Advances in Microwave Engineering: From Novel Materials to Novel Microwave Applications (Modern Aspects of Computing, Devices, and Communication Engineering) [1 ed.] 103246898X, 9781032468983

Table of contents :
Cover
Half Title
Title
Copyright
Contents
Preface
Editors
Dedication
Contributors
1 Microstrip Antennas: Theory, Principles and Review of Literature
1.1 Introduction
1.2 Microstrip Patch Antenna Design
1.3 Feeding Techniques
1.4 Models of Analysis of Microstrip Antennas
1.5 Other Popular Analytical Models
1.6 Review of the Literature
1.6.1 Introduction
1.6.2 Mathematical Approaches in Antenna Design
1.6.3 Efforts in Resonant Frequency Determination
1.6.4 Bandwidth Enlargement Techniques
1.6.5 Monopole Antennas with Improved Frequency Response
1.6.6 Novel Feeding Techniques for Bandwidth Improvement
1.6.7 Coplanar Waveguide Technique for Bandwidth Improvement
1.6.8 Application of Fractal Geometries in Designing Antennas
1.6.9 Selection of a Suitable Substrate for Frequency Response Optimization
2 The Role of Microstrip Antennas in Microwave Engineering and Research
2.1 Introduction
2.2 Literature Survey
2.3 Antenna Design Formula
2.4 IE3D (Integral Equation Three-Dimensional) Software
2.4.1 HFSS Software (High-Frequency Structure Simulator)
2.5 Antenna Configuration
2.5.1 Patch Antenna with L-slot
2.5.2 Patch Antenna with T-slot
2.5.3 Patch Antenna with H-slot
2.5.4 Patch Antenna with U-slot
2.6 Conclusion
3 Recent Developments in Low-Cost Manufacturing Antennas and Their Challenges
3.1 Introduction
3.2 Low-Cost Antenna Manufacturing
3.3 Challenges in Low-Cost Antennas
3.4 Conclusion
4 Design and Performance Analysis of a Miniaturized UWB Monopole Antenna with Embedded Octagonal Slot and DGS for Various Wireless Applications
4.1 Introduction
4.2 Literature Survey
4.3 Antenna Design
4.4 Results and Discussions
4.5 Parametric Analysis
4.5.1 Impact of Different Ground Plane Lengths
4.5.2 Effect of the Substrate’s Various Thicknesses
4.5.3 Effects on the Ideal Ground of Various Ground Center Slot Shapes
4.5.4 Effect of the Different Substrate Type
4.6 Measurement and Fabrication
4.7 Conclusion
5 A Printed Array of Nature-Inspired Antennas for IoT and Future 5G Applications
5.1 Introduction
5.2 The Sole Radiator
5.2.1 Contour Length Computation
5.2.2 Analysis of Time-Domain Parameters
5.3 Proposed Array
5.3.1 Construction of the Feed Topology
5.3.2 Construction of Array Geometry
5.4 Results and Discussion
5.5 Conclusion
6 Optimization Algorithms for Reconfigurable Antenna Design: A Review
6.1 Introduction
6.2 Evolutionary Algorithms
6.2.1 Genetic Algorithm
6.2.2 Differential Evolution
6.2.3 Covariance Matrix Adaptation Evolution Strategy
6.3 Swarm Intelligence-Based Algorithm
6.3.1 Particle Swarm Optimization
6.3.2 Grey Wolf Optimizer
6.4 Conclusion
7 Review on Wearable Antennas for IoT, Healthcare, and High-End Applications
7.1 Introduction
7.2 Wearable Antenna Types
7.2.1 Traditional Wearable Designs
7.2.2 Textile Design Antenna
7.3 Creating and Designing of Wearable Antennas
7.3.1 Conductive Substance
7.3.2 Fabrication Method
7.4 Analysis Required for Wearable Antennas
7.4.1 SAR Modelling
7.4.2 Measurement with Different Bending
7.4.3 On-Body Measurements
7.4.4 Significance
7.5 Application of Wearable Antennas
7.5.1 Healthcare
7.5.2 Sports and Fitness
7.5.3 Internet of Things
7.6 Conclusion and Future Scope
8 A Review of Design Challenges of Metamaterial-Inspired Body-Worn Antennas
8.1 Introduction
8.2 Metamaterial-Inspired Dual Wideband Wearable Antenna for Wireless Applications
8.2.1 A Novel Wearable Metamaterial Fractal Antenna for Wireless Applications
8.2.2 Radiation Pattern Reconfigurable Wearable Antenna Based on Metamaterial Structure
8.2.3 Compact All-Textile, Dual-Band Antenna Loaded with Metamaterial-Inspired Structure
8.2.4 A Compact Triple-Band Metamaterial-Inspired Antenna for Wearable Applications
8.2.5 Metamaterial-Embedded Wearable Rectangular
Microstrip-Patch Antenna
8.2.6 Metasurface-Enabled Hepta-Band Compact Antenna for Wearable Applications
8.2.7 An Ultra-Wideband, Low-SAR, Flexible, Metasurface-Enabled Antenna for WBAN Applications
8.3 Summary
9 An Efficient Wearable Antenna Deploying Different Geometry for Wireless Capsule Endoscopy
9.1 Introduction
9.2 Capsule Antenna Design
9.2.1 Working Principle
9.2.2 Effects of the Slot on the Antenna
9.3 Wearable Antenna Design
9.4 Simulation Results
9.5 Design Challenges
9.6 Conclusion
10 Wearable MIMO Antenna with High Port Isolation for e-Health Monitoring Applications
10.1 Introduction
10.2 Architecture and Design of Antenna
10.3 Discussion of Results
10.4 Discussion of MIMO Parameters of the Final
Antenna
10.5 Conclusion
11 Development of Multiport MIMO Antenna for C-Band Frequency Application in Wireless Communication
11.1 Introduction
11.2 Structural Layout of Proposed Antenna
11.3 Geometry of Two-Port MIMO Antenna
11.4 Results and Discussion of Proposed MIMO Antenna
11.4.1 S11 (dB) and S12 (dB)
11.4.2 Distribution of Surface Current (A/m) for the Proposed MIMO Antenna
11.4.3 Gain (Measured in dBi) and Efficiency (Measured in Percent) in Relation to Frequency (GHz)
11.5 Conclusion
12 Harmonic Suppression Triple-Band U-Slot Antenna for GPS/WLAN/5G Applications
12.1 Introduction
12.2 Antenna Design and Analysis
12.2.1 Antenna Configuration
12.2.2 Design and Analysis of Resonance Frequencies
12.2.3 Parametric Study of Patch and Slot Dimensions
12.3 Results and Discussion
12.4 Conclusion
13 Mutual Coupling Reduction in a Patch Antenna Array Using a Microstrip Resonator for Wireless Communication System Applications
13.1 Introduction
13.2 Antenna Design and Its Configuration
13.3 Simulation and Measurement Results
13.4 Conclusion
14 Filter Synthesis–Based Compact Dual-Band Filtenna for C-Band Applications
14.1 Introduction
14.2 Filter Synthesis
14.3 Filtenna Design
14.4 Results and Discussion
14.5 Conclusion
15 Reviews on Electromagnetic Interference/Compatibilities
15.1 Introduction
15.1.1 Fundamentals of EMI
15.1.2 What Causes Electromagnetic Interference?
15.2 Types of Electromagnetic Interference
15.2.1 Manmade EMI
15.2.2 Natural EMI
15.2.3 Narrowband EMI
15.2.4 Broadband EMI
15.2.5 Radiated EMI
15.2.6 Conducted EMI
15.2.7 Coupled EMI
15.3 Elimination Methods of EMI
15.3.1 Shielding
15.3.2 Filtering
15.3.3 Ground
15.3.4 Transmission Mode
15.4 Measuring Methods for EMI
15.4.1 Emission Testing
15.4.2 Radiated Emission Testing
15.4.3 Conducted Emission Testing
15.4.4 Immunity Testing
15.5 Conclusion
16 Application of a Frequency Selective Surface in the Modern Medical Field
16.1 Introduction
16.2 Theoretical Perspective: How Does FSS Transmit or Block Incoming Waves?
16.3 Simulation and Measurement
16.4 Significance of FSS on Antennas
16.5 Application of FSS in the Medical Field
16.5.1 Enhancing the Performance of the ISM Antenna
16.5.2 EM Absorber
16.5.3 FSS for Biomedical Sensing
16.5.4 Dosimeter Tag
16.5.5 Wearable Medical Devices
16.5.6 Mobile Body Area Network
16.5.7 MRI
16.5.8 Concentrating EM Energy into Target
Tissue
16.6 Future Improvements
16.7 Conclusion
17 Scattering Matrices and Their Applications in Microwave
Engineering
17.1 Introduction
17.2 Quantifying and Analyzing the Input Signal and Power Flow
17.3 Origin of Scattering Parameters from the Transmission Line
17.4 Terms Related to Any Network
17.5 S-Matrix Determined from Z- and Y-Matrix
17.6 Properties of S-Parameters
17.7 Scattering Matrices of Microwave Components
17.8 Measurement of Scattering Parameters
17.9 Signal Flow Graph
17.9.1 The Flow Graph Representation for Different Conditions
17.10 Conclusions
18 A Feasibility Study for Biomedical Applications via Microwave Imaging
18.1 Introduction
18.2 Dielectric Properties of Human Tissues
18.3 Design and Analysis of Antenna Performance
18.3.1 Antenna Design
18.3.2 Performance of Antenna
18.4 Conclusion
19 Review of Current Advancements in Microwave UWB Filter
19.1 Introduction
19.2 UWB Technology
19.3 Advantages
19.4 Disadvantages
19.5 Applications
19.6 UWB Filter
19.7 Performance Analysis of UWB Filters
19.8 Different Techniques to Develop UWB Filters
19.9 Review of Previous Works in UWB Filters
19.10 UWB Filter Cascading a Low-Pass and High-Pass Filter
19.11 MMR for Designing a UWB Filter with Multiple Notches
19.12 Ring Resonator with Quad T Stub-Loaded Structure
19.13 Square Ring Resonator with Extended Stop Band
19.14 UWB Filter Implementing a Defected Ground Structure
19.15 A Triple-Notched Band UWB Filter
19.16 Conclusion and Future Scope
20 Design of Broadband Planar Couplers Using an Existing Filter Design Approach
20.1 Introduction
20.2 Operation Principle of Forward-Wave Directional Coupler
20.3 Basics of Asymmetrical Directional Couplers
20.4 Design of a Forward-Wave Directional Coupler Using MMR
20.4.1 Design Equations of Asymmetric Coupled Sections
20.4.2 10 dB Forward-Wave Directional Coupler Using MMR
20.5 MMR-Based Broadband Six-Port Coupler
20.6 Conclusion
21 Sensing of Trapped Survivors Using IR-UWB Radar
21.1 Introduction
21.2 Motivation
21.3 Current Technologies Used
21.4 Importance of Radar
21.5 Radar-Rubble-Target Model
21.5.1 Different Types of UWB Radar
21.5.2 Detailed Description of Rubble
21.5.3 Human Target Model
21.6 Human Vital Signs Mathematical Model
21.7 Methodology
21.7.1 Raw Data Preprocessing Stage
21.8 Buried Human Location and Vital Signs Estimation Stage
21.9 Experimental Setup
21.10 Artificial Breathing Simulator
21.11 Live Human Subjects
21.11.1 No Obstruction between Radar and
Target
21.11.2 Planar-Wall Obstruction between Radar
and Target
21.11.3 Complex Rubble Obstruction between
Radar and Target
21.12 Results and Discussion
21.12.1 Estimation of Breathing Simulator Frequency
21.13 Estimation of Human Target Location and Vital Signs
21.13.1 Single Human Target Per Range
21.14 Multiple Targets Per Range
21.15 Correlation Analysis
21.15.1 Single-Target Range Error
21.15.2 Multitarget Range Error
21.15.3 Target Heartbeat Signal Accuracy
21.15.4 Target Breathing Signal Accuracy
21.16 Conclusion
22 Employment of Antennas in Biomedical Applications: A Review
22.1 Introduction
22.2 Design Requirements of Bio-implantable Antennas
22.3 Concept Behind Usage of Bio-implantable Antennas for Tumour Detection
22.4 Conclusion
Index

Citation preview

Advances in

Microwave

Engineering

This text showcases recent advancements in the field of microwave engineering, starting from the use of innovative materials to the latest microwave applications. It also highlights safety guidelines for exposure to microwave and radio frequency energy. The book provides information on measuring circuit parameters and dielectric parameters. • Explains microwave antennas, microwave communication, microwave propagation, microwave devices, and circuits in detail • Covers microwave measurement techniques, radiation hazards, space communication, and safety measures • Focuses on advanced computing technologies, wireless communication, and fiber optics • Presents scattering matrix and microwave passive components and devices such as phase shifters and power dividers • Showcases the importance of space communication, radio astronomy, microwave material processing, and advanced computing technologies The text provides a comprehensive study of the foundations of microwave heating and its interactions with materials for various applications. It also addresses applications of microwave devices and technologies in diverse areas, including computational electromagnetics, remote sensing, transmission lines, radiation hazards, and safety measures. It emphasizes the impact of resonances on microwave power absorption and the effect of nonuniformity on heating rates. The text is primarily written for senior undergraduate students, graduate students, and academic researchers in the fields of electrical engineering, electronics and communication engineering, computer engineering, and materials science.

Modern Aspects of Computing, Devices, and Communication Engineering Ankan Bhattacharya Advances in Microwave Engineering: From Novel Materials to Novel Microwave Applications Ankan Bhattacharya, Bappadittya Roy, Arnab De, Ujjal Chakraborty and Anup Kumar Bhattacharjee

Advances in

Microwave

Engineering

From Novel Materials to Novel

Microwave Applications

Edited by

Ankan Bhattacharya, Bappadittya Roy,

Arnab De, Ujjal Chakraborty and

Anup Kumar Bhattacharjee

First edition published 2024 by CRC Press 6000 Broken Sound Parkway NW, Suite 300, Boca Raton, FL 33487–2742 and by CRC Press 4 Park Square, Milton Park, Abingdon, Oxon, OX14 4RN CRC Press is an imprint of Taylor & Francis Group, LLC © 2024 selection and editorial matter, Ankan Bhattacharya, Bappadittya Roy, Arnab De, Ujjal Chakraborty and Anup Kumar Bhattacharjee, individual chapters, Reasonable efforts have been made to publish reliable data and information, but the author and publisher cannot assume responsibility for the validity of all materials or the consequences of their use. The authors and publishers have attempted to trace the copyright holders of all material reproduced in this publication and apologize to copyright holders if permission to publish in this form has not been obtained. If any copyright material has not been acknowledged please write and let us know so we may rectify in any future reprint. Except as permitted under U.S. Copyright Law, no part of this book may be reprinted, reproduced, transmitted, or utilized in any form by any electronic, mechanical, or other means, now known or hereafter invented, including photocopying, microfilming, and recording, or in any information storage or retrieval system, without written permission from the publishers. For permission to photocopy or use material electronically from this work, access www.copyright.com or contact the Copyright Clearance Center, Inc. (CCC), 222 Rosewood Drive, Danvers, MA 01923, 978–750–8400. For works that are not available on CCC please contact mpkbookspermissions@ tandf.co.uk Trademark notice: Product or corporate names may be trademarks or registered trademarks and are used only for identification and explanation without intent to infringe. ISBN: 978-1-032-46898-3 (hbk) ISBN: 978-1-032-60610-1 (pbk) ISBN: 978-1-003-45988-0 (ebk) DOI: 10.1201/9781003459880 Typeset in Sabon by Apex CoVantage, LLC

Contents

Preface Editors Contributors 1 Microstrip Antennas: Theory, Principles and Review of

Literature

xvii

xix

xxv

1

A N K A N B H AT TACH ARYA

1.1 1.2 1.3 1.4 1.5 1.6

Introduction 1

Microstrip Patch Antenna Design 2

Feeding Techniques 3

Models of Analysis of Microstrip Antennas 3

Other Popular Analytical Models 7

Review of the Literature 7

1.6.1 Introduction 7

1.6.2 Mathematical Approaches in Antenna Design 8

1.6.3 Efforts in Resonant Frequency Determination 8

1.6.4 Bandwidth Enlargement Techniques 8

1.6.5 Monopole Antennas with Improved Frequency

Response 9

1.6.6 Novel Feeding Techniques for Bandwidth

Improvement 10

1.6.7 Coplanar Waveguide Technique for Bandwidth

Improvement 10

1.6.8 Application of Fractal Geometries in Designing

Antennas 11

1.6.9 Selection of a Suitable Substrate for Frequency

Response Optimization 11

v

vi

Contents

2 The Role of Microstrip Antennas in Microwave

Engineering and Research

18

BA RU N M A Z UMDAR AN D ASH I S DE

2.1 2.2 2.3 2.4

Introduction 18

Literature Survey 18

Antenna Design Formula 19

IE3D (Integral Equation Three-Dimensional)

Software 20

2.4.1 HFSS Software (High-Frequency Structure

Simulator) 21

2.5 Antenna Configuration 21

2.5.1 Patch Antenna with L-slot 21

2.5.2 Patch Antenna with T-slot 23

2.5.3 Patch Antenna with H-slot 26

2.5.4 Patch Antenna with U-slot 27

2.6 Conclusion 29

3 Recent Developments in Low-Cost Manufacturing

Antennas and Their Challenges

32

S . K A N NA D H A SAN , R. NAGARAJAN , C . JI SH A C HA NDR A , A ND G . S R I V I D H YA

3.1 3.2 3.3 3.4

Introduction 32

Low-Cost Antenna Manufacturing 36

Challenges in Low-Cost Antennas 39

Conclusion 42

4 Design and Performance Analysis of a Miniaturized

UWB Monopole Antenna with Embedded Octagonal

Slot and DGS for Various Wireless Applications

45

A PA R NA PA NJA, ARNAB DE , KOYN DRI K BH AT TAC HA R JEE, PA RT HA PR AT IM S A R K A R , A N D AN UP KUMAR BH ATTACH ARJEE

4.1 4.2 4.3 4.4 4.5

Introduction 45

Literature Survey 47

Antenna Design 50

Results and Discussions 53

Parametric Analysis 59

Contents

4.5.1 Impact of Different Ground Plane Lengths 4.5.2 Effect of the Substrate’s Various Thicknesses

vii

59

60

4.5.3 Effects on the Ideal Ground of Various Ground

Center Slot Shapes 60

4.5.4 Effect of the Different Substrate Type 61

4.6 Measurement and Fabrication 62

4.7 Conclusion

64

5 A Printed Array of Nature-Inspired Antennas for IoT

and Future 5G Applications

70

K A LYA N S U N DAR KO L A AN D AN I RBAN CH ATT ER JEE

5.1 Introduction 70

5.2 The Sole Radiator

72

5.2.1 Contour Length Computation 74

5.2.2 Analysis of Time-Domain Parameters 5.3 Proposed Array

76

5.3.1 Construction of the Feed Topology 5.3.2 Construction of Array Geometry 5.4 Results and Discussion 5.5 Conclusion

75

76

77

79

82

6 Optimization Algorithms for Reconfigurable Antenna

Design: A Review K . K A RT H I K A , K. AN USH A, K. KAVI TH A, AN D D. MOHA NA GEET HA

6.1 Introduction 85

6.2 Evolutionary Algorithms

87

6.2.1 Genetic Algorithm 87

6.2.2 Differential Evolution 89

6.2.3 Covariance Matrix Adaptation Evolution

Strategy 91

6.3 Swarm Intelligence-Based Algorithm 6.3.1 Particle Swarm Optimization 6.3.2 Grey Wolf Optimizer 95

6.4 Conclusion

101

92

92

85

viii

Contents

7 Review on Wearable Antennas for IoT, Healthcare, and

High-End Applications

104

VA I B H AV S A I NI , P RAF UL RAN JAN , AN D AYUSHI JA IN

7.1 Introduction 104

7.2 Wearable Antenna Types 104

7.2.1 Traditional Wearable Designs 104

7.2.2 Textile Design Antenna 106

7.3 Creating and Designing of Wearable Antennas 106

7.3.1 Conductive Substance 106

7.3.2 Fabrication Method 107

7.4 Analysis Required for Wearable Antennas 107

7.4.1 SAR Modelling 107

7.4.2 Measurement with Different Bending 108

7.4.3 On-Body Measurements 108

7.4.4 Significance 108

7.5 Application of Wearable Antennas 108

7.5.1 Healthcare 108

7.5.2 Sports and Fitness 109

7.5.3 Internet of Things 110

7.6 Conclusion and Future Scope 112

8 A Review of Design Challenges of Metamaterial-Inspired

Body-Worn Antennas 115

M O U M I TA B OSE , APARNA KUN DU, ABH I SH E K SA R K HEL, A ND UJJA L C H A K R A B O RTY

8.1 Introduction 115

8.2 Metamaterial-Inspired Dual Wideband Wearable

Antenna for Wireless Applications 116

8.2.1 A Novel Wearable Metamaterial Fractal Antenna

for Wireless Applications 120

8.2.2 Radiation Pattern Reconfigurable Wearable

Antenna Based on Metamaterial Structure 124

8.2.3 Compact All-Textile, Dual-Band Antenna

Loaded with Metamaterial-Inspired

Structure 125

8.2.4 A Compact Triple-Band Metamaterial-Inspired

Antenna for Wearable Applications 128

Contents

ix

8.2.5 Metamaterial-Embedded Wearable Rectangular

Microstrip-Patch Antenna 132

8.2.6 Metasurface-Enabled Hepta-Band Compact

Antenna for Wearable Applications 133

8.2.7 An Ultra-Wideband, Low-SAR, Flexible,

Metasurface-Enabled Antenna for WBAN

Applications 135

8.3 Summary 137

9 An Efficient Wearable Antenna Deploying Different

Geometry for Wireless Capsule Endoscopy

145

VA N I T H A R A N I RE N TAPAL L I AN D BAP PADI TTYA ROY

9.1 Introduction 145

9.2 Capsule Antenna Design 147

9.2.1 Working Principle 149

9.2.2 Effects of the Slot on the Antenna 150

9.3 Wearable Antenna Design 150

9.4 Simulation Results 153

9.5 Design Challenges 156

9.6 Conclusion 157

10 Wearable MIMO Antenna with High Port Isolation

for e-Health Monitoring Applications

164

A S H I M K U M A R BI SWAS, KO USH I K ROY, VI CKY K UMA R , B ISWA RUP N E O G I , A N D UJJAL CH AKRABO RTY

10.1 10.2 10.3 10.4

Introduction 164

Architecture and Design of Antenna 166

Discussion of Results 167

Discussion of MIMO Parameters of the Final

Antenna 169

10.5 Conclusion 172

11 Development of Multiport MIMO Antenna for C-Band

Frequency Application in Wireless Communication K R A N T I D. PATI L AN D D.M. YADAV

11.1 Introduction 175

11.2 Structural Layout of Proposed Antenna 177

11.3 Geometry of Two-Port MIMO Antenna 178

175

x

Contents

11.4 Results and Discussion of Proposed MIMO

Antenna 180

11.4.1 S11 (dB) and S12 (dB) 180

11.4.2 Distribution of Surface Current (A/m) for the

Proposed MIMO Antenna 181

11.4.3 Gain (Measured in dBi) and Efficiency

(Measured in Percent) in Relation to

Frequency (GHz) 182

11.5 Conclusion 183

12 Harmonic Suppression Triple-Band U-Slot Antenna

for GPS/WLAN/5G Applications

185

J. R A J E S H WA R GO UD, N . V. KOTE SWARA RAO, A ND A . MA LLIK A R JUNA PRASAD

12.1 Introduction 185

12.2 Antenna Design and Analysis 186

12.2.1 Antenna Configuration 186

12.2.2 Design and Analysis of Resonance

Frequencies 191

12.2.3 Parametric Study of Patch and Slot

Dimensions 193

12.3 Results and Discussion 195

12.4 Conclusion 197

13 Mutual Coupling Reduction in a Patch Antenna Array

Using a Microstrip Resonator for Wireless Communication

System Applications 201

S A N T I M OY MAN DAL AN D CH AN DAN KUMAR GHOSH

13.1 13.2 13.3 13.4

Introduction 201

Antenna Design and Its Configuration 204

Simulation and Measurement Results 205

Conclusion 207

14 Filter Synthesis–Based Compact Dual-Band Filtenna

for C-Band Applications

213

P R AV E S H PA L , RASH MI SI N H A, RAN JE E T KUMA R , PR AV EEN K UMA R , A ND S A N TO S H K UMAR MAH TO

14.1 Introduction

213

Contents

14.2 14.3 14.4 14.5

Filter Synthesis 214

Filtenna Design 217

Results and Discussion Conclusion 224

xi

220

15 Reviews on Electromagnetic Interference/Compatibilities

226

H I M A D R I S E KH AR DAS, SAN TAN U MI SH RA, GOUR ISA NK A R ROY M A H A PAT R A , AN D TAKASH I RO AKI TSU

15.1 Introduction 226

15.1.1 Fundamentals of EMI 227

15.1.2 What Causes Electromagnetic

Interference? 228

15.2 Types of Electromagnetic Interference 228

15.2.1 Manmade EMI 228

15.2.2 Natural EMI 229

15.2.3 Narrowband EMI 229

15.2.4 Broadband EMI 229

15.2.5 Radiated EMI 230

15.2.6 Conducted EMI 230

15.2.7 Coupled EMI 231

15.3 Elimination Methods of EMI 232

15.3.1 Shielding 233

15.3.2 Filtering 235

15.3.3 Ground 235

15.3.4 Transmission Mode 235

15.4 Measuring Methods for EMI 239

15.4.1 Emission Testing 240

15.4.2 Radiated Emission Testing 240

15.4.3 Conducted Emission Testing 240

15.4.4 Immunity Testing 241

15.5 Conclusion 242

16 Application of a Frequency Selective Surface in the

Modern Medical Field M . S H O BA NA AN D S. RAGH AVAN

16.1 Introduction

245

245

xii

Contents

16.2 Theoretical Perspective: How Does FSS Transmit or

Block Incoming Waves? 246

16.3 Simulation and Measurement 249

16.4 Significance of FSS on Antennas 249

16.5 Application of FSS in the Medical Field 249

16.5.1 Enhancing the Performance of the ISM

Antenna 249

16.5.2 EM Absorber 251

16.5.3 FSS for Biomedical Sensing 251

16.5.4 Dosimeter Tag 253

16.5.5 Wearable Medical Devices 256

16.5.6 Mobile Body Area Network 256

16.5.7 MRI 257

16.5.8 Concentrating EM Energy into Target

Tissue 259

16.6 Future Improvements 261

16.7 Conclusion 261

17 Scattering Matrices and Their Applications in Microwave

Engineering S H I P R A B H ATI A AN D MAN O J SARKAR

17.1 Introduction 266

17.2 Quantifying and Analyzing the Input Signal and

Power Flow 267

17.3 Origin of Scattering Parameters from the Transmission

Line 269

17.4 Terms Related to Any Network 270

17.5 S-Matrix Determined from Z- and Y-Matrix 271

17.6 Properties of S-Parameters 272

17.7 Scattering Matrices of Microwave Components 274

17.8 Measurement of Scattering Parameters 277

17.9 Signal Flow Graph 278

17.9.1 The Flow Graph Representation for Different

Conditions 283

17.10 Conclusions 284

266

Contents

18 A Feasibility Study for Biomedical Applications via

Microwave Imaging

xiii

287

S W E E T Y JA I N

18.1 Introduction 287

18.2 Dielectric Properties of Human Tissues 288

18.3 Design and Analysis of Antenna Performance 289

18.3.1 Antenna Design 289

18.3.2 Performance of Antenna 290

18.4 Conclusion 293

19 Review of Current Advancements in Microwave

UWB Filter PA RT H A P ROTI M KAL I TA, AKASH BURAGO H AIN, YAT ISH B E R I A , A N D GO URE E SH AN KAR DAS

19.1 Introduction 297

19.2 UWB Technology 298

19.3 Advantages 298

19.4 Disadvantages 299

19.5 Applications 299

19.6 UWB Filter 300

19.7 Performance Analysis of UWB Filters 301

19.8 Different Techniques to Develop UWB Filters 302

19.9 Review of Previous Works in UWB Filters 304

19.10 UWB Filter Cascading a Low-Pass and High-Pass

Filter 305

19.11 MMR for Designing a UWB Filter with Multiple

Notches 307

19.12 Ring Resonator with Quad T Stub-Loaded

Structure 308

19.13 Square Ring Resonator with Extended Stop

Band 308

19.14 UWB Filter Implementing a Defected Ground

Structure 309

19.15 A Triple-Notched Band UWB Filter 310

19.16 Conclusion and Future Scope 311

297

xiv

Contents

20 Design of Broadband Planar Couplers Using an

Existing Filter Design Approach

316

P R AT I K M O N DAL , AN UMOY GH O SH , AN D TAPA N MA NDA L

20.1 Introduction 316

20.2 Operation Principle of Forward-Wave Directional

Coupler 318

20.3 Basics of Asymmetrical Directional Couplers 320

20.4 Design of a Forward-Wave Directional Coupler Using

MMR 320

20.4.1 Design Equations of Asymmetric Coupled

Sections 321

20.4.2 10 dB Forward-Wave Directional Coupler

Using MMR 326

20.5 MMR-Based Broadband Six-Port Coupler 331

20.6 Conclusion 336

21 Sensing of Trapped Survivors Using IR-UWB Radar A M I T S A R K A R AN D DE BAL I NA GH O SH

21.1 21.2 21.3 21.4 21.5

Introduction 339

Motivation 340

Current Technologies Used 341

Importance of Radar 341

Radar-Rubble-Target Model 342

21.5.1 Different Types of UWB Radar 342

21.5.2 Detailed Description of Rubble 343

21.5.3 Human Target Model 344

21.6 Human Vital Signs Mathematical Model 344

21.7 Methodology 346

21.7.1 Raw Data Preprocessing Stage 346

21.8 Buried Human Location and Vital Signs Estimation

Stage 347

21.9 Experimental Setup 347

21.10 Artificial Breathing Simulator 349

21.11 Live Human Subjects 350

21.11.1 No Obstruction between Radar and

Target 350

339

Contents

21.12

21.13

21.14 21.15

21.16

xv

21.11.2 Planar-Wall Obstruction between Radar

and Target 351

21.11.3 Complex Rubble Obstruction between

Radar and Target 352

Results and Discussion 354

21.12.1 Estimation of Breathing Simulator

Frequency 354

Estimation of Human Target Location and Vital

Signs 355

21.13.1 Single Human Target Per Range 355

Multiple Targets Per Range 356

Correlation Analysis 358

21.15.1 Single-Target Range Error 358

21.15.2 Multitarget Range Error 358

21.15.3 Target Heartbeat Signal Accuracy 359

21.15.4 Target Breathing Signal Accuracy 360

Conclusion 360

22 Employment of Antennas in Biomedical Applications:

A Review

365

K R I S H A N U K UN DU AN D NARE N DRA NATH PAT HA K

22.1 Introduction 365

22.2 Design Requirements of Bio-implantable

Antennas 367

22.3 Concept Behind Usage of Bio-implantable Antennas

for Tumour Detection 368

22.4 Conclusion 370

Index

375

Preface

This book focuses on the recent technological breakthroughs in microwave engineering, including novel materials and novel microwave applications. Microwave engineering and associated technologies will be examined for emerging innovations and cutting-edge research. Microwave engineer­ ing encompasses new breakthroughs and novel techniques in microwave antenna design as well as many elements of microwave propagation. Start­ ing with single/multiband antennas, this book will demonstrate many design and performance features of wideband to super-wideband antennas, as well as multiple input/multiple outputs (MIMOs) for wireless communication, as well as various gadgets for portable wireless devices. Reviews and research studies on microwave antennas, microwave com­ munication, microwave devices and circuits, microwave propagation, elec­ tromagnetic interference/electromagnetic capability (EMI/EMC), radar technologies, computational electromagnetics, remote sensing, microwave measurements, microwave radiation hazards and safety measures, micro­ wave transmission lines, space communication, radio astronomy, microwave material processing, microwave imaging, advanced computing technologies, wireless communication, microwave and fiber optics, etc., are proposed to be included in this book. The goal of this book is to highlight various areas of microwave com­ munication and networking in addition to highlight reviews and research on cutting-edge technologies by academicians, researchers, and scientists in the fields of microwave engineering and allied areas.

xvii

Editors

Ankan Bhattacharya earned BTech and MTech degrees in Electronics and Communication Engineering from West Bengal University of Technology, Kolkata, India. He completed his PhD at the National Institute of Technology, Durgapur, India. He is the author of several research papers which have been published in many reputed journals and conferences at the national and international levels. Dr. Bhattacharya is a life member of the Forum of Scientists, Engineers  & Technologists (FOSET), a member of the Institution of Engineers India (IEI), and a member of the International Association of Engineers (IAENG). His areas of research are antenna engineering, computational electromagnetics, electronic circuits and systems, signal processing, microwave devices, and wireless communication technologies. He is also an editor or reviewer of many national and international journals of repute. He has organized and participated in many national and international conferences, seminars, workshops and webinars. Dr. Bhattacharya has been active in delivering invited talks and has also been a part of many national and international conferences in the capacity of coordinator, session chair, technical committee member, etc. Dr. Bhattacharya has been appointed as a guest editor of SN Applied Sciences, a multidisciplinary, peer-reviewed journal of Springer Nature (indexed in Scopus). He has also been inducted into the editorial board of the Circuits and Systems journal from Scientific Research Publishing (SCIRP). Dr. Bhattacharya has been appointed as an associate editor of the Journal of Information Processing Systems (JIPS), an official international journal of the Korea Information Processing Society (indexed in Scopus and ESCI). Presently he is associated with Hooghly Engineering & Technology College (HETC), Hooghly, India as an Associate Professor and Head of the Electronics and Communications Engineering Department.

xix

xx

Editors

Bappadittya Roy earned his PhD degree in electronics and communication engineering from the National Institute of Technology, Durgapur, India. He is presently associated with the Vellore Institute of Technology-AP University, Amaravati, India, as an associate professor of the School of Electronics Engineering. He is a senior member of IEEE and SLATE 2023 member from IEEE Hyderabad Section. His research areas are Millimeter Wave, Fractal Antennas, MIMO, Compact antenna for Mobile Communication and Biomedical applications. He has several indexed publications including articles in reputed journals, conferences, book chapters and books. Also, be involved in a few reputed international conferences and seminars as an organizing committee member. He has shared his experience as a Guest Editor of UGC CARE Journal, Publicity chair for IECC 2023, Osaka Japan, and Conference Chair of a series of IEEE International Conferences AISP22, AISP 23. Dr. Roy has been active in delivering invited talks and has also been a part of many national and international conferences in the capacity of coordinator, session chair, technical committee member, etc. He has received many national and international travel grants from Govt. of India and has traveled abroad for seminars, conferences and workshops. Dr. Roy received Best Research Publication (E&T), Publication Award and Raman Research awards from VIT-AP University in 2020,2021 and 2022. Dr.Roy always welcomes researchers and faculties to work in collaboration in the fields of Wireless communication and Antenna Technology. Arnab De earned his BTech and MTech in Electronics and Communication Engineering from West Bengal University of Technology,West Bengal, India, in 2012 and 2014, respectively. He completed his PhD in Electronics and Communication Engineering in November  2021 from the National Institute of Technology, Durgapur, India, and is a member of the Institute of Electrical and Electronics Engineers (IEEE), a life member of International Association of Engineers (IAENG), a life member of Forum of Scientists, Engineers and Technologists (FOSET), and an associate member of Institution of Engineers, India (IEI). He is currently working as an Assistant Professor in the Department of Advanced Computer Science Engineering under School of Computing and Informatics at Vignan's Foundation of Science, Technology and Research, Vadlamudi, Andhra Pradesh, India since March, 2023. He has also travelled abroad for international conferences and seminars. He is an active reviewer of many journals and conferences of high repute. He has participated in numerous National/International Conferences, Seminars, Workshops and Webinars. He has also organized various Workshops and Seminars. He has also been an

Editors

xxi

active member as well as Technical Committee Member of various workshops and conferences. His current research areas include compact Microstrip slotted antennas, Reconfigurable antennas, Defected Ground structures (DGS), Array Antenna, UWB and SWB communication, 5G, MIMO etc. To his credit, he has many reputed journals and conference publications in the fields of antenna engineering and wireless communications. Ujjal Chakraborty is affiliated with the Department of Electronics and Communication Engineering, National Institute of Technology, Silchar. He is currently providing services as an assistant professor. He has authored and co-authored multiple peerreviewed scientific papers and presented works at many national and international conferences. His contributions have garnered recognition from honorable subject experts around the world. He is actively associated with different societies and academies. His academic career is decorated with several reputed awards and funding. His research interests include compact multiband antennas, phased array antennas, bodywearable conformal antennas, and reconfigurable antennas. Anup Kumar Bhattacharjee earned his BE degree in Electronics and Telecommunication Engineering from B.E. College, Shibpur (presently the Indian Institute of Engineering Science and Technology, Shibpur), Howrah, India, in 1983. He earned his ME and PhD degrees from Jadavpur University, Kolkata, India, in 1985 and 1989, respectively. Presently he is associated with the National Institute of Technology, Durgapur, West Bengal, India, as a senior professor with the Electronics and Communication Engineering Department. His research areas are electronic devices and circuits, microwave devices, microstrip antennas, embedded systems, VLSI systems, mobile communications, satellite communications, etc. He has successfully supervised or co-supervised 25 PhD students and has published over 150 articles in national and international journals, books, and conferences.

Dr. Ankan Bhattacharya dedicates this book to the loving memory of his father, the late Amit Kumar Bhattacharya

xxiii

Contributors

Takashiro Akitsu Tokyo University of Science Tokyo, Japan K. Anusha Kumaraguru College of Technology Coimbatore, Tamil Nadu, India Yatish Beria Dibrugarh University Dibrugarh, Assam, India Shipra Bhatia CSIR-CEERI Pilani Rajasthan, India Anup Kumar Bhattacharjee National Institute of Technology Durgapur Durgapur, West Bengal, India

Moumita Bose National Institute of Technology Silchar Silchar, Assam, India Akash Buragohain Dibrugarh University Dibrugarh, Assam, India Ujjal Chakraborty National Institute of Technology Silchar Silchar, Assam, India C. Jisha Chandra Gnanamani College of Technology Namakkal, Tamilnadu, India Anirban Chatterjee National Institute of Technology Goa Ponda, Goa, India

Koyndrik Bhattacharjee Dr. B. C Roy Engineering College Durgapur, West Bengal, India

Himadri Sekhar Das Haldia Institute of Technology Haldia, West Bengal, India

Ankan Bhattacharya Hooghly Engineering & Technology College Hooghly, West Bengal, India

Gouree Shankar Das Dibrugarh University Dibrugarh, Assam, India

Ashim Kumar Biswas JIS College of Engineering Kalyani, West Bengal, India

Arnab De Vignan’s Foundation for Science, Technology, and Research Guntur, Andhra Pradesh, India xxv

xxvi

Contributors

Ashis De Gargi Memorial Institute of Technology Kolkata, West Bengal, India D. Mohana Geetha Sri Krishna College of Engineering and Technology Coimbatore, Tamil Nadu, India Anumoy Ghosh National Institute of Technology Mizoram Aizawl, Mizoram, India Chandan Kumar Ghosh Dr. B. C. Roy Engineering College Durgapur, West Bengal, India Debalina Ghosh Indian Institute of Technology Bhubaneswar Bhubaneswar, Odisha, India J. Rajeshwar Goud Hyderabad Institute of Technology and Management Hyderabad, Telangana, India Ayushi Jain Symbiosis Institute of Technology Pune, Maharashtra, India Sweety Jain Samrat Ashok Technological Institute Vidisha, Madhya Pradesh, India Partha Protim Kalita Dibrugarh University Assam, India S. Kannadhasan Study World College of Engineering Coimbatore, Tamil Nadu, India

K. Karthika Kumaraguru College of Technology Coimbatore, Tamil Nadu, India K. Kavitha Velammal College of Engineering and Technology Viraganur, Tamil Nadu, India Kalyan Sundar Kola GMR Institute of Technology Rajam, Andhra Pradesh, India Praveen Kumar National Institute of Technology Jamshedpur Jamshedpur, Jharkhand, India Ranjeet Kumar National Institute of Technology Jamshedpur Jamshedpur, Jharkhand, India Vicky Kumar JIS College of Engineering Kalyani, West Bengal, India Aparna Kundu Durgapur Institute of Advanced Technology and Management Durgapur, West Bengal, India Krishanu Kundu GL Bajaj Institute of Technology & Management Greater Noida, India Santosh Kumar Mahto Indian Institute of Information Tech­ nology Ranchi Ranchi, Jharkhand, India Santimoy Mandal R.V.S College of Engineering & Technology Jharkhand, India

Contributors

Tapan Mandal Govt. College of Engineering and Textile Technology Serampore, West Bengal, India Barun Mazumdar Gargi Memorial Institute of Technology Kolkata, West Bengal, India Santanu Mishra Haldia Institute of Technology Haldia, West Bengal, India Pratik Mondal Gayatri Vidya Parishad College of Engineering Madhurawada, Visakhapatnam, India R. Nagarajan Gnanamani College of Technology Tamilnadu, India Biswarup Neogi JIS College of Engineering Kalyani, West Bengal, India Pravesh Pal National Institute of Technology Jamshedpur Jamshedpur, Jharkhand, India Aparna Panja National Institute of Technology Durgapur Durgapur, West Bengal, India

xxvii

A. Mallikarjuna Prasad University College of Engineering Kakinada, Andhra Pradesh, India S. Raghavan National Institute of Technology Trichy Trichy, Tamil Nadu, India Praful Ranjan Government Girls Polytechnic Varanasi Varanasi, Uttar Pradesh, India N. V. Koteswara Rao Chaitanya Bharathi Institute of Technology Hyderabad, Telangana, India Vanitha Rani Rentapalli VIT AP University Amaravati, Andhra Pradesh, India Bappadittya Roy VIT AP University Amaravati, Andhra Pradesh, India Koushik Roy United International University Dhaka, Bangladesh Gourisankar Roy Mahapatra Haldia Institute of Technology Haldia, West Bengal, India Vaibhav Saini Symbiosis Institute of Technology Pune, Maharashtra, India

Narendra Nath Pathak Dr. B. C. Roy Engineering College Durgapur, West Bengal, India

Amit Sarkar Indian Institute of Technology Bhubaneswar Bhubaneswar, Odisha, India

Kranti D. Patil Trinity Academy of Engineering Pune, Maharashtra, India

Manoj Sarkar CSIR-CEERI Pilani Rajasthan, India

xxviii

Contributors

Partha Pratim Sarkar University of Kalyani Kalyani, West Bengal, India Abhishek Sarkhel National Institute of Technology Meghalaya Shillong, Meghalaya, India M. Shobana JJ College of Engineering and Technology Tiruchirappalli, Tamil Nadu, India

Rashmi Sinha National Institute of Technology Jamshedpur Jamshedpur, Jharkhand, India G. Srividhya Gnanamani College of Technology Namakkal, Tamilnadu, India D.M. Yadav SND College of Engineering & Research Center Yeola, Maharashtra, India

Chapter 1

Microstrip Antennas Theory, Principles and Review of Literature Ankan Bhattacharya

1.1 INTRODUCTION The most popular and revolutionary wireless technology available to date are microstrip antennas. A radiating patch element and ground plane, both made of conducting materials (copper) on either side of a dielectric substrate material, are the basic constituents of a microstrip antenna [1]. Compared to conventional antennas, microstrip antennas have many advantageous features. They are cost-effective, lightweight, easy to reproduce, reliable, easy to fabricate, etc. They can have various configurations like rectangular, square, trapezoidal, circular, elliptical, etc. [2, 3]. Microstrip antennas can be applied from low- to high-frequency ranges, approximately from the MHz range to GHz. With the advancement of wireless technology, multiple band systems have come into the picture. However, this type of antenna has drawbacks that reduce their performance. The quality factor, Q, is very high in the case of microstrip antennas [4]. Q represents the various associ­ ated antenna losses. A narrow bandwidth results if the value of Q is very high. The substrate thickness can be reduced to reduce the Q value. But with the increment in substrate thickness, a major portion of the power from the source is lost as surface waves. Antenna efficiency, η, is also an important point of consideration. As pointed out by H. A. Wheeler in [5], the efficiency is limited due to coupling closeness of the antenna and its tuning element. The effect of antenna size on efficiency is discussed in [6] by R. F. Harrington. Radiation efficiency is related to the dissipation fac­ tor, D, which in turn depends on the electrical size of an antenna. For an antenna to be reasonably efficient, D should be close to unity. The maxi­ mum radiation efficiency of a small antenna, in fact, depends on its electri­ cal size, frequency of operation and the conductivity of the metal. For a broadband antenna, at the low frequencies, the antenna might well become electrically small. Therefore, the size of an antenna should be optimized to achieve the maximum radiation efficiency. Ideally a microstrip antenna should be able to transmit all the power i.e. it is fully efficient in technical

DOI: 10.1201/9781003459880-1

1

2

Advances in Microwave Engineering

terms. However, it fails to do so because of some unwanted power losses like metallic losses, dielectric losses, mismatch of impedance, etc. Further­ more, L. J. Chu discussed the certain physical limitations of omnidirectional antennas in [7]. Band-gap structures can be employed to minimize surface waves. Antenna arrays can be implemented as an alternative to overcome other drawbacks like low gain and low power. In wireless communication systems a rapid evolution has taken place. So the researchers are develop­ ing new radiating devices. Therefore, use of compact microstrip antennas is one of the solutions. In spite of a few disadvantages, microstrip antennas have other advantages. In the modern world, due to the tremendous techno­ logical advancements, the demand for compact antennas with a wide band­ width is increasing constantly. The two most popular wireless technologies prevailing today are wide local area network (WLAN) and WiMAX [8]. Antenna researchers are engaged in inventing novel techniques and formu­ las to achieve wide-bandwidth microstrip antennas to fulfill the demand of advancing communication technology. In earlier times, for a particular wireless system, a particular antenna type with a certain radiation pattern was implemented. If the antenna bandwidth is increased, it will help to fulfill the bandwidth requirement of other wireless communication stan­ dards. Microstrip antennas can be applied for G.S.M. 1800 (01.71–01.88 GHz), P.C.S. 1900 (10.93–01.99 GHz), G.P.S. (01.57–1.58 GHz), WiMAX (03.3–03.7 GHz) and WLAN bands (05.15–05.85 GHz) and also in sev­ eral other applications suited for commercial or military purposes [9]. The applications of microstrip antennas can also be extended to satellite com­ munications and remote sensing [10]. 1.2 MICROSTRIP PATCH ANTENNA DESIGN Researchers in antenna design have proposed various formulas and numeri­ cal methods to ease the computational means for designing microstrip anten­ nas [11]. A  microstrip patch antenna is basically made of a ground plane and patch element, both composed of conducting materials (generally Cu). In between the patch element and the ground plane, there is a substrate material, which possesses definite dielectric properties. The patch can be of various shapes and sizes. Photo-etching can be performed to design the patch and the feed. Patches may be of various shapes and sizes like square, circular, rectangular, elliptical, fractal, etc. The thickness of the patch should be, t ­5dB ïï Lf = í ­10, S11 ( f ) dB < ­10dB ï S11 ( f ) dB ³ ­10dB ïî0,

(6.1)

Next, the cost function is expressed as in (6.2) [10], 1 Cost = Xb

æ P L (f ) ö 1 ç å i =1 xb i ÷ ­ å ÷ Xa P xb­1 ç è ø Xb

æ åQ L (f ) ö ç j =1 xa j ÷ å ç ÷ Q Xa­1 ø è Xa

(6.2)

where ‘i ’ denotes the desired resonating frequencies, ‘ j’ denotes the sup­ pressed resonating frequencies, ‘X b ’ denotes the desired frequency bands and ‘X a ’ denotes the suppressed frequency bands. ‘Q’ and ‘P’ denote the fre­ quency points in the suppressed and targeted bands, respectively. Minimizing the cost function aims to achieve or allow a reflection coefficient below –10 dB in the desired frequency bands [10]. The cost function of the applied GA optimization in [11] determines the size of the slot and the placement of the switches to carry out four modes of operation. The number of operating bands determines the number of terms in the cost function. The cost function suggested in [11] operates well with single objective optimization algorithms and can be useful in designing ultrawideband (UWB) and wideband (WB) antennas with band notching features. GA optimization involved in [12]

Optimization Algorithms for Reconfigurable Antenna Design

89

utilizes a multiobjective optimization algorithm to accomplish frequency reconfiguration with –6 dB bandwidth as a fitness function (6.3). f b

+

fd

minimize ò éë S11 ( f , x ) + 6ùû df , ò éë S11 ( f a

+

df su ubject to x Î {0, 1}

N

(3)

fc

where the decision vector x the opposite at the switch position. The frequency range of interest is defined by f a , f b , f c and f d . S11 is expressed in decibel, and ‘N’ represents decision vec­ tor’s bit count. Single objective optimization is used to achieve good imped­ ance matching in the two desired bands. Pros and cons: • The GA doesn’t require a lot of mathematics to solve optimization problems [13]. • The GA provides a great deal of versatility in hybridizing domaindependent heuristics to apply a particular problem effectively. • In performing the global search, evolutionary operators make GA effective [13]. Only if the problem has certain convexity properties that effectively ensure that every local optimum is a global one can a global optimum be found. • Although the GA can locate the solution in the entire domain, it does not readily solve complex constraint issues, particularly for precise constraints, and huge assessments are often time-consuming. The improved GA (enhanced GAs, interval GAs, quantum GAs, etc.,[13, 14]) is suggested to overcome the shortcomings of the GA. Many improvements and enhancements to the simple GA optimization such as elitism and the use of steady-state algorithms have been developed and used. GA optimization is more often used in electromagnetic applications like the design of antenna arrays, wire antennas, frequency selective sur­ faces, microwave absorbers, radar target identification and the architecture of wireless networks [4]. However, a GA is subject to a local optimal solu­ tion and has a slow rate of convergence in practical applications [14].

6.2.2 Differential Evolution Differential evolution (DE) was first suggested by R. Storn and K. V. Price in 1995 [15]. DE is a powerful optimization technique used for solving realvalued, non-linear, non-differential and multimodal functions. It is a popula­ tion-based optimization technique working with a set of solutions changing over generations through selection, generation and replacement methods. Optimizing an antenna using DE usually requires the user to select only

90

Advances in Microwave Engineering

three parameters: the size of the population (M), crossover constant (Cr) and scaling constant (F). Like other EAs, DE allows parameters as floatingpoint variables, which not only permits encoding as real variables but is also mutated conveniently using floating-point arithmetic. Floating-point makes encoding and decoding completely transparent and prevents the user from selecting the resolution constraints. The important features of standard DE are: It follows a generational model, where the current population is replaced when the child population is created completely, and if the child trial vector is inferior to the parent, then the individual is preserved for the next generation, implying the presence of elitism at an individual level [16]. The DE algorithm minimizes or maximizes a given fitness function f (var1, var2, . . . , varN). An N-dimensional vector ‘x’ gives the possible solutions for an ‘N’ variable function as (6.4) [17]. f ( var1, var2, ¼.., varN ) = f ( x1, x2,¼.., xN )

(6.4)

Groups of NP vectors are called populations, whose vectors are called the members of P (5) [17]. P = {x (1) , x ( 2 ) , ¼.., x ( NP )}

(6.5)

A new generation or population is created from the parent population through recombination and selection. The initial population is generated for every parameter ‘i ’ of x for j = 1 to NP using the function (6.6) [17]. Xi ( j ) = XiL + rand ( b i ) ( XiH ­ XiL )

(6.6)

where b denotes the random variable distribution; X iH and X iL denote the upper and lower bounds for a given parameter, respectively. The difference between two vectors selected at random is used in DE to achieve the recom­ bination. DE algorithm requires two constants: 1) the crossover constant CR (usually 0.2–0.8) and 2) the mutation weight l [ 0,1] , determining how much the difference vectors change the original vector. Larger l values result in increased global value convergence, while smaller values decrease conver­ gence time. However, the smaller l values decrease the chances of converg­ ing to a global solution. After the child population is created, the selection function operates to determine which children and parent populations will be carried onto the next generation. The final step in DE is a stopping func­ tion [17]. The DE optimization technique has been utilized extensively in the design and synthesis of RF switches and antenna (feed position optimization). Optimization of the reflector parameters along with the feed array enhances gain and lowers the side lobes in spaceborne synthetic aperture radar (SAR)

Optimization Algorithms for Reconfigurable Antenna Design

91

design. A lot of researchers have worked on improving the DE algorithm for better efficiency and accuracy. Some of the modified versions are fast DE, parallel DE, hybrid DE, quantum DE, DE/and/either-or algorithm, opposi­ tion-based and neighborhood-based DE and a lot more. A detailed survey of these algorithms is provided in [18]. Pros: • Simple. • Has fewer control parameters without a trade-off in performance. • Can solve a wide range of problems like multimodal, unimodal, nonseparable and separable. • Space complexity is less and can handle large-scale expensive optimi­ zation problems. Cons: • Mutation operation lacks selection pressure. • The ability to search across large distances is limited for clustered populations. • Still faces premature convergence.

6.2.3 Covariance Matrix Adaptation Evolution Strategy Covariance matrix adaptation evolution strategy (CMA-ES) is an evolution strategy for solving non-linear functions with many parameters. This was developed by Hansen and Ostermeier. CMA-ES is self-adaptive and does not require parameter tuning. CMA-ES’s performance is not impacted by the initial values of the strategy parameters (parameters that parameter­ ize the mutation distribution). The detailed study of the working of gen­ eral CMA-ES is discussed in [19]. CMA-ES consists of three mechanisms: 1) derandomized adaptation, 2) cumulative step size and 3) covariance n matrix adaptation. First, a mean vector m Î R is randomly initialized inside its limits Lk £ mk £ U k , for k = 1, 2,...n, where ‘n’ represents the number of n´n parameters. Then a covariance matrix cov = s2C is defined, where C Î R is initialized to identity matrix I with s as the initial step size. Following the initialization, each step in the algorithm samples l new solutions for the next g + 1 generation from the multivariate normal distribution N (m, cov) as (6.7) [20]. Xk (

g +1)

(

~ N XW ( ) , s ( ) cov ( g

g

g)

)

(6.7)

where XW ( ) represents the recombination point, s ( g ) denotes the global step (g) size adaptation and cov represents the covariance matrix adaptation. The g

92

Advances in Microwave Engineering

initial value of σ is set generally to 0.5, l as 4 + [3ln (n)] and m as [ l / 2]. The loop starts to iteratively run after the distribution has been updated and continues until a stop condition is satisfied. The common stopping standards depend on: • • • •

The maximum iterations possible. A constraint on the fitness level to be attained. Negative definition of C matrix. Tolerance on the smallest standard deviation.

Pros: • Optimizes a problem space by producing new members around the best mean located in the gaussian hyper-space [20]. • Rotational invariance is useful for a rotationally ill-conditioned search space. • Robust, effective and quicker than all EAs. Cons: • Smaller global step sizes at initial stages lead to worse performance on multimodal functions. • This may lead to premature convergence as the new members created are scattered around a mean. • Standard CMA-ES cannot restore useful traits that have been lost. • Not suitable for problems to find a global minimum present at the edge of the feasible region. 6.3 SWARM INTELLIGENCE-BASED ALGORITHM

6.3.1 Particle Swarm Optimization The PSO was invented by R.C. Eberhart and James Kennedy. It is a bio­ logically derived algorithm, occupying the gap in nature between evolution­ ary search and requiring neural processing. Inspired by how flocks of birds or swarms of insects move about in search of food, PSO seeks to deter­ mine the most ideal solution in the search space. It includes a very basic concept and can be implemented in a few lines of coding. It is efficient in terms of speed and memory requirements, as it requires simple mathemati­ cal operations. PSO is an effective, efficient, robust and accurate algorithm that finds the optimum much easier than traditional methods. It finds the solution to any specific issue in a search space within a period and balances between exploitation and exploration very efficiently. It is fast for non-linear,

Optimization Algorithms for Reconfigurable Antenna Design

93

non-differentiable and multimodal problems. But unlike other EAs, the PSO is based on correlations of biological behavior and not on natural evolution [21]. The PSO algorithm gives each swarm particle equal weight during the entire search process. In each iteration, the position and velocity of each of the particles are modified following the best positions of the particles them­ selves and the group obtained thus far, thereby not implementing the theory of survival of the fittest. It is used in system design, power allocation of coop­ erative communication networks, artificial neural networks, machine learn­ ing, character and pattern recognition, signal processing, decision-making and identification. The initial search space has a set of feasible solutions that are randomly placed in the search space. Every single particle of the swarm evaluates its fitness at that point and then starts to move in the search space for a fixed number of iterations in search of better fitness as soon as they are given a velocity. Every individual particle must maintain its location in the search space concerning the fitness function obtained. The movement of the par­ ticles is based on their own best location (pbest) as well as on the best loca­ tion obtained by other particles in the swarm (gbest). The algorithm thus finds the best possible solution to the fitness function in the search space in subsequent iterations. The fitness function is usually defined by a math­ ematical function to evaluate the system performance and is solely based on the application of the algorithm. A basic PSO uses a swarm of ‘n’ particles, and the position of every individual particle indicates a possible solution in the search space. The particle updates its conditions based on three factors: its own most optimal solution, its inertia and the swarm’s most optimal solution. The velocity and position of the particles change according to (6.8) and (6.9) [21]. vidk+1 = wvidk + c1r1k ( pbestidk ­ xidk ) + c2 r2k ( gbestidk ­ xidk )

(6.8)

Xidk+1 = xidk + vidk+1

(6.9)

where vidk denotes the velocity, Xidk denotes position, pbestkid characterizes the personal best position and gbestkid is the global best position (group’s best value) of the ith particle at the ‘d’ dimension in the kth iteration. ‘w’ is the inertial weight given to the particle’s previous position. r1k and r2k denote the random function in the range [0,1]. C1 and C2 are acceleration constants. Each particle of the search space is fastened onto the maximum velocity, Vmax, which defines the fineness or resolution by which regions can be sorted out among the current position and the target position [21]. How­ ever, particles might miss some good locations if Vmax is too high, or some good places will be out of reach if Vmax is too low. So, the inertial weight

94

Advances in Microwave Engineering

(‘w’) is introduced to eliminate the Vmax dependency. Inertial weight con­ trols the speed of convergence of the algorithm. Higher values of ‘w’ pro­ vide improved global search capabilities, and the reverse results in improved searching of local minima. Acceleration constants C1 and C2 relate the speed of particles flying to their own best position and the swarm’s fittest location. These acceleration constants stand in for the weighing of acceleration terms towards the gbest and pbest positions. The particle may exceed a fit position if the values are too high, and it may not reach the location if the values are too low. A value of 2 is typically assigned to the constants C1 and C2 to shift the times taken toward the pbest of the particle and the gbest of the swarm as equal and by half of the overall time. The particles are attracted to the gbest and pbest positions by adding random numbers. By doing this, the system is prevented from being trapped at local minima or maxima. Three components make up the velocity update: 1) the ability of the par­ ticle to proceed in the same direction as it did during the prior iteration, called momentum; 2) pulling the velocity of the particle towards its pbest, called memory or remembrance or cognitive part; and 3) pulling the velocity of the particle towards the gbest, called cooperation or social knowledge or social part. The fitness evaluation feature of the PSO algorithm, calculated using (6.10), is used to show how effectively a solution satisfies a design parameter [22]. N

F = åWi fi

(6.10)

i =0

In (6.12), the fitness factor is denoted by ‘N’, the weighing coefficient is expressed by ‘Wi’ and the ith fitness factor value is represented by ‘f i ’. The fitness function to get resonance at a targeted frequency can be obtained using (6.11) [22, 23]. 2 Fitness = min ( S11n )

fr

(6.11)

where S11 represents return loss, ‘n’ denotes the sample point in the S11 Vs frequency and ‘f r ’ represents the resonating frequency. PSO with velocity mutation can solve multiple complex variables with multiobjective goals in the least possible computational time [24]. Pros: • Search is done by repeated variation of particle velocity and not by selection or mutation operations. • Particles move only to optimal locations because of gbest. • Can be used in scientific and engineering applications. • Calculations are simple and easy. • Its parallel execution improves the speed of the process.

Optimization Algorithms for Reconfigurable Antenna Design

95

Cons: • An increase in the dimension of the search space results in increased complexity. • Vulnerable to partial optimism and may lead to inaccuracy. • Cannot be used for non-coordinate systems due to the lack of dimensionality. • This can result in a loss of diversity due to high convergence.

6.3.2 Grey Wolf Optimizer The grey wolf optimizer (GWO) was suggested by Mirjalili in 2014 as a new metaheuristic swarm intelligence-based algorithm. GWO imitates the group hunting behavior and grey wolves’ social hierarchy in nature. The grey wolf follows a very strict hierarchy compiled of all members of the pack (group of grey wolves) as illustrated in Figure 6.1. The alpha wolves (a) hold the top position in the hierarchy and act as the leaders of the pack. They dominate and command other wolves and are accountable for managing the group in hunting, migration and feeding. They need not be the strongest of all, but they are the best at managing the entire pack. The betas (b) are in the second level. Beta wolves act as an advisor to the alpha and help to instruct the lower-level wolves. Betas are suitable candidates for leadership positions when the alpha is sick, injured or dead. The delta wolves (δ) form the third level in the hierarchy, and they act as elders, sentinels, scouts, hunters and caretakers of the pack. They obey the

Figure 6.1 Grey wolf’s social hierarchy (dominance increases from bottom up) [25].

96

Advances in Microwave Engineering

alphas and betas but dominate the lower-level omegas. The lowest level is occupied by the omegas (w) which are dominated by other wolves. They act as scapegoats. But they form an essential part of the pack because of their assistance and the pack’s desire to maintain their overall organization. The GWO algorithm is given in the following phases. 6.3.2.1 Social Hierarchy The algorithm starts by defining the objective functions and related param­ eters. According to the hierarchy of the pack, the mathematical model assumes the best solution found to be alphas, the second-best solution is betas, the third is deltas and the remaining candidate solutions are omegas [26]. Alphas, betas and deltas guide the hunting. 6.3.2.2 Group Hunting 6.3.2.2.1 Encircling Prey Tracking and encircling the prey is the initial move in a search. Mathemati­ cally, the encircling of prey/solution is given using (6.12) and (6.13) [26]: X ( t + 1) = Xp ( t ) ­ AiD

(6.12)

D = CiXp ( t ) ­ X ( t )

(6.13)

where X ( t + 1) and X ( t ) represent the position of a grey wolf at ( t + 1) and t th positions and X P ( t ) represents the prey’s position. C and A are given as the coefficient vectors in (6.14) and (6.15) [26]: th

C = 2r2

(6.14)

A = ( 2r1 ia ) ­ a

(6.15)

where r1 and r2 represent two random vectors in [0,1], ‘a’ is an encircling coefficient vector whose values decrease from 2 to 0 over the iterations of the search and are calculated using (6.16) [26].

(

a = 2 1­ t

T

)

(6.16)

where ‘T’ and ‘ t ’ are the maximum number of iterations and current itera­ tions, respectively. Using (6.12) and (6.13), a candidate solution/grey wolf updates its position around the optimal solution prey. The position of a wolf can be moved by adjusting A and C vectors. The r1 and r2 are utilized to simulate various movement velocities and step sizes [26]. This encircling can be also done in n-dimensional space.

Optimization Algorithms for Reconfigurable Antenna Design

97

6.3.2.2.2 Hunting The alpha leads the pack together on a hunt. They may select the potential prey and select the break-off of the hunt. The betas and deltas join the alpha in hunting. The omegas may be a caretaker for the newborn or the injured. This group hunting is represented mathematically using (6.17)–(6.19) [26]: Da = C1 iXalpha ­ X ; Db = C2 iXbeta ­ X ; Dd = C3 iXdelta ­ X

(6.17)

X1 = Xalpha ­ A1 iDa ; X2 = Xbeta ­ A2 iDb ; X3 = Xdelta ­ A3 iDd

(6.18)

X ( t + 1) = (X1 + X2 + X3 ) / 3

(6.19)

where X alpha , X beta , X delta and X represent the alpha, beta, delta and omega positions, respectively, in the tth iteration; the updated position of ω in the (t + 1) iteration is denoted by X(t + 1). From Figure 6.2, it is observed that the alpha wolf, beta wolf and delta wolf work to identify the prey’s position, and then ω updates its positions accordingly. Likewise, the hunting wolves randomly update their position close to the prey under the guidance of the present top three wolves. Then the hunting wolves start searching for the prey’s position and concentrate on attacking [25].

Figure 6.2 Updating of position in GWO [25].

98

Advances in Microwave Engineering

6.3.2.2.3 Attacking Prey (Exploitation) The wolves strike their target by controlling the ‘A’ vector using (6.17). It is observed that when A = 1, the wolves surround the prey, and when A < 1, the wolves attack the target by converging toward the prey (exploitation) [25]. Since ‘A’ depends on ‘a’, and ‘a’ decreases linearly between 2 and 0, the A’s value also decreases in the range [–2a,2a]. Thus, it is inferred that the wolves may launch closer attacks after more iterations. 6.3.2.2.4 Tracking Prey (Exploration) When A > 1, the wolves start to diverge and explore other areas in the search space to find better prey (exploration phase).‘C’ helps in exploration, and it takes random values in [0,2]. It alters the prey’s contribution in deciding the location of omega wolves in the next steps. When C > 1, the wolves advance quickly toward their prey; when C < 1, it has a negative effect by slowing down the movement [25]. It can be seen from (6.10) and (6.11) that ‘C’ has minimal impact on the final stage update of X ( t + 1) since ‘A’ reduces linearly from 2 to 0. Both these vectors ‘C’ and ‘A’ act as minor disturbances due to their random and adaptive nature, which greatly helps the search to not converge into local optimum. The exploitation and exploration must be handled properly. The exploi­ tation searches the neighborhood spaces for its solution, while exploration leads to searches extensively to not be trapped in a local minimum. Hence, a balance between both is required or else it may create a premature conver­ gence or a non-optimal solution. The balance is handled by parameter ‘A’, as values 1 lead to exploration [26]. Over the iterations, the wolves search the position of prey, and they update their values when better values are found. The grey wolf algorithm is ceased when a maximum count of iterations is achieved. Pros: • • • •

Has fewer tunable parameters (A and C). Reduced computation and high performance. Eliminates the need for selecting the best operator. Easy to implement with less space complexity.

Cons: • No assurance of premature convergence. • Slow convergence. • Low solving precision. Some of its updated versions, EGWO, IGWO, MOGWO, MAL-IGWO, RW-GWO [27] and a lot more, are proposed frequently and are modified

Optimization Algorithms for Reconfigurable Antenna Design

99

for specific applications such as power flow control and voltage stability enhancement. Some of the prominent works in reconfigurable antenna design with opti­ mization algorithms are represented in Table  6.1. From the study, we can Table 6.1 Reconfigurable Antenna Design Implemented Using Optimization Algorithms Ref. No. Reconfiguration/ Optimized Optimization Antenna Parameters

Single Means of Objective/ Optimization Multiobjective

[9]

Frequency/GA

Impedance Matching

Single

[10]

Frequency/GA

Impedance matching

Single

[11]

Frequency/GA

Bandwidth

Single

[12]

Frequency/GA

• Reflection Multi­ coefficient • No. of switches

[28]

Pattern/DE

Reflection coefficient

Single

• Slot shape • Location of switches in the ground

Control Parameters

• Population size = 200 • Crossover probability (0.75) • Maximum no. of generations = 50 • Mutation probability (0.35) • Free from • Population constraints size = 20 • Automatic • Crossover allocation of probability (100 %) switches • Maximum no. of generations = 30 • Mutation probability (0.1%) • Slot shape • Population • Location of size = 50 switches in the • Crossover ground probability (1) • Maximum no. of generations = 100 • Mutation probability (0.1) • Population size = 500 • Crossover probability (0.8) • Maximum no. of generations = 200 • Mutation probability (0.01) • Dimensions • Population of the size = 10, 20 geometry • Crossover constant = 0.5 • Maximum iteration = 20 • Mutation scale factor F = 0.25 (Continued)

100

Advances in Microwave Engineering

Table 6.1 (Continued) Ref. No. Reconfiguration/ Optimized Optimization Antenna Parameters [24]

[29]

[30]

Single Means of Objective/ Optimization Multiobjective

Control Parameters

• Low SWR Multi­ at the input • Tilt in main lobe • High gain • Service area null filling • Outside service area • Low side lobe levels Frequency/PSO Impedance Single matching

• Dimensions of the Geometry • Array feeding weights

• No. of swarm particles: 20 • Maximum no. of iterations = 2000

• Dimensions of the geometry

Reconfigurable FSS/hybrid PSO with negative zone

• Geometry Modification

• No. of swarm particles: 14 • Maximum no. of iterations = 500 • No. of Swarm particles: 10 • Maximum no. of iterations = 200

Pattern/PSO with velocity mutation

Band pass Multi­ and band stop filtering action

observe that GA originates from the natural evolution process. The chro­ mosome represents the solution, and genes represent the parameters of the solution. GA is widely used in wireless applications. However, sometimes it can take a while to discover the optimal solution. DE is an evolutionary algo­ rithm that employs population statistics. It draws inspiration from natural laws on human evolution. DE is a modified version of the GA. The employ­ ment of similar operators in different ways distinguishes DE from GA. Com­ pared to other EAs, DE requires only a few parameters to be adjusted and is simple to implement. These features helped it become popular. CMA-ES, a branch of evolution strategy, is useful when there is no direct way to ascer­ tain the parameter set. The PSO algorithm is motivated by birds’ flocking behavior. The solution is characterized by the particle. Local best position, global best position, position and velocity are the parameters of the solution. Optimization is a promising research area in antenna design. There are several possible future improvements that could be made to enhance the per­ formance of antennas further. Some of the potential areas of improvement include artificial intelligence, metamaterials, non-linear optimization and additive manufacturing. These techniques can help in generating optimized antenna designs with unprecedented performance characteristics, making them suitable for a wide range of applications in communication, sensing and other fields. The world of optimization algorithms is so large that it won’t fit

Optimization Algorithms for Reconfigurable Antenna Design

101

in this single review. They can be physics-oriented, evolutionary algorithms, or swarm intelligence. The common EAs not addressed in this chapter are evolutionary programming, evolutionary strategy, genetic programming and biogeography-based optimizers. A few of the widely implemented physicsbased algorithms are gravitational local search, gravitational search algo­ rithm, charged system search, big bang big crunch, black hole small-world optimization, galaxy-based search optimization and curved space optimiza­ tion. Similarly, some of the swarm intelligence-based algorithms are artificial fish swarms, wasp swarm algorithms, monkey search, cuckoo search, bee collecting pollen algorithm and firefly algorithm. 6.4 CONCLUSION Reconfigurable antennas can be used in numerous wireless communication applications. These antennas reduce the system complexity by eliminating the need for additional antennas in a communication system. Optimization algorithms are highly useful in reconfigurable antenna design to minimize the complexity of the structure and feeding mechanism and to enhance its recon­ figurability. These meta-heuristic optimization algorithms have become very popular in this modern age and are well known not only in antenna design but also in various fields of study. They are adaptive to various applications and are readily applicable to various types of problems since they only con­ sider the input and output of a problem. Various optimization algorithms are explored in this work. Among these, GA and PSO are quite common in antenna designs. The trust region framework (TRF) algorithm acts as the best candidate for solving multiobjective and multiple-variable problems in antenna design. As per analysis of these optimization methods, it is impos­ sible to identify one optimization algorithm as the best fit among them all. They remain simple algorithms inspired by natural phenomena which can assure the evolution of better algorithms in the future. REFERENCES [1] E. R. Brown, “RF-MEMS switches for reconfigurable integrated circuits,” IEEE Trans Microw Theory Tech, vol. 46, no. 11, Part 2, pp. 1868–1880, 1998. doi: 10.1109/22.734501. [2] K. Karthika and K. Kavitha, “Reconfigurable antennas for advanced wire­ less communications: A  review,” Wirel. Personal Commun., vol. 120, no. 4, pp. 2711–2771, Oct. 01, 2021. doi: 10.1007/s11277-021-08555-4. [3] G. S. Hornby, J. D. Lohn, and D. S. Linden, “Computer-automated evolution of an X-band antenna for NASA’s space technology 5 mission,” Evol Comput, vol. 19, no. 1, pp. 1–23, 2011. doi: 10.1162/EVCO-a-00005.

102

Advances in Microwave Engineering

[4] J. M. Johnson and Y. Rahmat-Samii, “Genetic algorithms in engineering elec­ tromagnetics,” IEEE Antennas Propag Mag, vol. 39, no. 4, pp. 7–21, 1997. doi: 10.1109/74.632992. [5] D. Marcano and F. Duran, “Synthesis of antenna arrays using genetic algo­ rithms,” IEEE Antennas Propag Mag, vol. 42, no. 3, pp.  12–20, 2000. doi: 10.1109/74.848944. [6] J. H. Holland, Adaptation in Natural and Artificial Systems. Ann Arbor, MI: University of Michigan Press, 1975. [7] K. A. De Jong, “An analysis of the behavior of a class of genetic adaptive sys­ tems,” 1975. https://deepblue.lib.umich.edu/handle/2027.42/4507. [8] J. M. Johnson and Y. Rahmat-Samii, “Genetic algorithm optimization and its application to antenna design,” IEEE Antennas Propag. Soc., vol. 1, pp. 326– 329, 1994. doi: 10.1109/aps.1994.407746. [9] F. Zadehparizi and S. Jam, “Design of frequency reconfigurable patch anten­ nas with defected ground structures using genetic algorithm,” Iran. J. Sci. Technol Trans Electr. Eng., Vol. 42, no. 4, pp. 485–491, 2018. doi: 10.1007/ s40998-018-0065-5. [10] K. Fertas, F. Fertas, S. Tebache, A. Mansoul, and R. Aksas, “Genetic algorithm based approach for frequency switchable dual-band patch antenna,” Iran. J. Electr. Electr. Eng, vol. 18, no. 3, 2022. doi: 10.22068/IJEEE.18.3.2454. [11] F. Zadehparizi and S. Jam, “Frequency reconfigurable antennas design for cog­ nitive radio applications with different number of sub-bands based on genetic algorithm,” Wirel Pers Commun, vol. 98, no. 4, pp. 3431–3441, Feb. 2018. doi: 10.1007/s11277-017-5022-5. [12] S. Song and R. D. Murch, “An efficient approach for optimizing frequency reconfigurable pixel antennas using genetic algorithms,” IEEE Trans Antennas Propag, Vol. 62, no. 2, pp. 609–620, 2014. doi: 10.1109/TAP.2013.2293509. [13] P. Guo, X. Wang, and Y. Han, “The enhanced genetic algorithms for the optimi­ zation design,” Proceedings—2010 3rd International Conference on Biomedi­ cal Engineering and Informatics, BMEI 2010, vol. 7, no. Bmei, pp. 2990–2994, 2010. doi: 10.1109/BMEI.2010.5639829. [14] G. Chen, H. Jiang, and X. Lei, “Reconfigurable antenna design optimization based on improved quantum genetic algorithm,” 2014 31th URSI General Assembly and Scientific Symposium, URSi GASS 2014, no. 7, pp. 3–6, 2014. doi: 10.1109/URSIGASS.2014.6929190. [15] R. Storn and K. Price, “Differential evolution—a simple and efficient heuristic for global optimization over continuous spaces,” Journal of Global Optimiza­ tion, Vol. 11, no. 4, pp. 341–359, 1997. doi: 10.1023/A:1008202821328. [16] N. Padhye, P. Mittal, and K. Deb, “Differential evolution: performances and analyses,” 2013 IEEE Congress on Evolutionary Computation, CEc 2013, no. i, pp. 1960–1967, 2013. doi: 10.1109/CEC.2013.6557799. [17] J. H. Van Sickel, K. Y. Lee, and J. S. Heo, “Differential evolution and its appli­ cations to power plant control,” in 2007 International Conference on Intel­ ligent Systems Applications to Power Systems, 2007, pp.  1–6. doi: 10.1109/ ISAP.2007.4441675. [18] S. Das and P. N. Suganthan, “Differential evolution: A survey of the state-of-the­ art,” IEEE Trans. Evol Comput, vol. 15, no. 1, pp. 4–31, 2011. doi: 10.1109/ TEVC.2010.2059031.

Optimization Algorithms for Reconfigurable Antenna Design

103

[19] N. Hansen and A. Ostermeier, “Completely derandomized self-adaptation in evolution strategies.,” Evol Comput, vol. 9, no. 2, pp.  159–195, 2001. doi: 10.1162/106365601750190398. [20] R. Kundu, R. Mukherjee, S. Debchoudhury, S. Das, P. N. Suganthan, and T. Vas­ ilakos, “Improved CMA-ES with memory based directed individual generation for real parameter optimization,” 2013 IEEE Congress on Evolutionary Com­ putation, CEC 2013, pp. 748–755, 2013. doi: 10.1109/CEC.2013.6557643. [21] M. Juneja and S. K. Nagar, “Particle swarm optimization algorithm and its parameters: A review,” ICCCCM 2016–2nd IEEE International Conference on Control Computing Communication and Materials, no. ICCCCM, 2017. doi: 10.1109/ICCCCM.2016.7918233. [22] Y. K. Choukiker, S. K. Behera, B. K. Pandey, and R. Jyoti, “Optimization of plannar antenna for ISM band using PSO,” in 2010 Second International con­ ference on Computing, Communication and Networking Technologies, 2010, pp. 1–4. doi: 10.1109/ICCCNT.2010.5591601. [23] F. J. Ares-Pena, J. A. Rodriguez-Gonzalez, E. Villanueva-Lopez, and S. R. Ren­ garajan, “Genetic algorithms in the design and optimization of antenna array patterns,” IEEE Trans Antennas Propag, vol. 47, no. 3, pp. 506–510, 1999. doi: 10.1109/8.768786. [24] I. P. Gravas, Z. D. Zaharis, P. I. Lazaridis, T. V. Yioultsis, N. V. Kantartzis, C. S. Antonopoulos, I. P. Chochliouros, and T. D. Xenos, “Optimal design of ape­ riodic reconfigurable antenna array suitable for broadcasting applications,” Electronics, vol. 9, no. 5, 818, May 2020. doi: 10.3390/electronics9050818. [25] S. Mirjalili, S. M. Mirjalili, and A. Lewis, “Grey wolf optimizer,” Adv. Eng. Soft., vol. 69, pp. 46–61, 2014. doi: 10.1016/j.advengsoft.2013.12.007. [26] X. Li and K. M. Luk, “The grey wolf optimizer and its applications in electromagnetics,” IEEE Trans Antennas Propag, vol. 68, no. 3, pp. 2186–2197, 2020. doi: 10.1109/TAP.2019.2938703. [27] M. W. Guo, J. S. Wang, L. F. Zhu, S. S. Guo, and W. Xie, An Improved Grey Wolf Optimizer Based on Tracking and Seeking Modes to Solve Function Opti­ mization Problems, vol. 8. IEEE, 2020. doi: 10.1109/ACCESS.2020.2984321. [28] P. Mahouti, “Design optimization of a pattern reconfigurable microstrip antenna using differential evolution and 3D EM simulation-based neural net­ work model,” Int. J. RF Microw. Comput Aided Eng., vol. 29, no. 8, Aug. 2019. doi: 10.1002/mmce.21796. [29] S. Shoukhath, “Design of MEMS Reconfigurable E-Shaped Patch Antenna Design for Cognitive radio.” [Online]. Available: www.ijert.org. [30] P. Lacouth, A. G. D’Assunção, and A. G. Neto, “Synthesis of new reconfigurable limited size FSS structures using an improved hybrid particle swarm optimiza­ tion,” J. Microwaves Optoelectron. Electromagn. Appl., vol. 18, no. 2, pp. 157– 172, 2019. doi: 10.1590/2179-10742019v18i21550.

Chapter 7

Review on Wearable Antennas for IoT, Healthcare, and HighEnd Applications Vaibhav Saini , Praful Ranjan , and Ayushi Jain

7.1 INTRODUCTION Fourth-generation (4G) mobile communication systems now heavily rely on body-centric wireless communication [1]. Body-centric connectivity has a firm place in body area networks (BANs) and personalized network connectivity (PANs) [2]. There are two forms of body connectivity: off-body connectiv­ ity and on-body connectivity. Off-body connectivity refers to the radio link between base units or wireless devices located outside the body and devices that are worn on the body. Lastly, in-body connectivity is the exchange of infor­ mation between on-body nodes and wireless medical devices. In other terms, a wearable antenna is any antenna that is particularly designed to work while being worn. Smartwatches, which frequently have built-in Bluetooth antennas; glasses such as smart glasses, which have Wi-Fi connection and global posi­ tioning system antenna arrays [3]; GoPro action cameras, which have Wi-Fi and Bluetooth antennas and are often strapped to users to obtain video clips; and even the fitness tracking sensor, which connects to a smartphone via Bluetooth and is placed in a person’s shoe, are some of the most commonly used examples in daily life. Because wearable antennas are increasingly being used in consumer electronics, this chapter is dedicated to explaining the issues con­ nected with wireless antenna design. Wearable, fabric-based antennas are cur­ rently the most advanced research subjects in antennas. For all contemporary applications, wearable antennas [4, 5] must typically be lightweight, inexpen­ sive, almost maintenance-free, and require no installation. Many specialized occupational groups use body-centric communication systems, including para­ medics, firefighters, and the military. Additionally, wearable antennas can be used for monitoring small children, the elderly, and sportsmen [6]. 7.2 WEARABLE ANTENNA TYPES

7.2.1 Traditional Wearable Designs Traditional antenna layouts such as rectangular dipoles, monopoles, planar inverted F arrays (PIFAs), and previous studies employed microstrip patches 104

DOI: 10.1201/9781003459880-7

Review on Wearable Antennas

105

Figure 7.1 Construction of PIFA.

Figure 7.2 Placement possibilities of antennas.

for antenna structural deterioration. Construction of PIFA is shown in Fig­ ure 7.1. Printed circuit boards (PCBs) can be used to make planar microstrip antennas [7]. Due to their inexpensive price and ease of production, they became a useful type of antenna. In order to create a wearable antenna that could be attached to a garment’s sleeve, Salonen investigated an antenna using a PIFA design. PIFAs have a folded structure that is parallel to the ground plane, like quarter-wave monopole antennas [8]. One potential site for the antenna is on a shirt sleeve. This also highlighted how the bottom layer of the antenna affects the overall direction of the strongest emission. The ground plane protected humans by acting as a barrier, preventing radia­ tion from entering their bodies. To put it another way, the bottom layer served as a radiation reflection. A portable adjustable planar upside-down antenna (flex PIFA) supporting wireless gadgets was created and released based on the identical antenna design principle. The flexible material of the antenna was designed to be installed on a human arm and has a thickness of 0.236 mm, a dielectric constant of 3.29, and a loss tangent of 0.0004. Low profile, 100 MH to 500 MHz operation, omnidirectional azimuth cover­ age, wideband return loss, and vertical or circular polarization are antenna criteria that influence antenna selection. A wearable antenna should have an

106

Advances in Microwave Engineering

omnidirectional radiation pattern so that it can be used with mobile devices and smart apparel. In addition, omnidirectional radiation patterns should be created with little to no side lobes, as they can be harmful to human health.

7.2.2 Textile Design Antenna It is necessary to check the directional antenna’s dependability in different means of application where the user is moving. This dynamism causes the body’s orientation to fluctuate constantly. The antenna may continue to receive signals regardless of how the body is oriented because a polarization wave emits energy in all planes, including the horizontal, vertical, and any angular planes in between. Polyimide spacer fabric with a thickness of 6 mm and a permittivity of 1.5 is the substrate utilized in the design [9]. The ground plane and antenna patch were both made of a conductive substance, a woven textile that was nickel-plated. Circular polarization was also used to create a textile antenna for protective apparel in [8] in order to enhance reception in actual use. By positioning the patch’s feed point in a circular pattern, the design was able to excite the two orthogonally polarized TM01 and TM10 modes [10]. One of the areas of electromagnetic research that is moving forward the fastest is the electromagnetic band gap (EBG) [11]. The ground plane created with an EBG structure resembles a flawless conductor that is made up of magnets. Applying an EBG layer to the ground plane lowered the antenna’s return loss, making it about equal for all resonant frequencies, according to the S11 test (at –15 dB). It was totally constructed of textiles. When compared with other traditional planar antenna feeds, the design’s aperture-coupled feeding method helped to increase bandwidth. 7.3 CREATING AND DESIGNING OF WEARABLE ANTENNAS

7.3.1 Conductive Substance Conductive items like textiles are produced by weaving conductive metal or polymer threads into regular cloth. These materials’ wearable, sturdy, and flexible qualities made them perfect for incorporation into apparel. One well-known study covered the need for conductive textiles while creating textile antennas. In order to reduce losses, it was preferred that the conduc­ tive textile have a low and steady electrical resistance (/square). It was also necessary for the material to be flexible so that the antenna could distort. This chapter illustrates how a different researcher in [12] employed an easy requirement that could be covered in an arm. The substance employed had a 0.125 mm thickness and a 0.05 sq. in. surface resistance of woven con­ ductive fabric type. When building an antenna, choosing the right material is essential for it to be durable and appropriate for the intended purposes.

Review on Wearable Antennas

107

The substance used in the study in [13], an aramid woven fabric, is heat proof and appropriate for inclusion into firefighter apparel. The conductor in [14] was a nylon that has been metalized and is very conductive. High conductivity was supplied by its three metalized layers (Ni, Cu, and Ag), whereas the surface resistance was just 0.03/square. In addition, the sub­ stances offered rusting and pliability resistance, which made it appropriate for use in harsh environments.

7.3.2 Fabrication Method In contrast to stand-alone antenna testing performed without the presence of a human body, on-body evaluations must be undertaken to evaluate the antenna’s performance in various configurations. Depending on how they are used, wearable antennas may have different positions. The manufactured antenna was evaluated in [15] on the human arm, chest, and in free space. Researchers went so far as to include the human body in the measurement in [13]. According to the findings of previous studies, the antenna, which is located on the backside of the body, provides the most stable spot and will reduce changes in body orientation when compared to certain other anatomical structures such as the arm. 7.4 ANALYSIS REQUIRED FOR WEARABLE ANTENNAS Characteristic impedance, radiation pattern, gain, and effectiveness are often required for a typical antenna structure. Investigating its bending character­ istic is not essential because common planar antennas are flattened. A wear­ able antenna, on the other hand, demands careful consideration of extra criteria in order to assure the antenna’s operation when worn on the body. This section includes additional observations that should be taken in order to evaluate a wearable antenna design.

7.4.1 SAR Modelling Power quality limits received by the human body must constantly be taken into consideration by engineers and researchers due to open public forums about the fitness consequences of radiation and international regulatory regulations. As a result, wireless devices’ specific absorption rate (SAR) has been established. Specific adiation rate limits that are most frequently used are those set by the Institute of Electrical and Electronics Engineers (IEEE) at 1.6 W/kg for every 1 g of tissue and the International Commission on Non-Ionizing Radiation Protection (ICNIRP) at 2 W/kg for every 10 g of tissue [16].

108

Advances in Microwave Engineering

7.4.2 Measurement with Different Bending Antenna structure measurements should be made in a variety of bending positions. This is done to guarantee that the antenna will work as expected in practical situations, especially when it is attached to circular body parts like an arm. S11 tests were performed using various antenna bending scenarios [17]. To study this bending property, the antenna that was wrapped around a plastic cylinder was measured. The frequency of the bending decreased as the bending grew smaller.

7.4.3 On-Body Measurements In addition to stand-alone antenna tests, which were done without a human body present, on-body evaluations must be performed to evaluate the effi­ cient outcomes of the antenna in various postures of the body [18]. Depend­ ing on how they are used, wearable antennas may have different positions. In the manufactured device, measurements were taken on the human arm, chest, and in zero gravity. Researchers even went so far as to measure using the human body.

7.4.4 Significance The wearable  antenna includes a broad range of application fields, such as wearables, the Internet of Things, medical applications, ultrawideband (UWB), telecommunications, defence applications, and electronics. The rapid downsizing of wireless devices has raised the importance of wearable devices in the industry today. A wearable antenna is a component of clothing used for connectivity, including localization and monitoring, portable com­ puters, wireless connectivity, and public safety. Wearable antennas offer the potential for omnipresent monitoring, communication, and energy gathering and storing by utilizing wireless body sensor networks for healthcare and pervasive applications. 7.5 APPLICATION OF WEARABLE ANTENNAS

7.5.1 Healthcare Active sensors and passive sensors are the two types of sensors used in the wearable category. The classification is ambiguous, and many authors use it the other way around. Although the concept of enabling differs from that of other fields of digital equipment, active sensors need the use of an additional power source to transform an signal (input) into a working signal (output), whereas passive sensors generate self-energy, being evaluated into a ben­ eficial potential outcome [19]. A thermocouple is an example of a passive

Review on Wearable Antennas

109

Table 7.1 Wearable Biomedical Device Measurements Evaluation Flow of blood BP measurement ECG Electroencephalography Electromyography pH level insights Respiratory rate Temperature rate

Parameter

Frequency, Hz

1–300 mL/s 0–400 mmHg 0.5–5 mV 5–300 µV 0.1–5 mV 3–13 2–50 breaths/min 32–40°C

0–20 0–50 0.05–150 0.5–150 0–10,000 0–1 0–10 0–0.1

sensor that is commonly employed in research settings to monitor body tem­ perature or other phenomena. Patients’ vital signs can be picked up by a network of sensors and sent back towards the functional nodes. This section discusses textile sensors used on the human body, their properties for gather­ ing crucial physiological signals, and their incorporation into smart clothing. Sensors must be a basic component of all sensor networks, and advance­ ments in circuit design, sensor fusion, micro-electro-mechanical systems, and nanostructures have a substantial influence on sensor quality. Physiological sensors assess physical signs such as vital signs, regular blood glucose surveil­ lance, bloodstream blood oxygenation, and breathing rate [20]. In addition to core temperature, vital signs, heart rate, and breathing rate, physiological parameters may include measures like posture and movements, blood oxy­ genation, and electrocardiogram (ECG.). Table  7.1 lists the wearable bio­ medical device measurements. Body temperature is one of the few medical signs that is either constant or varies extremely slowly. These biosensors are converting dynamic, rather than static, biosignals, which depend on time.

7.5.2 Sports and Fitness Sports players’ performance, comfort, and awareness have all increased as a result of wearing smart materials. Sports have also sparked a lot of research in the smart textile sector, leading to innovations like breathable clothing and moisture-management materials. By absorbing excess heat and releasing it when necessary, phase-change technology, a recent development in smart textiles, has made it possible to regulate body temperature. It is now pos­ sible to instantly detect an athlete’s metabolic status and biological condition thanks to recent improvements in textile materials. Stitched-in piezoelectric sensors contribute with kinematic analysis, which improves movements and lowers injuries [21]. Furthermore, these sensors provide vital real-time data for tracking per­ formance and are always operational for continuous monitoring. Because

110

Advances in Microwave Engineering

they feature an accelerometer, radio frequency identification, wireless mod­ ule, and motion sensor, smart training socks fall under the category of wear­ able sensors. Future smart textiles might feature chemical sensors embedded into garments that can extract data from sweat analysis [22].

7.5.3 Internet of Things The market has predicted that there will be 100  billion connected gadgets through 2030, increasing from the existing rate from around 27 billion. Simi­ lar to this, several names were given to the low-power wide area network (LPWAN) concept when it was first launched in the early 1990s, but its con­ nection topologies and networking protocols were the same [23]. Over the past ten years, LPWAN also gained popularity in the Internet of Things (IoT) and was emphasized by SIGFOX technologies. After Long Range entered the picture, cellular operators began to sell IoT devices with connectivity under the names LTE Cat-M and NB-IoT due to its popularity. As shown in Figure 7.3, a few prerequisites determine the quality of LPWAN technologies. According to requirements, several LPWAN technologies are implemented in various application areas based on this capability [24]. Let’s go over each of its features in turn. Low-power narrowband IoT technology connects various IoT devices and extends the range of wide-area network technology. Due to these characteristics, the technology can be used for the many applications. In [25], IoT technologies were widely used in many sectors and also in the agri­ culture sector with more productivity as outcome. The suggested wearable antenna in this research paper runs from 2.40 to 14.88 GHz, with a fractional bandwidth (FBW) of approximately 144.44%. The installation of an openended rectangular slit in the antenna array increases the bandwidth [26]. The tiny multiple-input, multiple-output (MIMO) diversity antenna dem­ onstrated in this paper [27] is unquestionably capable for communications, enabling an incredibly broad impedance bandwidth as well as band-notched

Figure 7.3 Anatomy of wireless technology.

Review on Wearable Antennas

111

Figure 7.4 Narrowband IoT.

Table 7.2 Applications of Wearable Antennas

Health Monitoring • BP device • Glucose check • Air filter • Hearing aid devices • ECG monitoring device

• • • •

IoT Smart watch with health monitoring Motion detector Step count technology Pulse count functionality

• • • • •

Fitness Tracker Personal tracker Calorie counter Sleep censor Posture tracking Active walking

• • • • •

Military Smart band GPS tracker Gesture-based devices Finger tracking Location-sharing device

characteristics for wireless local area networks (WLANs) and WiMAX. An LPWAN technology called NB-IoT was created to meet the demand for deep indoor penetration, extended coverage, and low-power devices. Overall, it can be said that this technology is a blessing for the IoT era because it enables devices to operate with greater network coverage, battery life, and spectrum efficiency. All generations of mobile networks can be compatible with NB-IoT technology, which can also address the issues of coverage and consumption. Additionally, it may be incorporated into all current mobile communication devices, including smartphones, IoT modules, and other chipset devices. For better simulation and mathematical results, industries and labs are using MATLAB and Simulink for automation and better outcomes [28]. Applica­ tions of wearable antennas have been reflected in Table 7.2.

112

Advances in Microwave Engineering

7.6 CONCLUSION AND FUTURE SCOPE According to the research, there are several extra factors that should be taken into account when creating a wearable antenna as opposed to a tra­ ditional antenna. A variety of different substances may be utilized to create these modified antennas. To create an antenna design which complies with the wearable antenna gathering analysis, SAR, measurements with various antenna bending, and on-body measurements must be evaluated. The future of these modified wearable antennas is bright and promises to keep up with the expansion of the wireless communication industry. Medical devices that use wireless technology to control internal activities and measure a vari­ ety of physiological indicators are rapidly expanding. Some of these devices are implanted, while others are worn on the body. Implanted devices with biosensing and actuation, for example, can control heart function, monitor heart rate, and provide such a valuable smart wearable sensor system for applications in healthcare electrically stimulating neurons and head pres­ sure. Biomedical sensor technology, the IoT, sophisticated wireless network technology, and sports and fitness will all require tight multidisciplinary col­ laboration. Based on the findings of this chapter, it is feasible to construct antennas with the optimum characteristics and aid antenna engineers in their decision-making by considering significant elements in antenna creation. The creation of elevated fabric substrate antennas capable of overcoming the adverse effects of the human body is the future path for wearable anten­ nas in human interaction applications. When creating antennas for wearable technology, these aspects demand special consideration. While designing wearable antennas, developers should pay close attention to structural defor­ mation, accuracy and precision in antenna production techniques, and size. REFERENCES 1. Chowdhury, M.Z., Shahjalal, M., Ahmed, S. and Jang, Y.M., 2020. 6G wireless communication systems: Applications, requirements, technologies, challenges, and research directions. IEEE Open Journal of the Communications Society, 1, pp. 957–975. 2. Asam, M., Jamal, T., Adeel, M., Hassan, A., Butt, S.A., Ajaz, A. and Gulzar, M., 2019. Challenges in wireless body area network. International Journal of Advanced Computer Science and Applications, 10(11). 3. Ramdani, S. and Pratama, I., 2019. October. Single Coaxial Feed Microstrip GPS Antenna Aimed at Wearable Device Application. In 2019 IEEE Conference on Antenna Measurements & Applications (CAMA) (pp. 247–250). IEEE. 4. Paracha, K.N., Rahim, S.K.A., Soh, P.J. and Khalily, M., 2019. Wearable anten­ nas: A review of materials, structures, and innovative features for autonomous communication and sensing. IEEE Access, 7, pp. 56694–56712.

Review on Wearable Antennas

113

5. El Gharbi, M., Fernández-García, R., Ahyoud, S. and Gil, I., 2020. A  review of flexible wearable antenna sensors: Design, fabrication methods, and applica­ tions. Materials, 13(17), p. 3781. 6. Ghodake, A.P. and Hogade, B.G., 2020. A review of wearable antenna. Interna­ tional Journal of Electronics, 12(1), pp. 13–18. 7. Ali, U., Ullah, S., Shafi, M., Shah, S.A., Shah, I.A. and Flint, J.A., 2019. Design and comparative analysis of conventional and metamaterial-based textile anten­ nas for wearable applications. International Journal of Numerical Modelling: Electronic Networks, Devices and Fields, 32(6), p.e2567. 8. Casula, G.A. and Montisci, G., 2019. A design rule to reduce the human body effect on wearable PIFA antennas. Electronics, 8(2), p. 244. 9. Almohammed, B., Ismail, A. and Sali, A., 2021. Electro-textile wearable anten­ nas in wireless body area networks: Materials, antenna design, manufacturing techniques, and human body consideration—a review. Textile Research Journal, 91(5–6), pp. 646–663. 10. Çelenk, E. and Tokan, N.T., 2022. All-textile on-body antenna for military appli­ cations. IEEE Antennas and Wireless Propagation Letters, 21(5), pp. 1065–1069. 11. Ashyap, A.Y., Dahlan, S.H.B., Abidin, Z.Z., Abbasi, M.I., Kamarudin, M.R., Majid, H.A., Dahri, M.H., Jamaluddin, M.H. and Alomainy, A., 2020. An over­ view of electromagnetic band-gap integrated wearable antennas. IEEE Access, 8, pp. 7641–7658. 12. Tanaka, M. and Jae-Hyeuk, J., 2003. Wearable microstrip antenna. In IEEE Antennas and Propagation Society International Symposium. Digest. Held in conjunction with: USNC/CNC/URSI North American Radio Sci. Meeting (Cat. No. 03CH37450), Columbus, OH (pp.  704–707), vol. 2. doi: 10.1109/ APS.2003.1219333. 13. Hertleer, C., Rogier, H., Vallozzi, L. and Declercq, F., 2007. A Textile Antenna Based on High-Performance Fabrics. In The Second European Conference on Antennas and Propagation, EuCAP 2007 (pp.  1–5). Edinburgh. doi: 10.1049/ ic.2007.1085. 14. Klemm, M. and Troster, G., 2006. Textile UWB Antenna for On-Body Com­ munications. In 2006 First European Conference on Antennas and Propagation (pp. 1-4). Nice, France. doi: 10.1109/EUCAP.2006.4584865. 15. Santas, J.G., Alomainy, A. and Hao, Y., 2007. Textile Antennas for On-Body Communications: Techniques and Properties. In The Second European Confer­ ence on Antennas and Propagation, EuCAP 2007 (pp.  1–4). Edinburgh. doi: 10.1049/ic.2007.1064. 16. Ahmad, A., Faisal, F., Ullah, S. and Choi, D.Y., 2022. Design and SAR analysis of a dual band wearable antenna for WLAN applications. Applied Sciences, 12(18), p. 9218. 17. Zu, H.R., Wu, B., Zhang, Y.H., Zhao, Y.T., Song, R.G. and He, D.P., 2020. Cir­ cularly polarized wearable antenna with low profile and low specific absorption rate using highly conductive graphene film. IEEE Antennas and Wireless Propa­ gation Letters, 19(12), pp. 2354–2358. 18. Varma, S., Sharma, S., John, M., Bharadwaj, R., Dhawan, A. and Koul, S.K., 2021. Design and performance analysis of compact wearable textile antennas

114

19. 20.

21. 22.

23. 24. 25. 26. 27.

28.

Advances in Microwave Engineering for IoT and body-centric communication applications. International Journal of Antennas and Propagation, 2021, pp. 1–12. Mustafa, A.B. and Rajendran, T., 2019. An effective design of wearable antenna with double flexible substrates and defected ground structure for healthcare monitoring system. Journal of Medical Systems, 43, pp. 1–11. Nguyen, T.H., Nguyen, T.L.H. and Vuong, T.P., 2019, March. A printed wearable dual band antenna for remote healthcare monitoring device. In 2019 IEEE-RIVF International Conference on Computing and Communication Technologies (RIVF) (pp. 1–5). IEEE. Rana, M. and Mittal, V., 2020. Wearable sensors for real-time kinematics analy­ sis in sports: A review. IEEE Sensors Journal, 21(2), pp. 1187–1207. Govindan, T., Palaniswamy, S.K., Kanagasabai, M., Kumar, S., Rao, T.R. and Kannappan, L., 2021. RFID-Band Integrated UWB MIMO Antenna for Wear­ able Applications. In 2021 IEEE International Conference on RFID Technology and Applications (RFID-TA) (pp. 199–202). IEEE. Sabban, A., 2019. Small new wearable antennas for IOT, medical and sport applications. In 2019 13th European Conference on Antennas and Propagation (EuCAP) (pp. 1–5). IEEE. Jacob, S. and Sonadevi, S., 2022. Antenna Design and Analysis for Narrow Band Internet of Things Applications. In Antenna Design for Narrowband IoT: Design, Analysis, and Applications (pp. 162–180). IGI Global. Kumar, A., Ranjan, P. and Saini, V., 2022. Smart irrigation system using IoT. In Agri-Food 4.0. Emerald Publishing Limited. De, A., Roy, B., Bhattacharya, A. and Bhattachaqee, A.K., 2021. Bandwidthenhanced ultra-wide band wearable textile antenna for various WBAN and Internet of Things (IoT) applications. Radio Science, 56(11), pp. 1–16. Bhattacharya, A., Roy, B., Caldeirinha, R.F. and Bhattacharjee, A.K., 2019. Low-profile, extremely wideband, dual-band-notched MIMO antenna for UWB applications. International Journal of Microwave and Wireless Technologies, 11(7), pp. 719–728. Saini, V., Shah, P. and Sekhar, R., 2022, December. MATLAB and Simulink for Building Automation. In 2022 IEEE Bombay Section Signature Conference (IBSSC) (pp. 1–6). IEEE.

Chapter 8

A Review of Design Challenges of Metamaterial-Inspired Body-Worn Antennas Moumita Bose , Aparna Kundu , Abhishek Sarkhel, and Ujjal Chakraborty

8.1 INTRODUCTION With the introduction of 5G networks, global data demand has increased and will continue to rise in the near future [1]. As such, conformal, handy, and portable wireless devices are in high demand; among them, unlicensed frequency bands like Industrial Scientific and Medical, WiMAX, Wi-Fi, WLAN, etc., are of lucrative application for local wireless communication, sensing, the Internet of Things, human consensus, and 5G mobile integrated devices. The future of upcoming technology is handy, robust, and trending in use, which has called for flexible antenna [2] and wearable devices to be developed. Figure 8.1 [3] depicts the adoption of wearable devices and the architecture of Internet of Things [4], which also includes wearable com­ munication in 5G. In our daily life, clothing is a very essential part, and integrating electronic or electrical devices along with textiles results in smart clothing, which can find application in the medical sector, defence sector, and many more [5]. The demand for wearable antennas is increasing progres­ sively, as they are light in weight, easy to carry, and have an in-house fabrica­ tion facility. Its flexible nature makes it perform better in different bending situations when placed on the human body. Metamaterial used for designing wearable antennas provides miniaturisation facilities as well as a decrease in back-radiation to improve the specific absorption rate. When exposed to electromagnetic waves, the human body suffers greatly [6–8]. In our day-to­ day lives, this metamaterial-based flexible wearable antennas can be used in different health monitoring applications [9] and safety-based systems. Use of metamaterial can improve antenna performance for narrowband [10–12], dual band [13–16], and wideband [17–19] antennas by minimising backradiation and the specific absorption rate. Article [20] provides an uneven ultra-wideband antenna on denim material for wireless body area network application, while [21] provides material features of autonomous communi­ cation and sensing of wearable antennas. The aim of this chapter is to cover some recent works on metamaterial­ inspired wearable antennas and their practical design challenges. Some DOI: 10.1201/9781003459880-8

115

116

Advances in Microwave Engineering

Figure 8.1 Wearable device adoptions: from a medical sensor to entertainment helmet [3].

application-oriented structures are considered to encounter different design challenges by invoking appropriate excitation and boundary conditions for obtaining the negative permittivity, permeability, and refractive index at desired frequencies. The selection of a flexible substrate is also impor­ tant. Wearable antennas require high bandwidth with small dimensions. The wearable metamaterial antennas must comply with Institute of Electrical and Electronics Engineers (IEEE) C95.1–1999 and IEEE C95.1–2005 standards for an average specific absorption rate value that should be 1.6 W/kg for 1 g of tissue and 2 W/kg for 10 g of tissue. Metamaterial-based wearable anten­ nas are designed such that their efficiencies, radiation patterns, and imped­ ance [22] should not degrade when they come into contact with the human body, even in motion. The bending analysis has to be taken into account for a tolerable degree of freedom. This chapter collectively assembles metama­ terial-inspired antennas, which will pave the way for wireless portable com­ munication, sensing physical miniaturization, and specific absorption rate for the future 5G and Internet of Things wearable devices. 8.2 METAMATERIAL-INSPIRED DUAL WIDEBAND WEARABLE ANTENNA FOR WIRELESS APPLICATIONS Figure 8.2 depicts a dual-band wearable antenna inspired by metamaterial on a jeans substrate for on-body and off-body communication in the GSM 1800 MHz, WLAN, and WiMAX bands, with detailed dimensions given in

A Review of Design Challenges of Metamaterial-Inspired

117

Figure 8.2a Geometry of metamaterial unit cell [23].

Figure 8.2b Analysis setup of unit cell in HFSS [23].

article [23]. The antenna’s performance deteriorated when it was placed on the surface of the human body. This structure was  simulated using Ansys HFSS with proper boundary conditions and excitation to obtain the desired magnitude and phase of the scattering parameter. This scattering parameter is used for the extraction of material parameters like permittivity, permeability, and refractive index using MATLAB. For designing double-negative (DNG) metamaterial, Rich­ ards and Ziolkowski’s DNG media theory is used for small losses where

118

Advances in Microwave Engineering

material parameters follow the following relations as given in Equations (8.1–8.3) [23]:

æ 2 öæ 1 ­ S21 ­ S11 ö Er » ç ÷ç ÷ è jk0 d øè 1 + S21 + S11 ø

(8.1)

æ 2 ö æ 1 ­ S21 + S11 ö mr » ç ÷ç ÷ è jk0 d ø è 1 + S11 ­ S11 ø

(8.2)

n » ­ E r mr

0 .5

é m¢ 1 æ E' + ê1 + j çç 2 è j E r E 0 j m r m0 ëê

öù ÷÷ú ø ûú

(8.3)

The characteristics of unit cells are studied by varying the height and dimen­ sion of the antenna substrate. A change in permeability and permittivity is observed as height changes. The consideration was to obtain negative permeability and permittivity in the desired band. The simulated result for material parameters versus frequency for 1.5 mm substrate height is shown in Figure 8.3a. The effect of changing the substrate dimension on S11 and the upper and lower bandwidth was observed, as shown in Figure 8.3b. It signi­ fies that an antenna has two resonant bands, from 1.6 GHz to 2.56 GHz and from 4.24 GHz to 7 GHz. Antenna performance is affected by bend­ ing. When it is used for on-body or off-body communication, it should be conformal to the human body. The human body’s material property changes

Figure 8.3a Variation of metamaterial parameters with frequency at substrate height 1.5 mm [23].

A Review of Design Challenges of Metamaterial-Inspired

119

Figure 8.3b Simulated S11 parameter for different substrate dimensions [23].

Figure 8.3c Antenna mounted on cubic human tissue model [23].

with frequency, so analysing the effect of a multiband antenna on it is a challenging job. To study the on-body and off-body effects of this metamate­ rial antenna, a computational simulation was done on an equivalent section of a human body model, as shown in Figure 8.3c. Its material properties at 2.4 GHz and effect on S11 are studied with the antenna mounted on a

120

Advances in Microwave Engineering

Figure 8.3d Simulated S11 parameter with on-body and off-body effect [23].

cubic human model with a gap of ‘g’ between the human body and antenna to encounter the practical challenges of a conformal antenna. The mutual coupling between the antenna and the human body affects antenna perfor­ mance, as illustrated in Figure 8.3d. Article [24] describes another dual-band wearable antenna on a jeans sub­ strate. In this paper, the antenna with a split-ring resonator operates at 2.32 GHz and 3.52 GHz, as visualised in Figure 8.4b. The interior and exterior radius of a circular ring resonator are 5.14 mm and 5.43 mm, respectively. The drawback of this kind of structure for dual resonant bands is its overall increased size.

8.2.1 A Novel Wearable Metamaterial Fractal Antenna for Wireless Applications Figure 8.5c depicts the steps of evolution of a novel multiband wearable fractal metamaterial antenna along with top and ground geometry (see Fig­ ure 8.5a and b) designed for GPS, WiMAX, and Wi-Fi band applications [25]. The paper reveals the effect of a spiral metamaterial in the ground plane upon a fractal patch makes permittivity, permeability, and refractive index negative, as shown in Figure 8.5d. It consequently reduces the spe­ cific absorption rate and makes antenna radiation less absorbed by human tissue, which is a prime requirement for wearable applications. Another advantage of using spiral metamaterial with a fractal antenna is that it

A Review of Design Challenges of Metamaterial-Inspired

Figure 8.4a Dual band fabricated antenna with SRR [24].

Figure 8.4b Simulated and measured S11 with SRR [24].

121

122

Advances in Microwave Engineering

Figure 8.5a The fractal antenna with third iteration [25].

Figure 8.5b The fractal antenna’s ground geometry [25].

A Review of Design Challenges of Metamaterial-Inspired

123

Figure 8.5c Steps of evolution [25].

Figure 8.5d MATLAB simulated metamaterial parameters [25].

improves bandwidth performance, as shown in Figure 8.5e. In this design, the third iteration is used to increase the path length of the current, causing a shift in resonance frequency towards lower bands and improving band­ width. The iteration length of the fractal antenna is calculated using the equation denoted in [25]. It has a maximum specific absorption rate value of 0.925 W/Kg, which is well suited for wearable purposes and satisfies international safety standards at resonant frequency. This type of antenna is ideal for use in life jackets during the search for a human body in the event of an accident.

124

Advances in Microwave Engineering

Figure 8.5e Variation of S11 with frequency for third iteration of the wearable antenna (with and without) metamaterials [25].

8.2.2 Radiation Pattern Reconfigurable Wearable Antenna Based on Metamaterial Structure In [26], a radiation pattern reconfigurable metamaterial-based antenna in the ISM band (2.4 GHz) is designed as in Figure 8.6a. A dispersion diagram using Equations (8.4 and 8.5) [26] is used to analyse the resonance of an inductorloaded patch antenna between the zeroth and positive first-order modes.

n p =

1 ­ S11S22 + S12 S21 2S21

(8.4)

mn p = p m

(8.5)

Figure 8.6a Reconfigurable antenna [26].

A Review of Design Challenges of Metamaterial-Inspired

125

Figure 8.6b Dispersion diagram of unit cell [26].

where β, p, m, and n are phase constants, unit cell size, antenna having the number of unit cells, and resonance modes, respectively. The dispersion dia­ gram recovered with calculated S-parameter values considering a unit cell is presented in Figure 8.6b. The transmission line vias were connected to the edges of the patch through switches. When the switches are turned off, a disconnected transmission line causes the antenna to function as a simple patch and radiate in broadside mode. The patch has a half-wavelength of 2.45 GHz, an n of one, and an m of three. Thus, each unit cell has a 60-degree delay. When switches are on, shunt inductors connected as loaded vias generate a phase delay of 0 degrees at 2.45 GHz and the antenna operates in zero resonance mode, having a uniform distributed electric field throughout the patch. Now the antenna radiates in an omnidirectional pattern. Using switches, the patch is converted to metamaterial, and it resonates with the same 2.45 GHz frequency, but its radiation pattern changes from a broadside to an omnidirectional pattern, and metamaterial accounts for diversity in the radiation pattern. The main difficulty with this type of antenna being conformal to the human body is that it must withstand bending without changing its reso­ nance frequency. This is achieved by not reducing the effective magnetic current length of the patch while bending. This type of antenna is well suited for off-body (omnidirectional) and on-body (broadside) use by switching radiation pattern reconfiguration.

8.2.3 Compact All-Textile, Dual-Band Antenna Loaded with Metamaterial-Inspired Structure This wearable antenna [27] shown in Figure 8.7a proposes an alternate and feasible solution for dual band operation using metamaterial for wireless local area network (WLAN) applications. Ways were adopted for dual band

126

Advances in Microwave Engineering

Figure 8.7a The antenna [28].

operation, like using parasitic patches and staked patches. Patches with slot topology have shortcomings like a significant increase in size, complexity in fabrication, etc. With the use of flexible substrates and slots, the current dis­ tribution is affected, resulting in radiation distortion. Side radiation increases coupling between human body and antenna. In this design, the right-handed structure (outer patch) is loaded with a composite right- or left-handed trans­ mission line (inner mushroom-like structure) acting as metamaterial struc­ ture with a patch. With the introduction of a composite right- or left-handed transmission line loaded metamaterial, not only is miniaturisation obtained but also it opens possibilities of multifrequency operation i.e. dual band operation in conjunction with the right-hand structure at lower frequencies, as well as the structure’s compactness and simplicity, make it ideal for inte­ gration in a handheld wearable or portable device. The design challenges of operating at low and high frequencies with a symmetrical radiation pattern

A Review of Design Challenges of Metamaterial-Inspired

127

Figure 8.7b 1D CRLH-TL and its equivalent circuit [28].

can be understood by deducing equivalent circuits, as shown in Figure 8.7b, from a transmission line model for similar kinds of structures [28]. In this transmission line model L'µS, C'µS are inductance and capacitance per unit length and are of a microstrip structure with length d/2 on both sides. Along with LH (left handed), the effect is contributed by coupling between adjacent cells (CL) and via to the ground inductance (LL), whereas the RH effect is due to the current flux (LR) and parallel plate capacitor (CR) between the metal patch mushroom and ground plane constituting the composite right- or left-handed area as a whole of unit cell length (P). The rectangular patch increases the coupling (CL), which helps to lowers the frequency of operation at resonance for metamaterial. M is the number of unit cells and ℓ is total length of composite right- or left-handed transmis­ sion line such that ℓ = Mp and total length L = d + ℓ. With the help of this model dispersion relation from eigen-frequencies, working frequencies can be determined, or once the antenna is ready, a scattering parameter may be used for it. One of the necessary conditions for a homogeneous structure of composite right- or left-handed is the size of the unit cell (p