as the highest and lowest points. The images of the corresponding horizontal tangents pass through the vanishing point of the horizontal diameter. Fig. A.28 is meant to illustrate that images of circles may very well be parts of hyperbolas. When viewing a torus-shaped tunnel (see also Fig. 6.77), one is, in fact, located within the right circular road edge, viewing the scene such that nearly all visible circles become parts of hyperbolas. If the tunnel exhibits a high curvature, then the inner edge of the road may be an ellipse. This happens whenever the plane which is perpendicular to the viewing direction through the eye point (vanishing plane) does not intersect the circle. ▸▸▸ A helical staircase in a perspective view Hieronymus Rodler published a book about perspective drawing in 1531 (five years after Albrecht Dürer). His explanations sometimes lacked a geometrical background. The drawing in Fig. A.29 is based on Rodler’s detailed instructions for drawing helical staircases.

A.4 Perspective sketching

631

There are crucial differences between the correct perspective on the left and the drawing on the right. As an exercise, the reader is invited to find the main differences between the two drawings. One might also compare them to the fisheye photograph below.

Studies of a helical staircase. Top right: a perspective drawing by Hieronymus Rodler , on the left: a “modern alternative” by Christian Perrelli. Bottom right: This fisheye photograph seems to bear some resemblance to Rodler’s drawing. However, there are crucial differences. Most importantly, there are hardly any straight lines in the fisheye photograph (except where the straight lines intersects the optical axis).

Fig. A.29

◂◂◂

632

A course in freehand drawing

Shadows in perspective images Shadow constructions of central views are no more complicated than those of normal views. However, let us remind ourselves that the novice should not attempt to draw shadows of complex scenes. Again, these words of caution are due to the noticeable and distracting nature of incorrectly drawn shadows – especially as they go against the primary goal of perspective sketching: visual descriptiveness. The following theorem is of fundamental importance: The perspective image of a light ray through any given point passes through the sun point, and its top view passes through the sun foot point.

Fig. A.30 Front lighting on the left, back lighting on the right

Let us differentiate between front lighting, back lighting, and side lighting (the limiting case). The situation of front lighting is the easiest to understand (Fig. A.30 on the left): The Sun S is depicted as a point above the horizon. In cases of a horizontal viewing axis, the image of its foot point S ′ lies exactly below S on the horizon h. We may derive the shadow Ps of a point P by intersecting P S with P ′ S ′ . In the image, it also follows that Psc = P c S c ∩ P ′c S ′c . In the drawing, we may omit the symbol for the central projection (the c ) as long as we are able to distinguish – at least in the mind – between the spatial situation and the perspective image. Now let us take a look at the back lighting situation (Fig. A.30 on the right): Nothing seems to change from the perspective of construction, if we accept that the sun point, as a theoretical point, may also be below the horizon, without the scene being set at night. We can, in fact, get the image of the Sun by connecting the Sun to the eye point (this would be a ray of sunlight

633

A.4 Perspective sketching

Fig. A.31 Simple scene with shadows

that would hit the back of our head) and intersecting the connecting straight line with the image plane (which is always vertical and in front of us).

Fig. A.32 Side lighting: easier to construct and visually appealing

⊕ Remark : In the practice of sketching, the Sun’s mid- and foot points are usually far outside the range of the drawing sheet. This is no problem for freehand artists: As long as we know the approximate position of these points, we may still inscribe the important respective sections of the connecting straight lines. ⊕

Reflections Only very small sleights of hand are needed in order to enrich our perspective images with simple reflections. Let us restrict our attention to horizontal and vertical reflection planes (water and the classic example of the mirror on the wall). We would do well to remember the following rule: Each mirror produces a virtual counterworld, which can be observed through the mirror window.

634

A course in freehand drawing

Fig. A.33 Simple scene with side lighting

There exists an “opposite point” P ∗ for each point P , which, by the rules of reflection, is located on the normal of the mirror plane. The distances of both points from the mirror plane are equal. The reflection in water is especially easy to draw (Fig. A.34): We simply have to find the top view P ′ in the water plane of a point P . The segment P ′ P may now be inscribed downwards. If the viewing axis is horizontal, then we may immediately recognize this “doubling” in the image.

Fig. A.34 The reflection in a water surface is easily drawn.

Fig. A.35 Perpendicular mirrors: the circumscribed cuboid is the secret to our success.

The reflection in a perpendicular wall (Fig. A.35) is no more difficult than in a horizontal surface. The path s of the reflection plane and the direction of the reflection normal (vanishing point S) must be known. Let P be, once again, a point with a top view of P ′ . Let us project the segment P P ′ in the direction of the reflection normal. This gives the points 1 and 2 in the mirror plane (1 at the intersection with the path s and 2 above it). Above

A.4 Perspective sketching

635

the midpoint 3 of the segment 12 (whose half is also visible in the image), we can find the top view of the reflected point. The reflection point P ∗ is located directly above it. Let us keep 1 → 2 → 3 in mind.

Three principal vanishing points

So far, we have only considered perspective images with a horizontal viewing axis. Let us now deal with the general case.

Fig. A.36 Three principal vanishing points

The three coordinate directions vanish in the image through the principal vanishing points F1 , F2 , and F3 . The horizon h = F1 F2 , if viewed from above or below, tilts in the direction of the upper or lower edge of the page. Perpendicular straight lines no longer appear to be parallel. A cuboid can quickly be sketched (Fig. A.36), but what about its shadow on the base plane? Now we have to adapt the previously defined rules, and never forget that the Sun and its top view are also connected by a vertical, so that: In a general perspective, the sun point S and the sun foot S ′ lie on a straight line through the vanishing point F3 of all vertical lines. We may again distinguish between back lighting (Fig. A.36) and front lighting (Fig. A.30) depending on whether or not the sun point lies above or below the horizon. The special case of side lighting does not seem to bring as many

636

A course in freehand drawing

advantages as with a horizontal viewing axis, because now the light rays only appear parallel in the top view (according to our rule, the sun point lies on a horizontal through F3 ).

Fig. A.37 Front lighting: Different styles, with the same theory behind them.

Fig. A.37 shows a sketch and the “finished” general perspective image (Stefan Wirnsperger), both of which show correct cast shadows. The perspective image on the right shows no construction lines. The sketch clearly shows that it is necessary to think things through very carefully.

Fig. A.38 Always pack sophisticated objects into cuboids, and give a suggestion of shadows!

Fig. A.38 shows other perspective images with three principal points. In such sophisticated drawings, trying to draw an accurate rendering of cast shadows would be too risky: So, only add a subtle suggestion of shading. Nevertheless, it is always useful to pack more complicated objects into minimal bounding boxes,since dealing with cuboids is what we know best.

B

Geometry and photography

As we have already seen, geometry is not just a theoretical mental game that can be played by a select few. Its applications are manifold, and one of the disciplines most obviously connected to geometry is photography. Photographs represent the “classical” perspective. Our knowledge about perspective helps us to create certain effects deliberately. For those readers who have only skimmed the theoretical content of this book, some of the geometrical statements outlined in the previous chapters will be repeated. Conversely, many readers may already be familiar with some of the topics and techniques that will be discussed in this chapter. It might still be useful to illuminate these matters from a geometrical standpoint, if only to clarify the following questions: How can we employ simple tricks to produce images which could otherwise only be taken with the use of expensive shift lenses? Why is the choice of the focal length not only a question of “view”, but also matters with regard to where the photograph is going to be used? When are ultra-perspectives not only permitted but actually necessary? Why does the depth of field depend on the focal ratio? What changes in underwater photography? Photographs illustrating these questions can be found throughout this book and are not merely limited to this appendix. This reinforces the interconnection between subjects that only appear to separate at first. Anyone who wishes to approach geometry with the help of photography (and vice versa) is most welcome to do so! © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3

637

638

B Geometry and photography

B.1 Focal lengths and viewing angles

Fig. B.1 The famous Piazza San Marco in Venice: 17-mm focal length, full frame sensor. The image seems to be unnaturally distorted. However, we will see later that this may, under some circumstances, be necessary.

Fig. B.2 Left: the same subject, but shot with 400mm focal length. The focal length requires you to move further away. The effect is completely different than in the first image. Right: the same subject, shot with a 15-mm fisheye and a full-frame sensor.

Today’s lenses (zoom-lenses in most cases) are extremely complicated. Before the advent of digital photography, by far the most popular types of negatives were 24mm × 36mm in size. The lenses of non-digital reflex cameras usually had focal lengths in the approximate range of 20–400 mm (with some expensive exceptions).

B.1 Focal lengths and viewing angles

639

Modern digital cameras very often have a sensor that is much smaller than 24mm × 36 mm, and the range of the focal length is accordingly smaller. (The only exception are some professional “full frame cameras.”)

Focal lengths and the viewing angle are connected The physical term focal length used to be (and still is, given certain conditions) a measure for the geometrical term angle of view – the angle between the lines of sight from the lens center through the endpoints of the image diagonal. The smaller the focal length, the greater this angle is (Fig. B.3). If the angle is greater than 50○ (which in full-frame cameras corresponds to a focal length of about 35 mm), then one is usually faced with a wide-angle lens. Lenses with angles above 85○ (focal length of about 24 mm) are already counted among the super-wide-angle or ultra-wide-angle lenses, and those with angles above 180○ (yes, this is possible!) are usually called fisheye lenses (below 14–16 mm). If, on the other hand, the image angle is smaller than 20○ (about 85 mm), then one is dealing with a so-called telescopic lens.

Fig. B.3 Different viewing angles ϕ (measured in degrees) correspond to different focal lengths f (measured in millimeters). The formulas in this chapter interpolate data given by various camera producers. The general rule is the following: the smaller the focus, the larger the viewing angle.

⊕ Remark : The focal length is now widely considered to be a confusing measure for the image angle. Non-full-frame digital cameras based on the reflex camera principle often have a “crop factor” between 1.5 and 1.6 (sometimes even 2). If a zoom lens is labeled with 18-200mm, then on a full-frame camera, this corresponds to 18×1.5-200×1.5mm = 27-300mm. This is due to the smaller size of the CCD (the light-sensitive layer or chip). However, exceptions confirm the rule: Some expensive reflex cameras do not crop at all (full-format sensor), while some have a crop factor of 2. In digital cameras which are not reflex cameras (and are, thus, incompatible with the “good old” lenses), one may usually find focal lengths that correspond to about one fourth of the values of full-frame cameras. One might, nevertheless, produce

640

B Geometry and photography

comparable image angles. Here, the size of the CCD appears to be significantly smaller (at the cost of image quality). ⊕

One might be tempted to conclude that lenses with different focal lengths or different image angles produce different images. From the perspective of geometry, however, the following important theorem holds: The chosen perspective depends only on the position of the lens center and on the direction of the optical axis (inclination of the camera), and not on the chosen focal length. A telescopic-lens photo is merely a “enlargement” of the image center.

▸▸▸ Entire lens systems work like one single converging lens An objective lens consists of several lenses and lens groups (Fig. B.4). If we attempt to analyze the direction of light in such a lens, we have to admit that the matter does not seem to be as trivial as it first appears. First, we can determine that rays which enter into the lens system in parallel are eventually focused on the light-sensitive layer (assuming that the distance is set to ∞.) If we translate the direction to the point P far in the distance through the image point P c , then it has to pass through a fixed point E on the optical axis – if this were not the case, then we would not be dealing with a central projection. So, let us have confidence in the lens manufacturer’s ability to synchronize their 10 to 15 lenses in precisely such a way.

Fig. B.4 The complicated light path through a modern lens. Still, the whole lens system works like one single lens with the optical center E (corresponding to the eye point of the perspective).

⊕ Remark : The question of why lens manufacturers go to such elaborate lengths is easily answered: It serves to correct the many divergences from the perfect image. It starts with the simple physical fact that different spectral colors are refracted in a different way. A simple lens, thus, produces “rainbow edges”. ⊕ ◂◂◂

When, for a certain distance setting, P does not lie very far away, the light rays that are emitted by P and enter the lens system will not converge at exactly the same point on the photo layer. The point will thus appear as a blurred spot on the image. If P is an important point, the distance between

B.1 Focal lengths and viewing angles

641

the frontmost and the backmost lens block should be altered so that a single image point P c on the photo layer is created. ⊕ Remark : This modification of the distance setting will cause the eye point of the perspective – given a fixed camera body – to shift. This is an important aspect to consider when you wish, for instance, to take a series of photographs of an object with a fixed camera at varying distance settings in order to produce an “infinitely sharp image” with the appropriate software. ⊕

642

B Geometry and photography

B.2 3D images in photography? Are photographs central projections? Photography is a source of fascination for many people – especially for mathematicians and geometry enthusiasts. In geometry classes, we sometimes say, in simplified terms: Photographs correspond to central projections (perspectives) of space. This means a reduction of three-dimensional space into the two-dimensional plane. This can be “proved” by the fact that it is possible to reconstruct the photographed three-dimensional scene quite accurately from a number of photographs. It is quintessential to use high-quality lens systems that reproduce straight edges as exactly straight. Even though this idea works quite well for scenes with larger technical objects, such as polyhedra (e.g. a furnished room or a building), it poses huge problems in the context of macro photography, that is, photographs of objects that measure just a few centimeters or even less than that. An impossible photograph

Fig. B.5 Left: impossibly sharp? Right: “normal macro sharpness”.

The flies in Fig. B.5, which measure about 1 cm, are fundamentally different in terms of the photographic techniques used to depict them. The picture of the fly on the left (with some disgorged digestive juice) is in sharp focus overall. An insect photographer would be puzzled: Even with the use of highly expensive equipment with the best macro objectives in existence, macro flashes and the highest aperture number possible (as in the picture on the right, where miniscule droplets of water can be seen on the complex eyes), it seems impossible to take such a photograph.

643

B.2 3D images in photography?

This poses two questions: Why can an object as small as a fly not be rendered in sharp focus overall, and how does it seem to be possible after all? This subchapter will explain the situation from a mathematical/geometrical point of view. The lens formula

Fig. B.6 Lens equation

In physics, the method of operation of a lens (or a well-aligned lens system) is explained as follows: Let P be a point in the real world. It emits (reflects) light rays in all directions. Two of them will have easily predictable properties. The principal ray through the lens center C will not be refracted, while the ray parallel to the optical axis will go through the focal point F ∗ after the refraction. Behind the lens (the lens system), the two rays – and all others – meet in the pixel P ∗ . From Fig. B.6, using similar triangles, we can derive the lens formula: 1 1 1 = + . f d d∗

(1)

Here, f denotes the focal point, and d and d∗ denote the oriented distances of the point in space P and the pixel P ∗ from the symmetry plane through the lens center C, respectively. Using this method, we can determine the corresponding pixel for each point in space. The Gaussian collineation Let us define d = kf . Using the lens formula, we then get d∗ =

d k ⋅f = . k−1 k−1

(2)

644

B Geometry and photography

According to the intercept theorem, we get the following relation between the distances of a point in space P and its pixel P ∗ from the center C: CP ∗ =

1 ⋅ CP . k−1

(3)

Even though the mapping P ↦ P ∗ works in both directions, a camera will only be able to depict the half space whose points lie more distant from the lens than the focal distance f (k > 1): Points in the plane through the point F perpendicular to the optical axis are projected onto far points, because the denominator equals k − 1 in that case. It is easy to show that the mapping P ↦ P ∗ preserves straight lines: Let g be an arbitrary straight line in space. It can always be defined as the intersection of two special planes ε and ϕ, with ε being the connecting plane of g with the center C and ϕ being the plane through g that is parallel to the optical axis. ε is transformed into itself (ε∗ = ε) because we can think of the plane as a pencil of principal rays. The other plane, ϕ∗ , can be conceived of as rays parallel to the optical axis that transition into a pencil through the focal point F ∗ and the intersection line of ϕ with the symmetry plane. The image g ∗ of g is the intersection of ε∗ and ϕ∗ and therefore a straight line. Our mapping P ↦ P ∗ is thus a collineation – which is the technical term for images that preserve straight lines.1 This insight goes back to C.F. Gauss. How does this relate to photography? Using the simple formula (3), we can very easily transform spatial objects made of a number of points into equally spatial objects. How does this relate to photography, which, after all, produces a two-dimensional result? Let us consider a point P at a distance d from the symmetry plane (collineation plane). If the plane π of the sensor of our camera happens to be located at a distance d∗ from the collineation plane, the pixel P ∗ will lie in π. Thus, the intersection of the object that we aim to reproduce with the “plane of sharpness” through P at a distance d parallel to the collineation plane is rendered sharply.2 All other points are rendered more or less sharply. The extent of blurring is dependent on a number of different parameters, as we shall see. One crucial parameter is the distance of the photographed object proportionally to the focal length.

1A

note for insiders: This mapping is a very special form of perspective collineation, because the center lies in the collineation plane (the symmetry plane). Such a collineation is called elation. 2 Using our common sense, we may have assumed that in a photographic image, we can render sharply all those points that have a certain constant distance from the lens center (thus lying on a sphere around C), which depends on the distance d∗ from the sensor plane. However, according to the lens formula, this is not the case, as all of those points lie in a plane, the plane of sharpness at a distance d.

B.2 3D images in photography?

645

Photographing elephants vs. flies Let us first consider the image of a “large” object from a great distance. (What is meant here is the relation of the object size to the focal length f (Fig. B.7).)

Fig. B.7 Elephant photography (depicting large objects from a great distance): The corresponding virtual 3D image is “almost flat”, i.e., all image points are close to the sensor plane. The image in the sensor plane is more or less “sharp”.

For points at a great distance d = k ⋅ f (k >> 1), the image distance d/(k − 1) (formula 2) does not vary a great deal. The collinear virtual object behind the lens will thus be strongly oblate, which means that there will be minor blurring of those points that do not lie precisely in the plane of sharpness. Taking a sharp full-size photograph of an elephant thus poses no problem. The smaller the object that we want to photograph is, and the closer this object is to the “forbidden” vanishing plane (Fig. B.8), the more the expression f /(f − d) = 1/(1 − k) in the transformation formula (3) will vary. This means that the points will become blurrier, which becomes a genuine problem. A brief remark: Short focal lengths f apparently have a positive effect on the focus depth, as a fly or a snail becomes larger in proportion to f . Cameras with small sensors have a correspondingly shorter focal length.3 3 In

technical specifications, the focal length (e.g., 100mm) of a lens is often provided in terms of a 35mm equivalent, which means that, for a “full frame sensor size” of 24mm×36mm, the lens has a focal length of 100mm. However, if the sensor only has a size of, for example, 6mm×9mm, the same visual impression can be achieved with a focal length of just 25mm. In this special case, we have a crop factor of 4. Nowadays, it is possible to take amazingly sharp macro photographs with good smart phones, owing to their extremely short focal lengths and correspondingly tiny sensors (with much larger crop factors). However, this leads to the problem of having a large number of pixels in the tightest of spaces, which inevitably leads to a loss of quality.

646

B Geometry and photography

Fig. B.8 Macro photography: When a small object close to the lens is photographed, the 3D distortion of the corresponding virtual image is considerable. Only points in the focal plane π will, therefore, be depicted in sharp focus.

Geometry vs. physics In geometry, the matter seems to be trivial: Let us intersect the light ray through the lens center with the sensor plane. Seen from the perspective of physics, this, of course, does not work: A single light ray is not sufficient to expose the sensor. We will thus have to install a circle-shaped opening in the collineation plane – the aperture. All light rays emanating from a point P in space will then lie inside a skewed circular cone through the opening, which is itself refracted in a skewed circular cone (Fig. B.8). Real halfspace Virtual halfspace P C

CoC

P∗

collineation plane

Plane of sharpness

sensor plane

Fig. B.9 The Circle of Confusion (CoC) in the sensor plane p can be interpreted as the intersection of an oblique cone passing through the circular aperture opening c.

The entirety of light rays in this refracted skewed circular cone exposes the sensor plane in a dot-shaped way only if P lies on the plane of sharpness. In all other cases, there is a so-called circle of confusion on the sensor (CoC for short). We could now assume that we only need sufficient light (flash) in order to keep the aperture as small as possible. (We speak of a high aperture number in such cases.) However, this is only possible up to a certain limit. (The aperture should be bigger than 1 mm at any rate.) If we reduce the size further, the wave properties of light further complicate the matter: It leads

B.2 3D images in photography?

647

to diffraction on the edges of the aperture, which results in inconvenient diffraction blurring. Optimal results can be obtained by using the optimum aperture indicated by the manufacturer of the lens. Photographers know that exceeding the optimum aperture will reduce the image quality. Focus stacking In the picture of the elephant, we hardly ran into any problems – if a photographer targets a point that lies approximately at the end of the first third of the desired distance range, the picture will be sufficiently sharp.4 In macro photography, however, a lack of sharpness is a serious problem – especially if we are not dealing with artistic but scientific images.

Fig. B.10 Two mating dragon flies, photographed several times with varying lens centers (and focal points). The first and the last photo of the series can be seen on the left. The focus-stacked image on the right can be considered sharp in the zone that is defined by the two animals. The background still remains blurred, which is, aesthetically speaking, a big advantage. Thus, focus stacking can also be considered as an artistic tool.

Nowadays, a technique called focus stacking has been established. In essence, it works in the following way: The camera takes a number of images of a scene in the shortest interval possible, varying the distance of the plane of sharpness. By using this method, we get an image series where different layers of the object are in focus one after the other. The theory of image processing is quite advanced by now, and software used for this purpose is able to distinguish sharp from blurry pixels. In a second step, one sharp image is created from this entire image series. How well this works even without a tripod is shown in Fig. B.10: On the left, 4 Artistic

photographers often encounter the opposite problem: They deliberately want to work with blurred areas. In such cases, using larger focal lengths and a wide-open aperture is recommendable.

648

B Geometry and photography

we see the first and the last picture of such a series by way of example; on the right, we see the final product.5 The plane of sharpness scans the object For any position of the sensor plane (distance d∗ ), there is, thus, exactly one plane of sharpness (distance d) in the Gaussian collineation. Its position follows from the lens formula (1): d = f d∗ /(d∗ − f ).

(4)

In commercially available cameras, the position of the sensor plane is fixed, and the position of the lens center C moves forward and backward on the optical axis. If we focus on points that are very far away, C lies in front of the sensor plane at a distance f (with d∗ = f , or equivalently d = ∞). If we photograph a two-dimensional shape – such as a drawing – that lies in a plane parallel to the sensor plane at a distance of s = d + d∗ and if we focus it, the center C will have a position at a distance d∗ from the sensor plane that we want to calculate. With the formula (4), the following applies: 2

2

s = d∗ /(d∗ − f ) or d∗ − sd∗ + sf = 0

(5)

The ambiguous solution of this quadratic equation is √ s s2 ∗ d = ± − sf . 2 4 In order for the expression below the root not to be negative, s ≥ 4f must apply. This is, indeed, always the case because of the requirement d > f . (If d = d∗ = 2f , the solutions coincide.) Furthermore, both solutions are always valid, even though one would – for practical reasons – tend to stick to one algebraic sign when computing a series of camera positions. If the lens system lies within the computed distance d∗ in front of the fixed sensor plane π, our two-dimensional shape will firstly be rendered in overall sharp focus on the sensor, and secondly, it will appear similar, and thus perspectively undistorted, even though it will not retain its original size. Let us now turn back to three-dimensional objects. If we make a series of photographs while purposefully varying the distance of the lens center, we will get photographs in which one section line of the object is rendered sharply and largely undistorted (it is merely scaled). Fig. B.11 illustrates this matter: In a simulation of this process, a cube was mapped by means of layers, which 5 An

additional advantage of this method is the fact that we usually do not get an “infinitely” sharp image, but that there is a certain layer rendered in sharp focus. Blurry backgrounds facilitate the isolation of objects from the background and prevent the viewer’s gaze from getting distracted by unnecessary details.

649

B.2 3D images in photography?

Fig. B.11 When the center C of the lens system (and therefore also the focal point F ) moves along the optical axis (with fixed sensor plane π), the plane of sharpness which corresponds to the sensor plane moves in parallel. Its intersection lines with the spatial object are depicted in sharp focus, but in an absolute size that depends on the distance Cp.

can be triangles, quadrangles, pentagons, or hexagons. However, if we now simply put these pictures on top of one another, we will end up with strangely distorted perspectives (see also Fig. B.12 on the left). Straight lines – such as the edges of the cube – are depicted as curved (it is possible to show that they form parabolas.) The reason for this is, of course, that, owing to the different distance of the lens center from the sensor plane, the section lines are scaled proportionately to this distance. Converting the scanning process into normal/central projections Strictly speaking, we scanned our object in the way outlined above, though we must bear in mind that only those section lines were recorded that were visible from the respective center. Let us now conduct some skilful scaling in order to compute the relations in the visible three-dimensional real space during the scanning process. Let t be a line segment in the plane of sharpness, and thus in space, and t∗ is the line segment parallel to it in the sensor plane π. According to the intercept theorem, the following applies: t ∶ d = t∗ ∶ d∗ . With the scaling factor λ = d/d∗ ,

(6)

we can thus calculate the genuine length t from the image length. If we scale all pictures of the series, with the factor changing from one picture to another, we get a normal projection of the object (see Fig. B.12, center). This is remarkable insofar as it is impossible to achieve a normal projection

650

B Geometry and photography

with a single photograph, except if we used an astronomical telescope with an almost infinite focal length.6

Fig. B.12 A spatial object (in this case a red cube) is “scanned” by a “sweeping focal plane”. Only the intersections with the plane are depicted in the sensor plane. If the corresponding images of the section are not scaled, the result is neither a central nor a normal projection (image on the left). Scaled with the factor λ in Equation 6, the image is a normal projection (middle image); scaled with the factor µ in Equation 7 as in the image to the right, the result is a perfect central projection (= “perspective”). In the latter case, the center of the perspective can vary almost arbitrarily.

In order to achieve an exact central projection (perspective), which exclusively relies on unambiguously recorded points, we will choose a position as the center where the lens center used to be when the last still visible points of the object to be depicted appeared sharp (d = dm maximal ⇒ d∗ = d∗m minimal). The ith picture will then not only be scaled according to the formula (6), with the factor λi = di /d∗i , but additionally with the factor d∗m /dm : µ=

di d∗m ⋅ d∗i dm

(7)

If we now feed the image series into a software designed to recognize sharp pixels, we will get a picture of graphical precision that is sharp and perspectively correct, as can be seen in Fig. B.14. The square stamp in Fig. B.13 passes the relatively strict geometrical tests that can be used in order to test the correctness of a perspective, and the same is true of the “geometric still life” in Fig. B.14. This is important because we do not usually photograph miniature geometrical figures in practice, but rather living beings and natural objects like in Fig. B.15. Creating a full-size sharp photograph of the stamp would be a classic task of macro photography, while the still life is already a medium-sized scene and thus easier to photograph in overall sharp focus.

6 However,

there is, one limitation: Even from various positions on the optical axis, we cannot always see as much of a surface as we would in a genuine normal projection. Just think, for example, of a spaceship directly approaching the moon. From its position, we will never be able to see 50% of the moon’s surface, the way we do from Earth.

B.2 3D images in photography?

Fig. B.13 A square stamp of typical macro size is focus-stacked. With the application of the corresponding scalings of the images, the result is a geometrically perfect perspective.

651

Fig. B.14 A typical geometric scene (cube, square, cylinder of revolution). From the geometric point of view, the stacked image fulfills all requirements of a single central projection.

Fig. B.15 Stacked photograph of a male mayfly (genus Cloeon) with its so-called “turban eyes”. A turban eye is an additional part of the compound eye, whose large ommatidia are all directed upwards. With them, the males can detect females flying above them in the air during the mating dance.

652

B Geometry and photography

Outlook Speaking from a mathematical/geometrical point of view, it is important to note that much more can be done with a series of pictures of an object, owing to the fact that these pictures provide information of the object’s location in space – one example being 3D models. In any case, focus stacking on the macro level should make it possible to achieve results that would rival those of laser scanners if the pictures were done under laboratory conditions – though the technology behind it is simpler, quicker, and cheaper.

Fig. B.16 To the left, only three photos were stacked, which allowed for major parts of the praying mantis to appear sharp. The blurred background of the stacked photo is deliberate. To the right eight pictures were stacked (10 mm large fruit of a burdock).

If the objects that we want to photograph happen to be small animals, we are faced with the additional problem that these seldom tend to freeze in place, and they usually move at least their feelers or individual limbs (Fig. B.16, left.) In such cases, the image series should be processed in no more than a tenth of a second, which will probably be possible in a few years time, if we bear in mind the rapid technological advancement in recent years. Currently, commercially available cameras still need a full half second for a complete series of 8 to 10 pictures – the bottleneck does not occur when the pictures are saved but is a result of the continuous re-adjustment of the focus. From an aesthetic point of view, we often only need two or three pictures of an insect for impressive photographs. In Fig. B.16, it was important to focus on the mandibles and eyes of the praying mantis – it is secondary that the rest of its body appears blurred.

653

B.3 Stereoscopy

B.3 Stereoscopy Optical illusions with one eye closed We already know the following from Chapter 2: When we look at what seems to be a cuboid (colored yellow in Fig. 1.16; points P , . . . ) with one eye closed, the cuboid may actually turn out to be some other form of polyhedron (colored red in the image), which is somehow related to the cuboid (Fig. B.17): For this optical illusion to work, the polygons formed by the vertices P ∗ , . . . of the “placeholder polyhedron” (that is, the polyhedron that we would see with both eyes open) should also be flat, because, even with one eye closed, non-flat surfaces are easily recognized by the different shading effects. Among the infinitely many forms that the placeholder polyhedron might take, polyhedra with perspective collinear distortion are particularly suitable. The following statements apply to these polyhedra: Corresponding points (e.g., vertices) lie on viewing rays (projection rays) through the optical center C, and planes (e.g., the carrier planes of side surfaces) correspond to planes ("plane preserving").

C

P∗ P

Fig. B.17

π

Polyhedra with identical images

Binocular vision If we look at the same cuboid with both eyes L and R (Fig. B.17), we are less likely to be deceived by a collinearly distorted polyhedron. Yet, we will see that, even with both eyes open, optical illusions are still possible due to the brain’s capacity for visual imagination, which often make us “see what we we want to see”. Since the depth (measured as the distance from the vanishing plane through the two eye points perpendicular to the main viewing direction) varies, the viewing angles for the individual points differ by a lesser or greater degree. When we take two photographs with parallel optical axes,

654

B Geometry and photography

PL PR

P

R L

Fig. B.18

Parallaxes during binocular vision

we refer to these viewing angles as parallaxes: The difference between the right image PR and the left image PL increases as the depths of the points decrease. PL and PR lie on a line that is parallel to the axis connecting the two eyes (Fig. B.18). When we alternately close our left and right eye, the parallax distance of the thumb on the outstretched hand creates the effect that is used in the so-called “jumping thumb method”, where the thumb appears to jump in relation to the seemingly fixed, distant background. Since the length of the arm is to some extent proportional to the pupillary distance, the jumping thumb method can be used as a measuring unit to estimate the distance of an object or the size of objects when their distance is known. (As a rule of thumb: The distance of an object is about ten times as large as the zone width that is measured for this object with the jumping thumb method.) There are no parallaxes in the starry sky, which is why we cannot directly determine the distance of stars with optical means. However, by using the diameter of the Earth’s orbit (300 million km), we can obtain images with measurable parallaxes at least for relatively close stars in a half-year interval.

Stereoscopic vision We speak of “stereoscopic vision” when we simultaneously look at two slightly different flat perspectives (such as two photographs) that are arranged in such a way that the intersection of the viewing rays (projection rays) creates the illusion of a three-dimensional scene. For instance, if the two images of the cuboid in Fig. B.18 are projected onto a screen in such a way that distance

B.3 Stereoscopy

655

between the intersection points of the two camera axes and the screen equals the average human pupillary distance of 60-65 mm, and if the position of our two eyes coincides with the lens centers that are virtually generated by the magnification of the stereoscopic image’s center, then we get the same spatial situation as in photography and our brain is capable of combining the two images to an illusion of the original spatial object. The illusion can be improved with tricks ensuring that the left eye only sees the image produced by the left camera and the right eye only sees the right image. (In the past, this was achieved by anaglyph glasses with red and green lenses; nowadays, polarization glasses or shutter glasses are used.)

The brain readjusts images with collinear distortions The correct creation and positioning of the two images is crucial: Only if both images are calibrated and adjusted to the respective viewer, we can expect our brain to recreate an exact illusion of the spatial situation. In most cases, the cuboid will not appear as an exact cuboid, although most viewers may still identify it as such.

Through “cross-viewing” (also known as the cross-eyed method) and by additionally varying the distance (zooming) if necessary, most people are able to see a three-dimensional object. Fig. B.19

Fig. B.19 is meant to be a test image for our readers. Depending on the size of the stereoscopic pair of images, we can use the so-called “cross-view” to see the spatial object in the middle “grow out” of the image plane. The flower was photographed twice from a close distance. The optical axes of the two images are parallel and less than 1 cm apart. (This distance is enlarged when we print the images or project them onto a screen!) If a test subject manages to create a better spatial illusion by enlarging or reducing the stereoscopic images – for instance, on a computer screen or by means of a projector – then this is due to the fact that the axis distance has been adjusted to the pupillary distance. By turning the head slightly (and moving the pupillary axis parallel to the screen or printed images), the proportions of the threedimensional image can change slightly without disturbing the spatial illusion.

656

B Geometry and photography

Now we would like to show that what we see are generally spatial collineations of the original object. Let us start with the simplest case: As in Fig. B.18, we project in such a way that the distance between the intersection points of the camera axes (in a stereoscopic image like the flower in Fig. B.19, these would be the centers, or rather the diagonal’s intersections points, of the original photographs) equals the average pupillary distance of human eyes (±65 mm for men, ±62 mm for women). With this scaling, the position of the two eyes is precisely determined to correspond to the lens centers of the two cameras. But what happens if we move our eyes along the camera axes?

PRPL

PL

yellow: original object blue: collinearly distorted object

right image: cross-section new eye points L∗ , R∗ closer to the projection screen

PR

P∗ P

P∗

P

R∗ R L∗

R∗

R

L∗

L

L

pupillary distance = distance between the two image centers

When – with the correct adjustments for pupillary distance – viewing subjects change their distance to the stereoscopic image, the object is only stretched or compressed. Fig. B.20

Fig. B.20 shows (theorem of intersecting lines/intercept theorem!) that the changes to the stereoscopic image’s spatial result are relatively minor: The original object is only stretched or compressed (orthogonal affine distortion). This special collineation preserves parallels and division ratios. The latter do not even change when the viewing subject moves around the room (while maintaining a parallel pupillary axis). The distortion is mitigated by the fact that, for instance, when the viewing subject sees a compressed image, they stand closer to the supposed spatial object, and this extreme perspective creates an even stronger illusion of depth.

A robust illusion If the pupillary distance does not coincide with the distance between the centres (the diagonal’s intersection points) of the two original images, then the reconstructed spatial object will still only be linearly distorted (perspectively collinear to the original). We can find that this is also the case when the left and the right image are moved closer towards each other. Fig. B.21 on the right demonstrates that, even in this general case, the viewing subject will

657

B.3 Stereoscopy

barely notice these distortions, because they are looking at the new object from a different perspective.

PR

yellow: original object blue: collinearly PL distorted object right image: perspective with the center P close to the new eyepoints L∗ , R∗ ∗ P L∗ R∗ R R∗ L∗

PR

PL P

P∗

L Neither the position nor the pupillary distance are properly adjusted here, but the blue object appears (almost) correct. Fig. B.21

The general case

We want to prove for the general case (as depicted in Fig. B.21) that representations of the original←→virtual object are always linear and thus preserve straight lines: Let g be a straight line in real space. Corresponding to g, there are two image straight lines gL or gR at the respective intersection of the image plane with the visual planes through L and R. Now we project from the two new points L∗ and R∗ , and from the resulting new visual planes, we get the intersecting straight line g ∗ . However, the axis L∗ R∗ must be parallel to the axis LR (which automatically implies that the two realigned images are at the same height). Otherwise, the new viewing rays would no longer intersect each other and the spatial illusion would collapse. The reconstruction from two perspectives proves to be rather easy. This also applies to non-classical perspectives, like, e.g., the fisheye perspective which is used in popular action cameras: Those cameras produce spatial fisheye perspectives/the spatial perspective of fish! This is much less noticeable in non-technical object that do not feature pronounced right angles (Fig. B.19).

To put everything into perspective. . . Not everyone is equally impressed by stereoscopic photographs and videos, regardless of the results that are presented above. Some people can see stereograms instantly and from any position, whereas others may require customized conditions and also, on occasion, complain about dizziness and headaches after some time.

658

B Geometry and photography

B.4 When should we use which focal length? A significant difference

Fig. B.22 Change of distance (constant principal ray)

After we have learned that the focal length or the image angle have no effect on perspective, it no longer seems to matter as much whether we take our pictures with a wide-angle or a telescopic lens. This approach is correct: A telescopic lens only helps us to exclude objects from the image which are not important to us and instead fill the frame with our primary photographic objective. If, on the other hand, the goal is to get “as much into the picture as possible”, it may be advisable to use a wide-angle lens. If we approach an object closely (small distance), then we need a big viewing angle (a wide-angle lens) in order to picture it completely. However, the object will then appear to be highly distorted, which may in some cases be the intention of the photographer. If, for instance, the viewing angle is 50○ , then this entails an “appropriate” distance (about twice the diameter of the object) and the use of a “normal lens” (with a focal length of about 50 to 60mm). The farther away we step from the object, the less noticeable the distortion becomes: The perspective moves ever closer to the principal point. We would now have to enlarge the image considerably (by using a telescopic lens) in order to picture the object at the same size. ⊕ Remark : In ultra-telescopic photographs (which are very common in nature photography – the gnu in the African savanna being just one example), the image comes close to a normal view. This has both advantages and disadvantages: The dramatic effect of a wide-angle photograph may be gone, but the distances are also shortened. One may get the false impression that the gnus and the gazelles – which, indeed, tend to graze together – are practically on the same spot (Fig. B.23 on the right). ⊕

B.4 When should we use which focal length?

659

Fig. B.23 An ultra-wide-angle photo (focal length of 17mm) can be seen on the left, where the trunk is already extremely close to the lens. A telescopic photo is pictured on the right for comparison (see also Fig. B.22), and a flattening of distances becomes noticeable.

Fig. B.24 Depth amplification with a wide-angle lens (28 mm) and depth shortening with a telescopic lens (670 mm). The boat is about 400 m away (this estimation is based on the diameter of the sun, which spans an image angle of about 0, 5○ [9]), but is certainly many kilometers away from the islands that are visible in the background.

Subjective changes in proportion The advantage is that the proportions of the animals in the picture are much closer to their “true proportions”. A gnu may have a back which slants downwards, but the true angle of inclination may best be seen in Fig. B.22 on the far right. Sometimes, it may also be an advantage to be a bit further away from the animals. The elephant in Fig. B.23 on the left must have mistaken the camera for food. The photo on the right was already done from a more respectful distance.

From one extreme to the other. . . Normal projection is an extreme case of a telescopic photo. In such images, the depth values – the distances from the observer – are no longer important (Fig. B.24).

. . . or: How a broom closet may be turned into a dining hall When taking photos of small rooms, one may no longer have the choice of an arbitrary focal length. The dilemma persists that while a wide-angle lens enables the photographer to encompass as large a portion of the room as possible, it gives the room a strange appearance (Fig. B.25 on the left): It

660

B Geometry and photography

Fig. B.25 Wide-angle lens vs. regular lens for interior photography

looks as though one were standing in a long and unnaturally stretched hall. This may be of interest for real estate agents who wish to sell a 10m2 -room for a steep price . . .

Unintended caricatures and passport photographs

Fig. B.26 Wide-angle vs. telescopic lens: Portraits should not be done with wide-angle lenses!

When taking pictures of human faces, the “magnification effect” of proportions inherent in wide-angle lenses becomes very striking (Fig. B.26). Thus, when we are asked to take a passport photograph, we should definitely employ a telescopic lens! Even though the heads of most people are not precisely spherical, the pictures in Fig. B.26 may give an indication of what could go wrong when we use a wide-angle lens . . .

Which focal length should we use underwater? When we take pictures of large underwater creatures, wide-angle lenses have to be employed in any case (Fig. B.27). Each meter of distance affects the visibility. At a distance of 10 or 20 meters from the camera, just about every color dissolves into gray and becomes drab, and not even the best flash gun can alter this fact! Stronger telescopic lenses are virtually never used underwater (Fig. B.27) – and for many good reasons. First of all, the refraction between water and

B.4 When should we use which focal length?

661

Fig. B.27 An extremely small focus of 14mm was used for this picture, and the adult dolphin almost touched the lens.

light (in the lens and the camera) already “lengthens” the focal length by about a third so that even wide-angle lenses quickly become “normal lenses”. Secondly, one is only capable of seeing a few meters ahead, even in crystal clear water – and finally, color fastness decreases rapidly with distance.

Fig. B.28 Flash guns can be counterproductive when plankton is present.

In Fig. B.28, a whale shark plows through plankton, which also causes the view to be highly limited. Flash guns are completely useless (and may, in fact, illuminate floating particles which would block the view). Fig. B.28 on the right: Remoras which accompany the whale shark can be captured from up close and appear in their true colors as they are illuminated by a flashlight. The solution for the “whale-shark problem”: Move as close as possible to the object you want to photograph and use an ultra-wide-angle lens (Fig. B.29).

662

B Geometry and photography

Fig. B.29 If the water is full of plankton, the only way to get good photos is to use ultra-wide-angle lenses (f = 14 mm, full frame sensor).

Nowadays, such “action cameras” (even with fisheye effects) are sold at comparatively affordable prices.

Depth is crucial Colors appear as they actually are only when the pictured object is very close to the observer, and only when we employ a flashlight or are close to the surface: A distance of only one meter in one meter depth is enough for the light to have to travel for two meters through water (one meter to the pictured object and another back to the observer) – which already causes parts of the red color components to be “swallowed”. Due to the fact that artificial light sources are not present in nature, red color tones may act as camouflage underwater.

Fig. B.30 The same turtle – on the surface and in 10 meters depth

B.4 When should we use which focal length?

663

Underwater and from a distance of more than two meters, flash guns are useless or even counterproductive (Fig. B.28). Thus, one has to rely on sunlight. Fig. B.30 on the left illustrates that more or less true colors can be expected close to the water surface when the distance of the photographer is not too large (1.5 meter). Fig. B.30 on the right shows the same turtle in 10 meters depth. Now, the sunlight has to travel 11.5 meters. Fig. B.31 on the left illustrates that in 20 meters depth, all red and orange colors act as camouflage and that a weak flash gun does not help either.

Fig. B.31 On the left: one meter distance to the stonefish, weak flash gun, picture taken during the day in 20 m depth (see also Fig. B.32). On the right: a flashlight from a close distance helps to detect creatures that would otherwise be nearly invisible.

Macro photography underwater Underwater macro photography may be difficult for a diver because one has to be able to remain very stable without the help of gravity. However, since one gets very close to the object and almost always uses flash lights or flash guns due to the lack of direct sunlight, the colors are almost true to life in the photograph (Fig. B.31 on the right, Fig. B.32).

Fig. B.32 The closer one gets to the predator (on the left a scorpionfish, on the right the same stonefish as in Fig. B.31), the more one begins to understand the effect of the camouflage.

Fig. B.33 illustrates that when we take pictures at night (or at greater depths), a flash gun is the only available light source. True-to-life colors are then easier to capture from less than half a meter distance.

664

B Geometry and photography

Fig. B.33 On the left: At night, the only light source is the flash gun. On the right: impressively camouflaged eyes of the crocodilefish (note the side view of the eye in the back).

Finally, Fig. B.34 shall illustrate that when we take pictures of really small objects, there is almost no difference to macro photography on land: We have a very shallow depth of field and should try to get as many points of interest into focus and/or use a high-focal ratio. Generally, one should always stop down strongly in this size range. (Illumination does not pose a problem due to the short distance – quite the contrary: Many automatic flashes tend to create overexposure at very short distances.)

Fig. B.34 A “genuine” close-up. It is important to note that the polyps on a hard coral need to lie on the focal plane due to their tiny size, even if one takes photographs with a closed aperture. A rush job is unlikely to produce a satisfactory result. The picture here reveals that there were other little animals crawling on the coral as well.

B.5 Primary and secondary projection

665

B.5 Primary and secondary projection

Fig. B.35 Primary perspective of a fairly harmless sand tiger shark taken with an ultra-wide-angle lens. Its snout almost touches the camera. When we look at the pictures as they are printed here, in such a small size and from a distance of 40–50 cm, they look unnatural. However, if we enlarge the photographs and force the spectator into a closer position in front of the diagonal intersection, we will manage to create a “natural” impression.

Ultra-wide-angle images are occasionally necessary! At first, the extreme wide-angle picture in Fig. B.35 may appear exaggerated – and it is, indeed, when we look at the printed image in this book from a distance of 50 cm or more. You are encouraged to try the following experiment: Shut one eye and position the other eye as close as possible above the center of the image (at a distance of about 10 to 15 cm but no closer than that because your eye could no longer focus at such close proximity). From this position, you will probably agree that the image no longer appears so distorted. This may be explained by the fact that it is, indeed, possible to move this close to an object in nature. From this proximity, it would no longer be possible to view the whole scene with a single image – you would have to move your head or at least your eyes in order to perceive other details of your surroundings. However, in relation to the very large object, the eyes remain in practically the same spot. Let us now go back to the significantly downscaled image: If you try to move your uncovered eye in its extreme position, close above the image center, its motion would be equivalent to the described head motion – and because

666

B Geometry and photography

the other eye is covered, you would not be able to assess distances anyway. We have thus managed to scale down the same situation that actually happened in three-dimensional space. Let us call the spatial situation primary perspective and the image situation the secondary perspective. When we accept these assumptions, the following rather obscure theorem holds true: In order to get a realistic impression of a photograph, primary and secondary perspectives should coincide. In other words: While taking the picture, the photographer would already have to ponder whether the person looking at the photograph would be able to assume the camera’s original position. Fig. B.38 on the right may – in some circumstances – be a necessary method of depiction: Imagine a representation of trees exhibited in museum through which visitors are allowed to walk. There is one massive tree on a high wall that is supposed to be pictured such that a visitor passing by in close vicinity to it may experience the illusion that they can look up at the tree’s canopy. For this purpose, the trunk of the tree in the lower part of the image must be thick enough to produce a realistic spatial effect!

Cinema screens and portable TVs The issue of corresponding perspectives is, in my opinion, important enough to warrant another example: An underwater photographer takes pictures of reef sharks or of another, less dangerous species, such as the sand tiger shark in Fig. B.35 (the primary perspective in Fig. B.36 left). Although sharks are usually smaller than a human being, they appear highly distorted when they move closer to inspect the ultra-wide-angle lens.

Fig. B.36 On the left: Primary perspective – the camera is close to the reef shark’s snout. Center: A dramatic, but geometrically correct secondary perspective – people sitting in the first row will actually get a pretty realistic impression of the situation! On the right: The image angles no longer correspond to the primary situation if the picture is seen from further back.

The images captured by the photographers are a sensational success, and the film is screened in cinemas (Fig. B.36 center and right). Viewers in the front rows are forced into a secondary perspective that closely resembles the primary perspective. After some time, the film is also broadcast on television. We first get a small picture in a printed TV guide (Fig. B.37 on the left), which stimulates our

B.5 Primary and secondary projection

667

Fig. B.37 Unrealistic secondary perspectives: On the left, the photo of the reef shark looks strangely distorted, and even in the center, there is distortion as a result of the small viewing angle. Right: The size of a picture in a magazine matters. The reef shark needs a spread!

interest: It shows an unnaturally distorted shark with giant teeth. Viewers who then see the moving images not only on a small television screen but also from a large distance will easily miss out on the dramatic effect of the original picture (Fig. B.35). They may even sneer at the way the shark’s snout is moving from side to side too quickly. . . Therefore, if you intend to print pictures on a small scale for reasons of space (as in this book, for instance), then you should choose a greater distance (and a telescopic lens) when taking the photos. Smaller geometrical illustrations are best done in normal projection. However, if the pictures are to be printed on a large scale (a photography magazine is a good example), then you may and ought to employ a wide-angle lens (Fig. B.37 on the right). ⊕ Remark : This insight may not be so useful for paparazzi: They may want to publish full-spread photos of their victim’s latest and greatest secrets and are thus more likely to opt for an ultra-wide-angle lens. . . ⊕

Fig. B.38 An extreme wide-angle lens was used in both pictures. On the left, we may be able to “rectify” the scene by using our existing knowledge. On the right, we may make an estimation of the trunk’s thickness.

⊕ Remark : In Fig. B.38 on the left, the extreme wide-angle photo makes for an impressive state room. Our knowledge about columns and chandeliers helps us to estimate its true dimensions. In the right image, an ordinary tree resembles an African baobab with an extremely thick trunk. This might be interpreted as a “distortion of facts”. On the other hand, trees do look this way if we approach them up close and look up. If a poster-sized print of this photograph were to hang at

668

B Geometry and photography

a height of two meters, a person walking under the picture may, indeed, get the impression that they were walking through a forest.

Fig. B.39 Two extreme wide-angle photographs. Left: fall scene with 15–20 m high trees. Right: about 30–40 cm high “thicket” of bushes.

Fig. B.39 shows two scenes that may seem comparable. In terms of actual size, however, they have a similarity ratio of 50 ∶ 1. Ultra wide-angle lenses are rarely used for very short distances, which is why we expect the plant in the right photograph to be much larger.

Fig. B.40 We may also use extreme wide-angle photos in order to send a message or to express a stylistic statement. Such photos elicit responses in either case, since objects which are experienced as being up close usually generate some kind of reaction. Things which may actually be tiny or of “regularly sized” appear gargantuan.

Fig. B.40 shows two further extreme perspectives, both of which convey a certain “message” and may, for instance, be used for stylistic reasons. If one wishes to “drive a point home” and demonstrate the enormous performance of one’s creation, it may be valid to exaggerate the visual effects slightly. . . ⊕

Leonardo’s dilemma

Leonardo da Vinci faced the following problem as he designed his “Last Supper”: The painting measures ten meters in width. The observers would walk next to it at a relatively short distance and look at the various details of the picture. If they stood still, then they would need an “ultra-wide-angle lens”.

B.5 Primary and secondary projection

669

Fig. B.41 Leonardo’s dilemma: Should he distort the heads in extreme perspectives or picture them “normally”? Leonardo wisely chose the latter, because he knew that people were more likely to walk along the 10m painting than stand on a specific spot to view the painting from the “ideal position”.

Consequently, all objects would have to be highly distorted – not only the table and the room, but also the heads of the apostles! Leonardo knew that human beings are most perceptive of unnatural distortions when it comes to heads and facial features. Thus, he settled on a compromise: He distorted the still-life environment to a very significant degree but left the heads completely unaffected!

Fig. B.42 A fisheye perspective of a scene with people along a large front: Here, the objective corrects the distortions and contractions at the edges “in its own way”. Note the deliberate usage of light effects – in this concrete example, the scene is illuminated by bounce lighting from below, which lends the scene a certain mystique.

670

B Geometry and photography

B.6 From below or from above? A horizontal lens axis approximates our usual way of seeing pretty well. Our brain evolved in the “savanna” and is used to processing stereoscopic images of objects which lie at a comfortable distance and are approximately of “our own size” – neither too big nor too small.

Fig. B.43 A frog’s perspective from a bird’s-eye view or a bird’s perspective from a frog’s-eye view?

If the size of an object exceeds our field of vision, then we have to tilt our visual apparatus – either upwards (when looking up at skyscrapers) or downwards (when looking at small objects in front of our feet). Over time, the terms frog’s-eye view and bird’s-eye view have become established. The use of these terms is fine as long as we remember that many animals must perceive images very differently from the way humans do and that this is not merely a difference in scale. According to the rules of central projection, our scene is augmented by one further principal vanishing point: the vanishing point of all vertical straight lines. To critical eyes, images with a pronounced vanishing point tend to appear “more artistic”. The following “message” is thus conveyed by the photographer: The object itself – or my position above it – is very high. So-called slightly tilted edges are almost “painful” to the trained eye. They occur when the vanishing point of the vertical straight line lies far beyond the image (Fig. B.46 on the left). In such cases, the vertical edges of the object appear to be “nearly” parallel. For example, the left edge images turn out to be not quite parallel to the left paper edge, and the right ones, which are rotated in contrary motion, are not quite parallel to the right paper edge.

B.6 From below or from above?

671

Fig. B.44 Worm’s-eye view and bird’s-eye view inside the elliptic towers of the Sagrada Família in Barcelona

Either a shift lens . . . Professional photographers are well aware of this problem. In the era of analogue photography, professionals or amateurs with thick wallets helped themselves by employing so-called shift lenses and a tripod: This special lens enables the photographer not only to take pictures in the direction of the optical axis, but also to “shift” this direction slightly. From a geometrical point of view, a regular central projection is produced. However, one can still fix the camera axis horizontally while simultaneously “looking up” towards the edges of the building. According to the laws of geometry, the edges remain parallel in the image.

. . . or some geometrical know-how The dawn of digital photography has changed various things, and arguably for the better: A primary perspective is captured digitally and may later be changed in an image editing software – a process which may be similar, but is still a lot easier than the darkroom of yore, where a comparable amount of photographic “trickery” took place. Even rectangular images can be deformed in such a way that the edges appear as a general quadrangle, whereas the images of vertical corners appear to be parallel. If we now crop the edges into a rectangle, our wizardry should go unnoticed. Unnoticed? A “geometrician” could easily prove that the new image must have been altered. A small number of tests would be enough – for instance, spatial angles become oblique angles if the distortion is corrected properly.

672

B Geometry and photography

Fig. B.45 Either strongly vanishing vertical edges. . .

Fig. B.46 . . . or exactly parallel vertical edges!

The change which has taken place is, in fact, two-dimensional and thus had no regard for the depth distances of the singular points. Thus, it cannot possibly be exactly correct. For this reason, we should only resort to this trick “in emergencies” – for instance, if we have returned from our vacation with a very special photo of architectural treasure which we cannot possibly replicate. If the following principle is considered before taking the photo, we may be spared a lot of work later on: We should not only take a picture of the relevant object (such as the tall building in Fig. B.48) but also of many other important areas next to it – as long as the optical axis is horizontal. We may even accomplish this without fancy equipment like a bubble level by simply pointing the camera at the heads of people who are situated at a constant height in front of the building. In post-processing, we only have to crop away the “digital junk”. . .

B.6 From below or from above?

673

Fig. B.47 Two extreme perspectives: On the right, the optical axis is horizontal. When such extreme wide-angle lenses (14 mm) are used, one or two degrees in terms of inclination angles result in radically different images. If the subject is worth it, one should work with a tripod and take one’s time.

Fig. B.48 Architecture photos: “slightly vanishing” (tilted) on the left. The bottom half, which was also photographed on the right, is later cropped from the image.

▸▸▸ An ad showing long female legs By now we know that objects appear to be more distorted the further away they are from the optical axis and the closer they are to the lens center. In an ultra-wide-angle photo, heads should, therefore, always be near the principal point. However, do the same rules apply to legs? Let us first consider Fig. B.50. The original picture of the wine glass is seen on the left, and only a section of it is pictured on the right. If the picture were to be put on a billboard, then the relevant section would certainly be chosen – the rest would not be interesting, and besides, it might be a good idea to catch people’s attention through the extreme distortion. This brings us back to the topic at hand. Commercials often show women with unusually, sometimes almost “grotesquely”, long legs. Fig. B.51 shows the kind of tricks that may be employed to accomplish this effect. ◂◂◂

674

B Geometry and photography

Fig. B.49 Three attempts were made to keep the optical axis horizontal by pointing the camera at a far distant point which lies on eye level.

Fig. B.50 The “evacuation” of the principal point

Fig. B.51 Let us now use an ultra-wide-angle lens. The legs should be turned towards the lens. The apparent length of the legs now only depends on what section of the image is being displayed. The flippers reinforce the impression of elongation.

B.7 Collinear distortion of a photo

675

B.7 Collinear distortion of a photo

Fig. B.52 An extreme distortion of a square grid. At the center: with the help of an ordinary image editing software – not line-preserving (collinear). On the right: collinear though the exact application of mathematical equations.

Let us mention a second method by which effects like Fig. B.51 may be accomplished: We can modify photos by collinear transformation, which “turns” arbitrary quadrangles into different but equally arbitrary quadrangles (such as rectangles). This collineation is linear, which means that straight lines are always transformed into straight lines. Fig. B.53 on the left shows an intriguing photo which was taken halfway below and halfway above water. It can instantly be seen that both halves are central projections, albeit with different parameters. The verticals in the upper half vanish in a principal vanishing point, while the vertical edges of the bottom half inside the swimming pool are nearly parallel. On a computer, a collinear transformation was applied to the right image so that the upper vertical lines of the skyscraper and the tree are “bent” to appear parallel to each other.

Fig. B.53 A swimmer’s perspective on the so-called “Badeschiff” – a boat with a pool on top – at the Danube Canal in Vienna

676

B Geometry and photography

However, now a section of the image which fits entirely into a trapezoid must be chosen (image on the right with a red border). A person who only sees the final result may not recognize that the photograph has been manipulated to a certain degree and actually depicts an illusory world which no longer resembles reality. However, somebody with a trained eye might notice that, for example, the edges underwater are no longer exactly parallel.

Fig. B.54 On the left: A snail crawls across the perspective image of a cube. On the right: A collineation was applied to the entire photo so that the cube appears “normal” once again; but what about the snail . . .

In Fig. B.54 on the left, a snail crawls across the perspective image of a cube. The projection of the cube undergoes a second collineation (secondary perspective) by the mere act of photography. On the right, this collineation is “canceled out” by applying another collineation to the entire photo. As a result, the cube looks “normal”, but the image of the snail is completely distorted. Such inconsistencies are quite common these days and may hint at the software used for post-processing. Fig. B.52 shows the admittedly extreme transformation of a square grid by using a renowned software package. The result is clearly not linear, and the grid subdivisions do not appear where they should be if their location is based on reality. The right image could be the photo of a grid from an extreme position.

Fig. B.55 Taking many pictures of a whole projection screen: If one does not stand immediately next to the projector, then the projected image will be distorted in a collinear way. Nevertheless, the rectification of a general planar quadrangle can be done precisely. This allows the detail marked by the red border to be reconstructed with remarkable accuracy, despite the limited resolution of the projection!

B.7 Collinear distortion of a photo

677

It should be noted that it is very well possible for a collinear distortion or rectification of a planar figure to be precise. Fig. B.55 illustrates this claim by a practical example (photo of a medical lecture by Zvi Ram). The following is a geometrically interesting fact: The virus has the form of an icosahedron with a diameter of 1/10,000 mm!

Fig. B.56 The famous Gloriette in Vienna. On the left: Original photo; on the right: Distorted image. The “error” is negligible, since the façade is nearly two-dimensional. To get a picture like the one on the right, an expensive shift lens or a drone to raise the camera a few meters in the air is necessary.

Fig. B.57 On the left: An interesting snapshot of the baptistery in Florence, taken with a compact camera (format 4:3) at night. On the right: A geometrically acceptable manipulation of the photo (format 3:2). The slight bend of the tower on the right is also visible in the original on the left.

Let us consider Fig. B.56 and Fig. B.57 as two final examples: If you have taken an original photo of the Gloriette in Vienna or the baptistery in Florence – with a moderately priced compact camera or a mobile phone – then surely nobody would reproach you for your slight “alterations”. In Fig. B.57 the full moon is visible behind the dome, see also p. 365. Contrary to Fig. B.56, an exact investigation could, rather easily, bring to light the manipulation in Fig. B.57 on the right: This second scene is much “more three-dimensional”.

678

B Geometry and photography

B.8 The problem with the rolling shutter ▸▸▸ Can you trust photographs? The photograph Fig. B.58, which could almost qualify as art, shows what can happen when a flying longhorn beetle (Stictoleptura rubra) is photographed using a very short exposure time (1/2,500 s). The body of the beetle barely moves, while its elytra (wing cases) move significantly faster than its body (they flap during flight). The wings themselves, on the other hand, oscillate at a high speed relative to the beetle’s body.

Fig. B.58 This photograph is not manipulated and shows a flying beetle with wings pointing in opposite direction, accompanied by two “spare wings”. In extreme cases like this, the observer immediately realizes that something must be wrong.

Fig. B.59 shows a beetle of the same species above a plane (a car roof). The author has taken an abundance of photographs showing beetles with wings on opposite sides. Can we take these photographs as “proof” that insects can assume such positions during flight? Luckily, Fig. B.59 shows that, again, there must be something wrong: The shadow of the beetle does not correspond to the spatial situation. Take a closer look at the shadows of the wings in the right image. The left wing, for instance, is again isolated from the body. All this is due to the delay of a few ◂◂◂ milliseconds while scanning the many “lines” of the sensor. ▸▸▸ When the shadows do not match To recreate the above described effect with a technical device, several photographs were taken of a miniature helicopter, roughly the size of a giant dragonfly and with rapidly spinning rotor blades (Fig. B.60).

B.8 The problem with the rolling shutter

679

Fig. B.59 A flying beetle of the same species, again with wings pointing in opposite direction, this time with “wrong shadows”. A certain amount of geometrical experience can help to notice this “shadow problem”.

Fig. B.60 A model of a helicopter with fast rotating rotor blades

Although the images were shot using an extremely short exposure time of 1/32, 000 s, the rotor blades, which are actually symmetrical and not curved, appear distorted (as opposed to the labels on the blades, which can be read ◂◂◂ quite clearly)! ▸▸▸ What every “high-speed photographer” needs to know The so-called rolling shutter effect is an effect that is well-known in the film business and that can occur in photographs or videos of rapidly moving objects. Most cameras cannot expose the whole sensor surface to light at once. Instead, imagine exposure occurring in a line from one side of the image to the other, either horizontally or vertically – a process which takes a short, though not inconsiderable, amount of time.

680

B Geometry and photography

The shutter time of most camera models is usually considerably longer than indicated. Since the exposed sensor is scanned line by line and each scanning of a line takes only a fraction of the shutter time, the exposure time for each line is reduced accordingly. However, it takes the device the same (very short) amount of time to move to the next line, which is once again exposed very briefly. During that period of time, the wings may have covered a certain distance, which then causes effects like skews, wobbles, and smears. ◂◂◂ ▸▸▸ The problem lies in the proximity to reality Image errors may appear so life-like that one is tempted to take them at face value. Especially in high-speed photography, supposedly realistic images must be taken with a pinch of salt! Certain tests should be carried out to check if such image errors are actually possible. Shadows provide the best starting point for this kind of “reality check”.

Fig. B.61 Smaller birds like sparrows have a wing frequency around 15 hertz. This can sometimes lead to rolling shutter effects. Which one of the photos might be “wrong”?

Fig. B.61 shows a selection of the hundreds of photos the author has already taken of flying sparrows. After careful consideration, it turns out that the two photos on the upper right show wing positions that are impossible. The rolling shutter effect appears predominantly when the birds are tilted in flight to one side and the wings in oscillation are at maximum speed. Then, the shutter reaches the wing on top first and in the time it takes for the shutter to reach lower parts of the image, the wings have already changed position. ◂◂◂

B.8 The problem with the rolling shutter

681

▸▸▸ The man that shoots faster than his shadow Referring back to the “wrong shadows” in application p. 678 (Fig. B.60), one might even remember the comics about Lucky Luke, the “man who shoots faster than his shadow”.

Fig. B.62 The “woman, whose mirror image shoots faster than herself” (in landscape format, to demonstrate the “ideal” conditions for the rolling shutter effect to appear)

Inspired by drawings like the one at http://static.tvtropes.org/pmwiki/ pub/images/050711_lucky_luke.jpg, my daughter Sophie painted the “woman, whose mirror image shoots faster than herself”. The painting looks like a photograph that would, in principle, be possible to achieve - but only with a very slow rolling shutter. The following application will show how such a slow shutter might work. ◂◂◂ ▸▸▸ An extremely slow rolling shutter When a copy machine or a scanner stores an image, a rod-shaped sensor within the machine moves continuously from left to right. In every position, the sensor scans a very small rectangular part of the image. All scanned lines are eventually put together to one final image. Usually, the scanned image is static, and therefore, the scanner works like a camera. Since the scanning process takes a while, one might get the idea to move the original image around. In Fig. B.63, the covers of two books where

682

B Geometry and photography

Fig. B.63 Two books rotated on the surface of a scanner during the comparatively slow scanning process

rotated quickly during the scanning process. The result is quite remarkable, and it has only little to do with the original. In the image to the right, the original was rotated so fast that some regions are even depicted twice (take a closer look at the word “The”). ◂◂◂ ▸▸▸ What does the image of a rotating straight line look like? Let us now tackle the given problem from the geometrical point of view and only look at the simplest case. Kinematically speaking, we are looking for a curve that is created as follows (Fig. B.64): A straight line r rotates with constant angular velocity around a point on itself, whereas another straight line s (the shutter) moves horizontally downwards at a constant speed. The intersection point Q belongs to the resulting curve q. r

q

r

q

r q

s s

Q

Q s

Q

Fig. B.64 The image q of a rotating straight line r is the well known trisectrix of Hippias, also called the quadratrix of Dinostratus. From left to right, the ratio between angular velocity and translation speed in the kinematic generation increases.

This problem has already been investigated by the ancient Greeks more than 2, 000 years ago, being one of the oldest examples for a curve that is created through motion. Hippias of Elis called it trisectrix and used it around 420 BC to trisect an angle. Approximately 70 years later, Dinostratus used it to square the circle (and called it quadratrix). Depending on the ration between

B.8 The problem with the rolling shutter

683

angular speed and translation speed, the curve can have quite different shapes (Fig. B.64).

Fig. B.65 Left to right: Increasing ratio between angular velocity and scanning speed

When the line r does not run through the rotation center, things do not change essentially. Fig. B.65 shows the computer simulation of Fig. B.63 with typical matches.

Fig. B.66 Same ratio between angular velocity and shutter speed: The result depends on the instantaneous position of the rotor blades. Note again the artefacts.

In Fig. B.60, we see a photo of the extremely fast rotating rotor blades of a helicopter, taken with a very short exposure time. Here, again, computer simulations (Fig. B.66) shall convince the reader of the correctness of our theoretical considerations. ◂◂◂ ▸▸▸ Photo finish When in a sporting race two or more competitors cross the finishing line almost at the same time, this can sometimes lead to controversies: Even if a photographer, for instance, has taken the shot of their life at the exact right moment, when the supposed winner was crossing the line, the photo could still be misleading. If in Fig. B.67 the camera had been held in landscape

684

B Geometry and photography

mode instead of portrait mode (with the rolling shutter going downwards), the red car could have been declared the winner, because, within the time the shutter needed to reach the red car (a couple of milliseconds), the red car would have moved further along the track.

Fig. B.67 Photo finish: The two cars finish at nearly the same time. In a photo taken with a normal camera in “landscape orientation” and very short aperture time, the red car would probably be the winner even under perfect conditions, due to the rolling shutter effect.

The better solution is to film in high speed mode with a camera in portrait mode (rotated 90○ ). Now the shutter moves from right to left (or vice versa) and the microsecond (1/1000 of a millisecond) to record just one line with only one pixel width can be neglected. The final photo now consists of the whole series of photos as follows: From each single frame, we only take the pixels on the scan line in the middle (the scanning shutter is therefore considered to be fixed in the middle of the image). All those very narrow rectangles are arranged frame by frame (the parameter is then the time). The resulting “photo” can appear unrealistic (faster objects appear shorter) – look at the distorted car tires in Fig. B.67 – but it guarantees the correct photo finish ◂◂◂ (at least to that part of a microsecond we mentioned earlier). Possibilities to avoid the rolling shutter effect The simplest, but by far most expensive way to avoid the rolling shutter effect is to use a camera with a “global shutter” which stores all pixels simultaneously. At the time this book was finished, there were only very few cameras of that design on the market, all of them at a price that is not affordable for amateurs. For single photographs, a photo flash can be used. Then, the whole shutter is open for a comparatively long time, like, for instance, 1/250 of a second. During that time span, a flash is fired in a 1/30, 000 second. If the environment is not too bright, only the artificial light of the flash illuminates the object. High-speed filming in low resolution (max. 2 MB), using certain affordable cameras on the market, also allows to reduce the effect to a high degree (Fig. 11.82).

Literature The book is written in such a way that, ideally, one does not need to consult other sources immediately in order to understand its content. Here we first list literature that is explicitly quoted and then additional recommended literature.

Quoted literature [1] R. Amon: Lexikon der Harmonielehre. Doblinger/Metzler, Wien, 2005. [2] T. Fruchterman, E. Reingold: Graph Drawing by Force-directed Placement. Software - Practice and Experience 21/11 (1991), 1129–1164. [3] G. Glaeser: Fast Algorithms for 3D-Graphics. Springer Verlag, New York, 1994. [4] G. Glaeser, H. Stachel: Open Geometry – Open GL + Advanced Geometry. Springer, New York, 1997. [5] G. Glaeser, H.P. Schröcker: Geometric Programming Using Open Geometry GL. Springer, New York, 2002. [6] G. Glaeser: Geometrie und ihre Anwendungen in Kunst, Natur und Technik, 3nd ed . Spektrum Verlag, Heidelberg, 2014. [7] G. Glaeser: Geometry and its Applications in Arts, Nature and Technology. Springer Wien New York, Vienna, 2012. [8] G. Glaeser: Nature and Numbers – A Mathematical Photo Shooting. Birkhäuser, Edition Angewandte, Vienna, 2014. [9] G. Glaeser: Math Tools – 500+ Applications in Science and Arts. Springer International London, 2017. [10] G. Glaeser, F. Gruber: Developable Surfaces and Contemporary Architecture. Mathematics and the Arts 1 (2007), 1–15. [11] G. Glaeser, W. Nachtigall: The Evolution and Function of Biological Macrostructures. Springer Nature, Berlin Heidelberg, 2019. [12] G. Glaeser, H. F. Paulus: The Evolution of the Eye. Springer Nature, Berlin Heidelberg, 2014. [13] G. Glaeser, H. F. Paulus, W. Nachtigall: The Evolution of Flight. Springer Nature, Berlin Heidelberg, 2017. [14] G. Glaeser, K. Polthier: Bilder der Mathematik . Springer, Heidelberg, 2014. [15] O. Röschel: New models of moveable polyhedra. In V. Mykhailenko (ed.) Proceedings, 10th Int. Conf. on Geometry and Graphics Volume 1, pp. 127-131, 2002. [16] G. Glaeser, H. Stachel, B. Odehnal: The Universe of Conics. From the ancient Greeks to 21st century developments. Springer-Spektrum, Springer-Verlag, Heidelberg, 2016. [17] G. Glaeser, B. Odehnal, H. Stachel: A Spatial Theorem of the Angle of Circumference. Journal for Geometry and Graphics Volume 23 (2019), No. 2, 147–156. [18] F. Gruber, G. Wallner, G. Glaeser: Force directed near-orthogonal grid generation on surfaces. Journal for Geometry and Graphics, 14/2 (2010), 135–145. [19] D.R. Hofstadter: Gödel, Escher, Bach. An Eternal Golden Braid . Harvester Press, Hassocks, 1979. © Springer Nature Switzerland AG 2020 G. Glaeser, Geometry and its Applications in Arts, Nature and Technology, https://doi.org/10.1007/978-3-030-61398-3

685

686

Literature

[20] B. Mandelbrot: The Fractal Geometry of Nature. Freeman San Francisco, 1982. [21] M. Kac, S. Ulam: Mathematics and Logic: retrospect and prospects. Penguin Books, Harmondsworth, 1992. [22] B. Odehnal, H. Stachel, G. Glaeser: The Universe of Quadrics. SpringerSpektrum, Springer-Verlag, Heidelberg, 2020. [23] R. Tamassia: Handbook of graph drawing and visualization. Chapman & Hall/CRC, Boca Raton, FL, 2014. [24] D.W. Thompson: Growth and form. Cambridge University Press, 2nd ed., 1959. [25] G. Wallner, F. Gruber: Interactive Modeling and Subdivision of Flexible Equilateral Triangular Mechanisms. KoG, 15 (2011), 50–56. [26] H. Walser: Semi-Regular Figures Between Beauty and Regularity. In C. Michelsen, A. Beckmann, V. Freiman, and U. T. Jankvist (ed.), Mathematics as a Bridge Between the Disciplines, 29–38. LSUL, 2018. [27] W. Wunderlich: Darstellende Geometrie I, II . Bibliographisches Institut, Mannheim, 1966/67. [28] W. Wunderlich: Ebene Kinematik . Bibliographisches Institut, Mannheim, 1971.

Additional recommended books [30] M. Berger: Geometry I, II. Translated from the French by M. Cole and S. Levy. Springer, Berlin, Heidelberg, 1987. [31] J.L. Coolidge: A Treatise On The Circle And The Sphere. American Mathematical Society, Providence, Rhode Island, 2004. [32] H.S.M. Coxeter, S.L. Greitzer: Geometry revisited . The Mathematical Association of America, Washington, D.C., 1967. [33] E.D. Demaine, J. O’Rourke: Geometric folding algorithms: linkages, origami, polyhedra. Cambridge University Press, Cambridge, 2007.. [34] P.M. Gruber, J.M. Wills (eds.): Handbook of Convex Geometry. Vol. A, B.. North Holland, Amsterdam, 1993. [35] D. Hilbert, S. Cohn-Vossen: Geometry and the Imagination. Chelsea, New York, 1999. [36] W. Kühnel: Differential Geometry. American Mathematical Society, Providence, Rhode Island, 2015. [37] L. Piegl, W. Tiller: The NURBS Book . Springer, Berlin, Heidelberg, 1995. [38] H. Pottmann, A. Asperl, M. Hofer, A. Kilian: Architectural Geometry. Bentley Institute Press, Exton, PA, 2007. [39] H. Pottmann, J. Wallner: Computional Line Geometry. Springer, Wien/New York, 2001. [40] J. Richter-Gebert: Perspectives on Projective Geometry: A Guided Tour Through Real and Complex Geometry. Springer, Berlin, Heidelberg, 2011. [41] D.J. Struik: Lectures on Classical Differential Geometry. Dover Publications, New York, 1961. [42] J.M. Wills (ed.): Handbook of Convex Geometry. Vol. A, B.. North Holland, Amsterdam, 1993.

Literature

687

Picture credits The book contains more than 2000 computer renderings, photos, and freehand drawings, distributed over approximately 1,000 figures. The following figures have been used (with courtesy of the authors), without displaying the names of the photographer / artist: 2.12 Photo on the left: Reiner Zettl 3.71 Photo on the left: Eberhard von Nellenburg, photo on the right: Cédric Thévenet 4.83 Liddy Scheffknecht, oculus, 2012, Sonnenlicht, Erdrotation, Papier, Lampe, © Liddy Scheffknecht and Bildrecht Wien 5.20 Gerald Zugmann 5.21 Gerald Zugmann, Paula Goldman 6.53, 10.26 Statikbüro Bollinger/Grohmann/Schneider, Metallbau Pagitz 6.96 Matthias Ecker 6.114 Photo on the right Karin Pfaffstetter-Odehnal 6.115 ISOCHROM.com, Vienna 7.67 Photo on the right: Christian Perrelli 9.4, 9.82 Harald Andreas Korvas (sodwana.uni-ak.ac.at/korvas) 9.11 Photo on the left: Othmar Glaeser 9.28 Photo on the left: Elisabeth Halmer 9.28 Photo on the right: Torre Annunziata / Villa di Poppea, credit: B. Andreae, Neue Forschungen in Pompeji und den anderen vom Vesuvausbruch 79 n.Chr. verschütteten Städten (1975) Abb. 26, Database: HeidICON - Klassische Archäologie, Ruprecht-Karls-Universität Heidelberg A.30 Photo on the left Othmar Glaeser 9.87, 9.88 artpool.cc (www.artpool.cc/marianne, www.artpool.cc/grisei) 13.39 Helen Binet Studio, 24a Bartholomew Villas, London NW5 2LL, U.K. B.57 Romana König

Index

A

ability, 68 absolute points, 194, 276 accompanying tripod, 134 acoustic, 240 adhesion, 279, 538 affine mappings, 234 affine ratio, 30, 58 age of rocket science, 264 air resistance, 200 air rifle, 342 Alberti, 2 Alexander the Great, 380 algorithm, 141 Alhambra, 514 aliens, 577 altitude theorem, 36 aluminum, 209 aluminum layer, 215 ambient space, 52 amusement park, 470 analogue, 493 analogue photography, 671 anamorphosis, 228, 376 android, 424 anemone, 280, 291 angle, 59 angle bisector, 14, 33 angle of circumference, 9, 301 angle of elevation, 481 angle of view, 639 angular momentum, 495 angular velocity, 484, 496 animal figures, 383 animate, 99 annular sector, 178 annulus, 423 ant, 508 anti-complementary triangle, 14 anti-inverse, 36 antiparallelogram, 428 antipode, 219, 220 antiquated, 99 aperiodic tiling, 529 aperiodicity, 522 apex, 93, 185 apex of a star, 46 apices of the ellipse, 127 Aplysia, 335 Apollonius of Perga, 30 apparent solar time, 484 apparent time, 474 approximate polyhedron, 281 approximate straight line guidance, 433, 434 approximation techniques, 227 arc length, 128, 129, 167 arched bridge, 191 Archimedean screw, 305 Archimedean solid, 87, 123 Archimedean spiral, 316 Archimedean tiling, 520 Archimedes, 7, 22, 109, 306, 533 architectural firm, 184 architecture, 1, 56, 95, 151, 163, 182, 209, 245, 278, 291–293, 300, 341, 370, 473 articulate animal, 552 artificial light, 99 ashtray, 142 assignment problems, 68

asteroid belt, 547 astigmatism, 279 astroid, 23, 418, 419, 452 astronomy, 1 asymptotes, 197 atomic clock, 493 auxiliary apex circle, 121 auxiliary view, 67 axioms, 8, 28 axis of affinity, 119, 120 axis of collineation, 119, 375 axis of perspectivity, 118, 119 axis of symmetry, 84

B

B-spline curve, 352 Bach, 558 back lighting, 632, 635 back view, 69 backlight, 371 ball joint, 464 bamboo stool, 174, 251 Bangalore, 222 baobab, 667 baptistery, 677 barrel vault, 166, 550 base line, 370, 625 base plane, 39, 370, 625 basic building block, 517 Basilica di Santa Prassede, 518 bat, 471 beam connection, 166 Bedouin, 535 beer mat method, 18 beetle, 534 bellflower, 282, 283, 620 bending machine, 356 bending procedure, 173 Berger, 523 Berlin, 237, 485 Bernhardt, 493, 497, 499, 500 Bernoulli, 420 bevel wheels, 464 Bézier curve, 351, 352, 530 Bézier spline, 352 Bézout’s theorem, 168, 253 bicycle, 416, 417, 629 Biedermeier period, 437 Big Bang, 52, 421 Big Crunch, 52 bilateral symmetry, 534 Bilateria, 534 Bilbao, 300 billiard ball, 62 binormal, 134, 207 biology, 1, 548 bird’s perspective, 670 bird’s-eye view, 608, 609, 670 Blender, 503 blending surface, 289, 291 blind hole, 308 bluebell, 271 Boeing, 353 bolt, 307 Bolyai, 49 Bonnet’s theorem, 333 Boolean operations, 361 bottom view, 69, 166 bounce lighting, 669 boundary circle, 269

Index boundary surface, 401 Boy’s surface, 336 boy-scout rule, 483 braces, 84 brachistochrone curve, 420 brain power, 410 brandy glass, 142 Brianchon, 192 Brianchon point, 193 brightness, 537 brown algae, 335 Bruegel, 316 Brunelleschi, 152, 236, 364, 365 bubble level, 672 Buenos Aires, 222 bumpy road, 192 burdock, 652 burning mirror, 239 butterfly wing, 216

C

C-major tonality, 558 Calatrava, 296, 300 calendar year, 473 camera obscura, 413 camouflage, 662, 663 Cape of Good Hope, 490 car body, 265 carcinus maenas, 536 Cardan circle, 441, 447, 450, 452 Cardan shaft, 435, 443, 462, 463 Cardano, 441 cardioid, 452 carnivore, 552 carpenter bee, 426 carrier cylinder, 303 carrier line, 6, 25 carrier plane, 33 carrier surface, 264 carrier surfaces of revolution, 546 cartography, 217, 219 Cassini oval, 31, 275 cast-shadow boundary, 147 cat, 60, 66 cat’s eye, 62 Catalan, 114, 333 Catalan solids, 114 catenary, 190, 192, 629 catenoid, 281, 326, 327, 330, 333 caustic, 213, 231 CCD, 639 ceiling paintings, 386 celestial axis, 494 celestial equator, 497 celestial pole, 476, 494 celestial sphere, 493 cell nucleus, 307 center of collineation, 119, 375 center of curvature, 261 center of projection, 54 center of the globe, 221 central lighting, 370 central perspectivity, 118, 122 central projection, 162, 236, 367, 670 central shadow, 120 central similarity, 14 central view, 608 centrically similar, 517 centrifugal force, 180 centroid, 13 ceramic lens, 358 ceramics, 340 Cetoniidae, 509 chain of spheres, 576 chain reaction, 549 chair tiling, 522 chandelier, 100 channel surface, 288, 318 chariot, 380 chemistry, 1

689 chess figure, 424 chess-playing Turk, 424 Chillida, 342 chitin exoskeleton, 411 choreography, 548 chromosomes, 307 circle, 303 circle conoid, 295 circle of Apollonius, 31 circle of circumference, 19 circle of fifths, 556, 557 circle of latitude, 268 circle of longitude, 50 circle reflection, 42 circle’s involute, 127 circular, 275 circular conoid, 249 circular helical surfaces, 311 circular sector, 177 circumcenter, 13, 43, 127 circumcircle, 13 circumpolar star, 476 circumsphere, 108, 113 Citroën, 351 city map, 59 civil engineering, 1 classical spiral motion, 317 clearance hole, 308 clipping, 377 clock-face, 494 clothoid, 129, 578 Cloud Gate Chicago, 227 cockchafer, 509 cockpit, 400 cogwheel, 464 cohesion, 538 collinear mappings, 234 collineation, 252, 382, 676 collision, 73 color fastness, 661 columns, 197 Commodore Amiga, 99 complex surfaces, 339 composite photograph, 60 compound computation of interest, 318 compound eye, 140, 401, 410 computational geometry, vi computer geometry, 96, 283, 471 computer graphics, vi, 274, 397 computer simulation, 319, 409, 424, 495, 497, 547 conchoid, 23 cone of constant slope, 203 cone of revolution, 33, 176, 234, 270, 478, 575 cone rolling, 461 confocal conic sections, 187 conformal, 220 conformality, 225 congruence of rays, 498 congruence relations, 45 congruence transformations, 88 congruent, 7 conic, 37 conic section, 23, 30, 47, 196, 199, 494 conic section construction, 196 conic wheels, 179 conjugate diameters, 380 connect, 38 connecting developable, 210 connecting line, 34, 142 connecting plane, 220 connecting surface, 180 conoid, 295, 296 conservation of angular momentum, 545, 546 conservation of momentum, 548 constrained motion, 416 construction drawing, 86 construction of the unfolding, 68 contact circles, 35 contact lenses, 279 contact point, 38

690 continuity of curvature, 353 continuous line, 84 contour, 137 contour cusp, 280 contour ellipse, 365 contour generator, 618 contour hyperbola, 616 contour line, 137 contour point, 137 contour polygon, 96 control grid, 355 control points, 347 control polygon, 351, 352 convex, 93 cooling fan, 305 cooling tower, 250 coordinate directions, 635 coordinate grid, 219 coordinate origin, 68 coordinate plane, 67 coordinate system, 39 copy machine, 681 coral colony, 540 coral fish, 60 corkscrews, 307 cormorant, 549 cornea, 409 corner of a cube, 63 coronavirus, 346 corrective lens, 279 coupler curve, 436 course angle, 222, 276 crane, 426, 433 crank shaft, 430, 446 crank shaft gear, 446 crank shaft propulsion, 431 crease pattern, 116 crescent moon, 157 crocodilefish, 664 crop circles, 577 crop factor, 639 cross-view, 655 crosshair, 624 crotch, 7 Crustaceans, 401 Crux, 490 cryo-electron tomography, 346 crystal formation, 525 Cuba, 160 cube, 102, 103, 105, 341, 518, 528, 608, 609, 676 cube apartment, 341 cubic circle, 147, 255, 256 cubic parabola, 256 cubic splines, 347 cuboctahedron, 222 cuboid, 75, 635 culmination point, 474, 483 curvature, 129, 139 curvature jump, 265 curvature line, 262 curvature radius, 409 curvature tangent, 261 curve normal, 126, 133 curve of constant width, 448, 449 curve of regression, 295 curve on the sphere, 285 curve tangent, 133 cusp, 135, 419 cyclide, 232, 287 cycloid, 304, 419, 420, 499 cycloid gear, 456 cycloid motion, 419 cycloid sundial, 499 cylinder, 162 cylinder axes, 616 cylinder generator, 165 cylinder model, 532 cylinder of revolution, 32, 161, 173, 234, 291, 303, 575 cylinder surface, 354

Index cylindrical projection of the sphere, 396

D

Dürer, 516 Díaz Moreno, 573 Díaz Moreno, vi daisy, 544 Dandelin, 164, 187 darkroom, 671 date lines, 494 de Boor, 353, 354 de Casteljau, 351–354 de la Hire, 121, 466 dear, 503 deflation, 522 degree of symmetry, 285 degree-three curve, 255 degree-two curve, 185 deoxyribonucleic acid (DNA), 307, 314 depth amplification, 659 depth line, 369, 625 depth of field, 399, 400 depth shortening, 659 Descriptive Geometry, 53 desert, 408 design, 1, 182, 238, 239, 282, 283, 292, 296, 342, 343, 347, 350, 354, 355 determination of visibility, 72 developable, 175, 295, 309 developable surface, 38, 283, 360 development, 68, 104, 332 diacaustics, 406 diagonal direction, 626 differential equation, 191 diffraction, 216 digital camera, 639 digital photography, 671 digon, 448 dimension, 5, 34 dimensional jump, 46, 50 diopter, 280 directing plane, 295 direction of a straight line, 29 directions, 249 directly congruent, 8, 88 director, 188, 197, 295, 296 discrete family, 342 distance, 368 distance circle, 29, 368 distance line, 32 distance of the jump, 61 distance of translation, 302 distance plane, 32 distance points, 626 distance sphere, 152 distance surface, 32 distortion, 677 division of hours, 493 division plane, 401, 405 dodecagon, 518 dodecahedron, 103, 105, 106, 141, 357, 516, 531 dome, 550 dome construction, 236 dominant parallel, 558 dot product, 96 double cone, 176 double cushion, 62 double exposure, 390 double helix, 307, 314 double point, 183 double reflection, 63 double screw, 306 double solution, 29 double subdominant, 558 double-horn, 575 downpour, 407 drill bit, 443 driveshaft, 41, 463 driving rod, 432

691

Index drizzle, 408 dual spaces, 35 dumbbell, 179 Dupin, 261, 287 Dupin cyclide, 575 Dupin indicatrix, 327 duration period, 493 Dürer, 624, 630

E

E-minor, 558 Earth’s axis, 484 Earth’s circumference, 264 east, 473, 482, 485, 498, 499 eccentric, 465 ecliptic, 80, 455, 473 edge centroid, 13 edge of regression, 208, 295, 361 egg cocoon, 401 eight-shaped loop, 497 Einstein, 52 elastic band, 117 elbow, 84 electric motor, 455 elements, 192 Elements of Euclid, 28 elephant, 552, 659 elevation angle, 476 elixir of life, 401 ellipse, 45, 48, 122, 192, 195, 352, 365, 390, 400, 421, 428, 608–610, 612, 613, 615–617 ellipse compass, 440, 446, 447 ellipse motion, 440, 446, 448, 450 ellipsoid, 198, 254 ellipsoid of revolution, 237, 262, 284, 406 elliptic cylinder, 173, 234 elliptic paraboloid, 242 elliptic plane, 50 elliptic point, 140 elytra, 509 engineer’s view, 611 enharmonically, 556 Enneper’s surface, 332 envelope, 23, 129, 272, 418, 421 envelope of straight lines, 419 enveloping cone, 145 Epibulus insidiator, 508 epitrochoid, 450, 451 epitrochoid motion, 444 equation of time, 459, 483, 484, 493–499, 501, 502 equator circle, 269 equilateral, 101 equilateral hyperbola, 130 equilibrium, 18, 141 equinoctial line, 453 equinox, 80, 477, 488, 494–496 Eratosthenes, 264 Escher, 20, 274 Escher, Maurits Cornelis, 232 Euclid, 10, 28, 29, 49 Euclid’s theorem, 36 Euler, 89, 101, 333 Euler characteristic, 101 Euler line, 14, 17 Euler spiral, 311 evolute, 126, 127, 147, 421, 579 evolute developable, 146 evolution, 542 exact straight translation, 41 excavator shovels, 306 excenter, 15 excircle, 15 exit angle, 407 experience, 366 exploded drawing, 502 explosion sketch, 183 exponential function, 191 exposure time, 200 external dimension, 85

extreme position, 665 eye height, 625 eye lens, 401 eye point, 624 eye position, 366 eyeball, 365

F

facet, 410 factor of proportion, 302 factor of similarity, 8 families of straight lines, 247, 250, 251 family of circles, 275 female legs, 673 Ferguson, 353 Fermat, 19 Fermat point, 19 Feuerbach, 17 Fibonacci, 542 Fibonacci number, 524 fine arts, 1 fireworks, 25 fish scales, 216 fisheye image, 399 fisheye lens, 397, 398, 639 fitness machine, 436 fixed circle, 450 fixing mechanism, 435 flashlight, 139, 662 flat point, 135, 140 flat washers, 84 flight path problem, 222 flight simulator, 469 Florence, 677 Florence Baptistery, 364 Florentine pattern, 517 flowchart, 513, 514 flower, 117 flower chafer, 509 flying fox, 411 focal curve, 498 focal length, 399, 629, 639, 640 focal line, 214, 231, 421 focal mirrors, 187 focal plane, 213 focal point, 29, 186 focal point property, 239 focal properties, 186 focal ratio, 637 focal rays, 187 focal surface, 213, 498 focusing effect, 214 fool’s gold, 104 foot of the rainbow, 408 foot of the Sun, 371 football, 532 Foster, 325 four-bar linkage, 432, 435 four-eyed fish, 401 Fourier, 458 Fourier series expansion, 458 free-form surface, 337, 342, 360 Frenet frame, 134 frieze ornament, 512 frog’s-eye view, 670 front lighting, 632 front view, 63, 67, 69, 83, 84, 113, 167, 373, 378, 484, 608 frontal line, 625 frontal perspective, 367, 625 frontal plane, 625 frontal projection, 609 Fruchterman/Reingold, 141 fruit bowl, 238 frustum, 54, 178, 219 Fuhs, 444 full moon, 156, 488, 489, 677 full section, 85 full-format sensor, 639 full-frame cameras, 639

692 Fuller, 124, 222 function graph, 339, 340, 458 fundamental cell, 512 fundamental theorem of algebra, 169

G

Gaspard Monge, 67 Gaudí, 191 Gaudí, 248, 296, 305 Gauss, 49, 382 Gaussian collineation, 382 Gaussian curvature, 333 Gaussian image, 285 gear flanks, 310 gear rack, 435 general theory of relativity, 52 generating polygon, 93 generator, 175, 295 geodesic, 253 geodesic curve, 142–144, 180 geodesic line, 135, 174, 206 geographical latitude, 477, 484 geography, 1 geoid, 236 Geomag, 101, 106 geometry in a star, 46, 50 Gherkin tower, 325 Gibbs, 493, 500 giraffe, 505, 553 glass façade, 209 glasses, 278 Global Positioning System (GPS), 159 global shutter, 684 globe, 28, 159, 160, 175, 217, 218, 220–223, 236, 264, 612, 613 Gloriette, 677 glowing chunks, 546 golden mean, 542, 544 golden ratio, 523 GPS-satellites, 160 Granada, 514 gravitational lensing, 28 gravity, 472, 546 great circle, 141, 150, 223, 253, 453 great circle on the celestial sphere, 493 great dodecahedron, 107 great icosahedron, 107 great stellated dodecahedron, 107, 117, 528 grid of keys, 557 grid point, 355 grinding, 252 groin vault, 166 ground control station, 152 ground plane, 70 growth, 537 Gullstrand, 409 gyroscopic motion, 474

H

half pipe, 171 half-ellipse, 156, 157 half-ellipsoid, 100 half-section, 84, 85 half-torus, 273 hall of columns, 381 handle point, 135 hard coral, 664 hardware, 410 harmonic oscillation, 89, 300 harmonic pendulum, 421 harmony, 556 Hart, 41 Hauck, 396 Hauck’s perspective, 396 Hawking, 50 hazel leaf roller, 145 head motion, 665 headlights, 242 Heidelberg, 123 helical developable, 310

Index helical minimal surface, 333 helical motion, 135, 315, 459 helical pipe surface, 313 helical ruled surface, 558 helical stairs, 618, 619 helical surface, 299 helicoid, 323, 326, 327, 333 helicopter, 101 heliochronometer, 500 helispiral, 316 helispiral motion, 321, 347 helix, 37, 114, 135, 144, 174, 299, 302, 303 herbivore, 552 hereditary material, 307 hexahedron, 103 high-speed photograph, 342 highlights, 139 highway entrance, 311 hinge, 297 hinge joint, 423 hinge parallelogram, 426 hinge quadrangle, 432 hinge trapezoid, 435 Hippias of Elis, 682 hoax, 577 Hoecken, 446 Hofmann, 493, 500 Holbein the Younger, 376, 377 hollow bodies, 98 hollow wheel, 441 horizon, 368, 625 horizontal projection, 59 horizontal view, 375 horse latitudes, 500 hot-air balloon, 383 hour index, 496, 498–501 hour lines, 494 HP shell, 86 HP surface, 248 Huygens, 421 hyperbola, 29, 86, 122, 123, 170, 175, 186, 192, 195, 197, 199, 245, 252, 352, 478 hyperbolic paraboloid, 86, 242, 245, 263, 297, 298 hyperbolic plane, 50 hyperbolic point, 140 hyperbolic spiral, 137 hyperbolically curved, 140, 270, 295 hyperboloid, 234, 245, 247, 248, 251, 262, 281 hyperboloid of revolution, 245, 247, 250, 270, 406 hypersphere, 225 hypoid gear, 252, 468 hypotrochoid, 450 hypotrochoid motion, 443

I

icosahedron, 105, 106, 140, 141, 610, 677 iff (if and only if), 77 image construction, 409 image diagonal, 639 image editing software, 671 image plane, 54 image point, 54, 399 image raising, 404, 405 image situation, 666 impeller, 306 implicit equation, 238, 300 incidence relation, 45 incircle, 14 indicatrices, 261 indirectly congruent, 90 individual, 541 industrial Design, 238 infinite, 25, 34, 139, 150 infinitely, 23, 39, 57, 261 infinity, 5, 34 inflation, 522 inflationary kite, 524 inflationary rhombuses, 524

693

Index inflection point, 97, 135, 351 initial capital, 318 initial radius, 537 inner circle rolling, 441, 443 insect eye, 410 insphere, 108 instantaneous axis, 461, 462, 468 instantaneous pole, 417, 431 instantaneous velocity, 418 intercept theorem, 59, 120 interference, 215, 421 interference color, 391 interpolating curves, 347 intersect, 38 intersection, 282 intersection curve, 183 intersection method, 367, 369, 625 intraocular fluid, 409 inverse kinematic, 504 inverse kinematics, 506 inverse matrix, 121 inversion, 40, 42, 578 in a circle, 574 in a sphere, 574 of a cylinder, 575 of a torus, 575 inversion sphere, 41 inverting linkage, 41 involute, 131 involute gear, 252, 310 involute gearing, 456 involute of a circle, 130 iris, 366 isometry, 609 isosceles, 101

J

jet streams, 159 jump, 259 Jupiter, 454, 490

K

Kapoor, 227 Kepler, 107, 200, 270, 476, 484, 495 Kepler equation, 495 Kiepert, 17, 19, 20, 119 Kiepert’s theorem, 19 kinematics, 10, 92, 194, 415, 459, 462, 466 kissing number problem, 153 knot vector, 353

L

label, 173 lacrimal fluid, 280 ladybird, 539 ladybug, 198 lampshade, 199 large scale, 265 large-scale weather pattern, 545 laser scanner, 347 lateral acceleration, 465 lathe tool, 422, 445 latitude, 222 law of inertia, 546 law of planetary motion, 474 law of reflection, 62, 564 law of refraction, 404 Law of Right Angles, 45, 75, 76, 79–81 Le Corbusier, 182 LED lamp, 304 left and right view, 83 left helical motion, 302 left side view, 69 left-handed, 316 Leitner, 240 lemniscate, 130 length of day, 480 lens, 279 lens eye, 391

lens formula, 643 lens system, 278 Leonardo da Vinci, 2, 67, 426, 431, 438, 444, 470, 471, 668 letter scale, 427 Leys, 530 light center, 96 light edge, 354 light flare, 162 light games, 215 light path, 640 light plane, 370, 372, 622 light rays, 52, 370 light sensitivity, 273 light source, 390 light year, 23 lighting, 95 lily, 271, 620 limaçon, 23 limaçon, 204 limaçon of Pascal, 130, 452 limaçon of Pascal, 451 limestone shell, 284 limiting cone, 404 limiting position, 126, 134, 417 line at infinity, 26, 27, 35, 45, 48, 56 line element, 194, 629 line of action, 456 line segment, 25 line space, 35, 37, 39 linear combinations, 184 linear mapping, 55 linkage motion, 432 lion, 504 Lipkin, 41 load capacity, 191 Lobatschewskij, 49 locus, 23 locus curve, 31 logarithmic spiral, 127, 130, 577 long distance beams, 242 longhorn beetle, 678 longitude, 222 longitudinal section, 84 loops of dimensions, 85 loss of information, 42 low-pressure turbulence, 545 loxodrome, 276, 578

M

Mad House, 464 magic cube, 88 magnetic repulsion, 516 main normal plane, 406 main theorem of spatial kinematics, 468 Maltesian gear, 437 marionette, 424 marquee, 558 Mars, 490 masonry drill, 311 mathematician, 264, 303 mathematics, v, 6, 28, 39, 102, 270, 339, 533 matrix notation, 121 mayfly, 651 mean curvature, 327, 328, 333 mean location time, 493 mean noon, 493 measurement of angles, 50 measurement point, 628 measuring inaccuracy, 285 mechanical engineering, 1, 2, 282, 292, 310 medial triangle, 14 median, 13 Mediterranean, 9 Melolontha melolontha, 509 mental arithmetic, 22 Mercury, 326, 454, 490 meridian circle, 274, 578 meridian circular helical surface, 312 Meusnier, 260, 261

694 microcosm, 87, 533 mid helix, 313 midsurface, 322 mill, 469 mill flanks, 311 milling machine for ellipses, 443 milling process, 343 minimal spiral surface, 333 minimal surface, 293, 326, 555 minor key, 556 mirages, 409 mirror plane, 90 mirror window, 633 Möbius, 332 mole grips, 434 molecular biology, 1, 307 molecule, 307 Monge, 67, 282 Moon, 546 moon crescent, 155 moonset, 370 Morley, 17, 20–22 Morley’s theorem, 20 mosquito, 534 most irrational of all numbers, 544 moth, 534 multicuspidal curves, 452 multiple section, 84 murals, 381 muscle contraction, 401 muscle diameter, 552 music, 1 mutation, 541 mystique, 669 Möbius strip, 208

N

nadir, 482 Napoleon, 42, 43 nautilus, 348 Navigation system, 158 Nazca culture, 383 needle cyclide, 575 neighboring apex, 166 neighboring generators, 248 neighboring point, 127 nephroid, 294, 452 Nepomorpha, 401 Neutrino, 52 new moon, 157, 489, 490 New Year’s Eve, 25 Newton, 153 Newton ring, 421 Nile delta, 9 nine-point-circle, 18 non-Euclidean geometry, 49 normal congruence, 406 normal developable, 134, 206 normal direction, 285 normal projection, 162, 236 normal section, 139, 206, 261, 262 normal view, 97, 608, 658 north direction, 277, 481, 484 North Pole, 156, 478, 578 North Star, 389, 476, 490, 494 north winter, 478, 489 northern direction, 476 Northern Tropic, 481, 482 nozzle, 84 null circle, 150 numerologists, 544 nut, 84, 307 nutation, 495

O

oblique circular cylinder, 171, 234 oblique projection, 59, 608 oblique view, 59, 608 octahedron, 105, 106, 141 offset, 302

Index offset curve, 131, 419 oil pump, 433 Oldham, 445 Oldham coupling, 445 olive presses, 307 Oliver, 493 oloid, 208, 210, 267, 285 Olympic Stadium, 328 ommatidia, 411, 651 one-sheeted hyperboloid, 245, 247, 468 one-sheeted hyperboloid of revolution, 246, 249, 264, 615 ophthalmologist, 278 optical illusion, 381, 653 optician, 278 orb-weaver spider, 535 orca, 73 ordering line, 67 orders of magnitude, 552 orientation, 7 origami, 115 original photo, 375 ornament, 512 orthocenter, 13, 376 orthogonal distance, 32 orthogonal trajectory, 535 orthonomic curves, 130 oryx, 505 oscillate, 347 oscillation curves, 300 osculating circle, 126, 127, 133, 146, 242, 259– 262, 278, 578, 579 osculating parabola, 260 osculating plane, 134, 135 osculating sphere, 240, 241 ostrich, 506 Otto, 430 Otto engine, 430 outer circle rolling, 444 outer space, 293, 472, 476, 480, 546, 548 outline, 138 outline generatrices, 196 outline of a sphere, 154 oval mill, 444 own weight, 552

P

Packaging material, 117 pair of angle bisectors, 15 Palmenhaus, 166 panoramic view, 384 paper snippets, 389 paper strip construction, 440 paper strip method, 194 Pappus, 193 parabola, 86, 122, 123, 175, 199, 200, 241, 298, 351, 352 parabolic headlamp, 233 parabolic headlights, 242 parabolic point, 140 parabolic trajectories, 199 paraboloid, 234, 355 paraboloid of revolution, 241, 242 parachute, 73 parallel circle, 268 parallel curve, 419 parallel curves, 131 parallel key, 557 parallel lighting, 370 parallel pair, 32 parallel perspectivity, 118 parallel postulate, 51 parallel projection, 58, 163 parallel section, 9 parallel shadow, 61, 120, 163 parameter interval, 299 parameter representation, 247, 255, 299, 300, 440 parasitic points, 283 partial section, 85 Pascal, 192, 193, 196, 451

695

Index Pascal line, 193, 196 path circle, 149 path ellipse, 495 path normal, 418 path tangent, 418 paving slab lifter, 127 peacock, 268 peacock’s feather, 8, 90 Peaucellier, 41 pedal point, 418, 460 pedestrian bridge, 300 pelvis height, 61 pencil, 617 pencil of lines, 46 pencil of rays, 535 pencil sharpener, 469 pencils of parallels, 298 pendulum clock, 421 Penrose, 523 pentagondodecahedron, 516, 528 pentagram, 107 penumbra, 622 penumbra shadow, 99, 103 penumbral boundaries, 623 pepper grinder, 424 perception, 363 period duration, 488 periodic pattern, 512 peripheral circle, 447 perpendicular bisector, 11, 16, 127, 417 perspective, 56, 236, 608, 658 perspective affinity, 118 perspective collineation, 118 perspectivity, 46 perspectivity ray, 118 phase-shifted, 303 photo finish, 684 photograph, 1, 55, 66, 160, 376, 394, 399, 400, 666 photography, 54, 58, 365, 383, 398, 637, 638 photography magazine, 667 phyllotaxis, 542 physical reflection, 42 physicist, 236, 547 physics, 1, 2, 13, 28, 49, 52, 293, 412, 471, 525 Piazza San Marco, 638 Pilkington, 493, 500 pine tree trunk, 32 pipe connection, 168 pipe elbow, 164, 165 pipe surface, 288, 318 piston chamber, 452 piston engine, 431 pitch, 618 Piva, 245 pixels, 391 plan view, 63, 67, 69, 83, 113, 167 planar perspective affinity, 119 planar perspective collineation, 119 plane at infinity, 27, 57 plane of reference, 68 plane space, 5, 35, 39 plane stance, 27 planes of symmetry, 236 planetary gears, 455 planetary motion, 453 planimetrically, 46 plankton, 661 plant species, 543 platform, 469 Plato, 533 Platonic solids, 87 Pliers, 435 Plücker, 300 Plücker’s conoid, 299 Poincaré, 530 Poinsot, 107 point at infinity, 23, 93, 221, 415 point of contact, 126 point of culmination, 2

point space, 35, 39 point-shaped light source, 199 polar, 34, 37 polar developable, 146 polar night, 479 polar plane, 35, 37, 41 polar winter, 156 polarity, 34, 39 polarization, 37 polarization at a circle, 130 polarization of a space curve, 37 pole, 34 polycarbonate, 215 polynomial function, 347, 355 Pompeii, 381 poster-size, 667 potato chips, 174 power, 16 Pozzo, 385, 386 precession motion, 474, 495 predatory fish, 548 preservation of affine ratios, 59 preservation of circles, 225 preservation of parallelity, 59 primary cell, 512 primary normal image, 285 primary perspective, 666 principal apex circle, 121 principal curvature, 279, 327, 328 principal line, 75 principal normal, 134 principal point, 368, 624, 626, 658 principal ray, 365, 625, 658 principal vanishing point, 368, 635, 670 principal view, 63, 67, 68, 70, 72, 107 principle of duality, 37 priority list, 98 prism, 93 problem of flight paths, 222 profile view, 67 projecting, 37 projection center, 57, 625 projection cone, 122, 199, 365, 386 projection curve, 303 projection plane, 54 projection ray, 54, 367 projection rays, 654 projective geometry, 5, 45 projective plane, 48 projector, 390 Proklus, 121 prolate ellipsoid, 236 propeller, 305 proportional angle of rotation, 313 proportionality, 302 prosthetic arm, 235 pumpkin, 268, 343 puppet, 465 puzzle, 531, 532 pyramid, 93 pyrite, 103 Pythagoras, 16, 152, 533

Q quadrangle grid, 354 quadrangulation, 359 quadratic cone, 47, 122, 234 quadratic surface, 234 quadratic transformation, 40 quadratrix, 682 quadratrix of Dinostratus, 682 quarter-torus, 280, 291 quasi-periodical, 525 quasi-periodical tilings, 522 quasi-periodicity, 524 quasicrystal, 525

696

R

rack and pinion gear, 457 radar corner reflector, 62 radar screen, 241 radial symmetry, 534 Radiata, 534 radio telescopes, 241 radius of curvature, 126, 129 rainbow, 398 rainbow colors, 215 rainbow effect, 404 range of points, 46 rapid prototyping, 355 rational Bézier curve, 352 rattle snake, 515 real-time, 99 receiver, 241 rectangular strip, 206 rectification, 677 rectifying developable, 134, 206, 207, 360 rectifying plane, 134 reef shark, 666 reflection, 12, 90, 512 reflection in a circle, 40 reflection in a perpendicular wall, 634 reflection in a sphere, 42 reflection point, 635 reflections in perspective, 633 reflex camera, 638, 639 refraction point, 401 refraction towards the normal, 401 refractive index, 403 regular dodecahedron, 527 Reichstag dome, 237 relative motion, 422, 444, 462 relative position, 68 relief perspective, 381 Renaissance, 53, 363, 380, 381 Renault, 351 reptiles, 401 repulsion, 141, 548 repulsive forces, 141 retina, 409 Reuleaux triangle, 442, 443 reverse ellipse motion, 444, 446 reverse engineering, 283, 285 reverse paper strip construction, 440, 441 revolution of a circle, 450 rhombic dodecahedron, 112–114, 528 rhombic icosahedron, 114 rhombic triacontahedron, 113 rhombus, 112, 518 rhumb line, 276, 288 rib vault, 550 ribs, 84 Ricardo Bofill Levi, 248 Riegler, 493, 498 Riemann, 49 right helical motion, 302 right helicoid, 298–300, 305, 307, 317 right side view, 67, 69 right-handed, 308, 315 ring cyclide, 287, 574, 575 ring sector, 219 ring torus, 574, 575 road construction, 203, 311 robber fly, 140 robot arm, 470 robotics, 438, 469 rod-shaped light source, 242 Rodler, 630, 631 rolling circle, 450 rolling shutter effect, 679 roof edge, 370 rose patch, 450 rotary table, 445 rotation, 88, 91, 512 rotation angle, 543 rotation component, 303 rotation-translation-step, 544

Index rotational surface, 42 rotoid, 556 rotor, 101 row of points, 250 rubber membrane, 326 Rubik, 88 rule, 54 Rule of Visibility, 96 ruled helical surface, 308–310 ruled surface, 294, 305, 355 ruler, 375

S

saddle point, 263 saddle surface, 140 Sagrada Família, 248, 670 sand dune, 203 sand tiger shark, 665 satellite dishes, 241 sawmill, 431 Sawyer, 499 scaffolding, 629 scale, 59, 471, 550 scaling, 552 scaling factor, 17, 552 scanner, 285, 681 scarab beetle, 509 Scarabaeidae, 509 scattering, 407 Scherk, 327 Scherk surface, 326 Schönbrunn, 166, 450 Schwarz minimal surface, 327 scientific capital, 9 scorpionfish, 663 screw axis, 305, 317 screw parameter, 302 screws, 84 scutoid, 521, 529 sea urchin, 284 seahorse, 553 seaweed, 201 secant, 16, 126, 133 secondary perspective, 666 sections, 84 seed, 543, 544 self-intersection, 182, 308, 361 self-rotation, 469 self-shadow boundary, 147, 162, 496 self-similarity, 522 semi-regular dodecahedron, 528 semi-regular pentagon, 526 semi-regular tiling, 520 semimajor axis, 77 series of points, 563 set of points, 37 set of tangents, 37 set square, 22, 417 shadow, 372, 623 shadow boundaries, 99, 162 shadow point, 478 shadow polygon, 99 shadow profile, 100 shark skin, 515, 555 Shechtman, 525 Sherlock Holmes, 60 shift lenses, 671 ship path, 222 shock wave, 549 side lighting, 632, 633, 635 side view, 70, 372, 378 sidelight, 371, 372 sign of the distance, 90 sine, 300 sine curve, 136, 167, 303, 324 sine law, 31 singular reaction, 548 skew, 72 skew axes, 468 skew axis, 246

697

Index skew generator quadrangle, 297 skew quadrangle, 244 skull, 376 slender moon crescent, 157 sling-jaw wrasse, 508 slope line, 321 slot guides, 447 small circle, 150 small stellated dodecahedron, 107 snail, 676 snail shell, 69 Snell’s window, 564 Snellius, 403 snow shovel, 306 soap bubble, 326 soccer ball, 109 solar day, 473 solar system, 472 solstice, 160, 495, 498–500 sonic strength, 537 sound box, 162 soundscapes, 240, 290 south, 478, 482, 483, 493, 496 south winter, 478 Southern Cross, 490 southern hemisphere, 481, 490 space, 52 space curve, 38, 341 space curve of degree four, 169 space of perception, 28, 29, 39 spatial affine transformation, 184 spatial cross, 166 spatial diagonal, 341 spatial imagination, 166, 622 spatial interpretation, 195 spatial Pythagoras, 152 species, 541 spectral color, 407, 408 specular point, 229 speed of growth, 302 sphere, 149, 234, 537 sphere cap, 278 sphere contour, 37, 365 sphere layer, 478 sphere model, 50 sphere packing, 110 sphere reflection, 42 sphere rhumb line, 277 spherical conic section, 32, 466 spherical cycloid, 461, 465 spherical generator image, 285 spherical kinematics, 180 spherical section, 150 spherical surface, 537 spherical tangent image, 285 spherical triangle, 51 Sphinx pattern, 522 spider’s eyes, 390 spikes, 346 spindle torus, 151, 152, 198, 278, 575 spine circle, 277 spine curve, 289 spiral developable, 318 spiral motion, 348 spiral right helicoid, 318 spiral surface, 286, 341 Spirobranchus giganteus, 567 splitting of hairs, 198 spotlight, 57 spout, 174 spy hopping, 565 square side, 517 square wheel, 192 square-grid fields, 390 St. Charles’ Church, 122 standard surfaces, 342 standpoint, 625 star, 46 star handle, 462 star polyhedra, 107

steel cable, 313 steering wheel, 129, 435 Steiner, 19 stellated dodecahedron, 107 step pyramid, 94 stepper, 437 stereographic projection, 219, 395, 492, 577, 578 stereoscopic image, 655 stereoscopic vision, 654 Stewart platform, 438, 469 stone pebbles, 7 stonefish, 663 straight line guidance, 433, 436 straight open ruled helical surfaces, 308 streamlining, 515 street, 59 string construction, 29 stroboscopic photos, 417 sub-net, 355 substitute construction, 36 sugary syrup, 539 summer solstice, 481 summer time, 493 sun collector, 242 sun foot, 372 sun gear, 455 sun point, 171, 372, 635 Sun’s culmination point, 484 sundial, 494 sunflower, 543, 544 sunlight, 483 sunrise, 370 super-wide-angle, 639 supernova, 547 supersphere, 239 supplementary angle, 19, 30, 33 surface, 537 surface degree, 354 surface metrics, 332 surface normal, 137, 285 surface of revolution, 32, 289, 341 surface of the Earth, 140 surface tangent, 260, 261 surface tension, 326, 538 swarm of fish, 548 swimming pool, 173, 312, 405 swordfish, 531 symmetry, 195, 534, 620 symmetry axes, 610, 630 symmetry plane, 135, 242, 285, 576, 643 synthetic proofs, 14 Syracuse, 7 system of axioms, 49 system of linear equations, 194

T

tacnode, 174 tactile sense, 391 tangent, 38, 126, 133 tangent distance, 16, 165 tangent of a curve, 126 tangent plane, 137, 150, 258, 285, 575 tangent surface, 134, 295, 309 tangential surface, 175, 206 tangerine, 217 tapetum lucidum, 391 tarantula, 391 tautochrone curve, 421 technical drawing, 84, 162 telescopic lens, 78, 658 television, 666 Temelin, 250 temporal hour, 493 tennis ball curve, 285 terminator, 81, 147, 157, 158 tessellation, 20, 519 Tetra Pak carton packages, 117 tetradecahedra, 110 tetrahedron, 105, 141 texture, 558

698 Thales, 9, 10, 31, 223, 447, 614 Thales circle, 18, 31, 375 Thales sphere, 152, 376 Thales’s theorem, 16 theorem of Brianchon, 193 theorem of intersecting lines, 8, 30, 656 theorem of Kawasaki, 116 theorem of right angles, 75, 77 thermal radiation, 239 Thompson problem, 141 thorn torus, 575 tiger, 552 tiger beetle, 508 tiling, 110, 522 Tokyo, 221 tomato, 343 tonal center, 558 tonal system, 556 tonic, 558 top view, 67, 373, 378, 484 topographic projection, 81 torsion, 135 torus, 167, 212, 272, 281, 470, 556 torus cap, 280 torus chain, 273 total internal reflection, 403, 407 totally differentiable, 338 tower clock, 494 trace point, 59, 369 train, 179 transcendental, 299 translation, 88, 302, 512 translation component, 303 translation surface, 242, 297 tree rings, 537 triacontahedron, 113 triads, 558 triangle, 7 triangulation, 360 triaxial ellipsoid, 236, 257 trihedron, 91 tripod, 90 trisectrix, 682 trisectrix of Hippias, 682 trochoid motion, 450 tropic, 478 true local time, 493 trunk, 519 Tunis, 221 turban eyes, 651 turbulence, 545 Tuscany, 426 two-bar linkage, 423 two-point guidance, 416 two-sheeted hyperboloid of revolution, 57, 246

U

ultra-wide-angle, 639, 665 umbilical points, 257 umbra shadow, 99, 103 umbrella, 327 unit cube, 613 unit points, 59 unit sphere, 612 upside down catenaries, 191

V

Vaduz, 210 vanishing plane, 55, 378 vanishing point, 55 Varadero, 159, 160 variety of shapes, 549 vector calculus, 152 Venus, 490 Vernes, 159 Verrazzano-Narrows Bridge, 191 vertex centroid, 13 vertex of the pencil, 39 vertical motion, 192

Index Vienna, 122, 159, 220, 237, 341, 473 viewing, 95 viewing angle, 658 viewing axis, 625 viewing cone, 368, 409 viewing pyramid, 368, 377 viewing rays, 653 Villarceau, 275, 276, 287 Villarceau circle, 277 virtual counterworld, 633 virus, 346 vise, 307 Vise-Grips, 434 vises, 307 visual appearance, 239 vitreous body, 366 Vogt, 64 volume centroid, 13 von Kempelen, 424 von Racknitz, 424, 425 Voronoi diagram, 205

W

waning moon, 157 Wankel engine, 452, 453 Wapiti, 349 wasp, 536, 552 water basin, 122 water droplets, 538 water slide, 312 water spider, 401 water strider, 401 water surface, 230, 397, 401, 404, 406, 407 waterproof, 117 wave peak, 7 wave structure of light, 403 wavefront, 239, 241, 404 waxing moon, 157 Weierstrass-℘-Function, 339 west, 160, 473, 482, 483, 499 wheel spoke, 62 whirligig beetle, 401 whispering bowls, 240 wide-angle lens, 394, 658, 659 Wieland, 498 willow branch, 540 winding point, 128 windmill, 208 wire, 327 wireframe model, 356 wobbler, 267 wolf spider, 391, 401 worm gears, 464 Wren, 246 Wunderlich, 217, 334

X

xyz-coordinates, 67

Y

year, 473 Yin and Yang, 11

Z

zenith, 157, 478, 479, 482, 493 zero circle, 189 zero meridian, 613 zero-dimensional, 6, 34 zone meridian, 498 zone time, 498 zoom-lens, 638